New consolidation process inspired from making steamed bread to prepare Si3N4 foams by protein foaming method

A new consolidation process had been developed for preparing Si₃N₄ ceramic foams by using protein foaming method, which was inspired from the preparation of steamed bread. The main advantage of this consolidation process was no crack development during foamed slurry consolidation process. By using this new consolidation, Si₃N₄ ceramic foams with open porosities of 79.6–87.3% and compressive strength of 2.5–22 MPa were prepared. Protein addition and solid content on mechanical properties and pore structures of the as-prepared ceramic foams were investigated. Results indicated that the open porosity decreases with protein addition and solid content while compressive strength increased with solid content. With the increase of solid content, pores of the ceramic foams became regular in shape and uniform in size while both size and number of windows on the walls decreased.     

Effects of heating rate on the structure and properties of SiOC ceramic foams derived from silicone resin

Silicon oxycarbide ceramic foams were fabricated in a single step manufacturing process using in situ foaming of SiOC powders loaded silicone resin. The effects of heating rate on the porosity, compressive strength and microstructure of the ceramic foams were investigated. The porosity (total and open) increased firstly and then decreased with increasing heating rate. It was possible to control the total and open porosity of ceramic foams within a range of 81.9–88.2% and 62.4–72.5% respectively, by adjusting the heating rate from 0.25 °C/min to 3 °C/min while keeping the silicone resin content at 90 vol%. However, the compressive strength decreased with increasing the heating rate progressively, and the average compressive strength of the foams was in the range of 1.0–2.3 MPa. Micrographs indicated that the ceramic foams which cross-linked at a heating rate less than 1 °C/min had a well-defined open-cell and regular pore structure.     

Processing of silica foam using steam heating and its characterization

Silica foams with 50–86 vol.% porosity have been developed through steam-heating route using slurries containing ovalbumin as binder, as well as sucrose and colloidal silica as additives. On steam-heating, only 1 h is required for drying of as-cast foams, as the cell-walls being restrained from shrinking by intra-cellular gas pressure, and simultaneously strengthened by ovalbumin protein coagulation, show minimum damage. Scanning electron microscopic studies of sintered foams have shown near-spherical pores with size distribution having mean of ≈250–300 μm. These pores appear interconnected through finer pores of ≈15–25 μm size along their walls. Solid loading, binder and sucrose concentrations of slurries for optimum viscosity have been obtained through rheological studies to tailor desirable pore content and size distributions in the sintered foams. Young's moduli and compressive strengths are found to be in the ranges of 14.4–544 MPa and 0.3–8.6 MPa, respectively for sintered foams having ≈55–90 vol.% porosity content.     

Foaming strategies for bioabsorbable polymers in supercritical fluid mixtures. Part II. Foaming of poly(ɛ-caprolactone-co-lactide) in carbon dioxide and carbon dioxide + acetone fluid mixtures and formation of tubular foams via solution extrusion

This paper reports on the foaming of poly(ɛ-caprolactone-co-lactide) in carbon dioxide and carbon dioxide + acetone mixtures. Experiments were carried out in specially designed molds with porous metal surfaces and fluid circulation features to generate foams with uniform dimensions at 60, 70 and 80 °C at pressures in the range 7–28 MPa. Depending upon the conditions, foams with pores in the range from 5 to 200 μm were generated. Adding acetone to carbon dioxide improved the uniformity of the pores compared to foams formed by carbon dioxide alone. In addition, a unique high-pressure solution extrusion system was designed and used to form porous tubular constructs by piston-extrusion of a solution from a high-pressure dissolution chamber through an annular die into a second chamber maintained at controlled pressure/temperature and fluid conditions. Long uniform porous tubular constructs with 6 mm ID and 1 mm wall thickness were generated with glassy polymers like poly(methyl methacrylate) by extruding solutions composed of 50 wt% polymer + 50 wt% acetone, or 25 wt% polymer + 10% acetone + 65% carbon dioxide at 70 °C and 28 MPa. Pores were in the 50 μm range. The feasibility of forming similar tubular constructs were demonstrated with poly(ɛ-caprolactone-co-lactide) as well. Tubular foams of the copolymer with interconnected pores with pore sizes in the 50 μm range were generated by extrusion of the copolymer solution composed of 25 wt% polymer + 10 wt% acetone + 65 wt% carbon dioxide at 70 °C and 28 MPa. Reducing the acetone content in the solution led to a reduction of pore sizes. Comparisons with the foaming behavior of the homopolymer poly(ɛ-caprolactone) that were carried out in the molds with porous metal plates show that the foaming behavior of the copolymer is more akin to the foaming behavior of the caprolactone homopolymer component.     

Effect of additives on the pore evolution of zirconia based ceramic foams after sintering

A new superplasticity foaming method was used to form zirconia-based ceramic foams. Silica and alumina were chosen as additives because they facilitate the 2D superplastic deformation. The effects of these additives on macroscopic pore evolution were examined after heat treatment for up to 40 h. The addition of silica or alumina also enhanced the 3D deformation during superplasticity foaming. The total porosity of mono-foams made from 3 mol% yttria-stabilised zirconia without additives increased with heat treatment for up to 24 h, and then levelled off. The porosity of silica-dispersed foam was greater than that without additives and continued to increase for up to 40 h. Conversely, the porosity of alumina-dispersed ceramic foam reached saturation within 8 h. Consequently, the porosity of alumina-dispersed foam was greater than that without additives after heating for 8 h, while the latter exceeded the former with prolonged heating for more than 16 h. The detailed effects of alumina dispersion on the foam development behaviour were examined in connection with the microstructure.     

Recycling of harmful waste lead-zinc mine tailings and fly ash for preparation of inorganic porous ceramics

The porous ceramics were prepared by directly sintering of lead-zinc mine tailings and fly ash as the raw materials without any additional sintering and foaming agent. The effects of fly ash addition on the crystalline phases, pore structure, physical–chemical porosities and mechanical strength were investigated. The results showed that the bulk density decreased firstly and then increased while the porosity and water absorption presented the opposite tendency with the increase of fly ash content. Meanwhile, the chemical stability improved and the flexural strength had the same variation tendency of the bulk density. The phase evolution of sample with 60 wt% fly ash addition indicated that anorthite phase was formed at low temperature (1000 °C). The thermal behavior illustrated that the foaming process was initiated by the reaction of internal constituents in the lead-zinc mine tailings. Different pore structures indicated different foaming mechanisms that probably occurred at different temperatures. The porous ceramics with 60 wt% fly ash addition exhibited excellent properties, including bulk density of 0.93 g/cm³, porosity of 65.6%, and flexural strength of 11.9 MPa.     

Porous alumina ceramics prepared with wheat flour

It is shown that wheat flour can be used as a pore-forming and body-forming agent in ceramic technology. In contrast to pure native starch, however, the pores do not result from the swelling starch granules alone but are mainly due to protein-assisted foaming. Therefore the porosity is significantly higher and the pore size larger than that resulting from the starch granules alone, and the wet milling time applied for homogenizing the ceramic suspensions becomes the most critical process parameter. Alumina suspensions with 70 wt.% alumina and 20–30 vol.% wheat flour with different initial particle size (fine grade and semolina, respectively) have been prepared using milling times of up to 8 h. Porosities of up to approx. 60% can be achieved with only 20 vol.% of flour or semolina after 8 h of milling time, with the cell sizes (diameters of pore cavities resulting from foam bubbles) being essentially independent of the milling time (median diameters of 120–240 μm). Effective pore throat sizes (i.e. diameters of cell windows or channels between cells), measured via mercury porosimetry, are 1–2 μm for short milling times (2–3 h), but for long milling times (8 h) they change by more than one order of magnitude to median sizes of 20–30 μm, closely corresponding to the median size of wheat starch granules (approx. 20 μm).     

Silicon carbide-based foams derived from foamed SiC-filled phenolic resin by reactive infiltration of silicon

Macro-cellular porous silicon carbide-based foams were fabricated by reactive infiltration of melt silicon into porous carbonaceous preforms pyrolyzed from foamed SiC-filled phenolic resins (PF). The SiC-filled PF foams were prepared at 80 °C with different heating rate. The effect of heating rate on the foaming behavior of the liquid SiC-filled PF mixture and the microstructure of the foams were investigated. The foamed SiC-filled PF was then pyrolyzed at 1000 °C and infiltrated by melt Si at 1600 °C, leading to the formation of open macro-cellular structure. At a heating rate of 6 °C min⁻¹, Si-infiltrated foams with a porosity of ~72% and a mean pore size of ~0.5 mm were obtained. The Si-infiltrated foams with dense struts mainly inherited the pore structure of pyrolyzed preforms. The main phases of SiC-based foams were α-SiC, β-SiC and the remnant Si, which contributed to high compressive strength of the SiC-based foams.     

Preparation of finely macroporous SiOC foams with high mechanical properties and with hierarchical porosity via pyrolysis of a siloxane/epoxide composite

Mechanically strong SiOC foams were prepared via pyrolysis of polysiloxane composites, into which 20–70 wt% of epoxy powder were incorporated as sacrificial filler. The chosen epoxy filler degrades practically quantitatively during the pyrolysis in nitrogen, due to a high content of polyoxypropylene chains. The pyrolysis of the composite precursors yielded SiOC foams with apparent densities between 1.31 and 0.62 g/cm³, which corresponded to macro-porosities of 35–69%. A hierarchical porosity was obtained due to a relatively wide distribution of the sacrificial filler grains׳ size. Compressive strength between 15 and 38 MPa was achieved, depending on the apparent density of the SiOC foams: the best result was obtained for the foam with 56% porosity. In the case of denser foams, their strength was reduced by the presence of pyrolysis cracks, while at 70% porosity, the thinner pore walls led to a reduced strength. The elastic modulus of the most promising foam (56% porosity) was found to be 10 GPa.     

Preparation and characterization of porous mullite ceramics via foam-gelcasting

Porous mullite ceramics were prepared via foam-gelcasting using industrial grade mullite powder as the main raw materials, Isobam-104 as the dispersing and gelling agent, sodium carboxymethyl cellulose as the foam stabilizing agent, and triethanolamine lauryl sulfate as the foaming agent. The effects of processing parameters such as type and amount of additive, solid loading level and gelling temperature on rheological properties and gelling behaviors of the slurries were investigated. The green samples after drying at 100 °C for 24 h were fired at 1600 °C for 2 h, and the microstructures and properties of the resultant porous ceramic samples were characterized. Based on the results, the effects of foaming agent on the porosity level, pore structure and size and mechanical properties of the as-prepared porous mullite ceramics were examined. Porosity levels and pore sizes of the as-prepared samples increased with increasing the foaming agent content up to 1.0%, above which both porosity levels and pore sizes did not change. The compressive strength and flexural strength of the as-prepared sample with porosity of 76% and average pore size of 313 μm remained as high as 15.3±0.3 MPa and 3.7±0.2 MPa, respectively, and permeability increased exponentially with increasing the porosity.     

Effect of phase composition of natural quartz raw material on characterization of microfiltration ceramic membranes

The results of development of multi-layer ceramic membranes on the basis of natural quartz raw material from Mongolia are presented. The influence of the phase composition and temperature of calcination on the porosity, morphology and mechanical strength of large-porous ceramic support obtained by the method of isostatic pressing was studied. It was established that multi-layer ceramic membranes obtained by the application of water suspension of high-disperse quartz sand of Mongolia and alumosilicate binder with the addition of 15–35 wt% of quartz are characterized by optimal properties. The developed tubular ceramic membranes with the average pore size 5.3 µm, coefficient of air permeability (4.17–4.41)×10⁻¹³ m², productivity by water 46.3–48.0 m³/(h×m²×bar) and mechanical strength 2.27–2.53 MPa are perspective for wide use in microfiltration processes.     

Effect of polymer concentration on porosity and pore size characteristics of alumina membrane substrates prepared by gelcasting

The effect of urea–formaldehyde (UF) polymer concentration on porosity and average pore size of alumina membrane substrates prepared by gelcasting has been studied. The soluble UF oligomers formed in the initial stages of polymerization act as steric stabilizer for alumina particles in the suspension. The porosity and average pore size of the substrate samples decreased with both the decrease of amount of polymer in the gelcast body and the increase of sintering temperature. Membrane substrates obtained by sintering of gelcast bodies containing UF polymer concentrations from 24.3 to 15.6 wt% at temperatures from 1250 to 1450 °C showed porosity and average pore size of 62.5–27 vol% and 0.43–0.20 μm, respectively. The membrane substrates prepared by the gelcasting method had narrow pore size distribution.     

Foaming of flat glass cullet using Si3N4 and MnO2 powders

The introduction of a compound capable of releasing oxygen, such as MnO₂, greatly improves the foaming ability of Si₃N₄ used as foaming agent in soda-lime glass powder, leading to expansion at a relatively low temperature (800–850 °C) and short processing time (7–30 min). The effect is based on the supply of oxygen, in addition to that in the furnace atmosphere. At the highest level of porosity, however, the strength of foams is negatively affected by a coarse microstructure, determined by cell coalescence. The reduction of firing temperature or, above all, the reduction of the processing time, was found to limit the coalescence and significantly improve the strength of the foams.     

Investigating the effect of porosity level and pore former type on the mechanical and corrosion resistance properties of agro-waste shaped porous alumina ceramics

The strength integrity and chemical stability of porous alumina ceramics operating under extreme service conditions are of major importance in understanding their service behavior if they are to stand the test of time. In the present study, the effect of porosity and different pore former type on the mechanical strength and corrosion resistance properties of porous alumina ceramics have been studied. Given the potential of agricultural wastes as pore-forming agents (PFAs), a series of porous alumina ceramics (Al₂O₃-xPFA; x=5, 10, 15 and 20 wt%) were successfully prepared from rice husk (RH) and sugarcane bagasse (SCB) through the powder metallurgy technique. Experimental results showed that the porosity (44–67%) and the pore size (70–178 µm) of porous alumina samples maintained a linear relationship with the PFA loading. Comprehensive mechanical strength characterization of the porous alumina samples was conducted not just as a function of porosity but also as a function of the different PFA type used. Overall, the mechanical properties showed an inverse relationship with the porosity as the developed porous alumina samples exhibited tensile and compressive strengths of 20.4–1.5 MPa and 179.5–10.9 MPa respectively. Moreover, higher strengths were observed in the SCB shaped samples up to the 15 wt% PFA mark, while beyond this point, the silica peak observed in the XRD pattern of the RH shaped samples favored their relatively high strength. The corrosion resistance characterization of the porous alumina samples in hot 10 wt% NaOH and 20 wt% H₂SO₄ solutions was also investigated by considering sample formulations with 5–15 wt% PFA addition. With increasing porosity, the mass loss range in RH and SCB shaped samples after corrosion in NaOH solution for 8 h were 1.25–3.6% and 0.44–2.9% respectively; on the other hand, after corrosion in H₂SO₄ solution for 8 h, the mass loss range in RH and SCB shaped samples were 0.62–1.5% and 0.68–3.3% respectively.     

Mechanical strength and damage tolerance of highly porous alumina ceramics produced from sintered particle stabilized foams

Highly porous alumina particle stabilized foams were prepared by combining the concepts of particle stabilized foams and gelcasting, using sulfonate surfactants and poly vinyl alcohol (PVA) as the gelcasting polymer. The ceramic samples sintered at 1500 °C for 2 h had porosities from 65% to 93%, with pore sizes in two categories: “big pore” around 300 μm and “small pore”, around 100–150 μm, depending on the type and amount of surfactant added. The mechanical behaviour of the foams (axial and diametral compression) depended on the overall porosity and pore size. On average, tensile and compressive strengths around 5 and 16 MPa respectively were measured for samples with bigger pore sizes and larger porosities. Samples with smaller pore sizes and lower porosities produced average values of 12 and 57 MPa for tensile and compressive strengths, respectively. The elastic modulus reached a maximum around 3GPa for “small pore” size samples. The effect of increasing amount of PVA in the samples had a strong effect on the green mechanical strength, but it did not significantly affect the mechanical response of the sintered alumina foams. Large and complex shape sintered components produced using this route showed a remarkable damage tolerance, due to crack tip blunting.     

Preparation of porous Al2TiO5-Mullite ceramic by starch consolidation casting and its corrosion resistance characterization

Stabilized Al₂TiO₅ (AT)-mullite (M) porous ceramics were fabricated by starch consolidation casting using corn starch as curing agent and their microstructure, mechanical properties, pore size distribution and corrosion resistance were examined. Results showed that AT-M porous ceramic with the flexural strength of 11.5 MPa, apparent porosity of about 54.7% and pore size distribution in the range of 1–15 µm could be obtained with 10 wt% corn starch addition. Corrosion resistance results showed mass losses in hot H₂SO₄ solution and NaOH solution for 10 h to decreased from 1.03% to 0.36% and 4.39–2% when the calcination temperature increased from 1400 °C to 1450 °C, which proved these AT-M porous ceramics to possess an excellent corrosion resistance in acidic condition when calcined at 1450 °C.     

Novel ‘inorganic gel casting’ process for the manufacturing of glass foams

A new technique for the production of glass foams was developed, based on alkali activation and gel casting. The alkali activation of soda-lime waste glass powders allowed for the obtainment of well-dispersed concentrated suspensions, undergoing gelification by treatment at low temperature (75 °C). An extensive direct foaming was achieved by mechanical stirring of partially gelified suspensions, comprising also a surfactant. The suspensions were carefully studied in terms of rheological behavior, so that the final microstructure (total amount of porosity, cell size) can be directly correlated with the degree of gelification.A sintering treatment, at 700–800 °C, was finally applied to stabilize the foams, in terms of leaching of alkaline ions. Considering the high overall porosity (88–93%), the newly obtained foams exhibited a remarkable compressive strength, in the range of 1.7–4.8 MPa.     

Surface hierarchical porosity in poly (ɛ-caprolactone) membranes with potential applications in tissue engineering prepared by foaming in supercritical carbon dioxide

This article describes the preparation of porous poly (ɛ-caprolactone), PCL, membranes by supercritical CO₂ (SCCO₂) foaming, displaying surface hierarchical macroporosity which could be tailored by careful control of the pressure, in the range of 150–250 bar, and depressurization processes in several steps, showing also pore interconnectivity between both membrane faces. The membranes exhibited two distinct types of surface macroporosity, the larger with diameter sizes of 300–500 μm were surrounded by and also composed of smaller pores of 15–50 μm (same size as inner pores). Membranes were prepared by solvent casting and submitted to different SCCO₂ foaming. Parameters such as membrane thickness, CO₂ flow, foaming time, pressure, temperature and the depressurization processes (rate and profiles), were varied to determine their influence on final porosity and to decipher which parameters were the most critical ones in terms of surface hierarchical pore organization. No remarkable changes in PCL crystallinity were found when membranes were processed under SCCO₂. Finally, biological evaluation of the porous membranes was achieved by seeding human skin fibroblasts on the prepared membranes. The results, in terms of cell adhesion, spreading, proliferation and metabolic activity indicate that these membranes could hold promise for the fabrication of meshes with controlled porosity for tissue engineering applications.     

The use of egg shells to produce Cathode Ray Tube (CRT) glass foams

Cleaned Cathode Ray Tube (CRT) (panel and funnel) waste glasses produced from dismantling TV and PC colour kinescopes were used to prepare glass foams by a simple and economic processing route, consisting of a direct heating of glass powders at relatively low temperatures (600–800 °C). This study reports on the feasibility of producing glass foams using waste egg shells as an alternative calcium carbonate-based (95 wt%) foaming agent derived from food industry. The foaming process was found to depend on a combination of composition, processing temperature and mixture of raw materials (glass wastes). Hot stage microscopy (HSM), X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize foams and evaluate the foaming ability and the sintering process. The experimental compositions allowed producing well sintered glass foams with suitable properties for some functional applications with environmental benefits such as: (1) reduced energy consumption because of the low heat treatment temperatures used; and (2) materials produced exclusively from residues.     

Particle-stabilized ultra-low density zirconia toughened alumina foams

Zirconia toughened alumina (ZTA) is one of the leading engineering ceramics; it is used in a wide range of components and products in applications for which high strength, high toughness, and high temperature stability are needed. The particle-stabilized direct foaming method has lately become a subject of particular interest. Nevertheless only a few studies on combining ZTA ceramics and particle-stabilized direct foaming have been reported. Therefore, in this study, ultra-low density ZTA foams having single strut wall thickness, cell size ranging from 80 μm to 200 μm, and above 90% porosity were successfully fabricated via the particle-stabilized direct foaming method. Valeric acid was used as particle surface modifier to render the particles partially hydrophobic, which stabilized the air/water interface of the ZTA foams. The sintered foams maintained compressive strength up to 8 MPa with porosity of 90%.