Synthesis and characterization of dl-thioctic acid (DLTA)-Fe3O4 nanocomposite

dl-Thioctic acid (DLTA) coated magnetite (Fe₃O₄) NP's have been prepared by the co-precipitation of iron oxide in the presence of DLTA. The product identified as magnetite, which has an average crystallite size of 7 ± 2 nm as estimated from X-ray line profile fitting. Particle size was estimated as 11 ± 1 nm from TEM micrographs. FT-IR analysis showed that the binding of DLTA on the surface of iron oxide is through carboxyl group is bidentate. VSM analysis explained the super-paramagnetic nature of the nanocomposite. TG analysis showed that the 80% of the nanocomposite was DLTA and 10% was Fe₃O₄, respectively. The conductivity measurements displayed the magnetic transition at ∼60 °C for DLTA-Fe₃O₄ NPs. Analysis of the conductivities reveals the fact that the a.c. conductivity shows a frequency-dependent behavior while d.c. electrical conductivity is strongly temperature dependent and is classified into two regions over a limited temperature range of up to 120 °C. Toxicity was tested measured by LDH assay.     

Synthesis and characteristics of poly(3-pyrrol-1-ylpropanoic acid) (PPyAA)-Fe3O4 nanocomposite

Poly(3-pyrrol-1-ylpropanoic acid) (PPyAA)-Fe₃O₄ nanocomposite was successfully synthesized by an in situ polymerization of 1-(2-carboxyethyl) pyrrole in the presence of synthesized Fe₃O₄ nanoparticles. Evaluation of structural, morphological, electrical and magnetic properties of the nanocomposite was performed by XRD, FT-IR, TEM, TGA, magnetization and conductivity measurements, respectively. XRD analysis reveals the inorganic phase as Fe₃O₄ and TGA shows about 90 wt% loading of Fe₃O₄ in the nanocomposite. FT-IR analysis indicates a successful conjugation of Fe₃O₄ particles with polypyrrole acetic acid. Magnetization measurements show that polypyrrole acetic acid coating decreases the saturation magnetization of Fe₃O₄ significantly. This reduction has been explained by the pinning of the surface spins by the possible adsorption of non-magnetic ions during the polymerization process. The conductivity and dielectric permittivity measurements strongly depend on the thermally activated polarization mechanism and thermal transition of PPyAA in the nanocomposite structure. Large value of dielectric permittivity (?′) of the nanocomposite at lower frequency is attributed to the predominance of species like Fe²⁺ ions and grain boundary defects (interfacial polarization).     

Preparation and characteristics of Fe3O4@YVO4:Eu bifunctional magnetic-luminescent nanocomposites

A facile direct precipitation method has been developed for the synthesis of bifunctional magnetic-luminescent nanocomposites with Fe₃O₄ nanoparticles as the core and YVO₄:Eu³⁺ as the shell. Transmission electron microscopy (TEM) images revealed that the obtained bifunctional nanocomposites had a core-shell structure and a spherical morphology. The average size was ∼150 nm, and the thickness of the shell was ∼15 nm. The X-ray diffraction (XRD) patterns showed that a cubic spinel structure of Fe₃O₄ core and a tetragonal phase of YVO₄ shell were obtained. Fourier transform infrared (FT-IR) spectra confirmed that the YVO₄:Eu³⁺ had been successfully deposited on the surface of Fe₃O₄ nanoparticles. Photoluminescence (PL) spectra indicated that the nanocomposites displayed a strong red characteristic emission of Eu³⁺. Magnetic measurements showed that the obtained bifunctional nanocomposites exhibited superparamagnetic behavior at room temperature. Therefore, the bifunctional nanocomposites are expected to develop many potential applications in biomedical fields.     

Facile synthesis, magnetic and microwave absorption properties of Fe3O4/polypyrrole core/shell nanocomposite

Fe₃O₄/polypyrrole (PPy) core/shell nanocomposite, with Fe₃O₄ nanoparticle as core and PPy as shell, could be facilely synthesized via in situ chemical oxidative polymerization of pyrrole monomers on the surface of Fe₃O₄ nanoparticles. The results indicate that core/shell nanocomposite consists of Fe₃O₄ core with the mean diameter of 100 nm and adjacent PPy shell with a thickness of about 70 nm. The as-prepared Fe₃O₄/PPy core/shell nanocomposite exhibits a saturated magnetization of 20.1 emu/g and coercivity value of 368.3 Oe, respectively. The electromagnetic characteristics of Fe₃O₄/PPy core/shell nanocomposite were also investigated with a vector network analyzer in the 2-18 GHz range. The absorbing peak position moves to lower frequency with increasing the thicknesses of samples. The value of the minimum reflection loss is −22.4 dB at 12.9 GHz for Fe₃O₄/PPy core/shell nanocomposite with a thickness of 2.3 mm, and a broad peak with a bandwidth lower than −10 dB is about 5 GHz. Such strong absorption is attributed to better electromagnetic matching due to the existence of PPy and the special core/shell structure.     

Direct synthesis and characterization of mesoporous Fe3O4 through pyrolysis of ferric nitrate-ethylene glycol gel

Mesoporous magnetite (Fe₃O₄) was successfully synthesized on a large scale by direct pyrolysis of ferric nitrate-EG (EG = ethylene glycol) gel in a one-end closed horizontal tube furnace in the air without using any template, additions, and carrier gas. The as-synthesized mesoporous Fe₃O₄ were characterized by powder X-ray diffraction (XRD), infrared spectra (IR), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), Brunauer-Emmett-Teller (BET), Barrett-Joyner-Halenda (BJH), and thermal gravimetric analysis (TGA). Results from TEM showed that the as-obtained Fe₃O₄ has mesoporous structure formed by the loose agglomeration of nanoparticles with diameter of about 6 nm, which was also confirmed by small-angle XRD and nitrogen adsorption analysis. Furthermore, vibrating sample magnetometer (VSM) measurements indicated that the saturated magnetization of the as-obtained mesoporous Fe₃O₄ was ferromagnetic with the saturation magnetization (Ms) and coercivity (Hc) of 46 emu/g and 136 Oe, respectively. In addition, a possible growth mechanism of mesoporous Fe₃O₄ was also discussed.     

Preparation of Ni0.5Zn0.5Fe2O4/SiO2 nanocomposites and their adsorption of bovine serum albumin

The magnetic nanocomposites of (1 − x)Ni_0.5Zn_0.5Fe₂O₄/xSiO₂ (x = 0-0.2) were synthesized by the citrate-gel process and their absorption behavior of bovine serum albumin (BSA) was investigated by UV spectroscopy at room temperature. The gel precursor and resultant nanocomposites were characterized by FTIR, XRD, TEM and BET techniques. The results show that the single ferrite phase of Ni_0.5Zn_0.5Fe₂O₄ is formed at 400 °C, with high saturation magnetization and small coercivity. A porous, amorphous silica layer is located at the ferrite nanograin boundaries, with the silica content increasing from 0 to 0.20, the average grain size of Ni_0.5Zn_0.5Fe₂O₄ calcined at 400 °C reduced from about 18-8 nm. Consequently, the specific surface area of the nanocomposites ascends clearly with the increase of silica content, which is largely contributed by the increase in the thickness of the porous silica layer. The Ni_0.5Zn_0.5Fe₂O₄/SiO₂ nanocomposites demonstrate a better adsorption capability than the bare Ni_0.5Zn_0.5Fe₂O₄ nanoparticles for BSA. With the increase of the silica content from 0 to 0.05 and the specific surface area from about 49-57 m²/g, the BSA adsorption capability of the Ni_0.5Zn_0.5Fe₂O₄/SiO₂ nanocomposites calcined at 400 °C improve dramatically from 22 to 49 mg/g. However, with a further increase of the silica content from 0.05 to 0.2, the specific surface area increase from about 57-120 m²/g, the BSA adsorption for the nanocomposites remains around 49 mg/g, owing to the pores in the porous silica layer which are too small to let the BSA protein molecules in.     

Synthesis, characterization, magnetic and electrical properties of the novel conductive and magnetic Polyaniline/MgFe2O4 nanocomposite having the core-shell structure

Conductive and magnetic Polyaniline/MgFe₂O₄ nanocomposite was successfully synthesized in the form of core-shell via in situ chemical polymerization of aniline in the presence of MgFe₂O₄ nano-particles. X-ray powder diffraction of ferrites indicated that the structure of the core material is having the spinel structure, and demonstrated the formation of PAni/MgFe₂O₄ nanocomposite. XRD and TEM photographs showed that the particle's size of the MgFe₂O₄ core-material were around 30-35 nm before coating with Polyaniline, and grown up to 45 nm in the core-shell nanocomposite after coating. Although PAni has a relatively smaller electrical field coefficient than the core-shell nanocomposite, the resistivity of the core-shell material decreased, and hence its conductivity increased after a certain threshold voltage of 0.98 V equivalent to threshold electric field value equals 5.5 V cm⁻¹. The magnetic hysteresis loops investigated with VSM indicated that coating MgFe₂O₄ with Polyaniline has an healing effect which covers the ferrite surface defects, thus decreasing the magnetic surface anisotropy of ferrite particles leading to a decrease of the saturated magnetization (Ms) from 21.33 emu/g to 5.905 emu/g and a decrease of the coercivity (Hc) from 88.66 Oe to 81.6 Oe for MgFe₂O₄ and the core-shell nanocomposite respectively due to the amount of Polyaniline added. TGA and DTA revealed improved thermal stability of the core-shell nanocomposite with respect to that of Polyaniline due to the incorporation of ferrites. Raman spectroscopy confirmed TGA, DTA and XRD studies, and revealed that pure PAni is less stable than the corresponding core-shell nanocomposite with respect to molecular changes which might occur during heating at elevated temperatures. Moreover, Raman study confirmed the interfacial interaction between the core and the shell materials, and lead to an assumption about the presence of different conjugation chain lengths and types, such as the presence of the semi-quinones aside the quinone rings in the polymer chain, which showed different response upon heating the sample.     

Synthesis and characterization of MWCNTs/Co1−xZnxFe2O4 magnetic nanocomposites and their use in hydrogels

A novel magnetic nanocomposite of multiwalled carbon nanotubes (MWCNTs) decorated with Co_1−xZn_xFe₂O₄ nanocrystals was synthesized successfully by an effective solvothermal method. The as-prepared MWCNTs/Co_1−xZn_xFe₂O₄ magnetic nanocomposite was used for the functionalization of P/H hydrogels as a prototype of device to show the potential application of the nanocomposites. The nanocomposites were characterized by X-ray diffraction analysis, transmission electron microscopy and vibrating sample magnetometer. The results show that the saturation magnetization of the MWCNTs/Co_1−xZn_xFe₂O₄ magnetic nanocomposites increases with x when the Zn²⁺ content is less than 0.5, but decreases rapidly when the Zn²⁺ content is more than 0.5. The saturation magnetization as a function of Zn²⁺ substitution reaches a maximum value of 57.5 emu g⁻¹ for x = 0.5. The probable synthesis mechanism of these nanocomposites was described based on the experimental results.     

One-pot synthesis of polyaniline/Fe3O4 nanocomposites with magnetic and conductive behaviour. Catalytic effect of Fe3O4 nanoparticles

Polyaniline/Fe₃O₄ nanocomposites were prepared by a one-pot synthesis using N-(4-aminophenyl)aniline as the reagent, molecular oxygen or hydrogen peroxide as the oxidizing agents in the presence of Fe₃O₄ nanoparticles (NPs) in powder and ferrofluid form. Both magnetic NPs in powder and ferrofluid form showed similar catalytic behaviour. The catalytic effect is particularly evident when molecular oxygen was used as the oxidizing agent. However, concerning the morphological aspects, only the composites prepared in the presence of ferrofluid-type Fe₃O₄ NPs showed a preferential morphology of nanorods (between 30 and 110 nm in diameter). All the composites are superparamagnetic at room temperature but at low temperature they are in a blocked state. Inter-particle interactions significantly affect the magnetic properties of the composites. The electrical conductivity of the composites is about 10⁻² S cm⁻¹, in agreement with the values obtained for polyaniline prepared by chemical route. A mechanism of the nanorods formation is proposed.     

Synthesis and microwave absorbing properties of polyaniline/MnFe2O4 nanocomposite

Conductive polyaniline (PANi)-manganese ferrite (MnFe₂O₄) nanocomposites with core-shell structure were synthesized by in situ polymerization in the presence of dodecyl benzene sulfonic acid (DBSA) as the surfactant and dopant and ammonium persulfate (APS) as the oxidant. The structure and magnetic properties of manganese ferrite nanoparticles were measured by using powder X-ray diffraction (XRD) and vibrating sample magnetometer (VSM), respectively. Its morphology, microstructure and DC conductivity of the nanocomposite were characterized by scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR) and four-wire-technique, respectively. The microwave absorbing properties of the nanocomposite powders dispersing in resin acrylic coating with the coating thickness of 1_.4 mm were investigated by using vector network analyzers in the frequency range of 8-12 GHz. A minimum reflection loss of −15.3 dB was observed at 10.4 GHz.     

Photocatalytic performance of nano-photocatalyst from TiO2 and Fe2O3 by mechanochemical synthesis

Nano-particles of homogeneous solid solution between TiO₂ and Fe₂O₃ (up to 10 mol%) have been prepared by mechanochemical milling of TiO₂ and yellow Fe₂O₃/red Fe₂O₃/precipitated Fe (OH)₃ using a planetary ball mill. Such novel solid solution cannot be prepared by conventional co-precipitation technique. A preliminary investigation of photocatalytic activity of mixed oxide (TiO₂/Fe₂O₃) on photo-oxidation of different organic dyes like Rhodamine B (RB), Methyl orange (MO), Thymol blue (TB) and Bromocresol green (BG) under visible light (300-W Xe lamp; λ > 420 nm) showed that TiO₂ having 5 mol% of Fe₂O₃ (YFT1) is 3-5 times higher photoactive than that of P25 TiO₂. The XRD result did not show the peaks assigned to the Fe components (for example Fe₂O₃, Fe₃O₄, FeO₃, and Fe metal) on the external surface of the anatase structure in the Fe₂O₃/TiO₂ attained through mechanochemical treatment. This meant that Fe components were well incorporated into the TiO₂ anatase structure. The average crystallite size and particle size of YFT1 were found to be 12 nm and 30 ± 5 nm respectively measured from XRD and TEM conforming to nanodimensions. Together with the Fe component, they absorbed wavelength of above 387 nm. The band slightly shifted to the right without tail broadness, which was the UV absorption of Fe oxide in the Fe₂O₃/TiO₂ particle attained through mechanochemical method. This meant that Fe components were well inserted into the framework of the TiO₂ anatase structure. EPR and magnetic susceptibility show that Fe³⁺ is in low spin state corresponding to μ_B = 1.8 BM. The temperature variation of μ_B shows that Fe³⁺ is well separated from each other and does not have any antiferromagnetic or ferromagnetic interaction. The evidence of Fe³⁺ in TiO₂/Fe₂O₃ alloy is also proved by a new method that is redox titration which is again support by the XPS spectrum.     

Influence of imidazolium-based ionic liquids on the performance of polyaniline-CoFe2O4 nanocomposites

Using cobalt ferrite (CoFe₂O₄) nanoparticles of different content as nucleation sites, polyaniline-CoFe₂O₄ nanofiber composites were successfully synthesized at the interface of water and ionic liquid via in-situ polymerization. Structure and morphology were investigated by TGA, TEM, XRD, and FT-IR. The influence of ionic liquids on the structure, conductivity and magnetic property of polyaniline-CoFe₂O₄ nanocomposites were studied in detail. The results show that imidazolium-based ionic liquids BMIPF₆ acts as an anchor agent during the nanofiber composites formation process. Introduction of ionic liquids obviously improves the conductivity but weakens the magnetization of polyaniline-CoFe₂O₄ nanocomposites in the same [CoFe₂O₄]/[An] ratio.     

Direct synthesis of Fe3O4 nanopowder by thermal decomposition of Fe-urea complex and its properties

An easy synthesis route of magnetite (Fe₃O₄) nanopowder is developed by using thermal decomposition of Fe-urea complex ([Fe(CON₂H₄)₆](NO₃)₃). The formation of Fe₃O₄ is confirmed from X-ray powder diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) measurements. The morphological properties and magnetic properties of the Fe₃O₄ are characterized by transmission electron microscopy (TEM) and magnetic measurements, respectively. By an increase in reaction temperature from 200 to 300 °C, the average crystallite size of the Fe₃O₄ nanopowder increases from 37 to 50 nm. Room temperature magnetization hysteresis curves show that the Fe₃O₄ nanopowder possesses ferrimagnetic characteristics. The saturation magnetization of the Fe₃O₄ nanopowder increases from 70.7 to 89.1 emu/g when the reaction temperature increases from 200 to 300 °C.     

Luminescent and magnetic properties of YVO4:Ln@Fe3O4 (Ln = Eu or Dy) nanocomposites

A series of core-shell bifunctional magnetic-optical YVO₄:Ln³⁺@Fe₃O₄ (Ln³⁺ = Eu³⁺ or Dy³⁺) nanocomposites have been successfully synthesized via two-step method. The nanocomposites have the advantage of high magnetic responsive and unique luminescence properties. The structure, luminescent and magnetic properties of the nanocomposites were investigated by XRD, TEM, PL and VSM. The maximum emission peaks of the nanocomposites are at 618 nm (doping Eu³⁺), 574 nm (doping Dy³⁺). The special saturation magnetization of the nanocomposites is 54 emu/g. The diameter of the nanocomposites is 400-900 nm.     

Electromagnetic composite films based on polypyrrole hydro-sponge and Fe3O4 ferrofluid

The preparation of free-standing electromagnetic composite films based on conductive polypyrrole (PPy) hydro-sponge and the Fe₃O₄ ferrofluid have been successfully accomplished via self-assembly in the presence of β-cyclodextrin sulfate and under static condition. Transmission electron microscope (TEM), scanning electron microscope (SEM) and X-ray diffraction (XRD) are used to study the morphology of the PPy-Fe₃O₄ composite. Structural characterizations by Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) have proved the interactions between Fe₃O₄ and PPy chains. As-prepared films possess high electrical conductivity, remarkable magnetic response as well as appropriate flexility. Both the conductivity and magnetization of the composite, the latter in particular, depend strongly on the Fe₃O₄ content and thus can be optimized by adjusting the relative content of Fe₃O₄ in the composite. The combination of both magnetic and conducting activities of the resulting composite makes it be a potential candidate as functional material in electromagnetic devices, such as magnetic-controlled switches.     

Ultrasonic-assisted in situ synthesis and characterization of superparamagnetic Fe3O4 nanoparticles

Superparamagnetic Fe₃O₄ nanoparticles were synthesized via a modified coprecipitation method, and were characterized with X-ray diffraction (XRD), vibrating sample magnetometer (VSM), Zeta potential and FT-IR, respectively. The influences of different kinds of surfactants (sodium dodecyl benzene sulfonate, polyethyleneglycol, oleic acid and dextran), temperatures and pH values on the grain size and properties were also investigated. In this method, Fe³⁺ was used as the only Fe source and partially reduced to Fe²⁺ by the reducing agent with precise content. The following reaction between Fe³⁺, Fe²⁺ and hydroxide radical brought pure Fe₃O₄ nanoparticles. The tiny fresh nanoparticles were coated in situ with surfactant under the action of sonication. Comparing with uncoated sample, the mean grain size and saturation magnetization of coated Fe₃O₄ nanoparticles decrease from 18.4 nm to 5.9-9.0 nm, and from 63.89 emu g⁻¹ to 52-58 emu g⁻¹ respectively. When oleic was used as the surfactant, the mean grain size of Fe₃O₄ nanoparticles firstly decreases with the increase of reaction temperature, but when the temperature is exceed to 80 °C, the continuous increase of temperature resulted in larger nanoparticles. the grain size decreases gradually with the increasing of pH values, and it remains unchanged when the PH value is up to 11. The saturation magnetization of as-prepared Fe₃O₄ nanoparticles always decreases with the fall of grain size.     

Synthesis,characterization, electrical transport and magnetic properties of PEDOT–DBSA–Fe3O4 conducting nanocomposite

Electrical transport and magnetic properties of newly synthesized conducting polymer nanocomposites involving poly(3,4-ethylenedioxythiophene) (PEDOT) and Fe₃O₄ nanoparticles are studied. Nanocomposite samples of varying proportions of inorganic to organic components were synthesized by adding EDOT monomer stabilized in miceller solution of DBSA (dodecylbenzene sulphonic acid) to aqueous colloidal dispersion of Fe₃O₄ nanoparticles, followed by oxidative polymerization using ammonium peroxodisulphate (APS). Transmission electron microscopic (TEM) photographs show presence of distinct spherical Fe₃O₄ naonparticles having diameter range of 20–40 nm and they are incorporated within the polymer chain in the nanocomposite samples. Temperature-dependent DC conductivity analysis indicates a smooth cross-over of the charge conduction from the high temperature 3D Mott's variable range hopping (VRH) mechanism to the 2D ES (Efros and Shklovoskii)-VRH behaviour at low temperature. Temperature-dependent DC magnetization studies reveal enhancement of blocking temperature (T_B) in the nanocomposite samples compared to that of bare Fe₃O₄ nanoparticles. Core shell morphology of the nanoparticles seems to be the cause for lowering the value of saturation magnetization of the Fe₃O₄ nanoparticles. Estimated magnetic domain sizes are comparable to those of grain sizes for the nanocomposite samples having lower content of nanoparticles (P₅₀ and P₁₀₀). Temperature-dependent AC-susceptibility data also supports the superparamagnetic behaviour.     

Mechanochemical synthesis of Al2O3-TiB2 nanocomposite powder from Al-TiO2-H3BO3 mixture

Alumina-titanium diboride nanocomposite (Al₂O₃-TiB₂) was produced using mixtures of titanium dioxide, acid boric and pure aluminum as raw materials via mechanochemical process. The phase transformation and structural characterization during mechanochemical process were utilized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analyses (TG-DTA) techniques. A thermodynamic appraisal showed that the reaction between TiO₂, B₂O₃ and Al is highly exothermic and should be self-sustaining. XRD analyses exhibited that the Al₂O₃-TiB₂ nanocomposite was formed after 1.5 h milling time. The results indicate that increasing milling time up to 40 h had no significant effect other than refining the crystallite size.     

Compressive strength, hardness and fracture toughness of Al2O3 whiskers reinforced ZTA and ATZ nanocomposites: Weibull analysis

The aim of this investigation was to study the variability in compressive strength, fracture toughness and microhardness applying the well-known Weibull statistics and to be able to provide a wide spectrum of mechanical properties in Al₂O₃ whisker reinforced alumina toughened zirconia (ATZ) and zirconia toughened alumina (ZTA) nanocomposites for possible dental applications. Uniaxial compression tests at room temperature of samples 6.35 ± 0.03 mm in diameter and 12.50 ± 0.63 mm in length and Vickers hardness measurements on polished surfaces were carried out. The indentation fracture toughness (K_IC) was derived from the average crack length. Weibull analysis was performed on the data. The ATZ2 (18.0 wt.% Al₂O₃ + 2.0 wt.%_(w) + 80.0 wt.% ZrO₂ (TZ-3Y)) nanocomposite reported the highest average compressive load of 1200 MPa, the highest value of characteristic strength, σ_o, of 1340 MPa with Weibull modulus of 3.25 and relatively high fracture toughness (4.7 ± 0.7 MPa m^1/2), suggesting that with the wide range of mechanical properties obtained in our work, different dental applications could be offered without lead to premature failure.     

Electrical and magnetic properties of the Fe3O4–polyaniline nanocomposite pellets containing DBSA-doped polyaniline and HCl-doped polyaniline with Fe3O4 nanoparticles

DBSA-doped polyaniline (DBSA–PANI) powder and HCl-doped polyaniline with Fe₃O₄ nanoparticles (HCl–PANI–Fe₃O₄) powder were mechanically mixed to obtain the Fe₃O₄–polyaniline nanocomposites. Powders of the nanocomposites were pressed to the pellets. Micromorphology, electrical and magnetic properties of the nanocomposite pellets were studied by using scanning electron microscopy and by measuring the conductivity in 100–300 K and the magnetization curve at room temperature. The DBSA–PANI pellets consist of long fibrils while the HCl–PANI–Fe₃O₄ pellets consist of granular particles. Thus the Fe₃O₄–polyaniline nanocomposites pellets consist of long fibrils and granular particles. The conductivity of the nanocomposite pellets linearly decreases from 0.19 ± 0.06 to 0.05 ± 0.01 S/cm when the HCl–PANI–Fe₃O₄ content increases from 0 to 100 wt.%. The variation of conductivity with temperature reveals that the charge transport mechanism can be considered to be one-dimensional variable-range-hopping (1D-VRH). All the Fe₃O₄–polyaniline nanocomposites show the magnetization curves. The saturation magnetization monotonously increases with increasing HCl–PANI–Fe₃O₄ content while the coercivity is estimated to be about zero independent of the HCl–PANI–Fe₃O₄ content. The saturation magnetization of the HCl–PANI–Fe₃O₄ is 11 emu/g.