还原温度对Mo基催化剂物相及其加氢脱氧性能的影响

以碳纳米管(CNTs)为载体,通过控制催化剂合成的还原温度制备了一系列负载型Mo基催化剂。采用XRD、TEM、N₂物理吸附、XPS以及NH₃/H₂-TPD等技术对催化剂进行了表征,并研究了Mo基催化剂对硬脂酸催化加氢脱氧性能的影响。结果表明:随着还原温度的升高,催化剂表面的Mo物种逐渐被还原,还原过程为:MoO₃→MoO₂→Mo→Mo₂C。还原温度为450℃和550℃时,催化剂的活性相为MoO₂;还原温度为600℃时,催化剂的活性相为MoO₂/Mo/β-Mo₂C的混合相;还原温度为650℃和700℃时,催化剂的活性相全部转化为β-Mo₂C。与活性相MoO₂催化剂相比,β-Mo₂C催化剂具有更高的加氢脱氧活性。此外,还原温度为600℃的MoO₂/Mo/β-Mo₂C混合相催化剂因具有较大的比表面积、较多的酸中心数量和较强的H₂吸附能力,使得该催化剂在硬脂酸加氢脱氧反应中表现出最优越的催化活性。     

Heterogeneous base catalyzed synthesis of 2-oxazolidinones/2-imidiazolidinones via transesterification of ethylene carbonate with β-aminoalcohols/1,2-diamines

Several heterogeneous basic metal oxide catalysts were screened for the synthesis of 2-oxazolidinones and 2-imidiazolidinones via transesterification of ethylene carbonate with different β-aminoalcohols or 1,2-diamines. Among the several catalysts screened, MgO was found to be the best catalyst, as it has excellent recyclability. Various reaction parameters were studied in detail. Excellent yields of the products were obtained using MgO as catalysts at 80 °C within 6 h in ethanol. Basic properties of the metal oxide catalysts were compared using temperature programmed desorption (TPD) studies with CO₂. The relationship between the catalyst performance and the basic property of each catalyst has been discussed.     

Hydrodesulfurization over supported monometallic, bimetallic and promoted carbide and nitride catalysts

The preparation of alumina-supported β-Mo₂C, MoC_1−x (x≈0.5), γ-Mo₂N, Co–Mo₂C, Ni₂Mo₃N, Co₃Mo₃N and Co₃Mo₃C catalysts is described and their hydrodesulfurization (HDS) catalytic properties are compared to conventional sulfide catalysts having similar metal loadings. Alumina-supported β-Mo₂C and γ-Mo₂N catalysts (Mo₂C/Al₂O₃ and Mo₂N/Al₂O₃, respectively) are significantly more active than sulfided MoO₃/Al₂O₃ catalysts, and X-ray diffraction, pulsed chemisorption and flow reactor studies of the Mo₂C/Al₂O₃ catalysts indicate that they exhibit strong resistance to deep sulfidation. A model is presented for the active surface of Mo₂C/Al₂O₃ and Mo₂N/Al₂O₃ catalysts in which a thin layer of sulfided Mo exposing a high density of sites forms at the surface of the alumina-supported β-Mo₂C and γ-Mo₂N particles under HDS conditions. Cobalt promoted catalysts, Co–Mo₂C/Al₂O₃, have been found to be substantially more active than conventional sulfided Co–MoO₃/Al₂O₃ catalysts, while requiring less Co to achieve optimal HDS activity than is observed for the sulfide catalysts. Alumina-supported bimetallic nitride and carbide catalysts (Ni₂Mo₃N/Al₂O₃, Co₃Mo₃N/Al₂O₃, Co₃Mo₃C/Al₂O₃), while significantly more active for thiophene HDS than unpromoted Mo nitride and carbide catalysts, are less active than conventional sulfided Ni–Mo and Co–Mo catalysts prepared from the same oxidic precursors.     

负载型磷钼钒钴杂多酸盐催化氧化乙苯合成苯乙酮

采用浸渍法制备了系列负载型杂多酸盐催化剂,并将其应用于乙苯氧化合成苯乙酮的反应中。考察了载体类型、负载量、焙烧温度、催化剂用量、反应时间等因素对催化活性的影响。结果表明,以HZSM-5为载体,杂多酸盐Co_4HP_2Mo_（15）V_3O_（62）负载量30%,固定乙苯用量25mmol,催化剂用量0.4g,m（催化剂）：m（KBr）=2：3,n（乙苯）：n（过氧化氢）=0.125：1,反应温度80℃.反应时间1h,乙苯转化率达到82.21%,苯乙酮收率为55.75%。     

CuO/HZSM-5催化溴甲烷芳构化制备芳烃

采用等体积浸渍法制备了不同负载量（1%~7%）的CuO/HZSM-5催化剂,在固定床反应器中研究了不同反应温度、溴甲烷流量以及CuO负载量对溴甲烷芳构化催化性能的影响。采用SEM、XRD、N₂吸附脱附、TEM、XPS、TG、DSC、NH₃-TPD等技术对反应前后的催化剂进行表征。XRD 结果显示活性组分CuO 在HZSM-5上具有很好的分散性,并且反应后Cu晶型不变。NH₃-TPD 结果显示3%的CuO 负载后,催化剂强酸量增加。在CuO 负载量为3%,温度为360℃,反应空速为240 ml·g^-1·h^-1 条件下得到最高的芳烃收率（22.3%）。XPS 结果显示反应后在催化剂上主要的积炭为石墨碳。催化剂稳定性测试结果表明反应40 h内催化活性没有明显下降。     

Coke study on MgO-promoted Ni/Al2O3 catalyst in combined H2O and CO2 reforming of methane for gas to liquid (GTL) process

MgO-promoted Ni/Al₂O₃ catalysts have been investigated with respect to catalytic activity and coke formation in combined steam and carbon dioxide reforming of methane (CSCRM) to develop a highly active and stable catalyst for gas to liquid (GTL) processes. Ni/Al₂O₃ catalysts were promoted through varying the MgO content by the incipient wetness method. X-ray diffraction (XRD), BET surface area, H₂-temperature programmed reduction (TPR), H₂-chemisorption and CO₂-temperature programmed desorption (TPD) were used to observe the characteristics of the prepared catalysts. The coke formation and amount in used catalysts were examined by SEM and TGA, respectively. H₂/CO ratio of 2 was achieved in CSCRM by controlling the feed H₂O/CO₂ ratio. The catalysts prepared with 20 wt.% MgO exhibit the highest catalytic performance and have high coke resistance in CSCRM. MgO promotion forms MgAl₂O₄ spinel phase, which is stable at high temperatures and effectively prevents coke formation by increasing the CO₂ adsorption due to the increase in base strength on the surface of catalyst.     

Comparison between tungsten carbide and molybdenum carbide for the hydrodenitrogenation of carbazole

The activity of molybdenum and tungsten carbides in hydrodenitrogenation (HDN) of carbazole was studied. Transition metal carbides (Mo₂C and W₂C) were synthesized using the temperature-programmed reaction of the appropriate oxide precursor (MoO₃ and WO₃) with the following gas mixture: 10 vol.% CH₄/H₂. The structure of the catalysts was characterized using X-ray diffraction, CO chemisorption, high resolution transmission electron microscopy (HRTEM) and BET surface area measurements. From the HRTEM analysis, it could be concluded that the tungsten carbide was thioresistant in our operating conditions (50 ppm of S, pressure = 6 MPa, 553 < T < 653 K, H₂/feed volumic ratio = 600). In the case of Mo₂C, molybdenum sulphide was observed as single slabs. The activity of catalysts was determined during the hydrodenitrogenation of carbazole at the wide range of temperature (553–653 K) and under a 6 MPa total pressure of H₂. The comparison of tungsten carbide and molybdenum carbide has shown higher activity of Mo₂C than W₂C at the same condition. However, W₂C leads to higher amount of isomers of main products, and have higher hydrogenation activity.     

溶胶-凝胶原位合成宽活性温度V2O5/TiO2脱硝催化剂

利用溶胶-凝胶技术原位合成一系列不同V₂O₅担载量的V₂O₅/TiO₂催化剂,通过BET、XRD、NH₃-TPD及紫外-可见光等手段对催化剂进行表征。结果表明：制备的催化剂均具有介孔结构,V₂O₅在TiO₂表面高度分散,且存在3种典型的酸性位。通过选择性催化还原反应对V₂O₅/TiO₂催化剂进行活性评价,结果显示随着V₂O₅含量的增加,NO转化率大于75%的温度窗口向低温方向偏移,含10% （质量分数）V₂O₅的催化剂的NO转化率为80%的温度窗口最宽为200～450℃,240℃时20 h连续实验表现出稳定的抗硫抗水性能。结合紫外-可见光谱分析,揭示了钒掺杂所形成的单聚和低聚钒酸盐为催化剂的活性组分。     

Activity of carbided molybdena–alumina for CO2 hydrogenation

The relationship between the catalytic activity of carbided molybdena–alumina and the methane desorption from carbidic carbon through temperature-programmed surface reaction (TPSR) were studied. The effects of passivation and hydrogen treatment on the catalytic activities of molybdenum carbides for CO₂ hydrogenation were determined. When the 973 K-carbided catalyst was reduced at 773 K with hydrogen, the catalyst exhibited the highest activity for the reaction, the activity decreasing with increasing H₂ pretreatment temperature. Passivation of this catalyst decreased the reaction rate by 20%. TPSR results were correlated with the activity to reveal that molybdenum carbide with slightly deficient carbidic carbon (Mo₂C_0.962C_1.0) serves as an active site for CO₂ hydrogenation.     

固体酸表面B酸和L酸与果糖转化制乳酸甲酯产物分布

制备了γ-Al₂O₃、HZSM-5、SnOPO₄、SnZrOPO₄(1:1)、SO₄^2-/ZrO₂5种不同的固体酸催化剂,采用NH₃程序升温脱附、吡啶原位吸附红外对催化剂进行了表征。考察了固体酸催化果糖在甲醇中转化的催化性能,结果表明,果糖的转化率均高于98%,产物分布与固体酸表面L酸、B酸酸量具有显著的相关性,乳酸甲酯的收率随着L酸量的减少而降低,L酸催化剂γ-Al₂O₃催化,主产物只有乳酸甲酯,收率为24.4%。而L酸位和B酸位共存的固体酸,产物中有乳酸甲酯、乙酰丙酸甲酯,并且乙酰丙酸甲酯的收率随着B酸量的增多而升高。最后考察了典型L酸γ-Al₂O₃及B酸L酸共存的固体酸HZSM-5不同反应时间的产物分布,结合气相-质谱联用对产物定性分析,得出了果糖转化过程L酸位催化和B酸位催化的反应路径。     

Methane aromatization using Mo-based catalysts prepared by microwave heating

Mo/HZSM-5 and Cu–Mo/HZSM-5 catalysts for the non-oxidative aromatization of methane have been prepared by microwave heating method. The effects of Mo loading, the molar ratio of Cu/Mo and preparation method on the catalytic performance of catalysts were studied. The results were compared with those for the methane aromatization over catalysts prepared by conventional heating. Both two kinds of catalysts have the maximum methane conversion when the Mo loading is 6%. The catalysts prepared by microwave heating exhibited higher selectivity to benzene than that prepared by conventional heating. The addition of metal Cu to Mo/HZSM-5 catalyst prepared by microwave heating enhanced the lifetime of catalyst, and gave rise to a little increase in methane conversion. The molar ratio of Cu/Mo influenced the methane conversion, and the maximum value was attained when Cu/Mo = 0.05, whereas no significant influence on the benzene selectivity was observed with the increase molar ratio of Cu/Mo. N₂ adsorption results showed that the catalysts prepared by microwave heating have the larger surface area and the similar pore volume compared with the catalysts prepared by conventional heating. This fact revealed that the more Mo species located on the outer surface of catalysts prepared by microwave heating is the main reason why they have better catalytic performance. XRD analysis indicated that the Mo species are highly dispersed on HZSM-5 zeolite. The addition of Cu influenced the dispersion. The actual active phase Mo₂C can be identified on the catalyst surface after reaction. TEM analysis revealed the carbonaceous deposition to have the form of carbon nanotube after reaction, with a uniform size range of 10–20 nm. TG analysis indicated that carbonaceous deposition on the catalysts prepared by microwave heating is lower than that by conventional heating, and the metal Cu further prompts the stability of catalyst. Most of the carbonaceous deposition on catalysts prepared by microwave heating is formed at low temperature and it is easy to burn-off. Coke accumulation at high temperature is the main reason of catalyst deactivation. The carbonaceous deposition formed on the catalysts for non-oxidative aromatization of methane is different from those formed on the catalysts for partial oxidation of methane.     

MgO/NaX zeolite as basic catalyst for oxidative methylation of toluene with methane

Oxidative methylation of toluene with methane was studied over a series of MgO/NaX zeolite catalysts. The effect of MgO on the zeolite was examined by X-ray diffraction (XRD) and temperature-programmed desorption (TPD) of CO₂. The results indicated that the conversion, selectivity and yield of C₈ hydrocarbons (ethylbenzene and styrene) are significantly improved by impregnation of maximum 13 wt.% MgO into the zeolite. The latter catalyst also displays a good stability. It is found that the amount of active sites but not their strength depends on the content of MgO in the zeolite. The catalysts possess well preserved crystal structure and low amount of MgO crystal phase.     

Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Use of unsupported and silica supported molybdenum carbide to treat chloroarene gas streams

The gas phase catalytic hydrodechlorination (HDC) of mono- and di-chlorobenzenes (423 K ≤ T ≤ 593 K) over unsupported and silica supported Mo carbide (Mo₂C) is presented as a viable means of detoxifying Cl-containing gas streams for the recovery/reuse of valuable chemical feedstock. The action of Mo₂C/SiO₂ is compared with MoO₃/SiO₂ and Ni/SiO₂ (an established HDC catalyst). The pre- and post-HDC catalyst samples have been characterized in terms of BET area, TG-MS, TPR, TEM, SEM, H₂ chemisorption/TPD and XRD analysis. Molybdenum carbide was prepared via a two step temperature programmed synthesis where MoO₃ was first subjected to a nitridation in NH₃ followed by carbidization in a CH₄/H₂ mixture to yield a face-centred cubic (-Mo₂C) structure characterized by a platelet morphology. Pseudo-first order kinetic analysis was used to obtain chlorobenzene HDC rate constants and the associated temperature dependences yielded apparent activation energies that decreased in the order MoO₃/SiO₂ (80 ± 5 kJ mol⁻¹) ≈ MoO₃ (78 ± 8 kJ mol⁻¹) > Ni/SiO₂ (62 ± 3 kJ mol⁻¹) ≈ -Mo₂C (56 ± 6 kJ mol⁻¹) ≈ -Mo₂C/SiO₂ (53 ± 3 kJ mol⁻¹). HDC activity was lower for the dechlorination of the dichlorobenzene reactants where steric hindrance influenced chloro-isomer reactivity. Supporting -Mo₂C on silica served to elevate HDC performance, but under identical reaction conditions, Ni/SiO₂ consistently delivered a higher initial HDC activity. Nevertheless, the decline in HDC performance with time-on-stream for Ni/SiO₂ was such that activity converged with that of -Mo₂C/SiO₂ after three reaction cycles. A temporal loss of HDC activity (less extreme for the carbides) was observed for each catalyst that was studied and is linked to a disruption to supply of surface active hydrogen as a result of prolonged Cl/catalyst interaction.     

Reactivity of V2O5&z.sbnd;WO3TiO2 de-NOx catalysts by transient methods

The reactivity of ternary V₂O₅&z.sbnd;WO₃TiO₂ de-NO_xing catalysts with compositions similar to those of commercial catalysts (WO₃ ca. 9% w/w, V₂O₅ < 2% w/w) is investigated by transient techniques (temperature programmed desorption, TPD; temperature programmed surface reaction, TPSR; and temperature programmed reaction, TPR). The results indicate that the reactivity of the ternary catalysts in the SCR reaction increases on increasing the vanadia loading, and that the ternary catalysts are more active than the corresponding binary vanadia-titania samples with the same V₂O₅ loading. Indeed the SCR reaction is monitored at lower temperatures and high NO conversions are also preserved at high temperatures. TPSR and TPR data show that at low temperatures the SCR reaction occurs via a redox mechanism that involves at first the participation of the catalyst lattice oxygen and then the reoxidation of the reduced sites by gas-phase oxygen. Based on TPSR and TPR data, the higher reactivity of the ternary catalysts has been related to their superior redox properties, in line with previous chemico-physical characterisation studies. The catalyst redox properties thus appear as a key-factor in controlling the reactivity of V₂O₅&z.sbnd;WO₃TiO₂ de-NO_xing catalysts at low temperatures. The results also show that at high temperatures the surface acidity plays an important role in the adsorption and activation of ammonia.     

0.4nm分子筛负载Cu-Ni双金属催化剂用于CO2和CH3OH直接合成碳酸二甲酯（英文）

The 0.4 nm molecular sieve supported Cu-Ni bimetal catalysts for direct synthesis of dimethyl carbonate (DMC) from CO 2 and CH 3 OH were prepared and investigated. The synthesized catalysts were fully characterized by BET, XRD (X-ray diffraction), TPR (temperature programmed reduction), IR (infra-red adsorption), NH 3-TPD (temperature programmed desorption) and CO 2-TPD (temperature programmed desorption) techniques. The results showed that the surface area of catalysts decreased with increasing metal content, and the metals as well as Cu-Ni alloy co-existed on the reduced catalyst surface. There existed interaction between metal and carrier, and moreover, metal particles affected obviously the acidity and basicity of carrier. The large amount of basic sites facilitated the activation of methanol to methoxyl species and their subsequent reaction with activated carbon dioxide. The catalysts were evaluated in a continuous tubular fixed-bed micro-gaseous reactor and the catalyst with bimetal loading of 20% (by mass) had best catalytic activities. Under the conditions of 393 K, 1.1 MPa, 5 h and gas space velocity of 510 h 1 , the selectivity and yield of DMC were higher than 86.0 % and 5.0 %, respectively.     

Simultaneous characterization of acidic and basic properties of solid catalysts by a new TPD method and their correlation to reaction rates

We propose a new TPD method for simultaneously characterizing the acidic and basic properties of solid catalysts by utilizing the co-adsorption of NH₃ and CO₂ on catalysts. First CO₂ was adsorbed on the catalyst sample; then NH₃ was adsorbed on it. Another adsorption sequence of NH₃ and CO₂, and CO₂ and NH₃ single adsorptions were also conducted. The TPD measurements were carried out by heating the catalyst sample from 373 to 773 K at a heating rate of 2.5 K min⁻¹ in a helium stream under a total pressure of 1.3 kPa. In solid acid catalysts, there is little difference in the NH₃-TPD spectra between single and co-adsorption systems. This results from the absence of any induction effect between the acid and base sites, because the number of base sites in the solid acid catalyst is very small. In contrast, in a solid acid–base catalyst of alumina, a remarkable difference in the NH₃-TPD spectra was observed between single adsorption and co-adsorption systems. The difference in the TPD spectra between single and co-adsorption systems was ascribed to a strong induction effect appearing on the acid and base sites, which was proved by an in situ IR measurement. The validity of the TPD method was examined by correlating the number of the strong acid sites to catalytic activities of dehydrolysis of ethanol over solid acid and solid acid–base catalysts. In solid acid–base catalysts, the number of strong acid sites was calculated from the activation energy distribution for the desorption of NH₃ in a co-adsorption system because of the strong induction effect. A proportional relationship between the intrinsic reaction rate constant, which is based on the concentration of ethanol within the catalyst, and the number of strong acid sites could be obtained, regardless of the catalysts or their types or pore structure.     

Synthesis of methacrylic acid by aldol condensation of propionic acid with formaldehyde over acid–base bifunctional catalysts

A variety of catalysts consisting of MgO, SiO₂, Al₂O₃ and ZrO₂, with and without added cesium, were evaluated in the aldol condensation of propionic acid with formaldehyde to produce methacrylic acid. Reactions were performed in a fixed-bed reactor operating at atmospheric pressure and 598 K. Stepwise TPD of pre-adsorbed NH₃ and CO₂ was used to estimate the number and strength of surface acid and base sites, respectively. Both a strong solid base such as MgO and a non-basic solid such as SiO₂ were ineffective at catalyzing the aldol condensation reaction. However, Cs-loaded silica and alumina exhibited moderate activity and high selectivity for the reaction. Results from reactivity measurements and surface characterization suggest that both acid and base sites are needed to catalyze the reaction, and the observed rates over the bifunctional ZrO₂ catalyst support this hypothesis. A reversible inhibition of the rate by added water was observed over Cs–SiO₂ and is attributed to migration and agglomeration of the cesium on the support in the presence of water.     

Oxidative dehydrogenation of ethylbenzene to styrene with CO2 over SnO2–ZrO2 mixed oxide nanocomposite catalysts

SnO₂–ZrO₂ nanocomposite catalysts with different compositions ranging from 0 to 100% of SnO₂ were prepared at room temperature by co-precipitation method using aqueous ammonia as a hydrolyzing agent. X-ray diffraction, transmission electron microscopic characterization revealed the SnO₂–ZrO₂ nanocomposite behavior. Acid–base properties of these catalysts were ascertained by temperature-programmed desorption (TPD) of NH₃ and CO₂. Both acidic and basic sites distribution of the nanocomposite catalysts is quite different from those of respective single oxides (SnO₂ or ZrO₂). Catalytic activity of these nanocomposite catalysts for ethylbenzene dehydrogenation (EBD) to styrene in the presence of excess CO₂ was evaluated. The change in the acid–base bi-functionality of the nanocomposite catalysts in comparison with single oxides had profound positive influence in enhancing the catalytic activity.     

纳米Zn/HZSM-5分子筛催化丙烷芳构化

采用低温老化、高温晶化两步法在Na2O-Al2O3-SiO2-四丙基氢氧化铵(TPAOH)-H2O体系中水热合成了纳米ZSM-5分子筛。用BET、N2吸/脱附曲线和NH3-TPD等手段对负载Zn的纳米HZSM-5分子筛结构和酸性进行了表征。结果表明,与微米Zn/HZSM-5分子筛催化剂相比,所制备的纳米Zn/HZSM-5催化剂比表面积明显增大,总酸量和弱酸量增加;在丙烷芳构化反应中,纳米Zn/HZSM-5分子筛具有更佳的催化活性、稳定性和芳烃选择性。