Structural,dielectric and ferroelectric properties of Ba1−x(Bi0.5Na0.5)xTiO3 ceramics

Lead free Ba_1?x(Bi_0.5Na_0.5)_xTiO₃ (x=0, 0.02, 0.04, 0.06, 0.08, 0.1) ferroelectric ceramics were synthesized by conventional solid state reaction technique. Sintering was done at 1200 °C for 2 h in air atmosphere. The final products have tetragonal symmetry with decreasing c/a ratio confirmed by X-ray diffraction analysis. The grain size varies between 300 nm to 1000 nm for x=0 to 0.1. With increase in Bi_0.5Na_0.5TiO₃ [BNT] content, the room temperature permittivity decreases whereas the Curie temperature (T_c) increases and its highest value was found to be 155 °C for 10 mol% of BNT addition. The ceramics show stable and low dielectric loss characteristics. The remnant polarization (P_r) and the coercive field (E_c) increases monotonously with increase in BNT content. The highest value of 2P_r (=17 μC/cm²) and 2E_c (=22 Kv/cm) was obtained for x=10 mol% BNT addition.     

Structural properties of (Bi0.5Na0.5)1−xBaxTiO3 lead-free piezoelectric ceramics

A systematic XRD investigation of poled and unpoled ceramics of the system (1 ? x) Bi_0.5Na_0.5TiO₃–x BaTiO₃ (0 ≤ x ≤ 0.2) (BNBT) was performed. The variation of the lattice parameters confirms the existence of a morphotropic phase boundary at 0.06 ≤ x ≤ 0.08; however, significant differences in unit cell parameters between poled and unpoled states appear. Lattice distortions of the rhombohedral and tetragonal phases are significantly increased in poled samples. Dramatic changes in peak intensities of the pseudo-cubic (2 0 0) reflections between poled and unpoled samples reveal a strong enhancement of the tetragonal volume fraction in the poled state. Temperature-dependent XRD studies confirm a transition into a cubic high-temperature phase. This transition is rather smooth in the unpoled state. In poled samples, the tetragonal distortion and the tetragonal volume fraction display a different temperature variation and tetragonal regions seem to persist into the cubic phase field.     

Effect of WO3 doping on dielectric and ferroelectric properties of 0.94(Bi0.5Na0.5)TiO3–0.06BaTiO3 ceramics

WO₃(0–6 mol%)-doped 0.94Bi_0.5Na_0.5TiO₃–0.06BaTiO₃ lead-free ceramics were synthesized by conventional solid-state reaction. The effect of WO₃ addition on the structure and electrical properties were investigated. The result revealed that a small amount of WO₃ (≤1 mol%) can diffuse into the lattice and does not significantly affect the phase structure, however, more addition will result in distortion and enlargement of the unit cells. The maximum permittivity temperature (T_m) is suppressed dramatically as the dopant increasing, while the depolarization temperature (T_d) fall to the minimum with 1 mol% WO₃ additive. The remanent polarization (P_r) was enhanced and coercive field (E_c) was reduced by doping with WO₃. The strain shows the largest value for 1 mol% doped sample, which is due to a field-induced antiferroelectric–ferroelectric phase transition.     

Enhancing the dielectric and energy storage properties of lead-free Na0.5Bi0.5TiO3–BaTiO3 ceramics by adding K0.5Na0.5NbO3 ferroelectric

A novel strategy of enhancing the dielectric and energy storage properties of Na_0.5Bi_0.5TiO₃–BaTiO₃ (NBT–BT) ceramics by introducing a K_0.5Na_0.5NbO₃ (KNN) ferroelectric phase is proposed herein, and its underlying mechanism is elucidated. The lead-free KNN ceramic decreases the residual polarisation and increases the electric breakdown strength of the NBT–BT matrix through the simultaneous modification of its A-sites and B-sites. The obtained NBT?BT?x?KNN ceramics have a perovskite structure with unifying grains. A bulk 0.9NBT–BT–0.1KNN ceramic sample with a thickness of 0.2 mm possesses a high energy storage density of 2.81 J/cm³ at an applied electric field of 180 kV/cm. Moreover, it exhibits good insulation properties and undergoes rapid charge and discharge processes. Therefore, the obtained 0.9NBT–BT–0.1KNN ceramic can be potentially used in high-power applications because of its high energy density, good insulation properties, and large discharge rate.     

Effect of lanthanum substitution on microstructure and electrical properties of (Bi0.5Na0.5)1−1.5xLaxTi0.41Zr0.59O3 ceramics

Bismuth sodium zirconate (BNZ) based ceramics with a composition of (Bi_0.5Na_0.5)_1?1.5xLa_xTi_0.41Zr_0.59O₃ where x = 0, 0.005, 0.01, 0.02 and 0.03 were prepared by a solid-state mixed oxide method and sintered at the temperature of 900 °C for 2 h. All the samples had relative density between 91 and 97% of their theoretical values. Phase analysis using X-ray diffraction indicated single rhombohedral or pseudo-cubic perovskite structure. SEM showed that addition of La caused the average grain size of the BNTZ ceramics to decrease as well as an improvement of sample density. Dielectric properties at room temperature measured at 10 kHz indicated that addition of La increased the dielectric constant. The results of ferroelectric characterization also revealed that adding La caused a decrease in coercive field without affecting the remanent polarization.     

Microwave dielectric properties and microstructures of Nd(Mg0.5Sn0.5−xTix)O3 ceramics

This study elucidates the microwave dielectric properties and microstructures of Nd(Mg_0.5Sn_0.5?xTi_x)O₃ ceramics with a view to their potential for microwave devices. The Nd(Mg_0.5Sn_0.5?xTi_x)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the Nd(Mg_0.5Sn_0.4Ti_0.1)O₃ ceramics revealed no significant variation of phase with sintering temperatures. A dielectric constant (?_r) of 21.1, a quality factor (Q × f) of 50,000 GHz, and a temperature coefficient of resonant frequency (τ_f) of ?60 ppm/°C were obtained for Nd(Mg_0.5Sn_0.4Ti_0.1)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Microwave dielectric properties of (Ba1−xSrx)(Mg0.5W0.5)O3 ceramics

The densification, microstructural evolution and microwave dielectric properties of (Ba_1−xSr_x)(Mg_0.5W_0.5)O₃ ceramics with x=0, 0.25, 0.5 and 0.75 are investigated in this study. The sintering temperature of the (Ba_1−xSr_x)(Mg_0.5W_0.5)O₃ is significantly reduced from 1575 °C to 1400 °C as the x value increases from 0 to 0.25 and 0.50; this result is accompanied by the formation of the (Ba_1−ySr_y)WO₄ phase and a small quantity of second phase surrounding the grains. The grain size of the (Ba_1−xSr_x)(Mg_0.5W_0.5)O₃ ceramics is increased by raising the Sr²⁺ content, which significantly lowers the sintering temperature. The microstructure of the (Ba_0.75Sr_0.25)(Mg_0.5W_0.5)O₃ ceramic displays the smallest average grain size of approximately 0.8 μm, with a narrow grain size distribution. Without long annealing time, very high Q×f values are obtained for the (Ba_1−xSr_x)(Mg_0.5W_0.5)O₃ ceramics sintered at 1400–1575 °C for a duration of only 2 h. The (Ba_0.75Sr_0.25)(Mg_0.5W_0.5)O₃ ceramic sintered at 1400 °C results in the best microwave dielectric properties, including ε_r of 20.6, Q×f of 152,600 GHz and τ_f of +24.0 ppm/°C.     

Structure,dielectric, and ferroelectric properties of (1-x)Bi0.5Na0.5TiO3 – X K0.5Na0.5NbO3 (0 ≤ x ≤ 0.1) solid solution

The correlation of the phase structure, dielectric, and ferroelectric properties of lead-free (1-x)(Na_0.5Bi_0.5)TiO₃–xK_0.5Na_0.5NbO₃ (NBTKNx) (0 = x ≤ 0.1) polycrystalline ceramics, fabricated via a solid state reaction technique, were investigated. The Rietveld refinement allowed identifying the crystallographic transformation from a rhombohedral to a coexisting rhombohedral-tetragonal or tetragonal long range-ordered ferroelectric (FE) phase. The dielectric investigations showed an increase of the dielectric diffuseness (1.53 = γ ≤ 1.73) and a clear shift of the depolarization temperature (T_d) to a lower temperature while increasing substitution. More importantly, the lattice disorder also generated a plateau-like dielectric anomaly, leading to a thermally stable ϵ_r ∼2859 ± 20% (120–500 °C) and ∼3112 ± 10% (120–420 °C) for x = 0.075 and 0.1 samples, respectively. At room temperature (RT), Raman spectroscopy investigations revealed a downshift of the frequencies as a function of the composition with an inhomogeneous broadening of the Raman lines. On heating, Raman spectra showed changes in the region where the dielectric transitions are observed. Moreover, the composition dependence of the current peaks in the I-E loops confirmed the occurrence of a phase transition from a non-ergodic polar phase to an ergodic weakly polar after the applying of an electric field of 60 kV/cm⁻¹.     

Morphotropic phase boundary and electrical properties of lead-free (K0.5Bi0.5)TiO3–Bi(Ni0.5Ti0.5)O3 relaxor ferroelectric ceramics

Lead-free relaxor ferroelectric ceramics (1?x)(K_0.5Bi_0.5)TiO₃–xBi(Ni_0.5Ti_0.5)O₃ were prepared by a conventional solid-state route, the phase transition behavior and corresponding electrical properties were investigated. A typical morphotropic phase boundary (MPB) between rhombohedral and tetragonal ferroelectric phases was identified to be in the range of 0.05<x<0.07 where the optimum piezoelectric and electromechanical properties of d₃₃=126 pC/N and k_P=18% were achieved. Most importantly, a high Curie temperature ~320 °C, around which the material shows a typical relaxor ferroelectric behavior characterized by the presence of diffuse phase transition and frequency dispersion, was obtained in MPB compositions, significantly higher than those of some existing MPB lead-free titanate systems. These results demonstrate a tremendous potential of the studied system for device applications.     

Structure,dielectric and ferroelectric properties of 0.92Na0.5Bi0.5TiO3–0.06BaTiO3–0.02K0.5Na0.5NbO3 lead-free ceramics: Effect of Co2O3 additive

0.92Na_0.5Bi_0.5TiO₃–0.06BaTiO₃–0.02K_0.5Na_0.5NbO₃+x wt% Co₂O₃ (NBKT–xCo, x=0, 0.2, 0.4, 0.6, 0.8) lead-free ferroelectric ceramics were prepared via a conventional solid state reaction method. Effects of Co₂O₃ additive on crystallite structure, microstructure, dielectric and ferroelectric properties of the NBKT–xCo ceramics were studied. X-ray diffraction results showed that the rhombohedral–tetragonal morphotropic phase boundary existed in all the ceramics, with relative amount of tetragonal phase varying with the content of Co₂O₃. Average grain size, maximum value of dielectric constant, Curie temperature and ferroelectric properties of the ceramics were close related to the content of Co₂O₃. The dielectric anomaly caused by the phase transition between the ferroelectric phase and the so-called “intermediate phase” was observed in the ceramics with x≤0.2, while it disappeared with further increasing x. All the ceramics showed a diffuse phase transition between the “intermediate phase” and the paraelectric phase. The change in the ferroelectric properties with changing the content of Co₂O₃ was discussed by considering the competitive effects among grain size, relative amount of the tetragonal phase and oxygen vacancies.     

Phase structure,piezoelectric, ferroelectric,and electric-field-induced strain properties of Nb-modified 0.8Bi0.5Na0.5TiO3−0.2Sr0.85Bi0.1TiO3 ceramics

0.8Bi_0.5Na_0.5Ti_(1-x)Nb_xO₃−0.2Sr_0.85Bi_0.1TiO₃ (BNT-SBT-xNb, x = 0.00, 0.01, 0.02, and 0.03) piezoelectric ceramics were prepared by traditional solid state reaction and the influence of Nb substitution on the phase structure, ferroelectric, piezoelectric, and electric-field-induced strain properties in BNT-SBT ceramics were studied. XRD results exhibited that Nb⁵⁺ ions could fully diffuse into BNT-SBT structure to form a solid solution when x = 0.01. P-E loops and S-E curves suggested that the ferroelectric phase transformed to ergodic relaxor state (FE-to-ER) with the increasing the amount of Nb additive, indicating the ferroelectric long-ranged order was disturbed by the excess of Nb. With increasing Nb doping, phase transition temperature from normal ferroelectric to ergodic relaxor (short for T_F-R) could be reduced from 120 °C to 40 °C. Furthermore, for sample with x = 0.01, the normalized strain d₃₃^* got a maximum value ~571 pm/V due to the phase transition from ergodic relaxor to ferroelectric (ER-to-FE) under electric field.     

Phase transition behavior and electrical properties of lead-free (Bi0.5K0.5)TiO3–LiNbO3 relaxor ferroelectric ceramics

(1?x)(Bi_0.5K_0.5)TiO₃–xLiNbO₃ ((1?x)BKT–xLN) lead-free relaxor ferroelectric ceramics were prepared by a conventional solid-state route and their phase transition behavior and the corresponding electrical properties were investigated. A morphotropic phase boundary separating rhombohedral and tetragonal phases was identified in the composition range of 0.015<x<0.03, where the improved electrical properties of piezoelectric constant d₃₃=75 pC/N and electromechanical coupling factor k_p=0.18 were obtained. Moreover, all samples show typical relaxor behavior characterized by the presence of diffuse phase transition and frequency dispersion. It was found that the dielectric relaxation behavior of BKT ceramics can be obviously enhanced with the addition of LN. In addition, the effect of the LN addition on the ferroelectric properties was also investigated by measuring polarization versus electric field hysteresis loops.     

The electrical properties of (1−x)(Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3–BaTiO3)–xCaZrO3 lead-free piezoelectric ceramics

Lead-free (1−x)(0.0852Bi_0.5Na_0.5TiO₃–0.12Bi_0.5K_0.5TiO₃–0.028BaTiO₃)–xCaZrO₃ piezoelectric ceramics (BNT−BKT−BT−xCZ, x=0, 0.01, 0.02, 0.03, 0.04 and 0.05) were prepared by using a conventional solid-state reaction method. The effects of CZ-doping on the structural, dielectric, ferroelectric and piezoelectric properties of the BNT−BKT−BT−xCZ system were systematically investigated. The polarization and strain behaviors indicated that the long-range ferroelectric order in the unmodified BNT−BKT−BT ceramics was disrupted by the increase of CZ-doping content, and correspondingly the depolarization temperature (T_d) shifted down from 109 °C to below room temperature. When x>0.03, accompanied with the drastic decrease in the remnant polarization (P_r) and piezoelectric coefficient (d₃₃), the electric-field-induced strain was enhanced significantly. A large unipolar strain of 0.35% under an applied electric field of 70 kV/cm (S_max/E_max=500 pm/V) was obtained in the BNT−BKT−BT−0.04CZ ceramics at room temperature, which was attributed to the reversible electric-field-induced phase transition between the relaxor and ferroelectric phases.     

The effect of morphotropic phase boundary on dielectric properties of Bi0.5Na0.5Ti1−xZrxO3 solid solutions

Lead-free bismuth sodium titanate zirconate (Bi_0.5Na_0.5Ti_1?xZr_xO₃ or BNTZ) solid solutions with varied composition of x=0.50, 0.55, 0.58, 0.60, 0.63, 0.65, 0.68, 0.70, 0.73, 0.75 and 0.78 mol fraction were obtained using a conventional mixed-oxide method. XRD analysis indicated that the increase in concentration of Zr led to compositions across morphotropic phase boundary region. A quantitative structural investigation was carried out using the X-ray powder diffraction data. The rhombohedral phase was found to dominate for x<0.68 with space group R3c. In the morphotropic phase boundary (MPB) region i.e. 0.68≤x≤0.75, it was demonstrated that coexistence of rhombohedral and orthorhombic phase was observed. For x=0.78, the phase was completely orthorhombic with space group Pmna. Furthermore, the dielectric properties showed some enhanced activity of dipole movement at MPB boundaries which supported the presence of MPB region in this material system.     

Peculiar dielectric properties of (1-x)(K,Na)(Nb,Sb)O3−x(Bi,Na)ZrO3 ceramics

In spite of the significance from both scientific and technological viewpoints, systematical studies on the dielectric spectra of (K,Na)NbO₃-based lead-free ceramics particularly in the poled state had been scarcely performed so far. In this study, the compositional series of (1-x)(K_0.48Na_0.52)(Nb_0.96Sb_0.04)O₃?x(Bi_0.50Na_0.50)ZrO₃ ceramics were chosen representatively to shed more light on the characters of dielectric properties. All the ceramics in the unpoled state show dielectric spectra of large dispersion with the relaxational characteristic frequency higher than the measured upper limit of 60 MHz at room temperature. Additional resonance peaks due to the electromechanical coupling of piezoelectric effect appear and are accompanied by a large step-like reduction of dielectric permittivity ε′ in the dielectric spectra after poling. An abnormal phenomenon that poling induces the increase of low-frequency ε′ occurs in those ceramics with x ≥ 0.04 at room temperature, and is confirmed to associate closely with the orthorhombic-tetragonal and rhombohedral-orthorhombic polymorphic phase transitions. Further study of domain structure indicates that the origin of this abnormal phenomenon should be ascribed to the enhancement of domain-wall mobility because of the large reduction of domain-wall density due to the poling.     

Structure,relaxation behaviors and nonlinear dielectric properties of BaTiO3–Bi(Ti0.5Mg0.5)O3 ceramics

(1−x)BaTiO₃–xBi(Mg_1/2Ti_1/2)O₃ (BT–BMT, x=0–0.2, abbreviated as BT–BMT100x) ceramics were prepared by using a solid state reaction process. Their crystal structure, microstructure, conduction behavior, dielectric and tunability properties were investigated. It is found that the tetragonal phase and a pseudocubic phase coexist for x≤0.15 and transform to a pseudocubic phase at x=0.20. With the incorporation of BMT, BT–BMT becomes more insulating. The activation energies of the conduction are respectively 1.15(1) and 1.54(1) eV for grain and grain boundary of BT–BMT20. Furthermore, an abnormal nonlinear dielectric tunable behavior is observed. The dielectric permittivity first slightly increases until reaching the threshold electric field, and then suddenly decreases. This abnormal nonlinear dielectric behavior is attributed to the synergetic effects of the clamped oxygen vacancies and excessive aggregation of Bi at the grain boundaries.     

Phase formation,dielectric and ferroelectric properties of CaxBa1−xNb2O6 ceramics

Lead-free Ca_xBa_1?xNb₂O₆ (CBN, 0.20≤x≤0.35) ceramics were prepared by the conventional solid state method. Effects of Ca content on the phase formation, microstructure, dielectric and ferroelectric properties for the prepared CBN ceramics were systematically studied. XRD results showed that pure CBN phase with tungsten bronze structure could be obtained from the solid solutions of BaNb₂O₆ and CaNb₂O₆ in all ceramics. Higher Ca contents favored the occurrence of grains with anisometric morphology, but no abnormal grain growth could be found in all compositions. With the increase of x, Curie temperature T_c shifted downward, whereas the maximum dielectric constant ε_m increased initially and then decreased. All the ceramics showed an intermediate relaxor-like behavior between normal and ideal relaxor ferroelectrics according to the modified Curie–Weiss law. Normal ferroelectric hysteresis loops were observed in all compositions. Both remnant polarization P_r and coercive field E_c increased initially and then decreased with the increase of x. The ceramics with homogeneous microstructure, high density and better properties were obtained at x=0.28 with ε_m=2998, T_c=234 °C, P_r=3.98 μC cm^?2 and E_c=14.03 kV cm^?1.