Effects of pore structure on thermal conductivity and strength of alumina porous ceramics using carbon black as pore-forming agent

In the present work, carbon black (CB) works as a pore-forming agent in the preparation of alumina porous ceramics. The pore structures (i.e. mean pore size, pore size distribution and various pores size proportions) were characterized by means of Micro-image Analysis and Process System (MIAPS) software and mercury intrusion porosimetry. Then their correlation and thermal conductivity as well as strength were determined using grey relation theory. The results showed that the porosity and mean pore size increased against the amount of CB, whereas the thermal conductivity, cold crushing strength and cold modulus of rupture reduced. The <2 μm pores were helpful for enhancing the strength and decreasing the thermal conductivity whereas the >14 μm pores had the opposite effects.     

Thermal conductivity of porous alumina ceramics prepared using starch as a pore-forming agent

The thermal conductivity of porous alumina ceramics prepared using different types of starch (potato, wheat, corn, and rice starch) as pore-forming agents is investigated from room temperature up to 500 °C. The temperature dependence measured for alumina ceramics of different porosity (in the range 6–47%) is fitted with second-order polynomials and 1/T-type relations, and compared to available literature data for dense alumina. It is found that the porosity dependence of the relative thermal conductivity k_r = k/k₀ is well described by a modified exponential relation of the form k_r = exp(?1.5?/(1 ? ?)), where ? is the porosity. This finding is in agreement with other literature data and seems to indicate a common feature of all porous materials with microstructures resulting from fugitive pore-forming agents.     

New multifunctional porous Yb2SiO5 ceramics prepared by freeze casting

New porous Yb₂SiO₅ ceramics were prepared by a water-based freeze casting technique using synthesized Yb₂SiO₅ powders. The prepared porous Yb₂SiO₅ ceramics exhibit multiple pore structures, including lamellar channel pores and small pores, in its skeleton. The effects of the solid content and sintering temperature on the pore structure, porosity, dielectric and mechanical properties of the porous Yb₂SiO₅ ceramics were investigated. The sample with 20 vol% solids content prepared at 1550 °C exhibited an ultra-low linear shrinkage (i.e. 4.5%), a high porosity (i.e. 79.1%), a high compressive strength (i.e. 4.9 MPa), a low dielectric constant (i.e. 2.38) and low thermal conductivity (i.e. 0.168 W/(m K)). These results indicate that porous Yb₂SiO₅ ceramics are good candidates for ultra-high temperature broadband radome structures and thermal insulator materials.     

Investigating the effect of SPRM on mechanical strength and thermal conductivity of highly porous alumina ceramics

For recycling waste refractory materials in metallurgical industry, porous alumina ceramics were prepared via pore forming agent method from α-Al₂O₃ powder and slide plate renewable material. Effects of slide plate renewable material (SPRM) on densification, mechanical strength, thermal conductivity, phase composition and microstructure of the porous alumina ceramics were investigated. The results showed that SPRM effectively affected physical and thermal properties of the porous ceramics. With the increase of SPRM, apparent porosity of the ceramic materials firstly increased and then decreased, which brought an opposite change for the bulk density and thermal conductivity values, whereas the bending strength didn’t decrease obviously. The optimum sample A2 with 50 wt% SPRM introducing sintered at 1500 °C obtained the best properties. The water absorption, apparent porosity, bulk density, bending strength and thermal conductivity of the sample were 31.7%, 62.8%, 1.71 g/cm³, 47.1 ± 3.7 MPa and 1.73 W/m K, respectively. XRD analysis indicated that a small quantity of silicon carbide and graphite in SPRM have been oxidized to SiO₂ during the firing process, resulting in rising the porous microstructures. SEM micrographs illustrated that rod-like mullite grains combined with plate-like corundum grains to endow the samples with high bending strength. This study was intended to confirm the preparation of porous alumina ceramics with high porosity, good mechanical properties and low thermal conductivity by using SPRM as pore forming additive.     

Low cost foam-gelcasting preparation and characterization of porous magnesium aluminate spinel (MgAl2O4) ceramics

Porous MgAl₂O₄ ceramics were prepared via a low cost foam-gelcasting route using MgAl₂O₄ powders as the main raw material, ammonium polyacrylate as a dispersant, a small amount of modified carboxymethyl cellulose as a gelling agent, and TH-IV polymer as a foaming agent. The effects of additive's content, solid loading and gelling temperature on slurry's rheological behavior were investigated, and microstructures and properties of as-prepared porous MgAl₂O₄ ceramics examined. Based on the results, the roles played by the foaming agent in the cases of porosity, pore structure, pore size, mechanical properties and thermal conductivity were clarified. Porosity and pore sizes of as-prepared porous MgAl₂O₄ ceramics increased with increasing the foaming agent from 0.05 to 0.6 vol%. Porous MgAl₂O₄ ceramics with porosity of 75.1% and average pore size of 266 µm exhibited a compressive strength as high as 12.5±0.8 MPa and thermal conductivity as low as 0.24 W/(m K) (at 473 K).     

Structure and mechanical properties of porous silicon oxycarbide ceramics derived from silicone resin with different filler content

Porous silicon oxycarbide ceramics were obtained through pyrolysis of a new silicone resin filled with its pyrolyzed SiOC powders via a simple self-blowing process. The effects of filler content on the porosity, compressive strength and microstructure of the porous ceramics were investigated. The porosity (total and open) increased firstly and then decreased with the filler content increasing. It was possible to control the total and open porosity of porous ceramics within a range of 66.1–88.2% and 42.7–72.5% respectively, by adjusting the filler content from 0 vol% to 30 vol% while keeping the heating rate fixed at 0.5 °C/min. The compressive strength decreased firstly and then increased with the increasing filler content, and the average compressive strength of the porous ceramics was in the range of 1.1–3.4 MPa. Micrographs indicated that the porous ceramics with the filler content less than 20 vol% had a well-defined open-cell and regular pore structure.     

Preparation and characterization of porous alumina ceramics through starch consolidation casting technique

This work aims at studying the influence of thermal treatment on the microstructure, resistivity and technological properties of porous alumina ceramics prepared via starch consolidation casting (SCC) technique. Colloidal suspensions were prepared with three different contents of alumina solid loading (55, 60 and 65 mass%) and corn starch (3, 8 and 13 mass%). The sintered samples at 1400, 1500, 1600 and 1700 °C, show open porosity between 46 and 64%, depending on the starch content in the precursor suspensions and sintering temperature. The pore structures were analyzed by SEM. The effect of corn starch content on the apparent porosity, pore size distribution, linear shrinkage and electrical resistivity as well as cold crushing strength of the sintered porous alumina ceramics was also measured. These porous alumina ceramics are promising porous ceramic materials for using in a wide range of thermal, electrical and bioceramics applications as well as filters/membranes and gas burners, due to their excellent combination properties.     

Preparation and properties of mullite-bonded porous fibrous mullite ceramics by an epoxy resin gel-casting process

Porous fibrous mullite ceramics with a narrow range of pore size distribution have been successfully prepared utilizing a near net-shape epoxy resin gel-casting process by using mullite fibers, Al₂O₃ and SiC as raw materials. The effects of sintering temperatures, different amounts of fibers and Y₂O₃ additive on the phase compositions, linear shrinkage, apparent porosity, bulk density, microstructure, compressive strength and thermal conductivity were investigated. The results indicated that mullite-bonded among fibers were formed in the porous fibrous mullite ceramics with a bird nest pore structure. After determining the sintering temperatures and the amount of fibers, the tailored porous fibrous mullite ceramics had a low linear shrinkage (1.36–3.08%), a high apparent porosity (61.1–71.7%), a relatively high compressive strength (4.4–7.6 MPa), a low thermal conductivity (0.378–0.467 W/m K) and a narrow range of pore size distribution (around 5 µm). The excellent properties will enable the porous ceramics as a promising candidate for the applications of hot gas filters, thermal insulation materials at high temperatures.     

Foam-gelcasting preparation,microstructure and thermal insulation performance of porous diatomite ceramics with hierarchical pore structures

Hierarchically pore-structured porous diatomite ceramics containing 82.9∼84.5% porosity were successfully prepared for the first time via foam-gelcasting using diatomite powder as the main raw material. Sizes of mesopores derived from the raw material and macropores formed mainly from foaming were 0.02∼0.1 μm and 109.7∼130.5 μm, respectively. The effect of sintering temperature, additive content and solid loading of slurry on pore size and distribution, and mechanical and thermal properties of as-prepared porous ceramics were investigated. Compressive strength of as-prepared porous ceramics increased with sintering temperature, and the one containing 82.9% porosity showed the highest compressive strength of 2.1 ± 0.14 MPa. In addition, the one containing 84.5% porosity and having compressive strength of 1.1 ± 0.07 MPa showed the lowest thermal conductivity of 0.097 ± 0.001 W/(m·K) at a test temperature of 200 ̊C, suggesting that as-prepared porous ceramics could be potentially used as good thermal insulation materials.     

Effects of mono-dispersed PMMA micro-balls as pore-forming agent on the properties of porous YSZ ceramics

Porous yttria-stabilized zirconia (YSZ) ceramics were successfully fabricated by the dry pressing method with different size (1.8–20 μm) and amount (2–60 vol.%) of mono-dispersed poly methyl methacrylate (PMMA) micro-balls. Different PMMA additions with different size and amount were investigated to achieve optimal thermal and mechanical properties. With increases of the amount of PMMA, the porosity of porous YSZ ceramics ranges from 7.29% to 51.6%, the flexural strength increases firstly and then decreases, and the thermal conductivity decreases continuously. With decreases of the diameter of PMMA micro-balls, the mean pore size and thermal conductivity of porous YSZ ceramics decrease, and the flexural strength of porous YSZ ceramics with same porosity increases firstly and then decreases. The porous YSZ ceramics with a higher porosity (18.44 ± 1.24%), the highest flexural strength (106.88 ± 3.2179 MPa) and low thermal conductivity (1.105 ± 0.15 W/m K) can be obtained when the particle diameter and the amount of PMMA are 5 μm and 20 vol.%, respectively.     

Processing and properties of low cost macroporous alumina ceramics with tailored porosity and pore size fabricated using rice husk and sucrose

The present study demonstrates a cost effective way to fabricate porous ceramics with tailored microstructures using rice husk (RH) of various range of particle sizes as a pore former and sucrose as a binder as well as a pore former. Sample microstructures reveal randomly oriented elongated coarse pores and fine pores (avg. size 4 μm) created due to burnout of RH and sucrose, respectively. Porous alumina ceramics with 20–66 vol% porosity and 50–516 μm avg. pore size (length), having isolated and/or interconnected pores, were fabricated using this process. Mechanical properties of the porous samples were determined as a function of porosity and pore microstructure. The obtained porous ceramics exhibited flexural strength of 207.6–22.3 MPa, compressive strength of 180–9.18 MPa, elastic modulus of 250–18 GPa and hardness of 149–18 HRD. Suggested application area includes thermal, filtration, gas purging etc.     

Improvement on characteristics of porous alumina from platelets using a TEOS treatment

A porous alumina body was synthesized from anisotropic alumina particles, namely platelets. When green compacts, which had been uniaxially pressed at 1 MPa, were heated at 1200 and 1500 °C for 1 h, the average porosity of the resulting alumina bodies was 75.5 and 71.0%, respectively. The thermal conductivity of the porous alumina fabricated at 1400 °C for 1 h with 72.3% in porosity was 0.8 W m^?1 K^?1. In an attempt to increase the compressive strength of the porous alumina bodies, TEOS (tetraethyl orthosilicate) solution treatment was carried out, followed by reheating to 1400 °C for 1 h. The compressive strength of the porous alumina body increased from 3.8 MPa (without TEOS solution treatment) to 10.2 MPa (with three rounds of TEOS treatment), with the porosity decreasing to 65.5% and the thermal conductivity increasing to1.2 W m^?1 K^?1.     

Preparation and properties of porous alumina ceramics with oriented cylindrical pores produced by an extrusion method

Porous alumina ceramics with unidirectionally-oriented pores were prepared by extrusion. Carbon fibers of 14 μm diameter and 600 μm length to be used as the pore-forming agent were kneaded with alumina, binder and dispersing agent. The resulting paste was extruded, dried at 110 °C, degreased at 1000 °C and fired at 1600 °C for 2 h. SEM showed a microstructure of dispersed highly oriented pores in a dense alumina matrix. The pore area in the cross section was 25.3% with about 1700 pores/mm². The pore size distribution of the fired body measured by Hg porosimetry showed a sharp peak corresponding to the diameter of the burnt-out carbon fibers. The resulting porous alumina ceramics with 38% total porosity showed a fracture strength of 171 MPa and a Young's modulus of 132 GPa. This strength is significantly higher than the reported value for other porous alumina ceramics even though the present pore size is much larger.     

Preparation of porous Y2SiO5 ceramics with relatively high compressive strength and ultra-low thermal conductivity by a TBA-based gel-casting method

Porous Y₂SiO₅ ceramics with relative high compressive strength (as high as 24.45 MPa) and ultra-low thermal conductivity (～0.08 W/m K) were successfully fabricated by a tert-butyl alcohol based gel-casting method. The formation mechanism of the 3D interconnected pores and the properties of the green body are discussed. The porosity, pore size, compressive strength and thermal conductivity could be controlled by varying the initial solid loading and the sintering temperature. When regulating the initial solid loading (from 20 to 50 wt%) and sintering temperature (from 1200 to 1500 °C), the porosity can be controlled between 47.74% and 73.93%, and the compressive strength and the thermal conductivity of porous Y₂SiO₅ ceramics varied from 3.34 to 24.45 MPa and from 0.08 to 0.55 W/m K, respectively. It should be noted that the porous Y₂SiO₅ ceramics with 30 wt% solid loading and sintering at 1400 °C had an open porosity of 61.80%, a pore size of 2.24 μm, a low room-temperature thermal conductivity of 0.17 W/m K and a relatively high compressive strength of 13.91 MPa, which make this porous Y₂SiO₅ ceramics suitable for applications in high-temperature thermal insulators.     

Microstructure and properties of lightweight fibrous porous mullite ceramics prepared by vacuum squeeze moulding technique

A novel fibrous porous mullite network with a quasi-layered microstructure was produced by a simple vacuum squeeze moulding technique. The effects of organic binder content, inorganic binder and adsorbent on the microstructure and the room-temperature thermal and mechanical properties of fibrous porous mullite ceramics were systematically investigated. An anisotropy microstructure without agglomeration and layering was achieved. The fibrous porous mullite ceramics reported in this study exhibited low density (0.40 g/cm³), low thermal conductivity (~0.095 W/(m K)), and high compressive strength (~2.1 MPa in the x/y direction). This study reports an optimal processing method for the production of fibrous porous ceramics, which have the potential for use as high-temperature thermal insulation material.     

Investigating the effect of porosity level and pore former type on the mechanical and corrosion resistance properties of agro-waste shaped porous alumina ceramics

The strength integrity and chemical stability of porous alumina ceramics operating under extreme service conditions are of major importance in understanding their service behavior if they are to stand the test of time. In the present study, the effect of porosity and different pore former type on the mechanical strength and corrosion resistance properties of porous alumina ceramics have been studied. Given the potential of agricultural wastes as pore-forming agents (PFAs), a series of porous alumina ceramics (Al₂O₃-xPFA; x=5, 10, 15 and 20 wt%) were successfully prepared from rice husk (RH) and sugarcane bagasse (SCB) through the powder metallurgy technique. Experimental results showed that the porosity (44–67%) and the pore size (70–178 µm) of porous alumina samples maintained a linear relationship with the PFA loading. Comprehensive mechanical strength characterization of the porous alumina samples was conducted not just as a function of porosity but also as a function of the different PFA type used. Overall, the mechanical properties showed an inverse relationship with the porosity as the developed porous alumina samples exhibited tensile and compressive strengths of 20.4–1.5 MPa and 179.5–10.9 MPa respectively. Moreover, higher strengths were observed in the SCB shaped samples up to the 15 wt% PFA mark, while beyond this point, the silica peak observed in the XRD pattern of the RH shaped samples favored their relatively high strength. The corrosion resistance characterization of the porous alumina samples in hot 10 wt% NaOH and 20 wt% H₂SO₄ solutions was also investigated by considering sample formulations with 5–15 wt% PFA addition. With increasing porosity, the mass loss range in RH and SCB shaped samples after corrosion in NaOH solution for 8 h were 1.25–3.6% and 0.44–2.9% respectively; on the other hand, after corrosion in H₂SO₄ solution for 8 h, the mass loss range in RH and SCB shaped samples were 0.62–1.5% and 0.68–3.3% respectively.     

Effects of inert filler addition on the structure and properties of porous SiOC ceramics derived from silicone resin

Porous SiOC ceramics were obtained from a new self-blowing precursor silicone resin DC217, by pyrolysis at 1200 °C in argon. Silicon carbide powders were incorporated into the silicone resin as inert fillers. The effects of the mean particle size of SiC fillers on the porosity, compressive strength and microstructure of the porous ceramics were investigated. With the mean particle size of SiC powders increasing from 5 μm to 10 μm, the porosity (total and open) of the porous ceramic increased and the compressive strength decreased. However, the porosity, compressive strength and cell morphology of the porous ceramics showed no evident changes when the mean particle size of fillers increased from 10 μm to 15 μm. Micrographs indicated that, when the mean particle size of fillers exceeded 5 μm, the porous ceramics could have a well-defined and regular pore structure. Furthermore, comparing with the porous ceramics which fabricated under the same condition with the SiOC powders as fillers, the cell morphology was similar. But the compressive strength and the oxidation resistance of the porous ceramics with SiC powders as fillers were much better.     

Fabrication and properties of thermal insulating material using hollow glass microspheres bonded by aluminum–chrome–phosphate and tetraethyl orthosilicate

Thermal insulation material made by hollow glass microspheres (HGM) with different content of aluminum–chrome–phosphate solution (ACP) and tetraethyl orthosilicate (TEOS) as binders was formed, dried and sintered at 250 °C, 450 °C or 650 °C for 2 h. Properties such as density, compressive strength, thermal conductivity and microstructure of the specimens were determined. It is found that TEOS improved the distribution of ACP and increased the compressive strength of the specimens. HGM bonded by appropriate amount of ACP and TEOS achieved preferable value of density, compressive strength and thermal conductivity which were significant for thermal insulation materials. The compressive strength of specimens sintered at 450 °C and 650 °C was higher than that of the specimens sintered at 250 °C.     

Preparation of calcium hexaluminate porous ceramics by gel-casting method with polymethyl methacrylate as pore-forming agent

Calcium hexaluminate (CA₆) porous ceramics were prepared by gel-casting method, with α-Al₂O₃ and CaCO₃ as raw materials and polymethyl methacrylate (PMMA) microspheres as pore-forming agent. The effects of the amount of pore-forming agent PMMA microspheres on the phase composition, bulk density, apparent porosity, flexural strength, microstructure, thermal shock stability and thermal conductivity of CA₆ porous ceramics were systematically studied. The pores of CA₆ porous ceramics are mainly formed by the burning loss of PMMA microspheres and the decomposition of organic matter. Adding an appropriate amount of PMMA microspheres as pore-forming agent has a positive effect on the thermal shock stability of CA₆ porous ceramics. When the amount of pore-forming agent is 15 wt%, the volume density of CA₆ porous ceramics is 1.33 g/cm³, the porosity is 63%, the flexural strength is 13.9 MPa, the thermal shock times can reach 9 times, and the thermal conductivity is 0.293 W/(m·K), which can meet the application in refractory, ceramics or high temperature cement industries.     

Fabrication and properties of mullite fiber matrix porous ceramics by a TBA-based gel-casting process

A bird nest-like structure was designed by using the mullite fiber as the matrix and SiO₂ as the high temperature binder. This special material was successfully prepared by a TBA-based gel-casting process. The randomly arranged fiber laps bonded by SiO₂ binder was the most important structure characteristic of this porous material. The effect of sintering temperature on the properties, i.e. porosity, bulk density, linear shrinkage, compressive strength, thermal conductivity and the microstructure was studied. The composite exhibited significant pseudoductility. The fracture mechanism of this composite under compression was discussed. The results indicated that the sintering temperature ranging from 1500 to 1600 °C was suitable for yielding mullite fiber matrix porous ceramics which had a low thermal conductivity (0.19–0.22 W/m K), a relatively high compressive strength (3–13 MPa) and a high resilience (66–70%) for applications in the thermal insulators and high-temperature elastic seal field.