Effect of Na0.5Bi0.5TiO3 on dielectric properties of BaTiO3 based ceramics

In this work, Na_0.5Bi_0.5TiO₃ (NBT) was used to improve the high temperature dielectric properties of Nb, Co-doped BaTiO₃ (BT). Different x was selected (x = 0, 0.02, 0.04, 0.06, 0.08, 0.1, 0.2, 0.3, 0.4) to optimize the ratio of BT to NBT in (1 ? x) BT–xNBT solid solution. The dielectric constant of the original X7R material is about 4900 at room temperature, decreasing to 2500 with NBT addition (x = 0.2). Of important is that the temperature stability was improved with dielectric constant variation being less than ±15% up to 160 °C.     

Compositional range and electrical properties of the morphotropic phase boundary in the Na0.5Bi0.5TiO3–K0.5Bi0.5TiO3 system

We have investigated the Na_0.5Bi_0.5TiO₃–K_0.5Bi_0.5TiO₃ (NBT–KBT) system, with its complex perovskite structure, as a promising material for piezoelectric applications. The NBT–KBT samples were synthesized using a solid-state reaction method and characterized with XRD and SEM. Room-temperature XRD showed a gradual change in the crystal structure from tetragonal in the KBT to rhombohedral in the NBT, with the presence of an intermediate morphotropic region in the samples with a compositional fraction x between 0.17 and 0.25. The fitted perovskite lattice parameters confirmed an increase in the size of the crystal lattice from NBT towards KBT, which coincides with an increase in the ionic radii. Electrical measurements on the samples showed that the maximum values of the dielectric constant, the remanent polarization and the piezoelectric coefficient are reached at the morphotropic phase boundary (MPB) (? = 1140 at 1 MHz; P_r = 40 μC/cm²; d₃₃ = 134 pC/N).     

Dielectric,ferroelectric and field-induced strain behavior of K0.5Na0.5NbO3-modified Bi0.5(Na0.78K0.22)0.5TiO3 lead-free ceramics

Lead-free piezoelectric (1 ? x)Bi_0.5(Na_0.78K_0.22)_0.5TiO₃–xK_0.5Na_0.5NbO₃ (BNKT–xKNN, x = 0–0.10) ceramics were synthesized using a conventional, solid-state reaction method. The effect of KNN addition on BNKT ceramics was investigated through X-ray diffraction (XRD), dielectric, ferroelectric and electric field-induced strain characterizations. XRD revealed a pure perovskite phase with tetragonal symmetry in the studied composition range. As the KNN content increased, the depolarization temperature (T_d) as well as maximum dielectric constant (?_m) decreased. The addition of KNN destabilized the ferroelectric order of BNKT ceramics exhibiting a pinched-type hysteresis loop with low remnant polarization (11 μC/cm²) and small piezoelectric constant (27 pC/N) at 3 mol% KNN. As a result, at x = 0.03 a significant enhancement of 0.22% was observed in the electric field-induced strain, which corresponds to a normalized strain (S_max/E_max) of ～434 pm/V. This enhancement is attributed to the coexistence of ferroelectric and non-polar phases at room temperature.     

Grain size control of lead-free Li0.06(Na0.5K0.5)0.94NbO3 piezoelectric ceramics by Ba and Ti doping

In this study, Ba- and Ti-doped Li_0.06(Na_0.5K_0.5)_0.94NbO₃ [(1 ? x)Li_0.06(Na_0.5K_0.5)_0.94NbO₃–xBaTiO₃ (x = 0–0.07)] ceramics were prepared by using conventional solid state reaction method, and the microstructure and electric properties of these samples were investigated. The grain size distribution of non-doped Li_0.06(Na_0.5K_0.5)_0.94NbO₃ ceramics was relatively wide. The microstructure was composed of grains ranging 1.1–5.0 μm in size. However, with increasing Ba and Ti content, the grain size distribution became narrow and the average grain size decreased from 2.0 to 0.9 μm in size. In particular, the microstructure of x = 0.07 sample was composed of grains ranging 0.5–2.2 μm in size. As a result, the frequency dispersion of dielectric constant for the (1 ? x)Li_0.06(Na_0.5K_0.5)_0.94NbO₃–xBaTiO₃ (x = 0–0.07) ceramics was reduced and the mechanical quality factor Q_m was enhanced with increasing Ba and Ti content.     

Preparation and characterization of K0.5Bi0.5TiO3 particles synthesized by a stirring hydrothermal method

Nanoparticles of potassium bismuth titanate K_0.5Bi_0.5TiO₃ (KBT) with an average particle size of 38 nm were prepared using a stirring hydrothermal method. The pure KBT was obtained in 8 h reaction time instead of 24–48 h for conventional hydrothermal method. X-ray diffraction, Raman spectroscopy and TG analysis were used to check the proportion of hydroxyl group existing into the crude and the calcined KBT. A Hydroxyl group was found to affect the crystallite structure parameters and cell volume. When temperature increases from 25 to 1050 °C, the tetragonal structure presents a c/a ratio which decreases from 1.048 to 1.012. TG analysis and Raman vibration at high frequencies show that c/a is affected by hydroxyl group content below 750 °C and by potassium and bismuth vacancies above this temperature. The ceramic KBT showing a 300 nm size presents an improved ε_r=780 and a dielectric loss tan δ=0.062 at room temperature. Electric conductivity σ_ac was also lowered to 10⁻⁶ (Ω m)⁻¹ with an activation energy change at 673 K from 0.35 to 0.605 eV.     

Lead-free BaTiO3-Bi0.5Na0.5TiO3-Na0.73Bi0.09NbO3 relaxor ferroelectric ceramics for high energy storage

A series of (1-x)(0.65BaTiO₃-0.35Bi_0.5Na_0.5TiO₃)-xNa_0.73Bi_0.09NbO₃ ((1-x)BBNT-xNBN) (x = 0–0.14) ceramics were designed and fabricated using the conventional solid-state sintering method. The microstructure, dielectric property, relaxor behavior and energy storage property were systematically investigated. X-ray diffraction results reveal a pure perovskite structure and dielectric measurements exhibit a relaxor behavior for the (1-x)BBNT-xNBN ceramics. The slim polarization electric field (P-E) loops were observed in the samples with x ≥ 0.02 and the addition of Na_0.73Bi_0.09NbO₃ (NBN) could decrease the remnant polarization (P_r) of the (1-x)BBNT-xNBN ceramics obviously. The sample with x = 0.08 exhibits the highest energy storage density of 1.70 J/cm³ and the energy storage efficiency of 82% at 172 kV/cm owing to its submicron grain size and high relative density. These results show that the (1-x)BBNT-xNBN ceramics may be promising lead-free materials for high energy storage density capacitors.     

Effects of K nonstoichiometry in bismuth layer-structured K0.5+xBi4.5Ti4O15 ceramics

The effects of K nonstoichiometry on phase formation, grain morphology, dielectric and piezoelectric properties of K_0.5+xBi_4.5Ti₄O₁₅ (KBT) were studied in the range of excess up to +2 mol% and deficient down to ?8 mol% of K_0.5. The relative densities of the sintered KBT ceramics with various K contents prepared by a solid state reaction method were all higher than 95%. In all samples, a bismuth layer-structured phase was confirmed, although a secondary phase appeared as K deficiency became larger than ?6 mol%. Piezoelectric coefficient (d₃₃) increased, showing a high of 16 pC/N at x = ?3 mol%, and then decreased with further K deficiency while Curie temperature (T_C) decreased showing a low of 540 °C at x = ?8 mol% from 551 °C at x = 0 mol%. Mechanical quality factor (Q_m) of all samples was in the range of 900–1860.     

Microstructure,ferroelectric and piezoelectric properties of Bi0.5K0.5TiO3-modified BiFeO3–BaTiO3 lead-free ceramics with high Curie temperature

The effects of composition, sintering temperature and dwell time on the microstructure and electrical properties of (0.75 ? x)BiFeO₃–0.25BaTiO₃–xBi_0.5K_0.5TiO₃ + 1 mol% MnO₂ ceramics were studied. The ceramics sintered at 1000 °C for 2 h possess a pure perovskite structure and a morphotropic phase boundary of rhombohedral and pseudocubic phases is formed at x = 0.025. The addition of Bi_0.5K_0.5TiO₃ retards the grain growth and induces two dielectric anomalies at high temperatures (T₁ ～ 450–550 °C and T₂ ～ 700 °C, respectively). After the addition of 2.5 mol% Bi_0.5K_0.5TiO₃, the ferroelectric and piezoelectric properties of the ceramics are improved and very high Curie temperature of 708 °C is obtained. Sintering temperature has an important influence on the microstructure and electrical properties of the ceramics. Critical sintering temperature is 970 °C. For the ceramic with x = 0.025 sintered at/above 970 °C, large grains, good densification, high resistivity and enhanced electrical properties are obtained. The weak dependences of microstructure and electrical properties on dwell time are observed for the ceramic with x = 0.025.     

Enhanced microstructure and electrical properties of Mn-modified Bi0.5(Na0.65K0.35)0.5TiO3 ferroelectric ceramics

Bi_0.5(Na_0.65K_0.35)_0.5TiO₃ (BNKT) and Mn-modified Bi_0.5(Na_0.65K_0.35)_0.5(Mn_xTi_1−x)O₃ (BNKMT-10³x), (x=0.0–0.5%) ferroelectric ceramics were synthesized by solid-state reaction method. Optimization of calcination temperature in Mn-doped ceramics was carried out for the removal of secondary phases observed in XRD analysis. BNKMT ceramics sintered at 1090 °C showed enhanced dielectric, piezoelectric and ferroelectric properties in comparison to pure BNKT. The average grain size was found to increase from 0.35 μm in BNKT to 0.52 μm in Bi_0.5(Na_0.65K_0.35)_0.5(Mn_0.0025Ti_0.9975)O₃ (BNKMT-2.5) ceramics. The dielectric permittivity maximum temperature (T_m) was increased to a maximum of 345 °C with Mn-modification. AC conductivity analysis was performed as a function of temperature and frequency to investigate the conduction behavior and determine activation energies. Significant high value of piezoelectric charge coefficient (d₃₃=176 pC/N) was achieved in BNKMT 2.5 ceramics. Improved temperature stability of ferroelectric behavior was observed in the temperature dependent P–E hysteresis loops as a result of Mn-incorporation. The fatigue free nature along with enhanced dielectric and ferroelectric properties make BNKMT-2.5 ceramic a promising candidate for replacing lead based ceramics in device applications.     

Magneto-dielectric laminated Ba(Fe0.5Nb0.5)O3-Bi0.2Y2.8Fe5O12 composites with high dielectric constant and high permeability

Magneto-dielectric laminated ceramic composites of xBa(Fe_0.5Nb_0.5)O₃-(1-x)Bi_0.2Y_2.8Fe₅O₁₂(BFN-BYIG) with high volume fractions of the giant dielectric constant material BFN (x=10, 30, 50, 70 wt%) were fabricated by the solid-state sintering method. Microstructure, dielectric and magnetic properties of the composites were investigated. The composites possess stable dielectric properties in the frequency range from 100 Hz to 1 MHz with high dielectric constant and low dielectric loss. The maximum permeability of the magneto-dielectric laminated composites reaches up to about 25. And the magnetic behaviors are strongly dependent on the mass ratio of BYIG. The results indicate that such multilayer structures of BFN/BYIG can enhance the permeability and decrease the dielectric and magnetic loss efficiently.     

Synthesis and characterizations of BNT–BT and BNT–BT–KNN ceramics for actuator and energy storage applications

Dielectric and ferroelectric properties of 0.93Bi_0.5Na_0.5TiO₃–0.07BaTiO₃ (BNT–BT) and 0.93Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–0.01K_0.5Na_0.5NbO₃ (BNT–BT–KNN) ceramics were studied in detail. An XRD analysis confirmed the single perovskite phase formation in both the samples. Room temperature (RT) dielectric constant (ε_r) ~1020 and 1370, respectively at 1 kHz frequency were obtained in the BNT–BT and BNT–BT–KNN ceramics. Temperature dependent dielectric and the polarization vs. electric field (P–E) studies confirmed the coexistence of ferroelectric (FE) and anti-ferroelectric (AFE) phases in the BNT–BT and BNT–BT–KNN ceramics. Substitution of KNN into the BNT–BT system decreased the remnant polarization, coercive field and the maximum strain percentage. The energy storage density values ~0.485 J/cm³ and 0.598 J/cm³ were obtained in the BNT–BT and BNT–BT–KNN ceramics, respectively. High induced strain% in the BNT–BT ceramics and the high energy storage density in the BNT–BT–KNN ceramics suggested about the usefulness of these systems for the actuator and the energy storage applications, respectively.     

Dielectric properties and microstructures of non-reducible high-temperature stable X9R ceramics

New X9R dielectrics based on the precursors of (1 ? x) BaTiO₃–xLiTaO₃ (BT–xLT) compositions and containing no lead and bismuth constituents were successfully prepared in this study. After sintering at 1150–1250 °C in a reducing atmosphere of 97%N₂–3%H₂, major phases including BaTiO₃ and Ba₂LiTa₅O₁₅ and a minor phase of Li₂TiO₃ were identified in the sintered ceramics. The intensities of the XRD peaks corresponding to the Ba₂LiTa₅O₁₅ phase rose with the increasing x value in the precursors. The grain sizes of the sintered ceramics appeared to fall in the range between 0.3 and 0.5 μm and slightly increased with the x value of the BT–xLT ceramics. The best composition in term of dielectric properties was found in the BT–0.25LT ceramic, which was marked with a dielectric constant of 895, tan δ of 1.01% and 7.1%, TCCs of ?3.04% and ?14.80%, and electrical resistivities of 9.9 × 10¹² and 1.6 × 10¹² Ω cm, respectively at 25 °C and 200 °C.     

Dielectric behaviors of Nb2O5–Co2O3 doped BaTiO3–Bi(Mg1/2Ti1/2)O3 ceramics

Nb₂O₅ and Nb–Co doped 0.85BaTiO₃–0.15Bi(Mg_1/2Ti_1/2)O₃ (0.85BT–0.15BMT) ceramics were investigated. From XRD patterns, undesired phase was observed when the (Nb₂O₅/Nb-Co) doping levels exceed 3 wt.%/2 wt.%, giving rise to the deteriorate dielectric constant. The 0.85BT–0.15BMT ceramics doped with 2 wt.%Nb₂O₅ was found to possess a moderate dielectric constant (? ～ 1000) and low dielectric loss (tan δ = 0.9%) at room temperature and 1 kHz, showing flat dielectric behavior over the temperature range from ?55 to 155 °C. It was found that the formation of core–shell structure in the BT based ceramics is controlled by the doping sequence of Nb- and Bi-oxides.     

Dielectric behavior and impedance spectroscopy in lead-free BNT–BT–NBN perovskite ceramics for energy storage

The dielectric behavior, impedance spectroscopy and energy-storage properties of 0.85[(1−x)Bi_0.5Na_0.5TiO₃–xBaTiO₃]–0.15Na_0.73Bi_0.09NbO₃ [(BNT–xBT)–NBN] ternary ceramics were investigated. Temperature dependent permittivity curves displayed two depressed anomalies, resulting in significantly improved dielectric temperature stability. (BNT–9BT)–NBN showed a permittivity of 1680 at 150 °C with Δε/ε_150 °C varying no more than ±10% up to 340 °C. From the complex impedance analysis, grain and grain boundary shared the same time constant. The high temperature resistivity followed the Arrhenius law with E_a=1.7–2.0 eV, suggesting intrinsic band-type electronic conduction. The maximum energy-storage density of all the samples reached 1.1–1.4 J/cm³, accompanied with good temperature stability in the range of 25–140 °C. These results indicate that (BNT–xBT)–NBN system should be a promising lead-free material for energy-storage capacitor applications.     

Dielectric and ferroelectric properties of (1 − x)BaTiO3–xBi0.5Na0.5TiO3 ceramics

Lead-free (1 − x)BaTiO₃–xBi_0.5Na_0.5TiO₃ (x = 0.01, 0.02, 0.05, 0.1, 0.2, 0.3) ferroelectric ceramics were fabricated by the conventional ceramic technique. Sintering was made at 1200 °C for 2–4 h in air atmosphere. The crystal structure was investigated by X-ray diffraction. The dielectric and ferroelectric properties were also studied. Room temperature permittivity was found to decrease as Bi_0.5Na_0.5TiO₃ (BNT) content increases. Only the sample with 0.3 mol BNT was found to have relaxor behaviour. The T_c shifted slightly only for BNT addition lower than 0.1 mol. The highest T_c (about 150 °C) was obtained for 0.2 mol BNT addition. The remanent polarization, P_r, decreases whereas the coercive field, E_c, increases monotonously as the BNT content increases.     

Effect of Li2O–V2O5 on the low temperature sintering and microwave dielectric properties of Li1.0Nb0.6Ti0.5O3 ceramics

Li₂O–Nb₂O₅–TiO₂ based ceramic systems have been the candidate materials for LTCC application, due to their high dielectric constant and Q × f value and controllable temperature coefficient in the microwave region. However, the sintering temperature was relatively higher (above 1100 °C) for practical application. In this study, dielectric properties of Li_(1+x−y)Nb_(1−x−3y)Ti_(x+4y)O₃ solid solution were studied with different x and y contents and among them, the Li_1.0Nb_0.6Ti_0.5O₃ composition (x = 0.1, y = 0.1) was selected, due to its reasonable dielectric properties to determine the possibility of low temperature sintering. The effects of 0.17Li₂O–0.83V₂O₅, as a sintering agent, on sinterability and microwave dielectric properties of Li_1.0Nb_0.6Ti_0.5O₃ ceramics were investigated as a function of the sintering agent content and sintering temperature. With addition of 0.17Li₂O–0.83V₂O₅ above 0.5 wt%, the specimens were well densified at a relatively lower temperature of 850 °C. Only slight decrease in apparent density was observed with increasing 0.17Li₂O–0.83V₂O₅ content above 0.75 wt%. In the case of 0.5 wt% 0.17Li₂O–0.83V₂O₅ addition, the values of dielectric constant and Q × f reached maximum. Further addition caused inferior microstructure, resulting in degraded dielectric properties. For the specimens with 0.5 wt% 0.17Li₂O–0.83V₂O₅ sintered at 850 °C, dielectric constant, Q × f and TCF values were 64.7, 5933 GHz and 9.4 ppm per °C, respectively.     

Dependence of dielectric properties on structural characteristics of (Zn1/3A2/3)0.5 (Ti1−xBx)0.5O2 (A = Nb5+, Ta5+, B = Ge4+, Sn4+) ceramics at microwave frequencies

The effects of structural characteristics on the dielectric properties of (Zn_1/3A_2/3)_0.5(Ti_1?xB_x)_0.5O₂ (A = Nb⁵⁺, Ta⁵⁺, B = Ge⁴⁺, Sn⁴⁺) (0.1 ≤ x ≤ 0.3) ceramics were investigated at microwave frequency. The sintered specimens showed solid solutions with a tetragonal rutile structure within the solid solution range of compositions. With an increase of BO₂, the temperature coefficient of resonant frequency (TCF) and dielectric constant (K) decreased with a decrease of oxygen octahedral distortion and dielectric polarizabilites, respectively. However, the quality factor (Qf) of the sintered specimens was increased with BO₂ due to the reduction of Ti⁴⁺ ions. The Qf value of the specimens with A = Ta was higher than that of the specimens with A = Nb.     

Influence of sintering temperature on energy storage properties of BaTiO3–(Sr1−1.5xBix) TiO3 ceramics

The effect of sintering temperature on microstructure, dielectric properties and energy storage properties of BaTiO₃–(Sr_1?1.5xBi_x)TiO₃ (x = 0.09) (BT–SBT) ceramics was investigated. The sintering temperature has pronounced influence on the grain size, shrinkage, and dielectric properties of the BT–SBT ceramics. With increasing sintering temperature, the dielectric constant increases largely. However, the increasing tendency of the dielectric breakdown strength (BDS) is less noticeable but become more evident with the consideration of Weibull modulus. For the BT-SBT ceramics, the unreleased energy density decreases and the electric field stability of the energy storage efficiency enhances with the increase of sintering temperature.     

Energy-storage properties of Bi0.5Na0.5TiO3-BaTiO3-KNbO3 ceramics fabricated by wet-chemical method

0.93Bi_0.5Na_0.5TiO₃-0.07BaTiO₃ (BNTBT) and KNbO₃ (KN) powders with average particle size of ∼50 nm and ∼300 nm were synthesized by sol-gel method and hydrothermal method, respectively. Then, (1 − x)(BNTBT)-xKN (BNTBT-KN, x = 0, 0.01, 0.03, 0.05, 0.07) ceramic samples were prepared using these two powder precursors. The structure, dielectric and energy-storage properties of BNTBT-KN ceramics were comprehensively investigated. All the ceramic samples were in single perovskite structure, indicating that KN can completely dissolve into BNTBT within the studied composition range. BNTBT-KN ceramics exhibited a high dielectric constant at room temperature, being in the order of 1430–1550. Ferroelectric hysteresis loops at room temperature became more slim with the increase of KN content, which largely improved energy-storage density and efficiency. For the composition of x = 0.05, the maximum recoverable energy-storage density reached 1.72 J/cm³ under 16.8 kV/mm, which is superior to linear dielectrics and even some Pb-based systems. All these results demonstrate that 0.95BNTBT-0.05KN fabricated by wet-chemical method is a promising lead-free dielectric material for energy-storage capacitors.     

Physical and electrical properties of Nb doped Bi0.5Na0.5[Zr0.59Ti0.41]O3

This research studied the effect of Nb doping on Bi_0.5Na_0.5[Ti_0.41Zr_0.59]O₃ (when Nb concentration = 0.00, 0.01, 0.03, 0.05, 0.07 and 0.09 mol fraction). Nb doped BNTZ ceramics were fabricated using a conventional mixed-oxide method. All samples were calcined at a temperature of 700 °C for 2 h and sintered at a temperature of 900 °C for 2 h. X-ray diffraction patterns suggested that the compounds possessed rhombohedral perovskite structure. SEM micrographs indicated that average grain size decreased as the amount of Nb additives increased. The electrical resistivity showed a decreasing trend with increasing Nb concentration due to excess charge present in the sample. The dielectric constant and dielectric loss of samples showed no particular trend when Nb was added but the optimum was observed when 0.05–0.07 Nb mol fraction was present in BNTZ ceramics. In this study, both microstructure and donor-type effects played an important role in determining electrical resistivity and dielectric properties of these ceramics.