Influence of sintering conditions on piezoelectric properties of KNbO3 ceramics

A homogeneous KNbO₃ (KN) phase was formed in specimens that were sintered at 1020 °C and 1040 °C, without formation of the K₂O-deficient secondary phase, indicating that the amount of evaporation of K₂O during sintering was very small. However, the KN liquid phase was formed during sintering and assisted the densification of the KN ceramics. A dense microstructure was developed in the specimen sintered at 1020 °C for 6 h and abnormal grain growth occurred in this specimen. A similar microstructure was observed in the specimens sintered at 1040 °C for 1.0 h. The dielectric and piezoelectric properties of the KN ceramics were considerably influenced by the relative density. The KN ceramics sintered at 1020 °C for 6 h, which showed a large relative density that was 95% of the theoretical density, exhibited promising electrical properties: ɛ^T₃₃/ɛ_o of 540, d₃₃ of 109 pC/N, k_p of 0.29, and Q_m of 197.     

Influence of Li2O–B2O3–SiO2 glass on the sintering behavior and microwave dielectric properties of BaO–0.15ZnO–4TiO2 ceramics

This paper reports the investigation of the performance of Li₂O–B₂O₃–SiO₂ (LBS) glass as a sintering aid to lower the sintering temperature of BaO–0.15ZnO–4TiO₂ (BZT) ceramics, as well as the detailed study on the sintering behavior, phase evolution, microstructure and microwave dielectric properties of the resulting BZT ceramics. The addition of LBS glass significantly lowers the sintering temperature of the BZT ceramics from 1150 °C to 875–925 °C. Small amount of LBS glass promotes the densification of BZT ceramic and improves the dielectric properties. However, excessive LBS addition leads to the precipitation of glass phase and growth of abnormal grain, deteriorating the dielectric properties of the BZT ceramic. The BZT ceramic with 5 wt% LBS addition sintered at 900 °C shows excellent microwave dielectric properties: ε_r=27.88, Q×f=14,795 GHz.     

Low-temperature sintering of (K,Na)NbO3-based lead-free piezoceramics with addition of LiF

Dense Li/Ta-codoped KNN-based piezoceramics with d₃₃^* up to 375 pm/V were successfully fabricated by conventional sintering at a temperature as low as 900 °C by using LiF as a sintering additive. The reduction of densification temperature up to 200 °C was realized by a transient liquid phase sintering mechanism, consequently no grain boundary phase was observed in the sintered samples. It was found that the addition of LiF could further shift down the tetragonal–orthorhombic transition point (T_T-O), indicating that a small amount of Li⁺ could diffuse into the A-site of KNN matrix. The introduction of LiF enhanced the linearity of strain curves of the ceramics, which is unambiguously in favor for the actuator application. The present work reveals that low-temperature sintered LiF-doped KNN-based piezoceramics demonstrates promising potential in multilayer-structured actuator applications.     

Densification and mechanical properties of hot-pressed ZrN ceramics doped with Zr or Ti

The densification of hot-pressed ZrN ceramics doped with Zr or Ti have been investigated at 1500–1700 °C. It is shown that either Zr or Ti additive can facilitate the densification process. ZrN with 20 mol% Zr or Ti (named ZNZ and ZNT) sintered at 1700 °C can achieve above 98% relative densities whereas densification temperature up to 2000 °C is necessary for pure ZrN. The densification improvements are attributed to solid solution of Zr or Ti into ZrN to form non-stoichiometric ZrN_1?x or (Zr, Ti)N_1?x. The microstructures and mechanical properties of ZNZ and ZNT samples have been examined. Large grain size and flat fracture surface existed in ZNT sample sintered at 1700 °C, which lead to poor toughness as low as 2.3 MPa m^1/2. On the contrary, the fracture toughness of ZNZ sample sintered at 1700 °C was up to 5.9 MPa m^1/2, attributed to fine and uniform grain size distribution.     

High-strength AlN ceramics by low-temperature sintering with CaZrO3–Y2O3 co-additives

Aluminum nitride (AlN) ceramics with the concurrent addition of CaZrO₃ and Y₂O₃ were sintered at 1450-1700 °C. The degree of densification, microstructure, flexural strength, and thermal conductivity of the resulting ceramics were evaluated with respect to their composition and sintering temperature. Specimens prepared using both additives could be sintered to almost full density at relatively low temperature (3 h at 1550 °C under nitrogen at ambient pressure); grain growth was suppressed by grain-boundary pinning, and high flexural strength over 630 MPa could be obtained. With two-step sintering process, the morphology of second phase was changed from interconnected structure to isolated structure; this two-step process limited grain growth and increased thermal conductivity. The highest thermal conductivity (156 Wm⁻¹ K⁻¹) was achieved by two-step sintering, and the ceramic showed moderate flexural strength (560 MPa).     

Effect of sintering temperature on the structural and magnetic properties of MgFe2O4 ceramics prepared by spark plasma sintering

Spark plasma sintering (SPS) is a powerful technique to produce fine grain dense ferrite at low temperature. This work was undertaken to study the effect of sintering temperature on the densification, microstructures and magnetic properties of magnesium ferrite (MgFe₂O₄). MgFe₂O₄ nanoparticles were synthesized via sol–gel self-combustion method. The powders were pressed into pellets which were sintered by spark plasma sintering at 700–900 °C for 5 min under 40 MPa. A densification of 95% of the theoretical density of Mg ferrite was achieved in the spark plasma sintered (SPSed) ceramics. The density, grain size and saturation magnetization of SPSed ceramics were found to increase with an increase in sintering temperature. Infrared (IR) spectra exhibit two important vibration bands of tetrahedral and octahedral metal-oxygen sites. The investigations of microstructures and magnetic properties reveal that the unique sintering mechanism in the SPS process is responsible for the enhancement of magnetic properties of SPSed compacts.     

Effects of glass additions on the microstructure and dielectric properties of barium strontium titanate (BST) ceramics

Commercial glass frits (lead borosilicate glasses) were employed as the sintering aids to reduce the sintering temperatures of BST ceramics. The effects of the glass content and the sintering temperature on the microstructures, dielectric properties and tunabilities of BST ceramics have been investigated. Densification of BST ceramics of 5 wt% glass content becomes significant from sintering temperature of 1000 °C. The glass content shows a strong influence on the Curie temperature T_c, permittivity and the diffuse transition. X-ray results show all BST ceramics exhibit a perovskite structure and also the formation of a secondary phase, Ba₂TiSi₂O₈. The shift of BST diffraction peaks towards higher angle with increasing the glass content indicates the substitution of Pb²⁺ in Ba²⁺ site, which mainly accounts for the diffuse transition observed in these BST ceramics. BST ceramics with 10 wt% glass additives possess the highest tunability at all four sintering temperatures. A tunability of 12.2% at a bias field of 1 kV/mm was achieved for BST ceramics with 10 wt% glass content sintered at 900 °C.     

Ni4Nb2O9 ceramics prepared by the reaction-sintering process

Fabrication of Ni₄Nb₂O₉ ceramics via a reaction-sintering process was investigated. A mixture of raw materials was sintered into ceramics by bypassing calcination and subsequent pulverization stages. Ni₄Nb₂O₉ phase appeared at 1300 °C and increased with increasing soak time. Ni₄Nb₂O₉ content was found >96% in 1350 °C/2 h sintering pellets. A density of 5.71 g/cm³ was obtained for pellets sintered at 1350 °C for 2 h. This reaches 96.5% of the theoretical density. As the sintering temperature increased to 1350 °C, an abnormal grain growth occurred and grains >100 μm could be found. ?_r of 15.4–16.9 are found in pellets sintered at 1200–1300 °C. Q × f increased from 9380 GHz in pellets sintered at 1200 °C to 14,650 GHz in pellets sintered at 1250 °C.     

Low temperature fabrication of lead-free KNN-LS-BS ceramics via the combustion method

Lead-free piezoelectric 0.992(0.95K_0.5Na_0.5NbO₃–0.05LiSbO₃)–0.008BiScO₃; KNN-LS-BS ceramics were successfully prepared using the combustion method. The highest % perovskite phase was found in the sample calcined at 700 °C for 1 h. The structural phase of orthorhombic structure was also detected in this sample. For the sintered ceramics, a pure tetragonal perovskite phase was observed in the samples sintered between 1025 and 1100 °C. The microstructure of ceramics showed a square or rectangular shape and the average grain size increased with increasing of sintering temperature. The density of the ceramics increased with increasing of sintered temperature up to 1075 °C, were it reached 97.5% of theoretical density and then dropped in value when the sintered temperature further increased. The excellent electrical properties of ε_r at T_c=6600, tanδ at T_c=0.04, P_r (at 40 kV/cm)=19.4 μC/cm² and E_c (at 40 kV/cm)=24.1 kV/cm were obtained in the most dense ceramic. The results indicate that the KNN-LS-BS ceramics are promising lead-free piezoelectric materials.     

Characterization of 0.93Pb(Zn1/3Nb2/3)O3–0.07BaTiO3 ceramics derived from a novel Zn3Nb2O8 B-site precursor

In this work, perovskite relaxor ferroelectric lead zinc niobate–barium titanate (0.93PZN–0.07BT) ceramics were fabricated by using a combination of Zn₃Nb₂O₈ B-site precursor and reactive sintering process. The effects of sintering condition on phase formation, densification, microstructure and dielectric properties of the final products have been investigated using a combination of X-ray diffraction, Archimedes density measurement, scanning electron microscopy and dielectric measurement techniques. It is seen that pure perovskite phase of PZN-BT solid solutions can be achieved in all samples. Density and average grain size values of sintered samples increased with sintering temperatures and dwell time. With appropriate sintering at 1150 °C for 5 h, 0.93PZN–0.07BT ceramics exhibited a peak dielectric constant of 11,497 and dielectric loss of 0.05 at the Curie temperature of 99 °C measured at 1 kHz.     

Preparation and thermal shock resistance of cordierite-spodumene composite ceramics for solar heat transmission pipeline

Cordierite-spodumene composite ceramics with 5, 10, 15 wt% spodumene used for solar heat transmission pipeline were in-situ prepared via pressureless sintering from kaolin, talc, γ-Al₂O₃ and spodumene. Effects of spodumene on densification, mechanical properties, thermal shock resistance, phase composition and microstructure of the composite ceramics were investigated. The results showed that spodumene used as flux material decreased the sintering temperature greatly by 40–80 °C, and improved densification and mechanical properties of the composite ceramics. Especially, sample A3 with 10 wt% spodumene additive sintered at 1380 °C exhibited the best bending strength and thermal shock resistance. The bending strengths of A3 before and after 30 thermal shock cycles (wind cooling from 1100 °C to room temperature) were 102.88 MPa and 96.29 MPa, respectively. XRD analysis indicated that the main phases of the samples before 30 thermal shock cycles were α-cordierite, α-quartz and MgAl₂O₄, and plenty of β-spodumene appeared after thermal shock. SEM micrographs illustrated that the submicron β-spodumene grains generated at the grain boundaries after thermal shock improved the thermal shock resistance. It is believed that the cordierite-spodumene composite ceramics can be a promising candidate material for heat transmission pipeline in the solar thermal power generation.     

Microwave dielectric properties of nanocrystalline TiO2 prepared using spark plasma sintering

TiO₂ bulk ceramics were fabricated by using both spark plasma sintering (SPS) and the conventional sintering method (CSM). Starting materials were ultra fine rutile powders (<50 nm) prepared via the sol–gel process. CSM achieved the relative sintering density of 99.2% at 1300 °C. The grain size of 1300 °C sintered specimen was 6.5 μm. However, the sintering temperature of SPS for the density of 99.1% was as low as 760 °C, where the grain size was only 300 nm. In order to re-oxidize the Ti³⁺ ions due to the reducing atmosphere of the SPS process and the high temperature of the CSM process, the prepared TiO₂ specimens were annealed in an oxygen atmosphere. The dielectric constant (ɛ_r) and quality factor (Q × f) of SPS-TiO₂ re-oxidized specimens in a microwave regime were 112.6 and 26,000, respectively. These properties were comparable to those of 1300 °C sintered CSM specimens (ɛ_r ∼ 101.3, Q × f ∼ 41,600). These microwave dielectric properties of nanocrystalline TiO₂ specimens prepared using SPS were discussed in terms of grain size variation and Ti⁴⁺ reduction.     

Microstructure,ferroelectric and piezoelectric properties of Bi0.5K0.5TiO3-modified BiFeO3–BaTiO3 lead-free ceramics with high Curie temperature

The effects of composition, sintering temperature and dwell time on the microstructure and electrical properties of (0.75 ? x)BiFeO₃–0.25BaTiO₃–xBi_0.5K_0.5TiO₃ + 1 mol% MnO₂ ceramics were studied. The ceramics sintered at 1000 °C for 2 h possess a pure perovskite structure and a morphotropic phase boundary of rhombohedral and pseudocubic phases is formed at x = 0.025. The addition of Bi_0.5K_0.5TiO₃ retards the grain growth and induces two dielectric anomalies at high temperatures (T₁ ～ 450–550 °C and T₂ ～ 700 °C, respectively). After the addition of 2.5 mol% Bi_0.5K_0.5TiO₃, the ferroelectric and piezoelectric properties of the ceramics are improved and very high Curie temperature of 708 °C is obtained. Sintering temperature has an important influence on the microstructure and electrical properties of the ceramics. Critical sintering temperature is 970 °C. For the ceramic with x = 0.025 sintered at/above 970 °C, large grains, good densification, high resistivity and enhanced electrical properties are obtained. The weak dependences of microstructure and electrical properties on dwell time are observed for the ceramic with x = 0.025.     

Two-step sintering assisted consolidation of bulk titania nano-ceramics by spark plasma sintering

This work investigates the feasibility to the fabrication of high density of nano-grained titanium dioxide ceramics by two-step sintering process under spark plasma conditions. First step is carried out by fast-heating-rate sintering in order to obtain an initial high density and a second step is held at a lower temperature by isothermal sintering aiming to increase the density without obvious grain growth. Experiments are conducted to determine the appropriate temperatures for each step. The temperature range between 840 and 850 °C is effective for the first step sintering (T₁) due to its highest densification rate. The isothermal sintering is then carried out at 810–830 °C (T₂) for various hours in order to avoid the abnormal grain growth and improve the density at the same time. TiO₂ bulk ceramics with nano-sized grain were fabricated successfully by combination of spark plasma sintering (SPS) with the two step sintering method (TSS). Titanium dioxide nano-ceramics with >95% theoretical density could be obtained with T₁ and T₂ taken as 850 °C and 830 °C, respectively. The relative grain growth quotient D/D_o for the used starting powder was almost ～1. Further XRD investigations indicated no obvious anatase–rutile transition was found in the prepared nano-crystalline ceramics.     

Structural,dielectric and ferroelectric properties of lead-free Ba0.85Ca0.15Zr0.10Ti0.90O3 ceramics prepared by Plasma Activated Sintering

Lead-free Ba_0.85Ca_0.15Zr_0.10Ti_0.90O₃ (BCZT) ceramics were prepared by Plasma Activated Sintering (PAS). The influence of PAS sintering temperature on the crystalline phase, microstructure, and, dielectric and ferroelectric properties of BCZT ceramics were studied. The phase structure of BCZT ceramics first changed from rhombohedral phase to the coexistence of rhombohedral and tetragonal phases and then to tetragonal phase as the sintering temperature increased. Microstructural characterization of BCZT ceramics indicated that PAS can obtain a compact microstructure at lower temperatures of 1150–1300 °C compared with that from common pressureless sintering. The BCZT ceramics showed different degrees of diffuseness with increased temperature, and the diffuseness exponents C are all approximately on the order of 10⁵ °C. The dielectric and ferroelectric properties of BCZT ceramics were enhanced with increased sintering temperature. BCZT ceramics sintered at 1250 °C exhibited optimum properties of room-temperature ε_r=2863, ε_m=6650, and 2P_r=25.24 μC/cm², resulting from the relatively higher tetragonal phase content of the MPB between tetragonal and rhombohedral phases together with a compact microstructure.     

Microstructure and electrical properties of ZnO–Bi2O3-based varistor ceramics by different sintering processes

The effect of sintering processes, such as open sintering, sintering inside a closed crucible, and sintering within a powder bed, on the microstructure and V–I characteristics of ZnO–Bi₂O₃-based varistor ceramics was investigated at sintering temperatures in the range 1000–1200 °C. The results from the experiments showed that the microstructure and electrical properties of the samples varied according to the sintering method and temperature. Optimal values for the electrical characteristics of the varistor ceramics by different sintering processes were obtained when the sintering was conducted at 1100 °C. At the same sintering temperature, the different processes affected the properties differently. At 1000 °C, the samples sintered within a powdered bed showed better electrical properties than those subjected to the other two processes, while at 1100 or 1200 °C, the samples sintered in an open crucible exhibited the best electrical properties.     

Effect of two-step sintering on the hydrothermal ageing resistance of tetragonal zirconia polycrystals

The effects of two-step sintering (TSS) on the mechanical properties and hydrothermal ageing resistance of yttria-stabilized tetragonal zirconia polycrystals (Y-TZP) were investigated. In TSS, the first step involved heating the samples up to 1400 °C at a heating rate of 10 °C/min and holding the samples at this temperature for 1 min. The second step involved sintering by cooling the samples down to 1200 °C and holding the samples at this temperature for various holding times (t) ranging from 0 to 30 h before cooling to room temperature. Moreover, TSS promoted densification with increasing holding time without sacrificing the mechanical properties of the sintered body and causing abnormal grain growth. The average grain size was found not to be affected by the long holding times, and the final microstructure composed of a uniformly distributed tetragonal grain having sizes ranging from 0.24 to 0.26 µm. The beneficial effect of TSS in suppressing the hydrothermal ageing of Y-TZP has been revealed in the present work. In particular, samples sintered at t=20 and 30 h exhibited excellent resistance to low-temperature degradation when exposed to superheated steam at 180 °C, attributed mainly to the enhance densification of the sintered bodies.     

Preparation and microwave dielectric properties of cristobalite ceramics

Dense SiO₂ ceramics with cristobalite phase were prepared by the solid state sintering route, and the microwave dielectric properties were evaluated. The dielectric constant (?_r) and temperature coefficient of resonant frequency (τ_f) of the pure cristobalite ceramics showed little dependence on the sintering temperature. While, the Qf value increased significantly with increasing the sintering temperature, and it was due to the increasing grain size. The optimized microwave dielectric properties with very low ?_r of 3.81, high Qf value of 80,400 GHz and low τ_f of ?16.1 ppm/°C were obtained for the cristobalite ceramics sintered at 1650 °C for 3 h. It was indicated that cristobalite ceramic was a promising candidate as a low-dielectric-constant microwave material for applications in microwave substrates.     

Preparation of c-axis textured SiC ceramics by a strong magnetic field of 6 T assisted gel-casting process

C-axis textured SiC ceramics were prepared by a strong magnetic field of 6 T assisted gel-casting and subsequent pressureless sintering. The optimal suspension parameters for gel-casting were determined by analyzing the influences of pH value and dispersant content on the stability and dispersibility of suspensions. The effect of sintering conditions on the texture development and properties of SiC ceramics was discussed. It was found that the increasing sintering temperature or holding time promoted the densification process of SiC ceramics. The c-axis of SiC grain was aligned parallel to the magnetic field by applying a strong magnetic field of 6 T. The degree of texture of SiC ceramics showed a slightly increasing trend with the increase of sintering temperature or holding time. When the samples were sintered at 1950 °C for 4 h or 6 h, the large elongated grains were formed in the samples, leading to the extremely evident anisotropic microstructure on different planes. Textured SiC ceramics exhibited the anisotropic bending strength.