Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Zirconia ceramic is a significant structural material, but its use under some extreme circumstances is limited by its mechanical properties. In this work, SiC particles (SiCp) were added into alumina toughened zirconia ceramics to prepare ZrO₂–Al₂O₃-SiCp ceramics with high performance by using oscillatory pressure sintering (OPS). Results showed that the best OPS temperature of 1600 °C was obtained, and the optimal SiCp particle size and content were 200 nm and 10 vol% respectively. Under these conditions, the specimen exhibited higher mechanical properties including Vickers hardness of 15.43 GPa, bending strength of 1162 MPa and fracture toughness of 6.36 MPa m^1/2. Moreover, it was found that the atomic matching between ZrO₂/SiCp, Al₂O₃/SiCp, and ZrO₂/Al₂O₃ was much higher, showing the coherent interface relationship. Therefore, it was favorable for enhanced mechanical properties of as-prepared ZrO₂–Al₂O₃-SiCp ceramics.     

Effect of Al2O3 particles on mechanical and tribological properties of Al–Mg dual-matrix nanocomposites

This article aims to manufacture homogenous dual-matrix Al–Mg/Al₂O₃ nanocomposite from their raw materials and give insight into the correlation between powder morphology, crystallite structure and their mechanical and tribological properties. Al–Mg dual-matrix reinforced with micro/nano Al₂O₃ particles was manufactured by a novel double high-energy ball milling process followed by a cold consolidation and sintering. Microstructure and phase composition of the prepared samples were characterized using FE-SEM, EDS and XRD inspections. Mechanical and wear properties were characterized using compression and sliding wear tests. The results showed that a milling of Mg with Al₂O₃ particles in an initial step before mixing with Al has the beneficial of well dispersion of Al₂O₃ nanoparticles in Al–Mg dual matrix. The Al–Mg dual matrix reinforced with nano-size Al₂O₃ showed 3.29-times smaller crystallite size than pure Al. Moreover, the hardness and compressive strength are enhanced by adding nano-size Al₂O₃ with Al–Mg dual matrix composite while the ductility is maintained relatively high. Additionally, the wear rate of this composite was reduced by a factor of 2.7 compared to pure Al. The reduced crystallite size, the dispersion of Al₂O₃ nanoparticles and the formation of (Al–Mg)_ss were the main improvement factors for mechanical and wear properties.     

Optical and mechanical properties of amorphous bulk and eutectic ceramics in the HfO2–Al2O3–Y2O3 system

Bulk glasses containing HfO₂ nano-crystallites of 20–50 nm were prepared by hot-pressing of HfO₂–Al₂O₃–Y₂O₃ glass microspheres at 915 °C for 10 min. By annealing at temperatures below 1200 °C, the bulk glasses were converted into transparent glass-ceramics with HfO₂ nano-crystallites of 100–200 nm, which showed the maximum transmittance of ～70% in the infrared region. An increase of annealing temperature (>1300 °C) resulted in opaque YAG/HfO₂/Al₂O₃ eutectic ceramics. The eutectic ceramics contained fine Al₂O₃ crystallites and showed a high hardness of 19.8 GPa. The fracture toughness of the eutectic ceramics increased with increasing annealing temperature, and reached the maximum of 4.0 MPa m^1/2.     

Effect of Y2O3 on the physical properties and biocompatibility of β–SiAlON ceramics

To investigate the effects of Y₂O₃ on the physical properties and biocompatibility of β–SiAlON ceramics, β–SiAlON ceramics were prepared with Al, Si, and α–Al₂O₃ powders using a direct nitriding technique. As a sintering additive, Y₂O₃ helps lower the sintering temperature and forms β–SiAlON ceramics. In this study, the physical and biological properties of the prepared ceramics were investigated to evaluate their use as bone-repairing material. Experiments revealed that the main crystal composition of the sample was Si₄Al₂O₂N₆, containing small amount of additional phases Y₃Al₅O₁₂ with increasing content of Y₂O₃. The porosity and compressive strength initially decrease and then increase to their initial values, whereas the bulk density exhibits the opposite trend with an increased proportion of Y₂O₃. The proliferation of osteoblastic and angiogenic cells demonstrates that β–SiAlON and Y₃Al₅O₁₂ have good biocompatibility; however, the sample porosity has a slight effect on the cell proliferation rate. This implies that in human tissues, bone-repairing speed can be adjusted by modifying the sample porosity or material surface roughness. Therefore, Y₂O₃ can be added to β–SiAlON ceramics to regulate their microstructure, physical properties, and biological properties for tissue engineering applications.     

Effects of Al2O3–Y2O3/Yb2O3 additives on microstructures and mechanical properties of silicon nitride ceramics prepared by hot-pressing sintering

Silicon nitride (Si₃N₄) ceramics doped with two different sintering additive systems (Al₂O₃–Y₂O₃ and Al₂O₃–Yb₂O₃) were prepared by hot-pressing sintering at 1800℃ for 2 h and 30 MPa. The microstructures, nano-indentation test, and mechanical properties of the as-prepared Si₃N₄ ceramics were systematically investigated. The X-ray diffraction analyses of the as-prepared Si₃N₄ ceramics doped with the two sintering additives showed a large number of phase transformations of α-Si₃N₄ to β-Si₃N₄. Grain size distributions and aspect ratios as well as their effects on mechanical properties are presented in this study. The specimen doped with the Al₂O₃–Yb₂O₃ sintering additive has a larger aspect ratio and higher fracture toughness, while the Vickers hardness is relatively lower. It can be seen from the nano-indentation tests that the stronger the elastic deformation ability of the specimens, the higher the fracture toughness. At the same time, the mechanical properties are greatly enhanced by specific interlocking microstructures formed by the high aspect ratio β-Si₃N₄ grains. In addition, the density, relative density, and flexural strength of the as-prepared Si₃N₄ ceramics doped with Al₂O₃–Y₂O₃ were 3.25 g/cm³, 99.9%, and 1053 ± 53 MPa, respectively. When Al₂O₃–Yb₂O₃ additives were introduced, the above properties reached 3.33 g/cm³, 99.9%, and 1150 ± 106 MPa, respectively. It reveals that microstructure control and mechanical property optimization for Si₃N₄ ceramics are feasible by tailoring sintering additives.     

Microwave hybrid sintering of Al2O3 and Al2O3–ZrO2 composites,and effects of ZrO2 crystal structure on mechanical properties,thermal properties,and sintering kinetics

Structural ceramics such as Al₂O₃ and Al₂O₃–ZrO₂ composites are widely used in harsh environment applications. The conventional sintering process for fabrication of these ceramics is time-consuming method that requires large amount of energy. Microwave sintering is a novel way to resolve this problem. However, to date, very limited research has been carried out to study the effects of different ZrO₂ crystal structures on Al₂O₃–ZrO₂ composites, especially on the sintering kinetics, when fabricated by microwave sintering.The microwave hybrid sintering of Al₂O₃ and Al₂O₃–ZrO₂ composites was performed in this study. Tetragonal zirconia and cubic zirconia were used as two different reinforcements for an α–alumina matrix, and the mechanical and thermal properties were studied. It was found that Al₂O₃ experienced a remarkable increase in fracture toughness of up to 42% when t-ZrO₂ was added. Al₂O₃–c-ZrO₂ also showed increased fracture toughness. The sintering kinetics were also thoroughly investigated, and the average activation energy values for the intermediate stage of sintering were estimated to be 246 ± 11 kJ/mol for pure Al₂O₃, 319 ± 71 kJ/mol for Al₂O₃–c-ZrO₂, and 342 ± 77 kJ/mol for Al₂O₃–t-ZrO₂. These values indicated that the activation energy was increased by the addition of either type of ZrO₂, with the highest value shown by Al₂O₃–t-ZrO₂.     

Effect of solid loading on properties of Y2O3–Al2O3–Nd2O3 powder mixtures obtained by planetary ball milling and ceramics based on them

The effect of the solid loading (41–50 wt%) of the slurry on granulometric composition and physico-chemical characteristics of Y₂O₃–Al₂O₃–Nd₂O₃ powder mixtures obtained by planetary ball milling has been studied for the first time. It was shown that the particle size distribution of powder, its Zeta potential, and specific surface area depend on the solid loading of the milled slurry and, consequently, on the interparticle distance during milling. The interparticle distance decreases from 200 nm to 142 nm with an increase of solid loading in the range of 41–50 wt%. It was shown that for the solid loading of 47 wt%, the convergence of particles to a distance comparable to their median diameter promotes subsequent clustering of particles. This facilitates the sintering of highly-homogenous ceramics. It was found that solid loadings in the 46–50 wt% range is useful for obtaining high-quality Nd:YAG transparent ceramics. The lowest optical losses optical losses of 1 × 10^?3 cm^?1 and the highest in-line transmittance of 84.1%@1064 nm were obtained for 1 at.% Nd:YAG transparent ceramics (22 × 3 × 4 mm³) prepared from slurries with 47 wt% solid loading (taking all other ball milling parameters fixed). If the interparticle distance in the powder is higher (solid loading of 41 wt%) than the median particle diameter, the ceramics are characterized by significant residual porosity due to the survival of large particles (insufficient milling).     

Effect of CaO doping on the properties and crystallization behavior of Y2O3–Al2O3–SiO2 glass

Nowadays, Y₂O₃–Al₂O₃–SiO₂ (YAS) glass joining is considered to be a promising scheme for nuclear-grade continuous silicon carbide (SiC) fiber reinforced SiC matrix composites (SiC/SiC). CaO has great potential for nuclear applications since it has low reactivity and low decay rate under nuclear irradiation. In this paper, the effect of CaO doping on the structure, thermophysical properties, and crystallization behavior of YAS glass was systematically studied. As the CaO doping content increased, the number of bridge oxygens and the viscosity at high temperatures reduced gradually. After heat treatment at 1400 °C, the main phases in YAS glass were β-Y₂Si₂O₇, mullite, and SiO₂ (coexistence of crystalline and glass phases), while that with 3.0% CaO doping turned into a single glassy phase under the same treatment conditions. Moreover, a structural model and the modification mechanism were proposed, which provided a theoretical basis for the subsequent component design and optimization.     

Effect of yttria substitution on structure,optical and mechanical properties of (Gd,Y)2O3–MgO nanocomposite ceramics

A citrate-nitrate combustion method was applied to synthesize fine composite Gd_2-xY_xO₃-MgO (x = 0, 0.02, 0.2, 0.3, 0.4, 0.6) nanopowders. Y₂O₃ substitution inhibited Gd₂O₃ phase transition from cubic structure to monoclinic structure during sintering, thereby stabilizing its cubic structure to room temperature. This approach led to nanocomposite ceramics with a grain size of about 190 nm and increased the transmittance to 85% over the 3–5 μm wavelength range when x = 0.3. However, the addition of Y₂O₃ weakened the mechanic properties of the nanocomposite ceramics.     

Sintering,microstructure and mechanical properties of Al2O3–Y2O3–ZrO2 (AYZ) eutectic composition ceramic microcomposites

We report on how the mechanical properties of sintered ceramics (i.e., a random mixture of equiaxed grains) with the Al₂O₃–Y₂O₃–ZrO₂ eutectic composition compare with those of rapidly or directionally solidified Al₂O₃–Y₂O₃–ZrO₂ eutectic melts. Ceramic microcomposites with the Al₂O₃–Y₂O₃–ZrO₂ eutectic composition were fabricated by sintering in air at 1400–1500 °C, or hot pressing at 1300–1400 °C. Fully dense, three phase composites of Al₂O₃, Y₂O₃-stabilized ZrO₂ and YAG with grain sizes ranging from 0.4 to 0.8 μm were obtained. The grain size of the three phases was controlled by the size of the initial powders. Annealing at 1500 °C for 96 h resulted in grain sizes of 0.5–1.8 μm. The finest scale microcomposite had a maximum hardness of 19 GPa and a four-point bend strength of 282 MPa. The fracture toughness, as determined by Vickers indentation and indented four-point bending methods, ranged from 2.3 to 4.7 MPa m^1/2. Although strengths and fracture toughnesses are lower than some directionally or rapidly solidified eutectic composites, the intergranular fracture patterns in the sintered ceramic suggest that ceramic microcomposites have the potential to be tailored to yield stronger, tougher composites that may be comparable with melt solidified eutectic composites.     

Effect of TiO2 on crystallization and mechanical properties of MgO–Al2O3–SiO2 glasses containing P2O5

MgO–Al₂O₃–SiO₂ glass-ceramics have been widely used in military, industrial, and construction applications. The nucleating agent is one of the most important factors in the production of glass-ceramics as it can control the crystallization temperature or the grain size. In this study, we investigated the effect of replacing P₂O₅ with different amounts of TiO₂ on the crystallization, structure, and mechanical properties of an MgO–Al₂O₃–SiO₂ system. The crystallization and microstructure were investigated by differential scanning calorimetry, Raman spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The mechanical properties were investigated by measuring the Vickers hardness, Young's modulus, and fracture toughness. The results showed that adding TiO₂ favored the precipitation of fine grains and significantly increased the Vickers hardness, Young's modulus, and fracture toughness of the glasses. Introducing an appropriate amount of TiO₂ can make a glass structure more compact, promote crystallization, and improve the mechanical properties of MgO–Al₂O₃–SiO₂ glass-ceramics.     

Preparation and study of the mechanical and optical properties of infrared transparent Y2O3–MgO composite ceramics

In this study, fine Y₂O₃–MgO composite nanopowders were synthesized via the sol–gel method. Dense Y₂O₃–MgO composite ceramics were fabricated by pre-sintering the green body in air at different temperatures for 1 h and then subjecting the sintered bodies to hot isostatic pressing at 1300°C for 1 h. The effects of pre-sintering temperature on the microstructural, mechanical, and optical properties of the resulting ceramics were studied. The average grain size of the ceramics was increased, whereas their hardness and fracture toughness were decreased with increasing pre-sintering temperature. A maximum fracture toughness of 1.42 MPa·m^1/2 and Vickers hardness of 10.4 GPa were obtained. The average flexural strength of the ceramics was 411 MPa at room temperature and reached 361 MPa at 600°C. A transmittance of 84% in the 3–5 µm region was obtained when the composite ceramics were sintered at 1400°C. Moreover, a transmittance of 76% in the 3–5 µm region was obtained at 500°C.     

Effect of ZnO on the structural,physio-mechanical properties and thermal shock resistance of Li2O–Al2O3–SiO2 glass-ceramics

The composition of lithium aluminosilicate (LAS) with different zinc oxide-magnesium oxide (ZnO–MgO) contents that ranged from 0 to 1.45 wt percent (wt%) was investigated to determine the thermal shock resistance properties of the glass-ceramics. The LAS glasses were melted in an alumina crucible at 1550 °C for 5 h, and the green compact samples were then heat-treated at 1100 °C for 3.5 h. The presence of zinc oxide (ZnO) in the compositions did not change the major crystal phase of β-spodumene. However, the addition of ZnO shifted the pronounced peak to a lower angle and increased the percentage of crystallinity from 55% to 59%. Additionally, the function of ZnO in LAS glass-ceramics as the network modifier was confirmed through Fourier Transform Infrared Spectroscopy (FTIR) analysis. The physio-mechanical properties were improved when 1.45 wt% ZnO was added to the LAS glass-ceramics. The results showed increased density (2.42 g/cm³), low porosity (0.85%), high flexural strength (125.23 MPa), and low coefficient of thermal expansion (25–800 °C) (CTE_{(25–800 °C)}) value of 1.73 × 10^?6 °C^?1. Meanwhile, the thermal shock resistance properties evaluation of the LAS glass-ceramics at different ZnO contents were conducted at different thermal shock temperatures of 200 °C, 500 °C, and 800 °C. The critical temperature of the LAS specimens with 1.45 wt% ZnO demonstrated the ability to withstand a thermal shock at 800 °C while preserving 87% of their initial strength of 108.40 MPa, exemplifying the best LAS glass-ceramics properties for rapid high-temperature change applications.     

Mechanical and functional properties of Al2O3–ZrO2–MWCNTs nanocomposites

Multi-walled carbon nanotubes (MWCNTs) are often reported as additives improving mechanical and functional properties of ceramic composites. However, despite tremendous efforts in the field in the past 20 years, the results are still inconclusive. This paper studies room temperature properties of the composites with polycrystalline alumina matrix reinforced with 0.5–2 vol.% MWCNTs (composites AC) and zirconia toughened alumina with 5 vol.% of yttria partially stabilised zirconia (3Y-PSZ) containing 0.5–2 vol.% of MWCNTs (composites AZC). Dense composites were prepared through wet mixing of the respective powders with functionalised MWCNTs, followed by freeze granulation, and hot-pressing of granulated powders. Room temperature bending strength, Young's modulus, indentation fracture toughness, thermal and electrical conductivity of the composites were studied, and related to their composition and microstructure. Slight increase of Young's modulus, indentation fracture toughness, bending strength, and thermal conductivity was observed at the MWCNTs contents ≤1 vol.%. At higher MWCNTs contents the properties were impaired by agglomeration of the MWCNTs. The DC electrical conductivity increased with increasing volume fraction of the MWCNTs.     

Particle occlusion and mechanical properties of Ni–Al2O3 nanocomposites

Polycrystalline alumina, doped with MgO below the solubility limit, was reinforced with sub-micron particles of Ni by infiltration of Ni-nitrate into fired alumina green bodies, followed by reduction and sintering. The Ni particle size and location were monitored both after reduction and after sintering by transmission electron microscopy. Particle occlusion was found to increase with sintering time and temperature, and is correlated with experimentally detected Mg segregation to the Ni–alumina interfaces, resulting in partial depletion of Mg at the alumina grain boundaries and thus their increased mobility. Occlusion of Ni particles reduces the fracture strength and Weibull modulus of the composites, indicating that particle location is a key microstructural parameter for reaching high fracture strengths, and that this can be controlled via grain boundary and interface adsorption.     

Effect of different corundum sources on microstructure and properties of Al2O3–Cr2O3 refractories

Al₂O₃–Cr₂O₃ refractories are completely substitutional solid solutions and exhibit better corrosion and abrasion resistance. To enable the comprehensive utilization of it, the microstructure and properties of Al₂O₃–Cr₂O₃ samples with different corundum sources were investigated in this study. The starting sources of corundum sources included sintered tabular corundum, fused white corundum, or brown corundum with minor impurities of β-Al₂O₃ and TiO₂. The results of mechanical test showed that the introduction of white corundum deteriorates the physical structure, while brown corundum acts in an opposite manner. The optimum bonding strength of the Al₂O₃–Cr₂O₃ brick was reached by combining white and brown corundum, whereby rapid neck growth occurred via surface diffusion during solid-phase sintering.     

Optimized sintering and mechanical properties of Y–TZP ceramics for dental restorations by adding lithium disilicate glass ceramics

The novel dental ceramics can be fabricated at lower temperatures when sol–gel derived lithium disilicate glass ceramics (LDGC) was used as an additive for yttr...     

Effect of lattice structure evolution on the thermal and mechanical properties of Cu–Al2O3/GNPs nanocomposites

In this study, high-energy ball milling accompanied by compaction and sintering were employed for manufacturing Cu-based hybrid nanocomposite reinforced by Al₂O₃ and GNPs. This hybrid nanocomposite is proposed to meet the specification of heat sink applications, where excellent mechanical and thermal performance is demanding. Different processing parameters were experimentally considered such as sintering temperature and weight percentage of GNPs, 0, 0.25, 0.50, 0.75, and 1 wt %. The weight percentage of Al₂O₃ was fixed at 10%. The results demonstrated that the mechanical and thermal performance of the fabricated nanocomposites were superior for nanocomposite containing 0.5% GNPs and sintered at 1000 °C. The hardness, the thermal conductivity and the coefficient of thermal expansion (CTE) were improved by 21%, 16.7%, and 55.2%, respectively, compared to composite without GNPs addition. The improved mechanical and thermal properties were attributed to the low stacking fault energy, small crystallite size, high dislocation density, and low lattice strain of the composite prepared at this composition. Moreover, the better dispersion of the nano-particles of GNPs and Al₂O₃ inside the matrix helped for the strength and thermal conductivity improvement while maintaining low CTE.     

Effect of ZrO2 addition on in-vitro bioactivity and mechanical properties of SiO2–Na2O–CaO–P2O5 bioactive glass-ceramic

Herein, a multicomponent bioactive glass (0Z, 46SiO₂–30CaO–18Na₂O–6P₂O₅, wt.%) is prepared via melting. ZrO₂ is introduced into the bioglass using two different methods, and then three types of glass-ceramic bulks are manufactured using low-cost pressureless sintering. The effect of ZrO₂ addition on the bioactivity and mechanical properties of the bioactive glass-ceramic is assessed. The results indicate that the main crystalline precipitate from the bioactive glass-ceramic is Na₂Ca(Si₂O₆). The crystallisation ability of the 5Z glass-ceramic, bioactive glass-ceramic with ZrO₂ added during melting at high temperature, is reduced because ZrO₂ participated in the reconstruction of the glass network. Further, the ZrO₂ addition led to a low rate of cation release when soaked in simulated body fluid, indicating a decreased bioactivity. At the same time, the 5Y bioactive glass-ceramic, prepared by mixing YSZ particles with 0Z using ball-milling, possesses not only the highest mechanical strength (about twice the strength of 0Z) but also a high bioactivity. This study presents a promising method for the production of excellent bioactive glass-ceramic and a candidate (5Y) for the clinical applications where load bearing is required.     

Fabrication of Al2O3–ZrO2 ceramics with high porosity and strength

This study describes the synthesis of ceramics, in which a micrometre-sized Al₂O₃–ZrO₂ nanopowder was used as an oxide base for the hardening of the materials. To a suspension of this mixed metal oxide, the pore-forming crystallisation additives camphor and carbamide were added to produce ceramics with thin permeable pores. Camphor crystallised in the oxide suspension in the form of single pentagonal stars and сarbamide crystallised in the form of thin elongated needles. The use of the different crystallisation additives allowed the formation of ceramics after sintering that have both permeable and complex pore morphologies, where anisotropic properties were observed using carbamide as an additive but not when camphor was used. The total porosity of the resulting ceramics was 51.3%, with a compressive strength in the range of 17.3–92.3 MPa.