Crystal structure and dielectric properties of La(Mg1−xZnx)1/2Ti1/2O3 ceramics at microwave frequencies

Ceramics in the system La(Mg_1−xZn_x)_1/2Ti_1/2O₃ with B₂O₃ additions (1 wt.%) have been investigated by the conventional solid-state route. The XRD patterns of the sintered samples (0.3 ≤ x ≤ 1.0) revealed single phase formation with a structure. The unit cell volume slightly increased with increasing Zn content (x). La(Mg_1−xZn_x)_1/2Ti_1/2O₃ were found to form perovskite solid solutions in the whole compositional range. The maximum values of the dielectric constant and the quality factor multiples resonant frequency (Q × f) can be obtained when the La(Mg_0.7Zn_0.3)_1/2Ti_1/2O₃ with 0.5 wt.% B₂O₃ additive were sintered at 1475 °C for 4 h. The temperature coefficient of resonant frequency τ_f (−63 ppm/°C) was measured for x = 0.7.     

Structure and dielectric characterization of xNd(Mg1/2Ti1/2)O3-(1 − x)Ca0.6La0.8/3TiO3 in the microwave frequency range

The crystal structures, phase compositions and the microwave dielectric properties of the xLa(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.8Sr_0.2TiO₃ composites prepared by the conventional solid state route have been investigated. The formation of solid solution is confirmed by the XRD patterns. Doping with B₂O₃ (0.5 wt.%) can effectively promote the densification and the dielectric properties of xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics. It is found that xNd(Mg_1/2Ti_1/2)O₃-(1 − x)Ca_0.6La_0.8/3TiO₃ ceramics can be sintered at 1375 °C, due to the liquid phase effect of B₂O₃ addition observed by Scanning Electronic Microscopy. At 1375 °C, 0.4Nd(Mg_1/2Ti_1/2)O₃-0.6Ca_0.6La_0.8/3TiO₃ ceramics with 1 wt.% B₂O₃ addition possesses a dielectric constant (?_r) of 49, a Q × f value of 13,000 (at 8 GHz) and a temperature coefficients of resonant frequency (τ_f) of 1 ppm/°C. As the content of Nd(Mg_1/2Ti_1/2)O₃ increases, the highest Q × f value of 20,000 GHz for x = 0.9 is achieved at the sintering temperature 1400 °C.     

Phase evolution and microwave dielectric properties of TiO2-modified (Mg0.95Co0.05)2TiO4 ceramics

Phase evolution and microwave dielectric properties of (1 − x)(Mg_0.95Co_0.05)₂TiO₄-xTiO₂ (x = 0-1) ceramics prepared by the conventional mixed oxide route have been investigated. Increasing the TiO₂ content would lead to a main phase transformation from (Mg_0.95Co_0.05)₂TiO₄ to (Mg_0.95Co_0.05)TiO₃, (Mg_0.95Co_0.05)Ti₂O₅ and then TiO₂. Not only did the TiO₂ addition compensate the τ_f, it also lowered the sintering temperature of specimen. A huge drop of Q × f occurs at a 40-60 mol% TiO₂ addition was attributed to the formation of (Mg_0.95Co_0.05)Ti₂O₅ phase. Specimen with x = 0.78 can possess an excellent combination of microwave dielectric properties: ?_r ∼ 24.77, Q × f ∼ 38,500 GHz and τ_f ∼ −1.3 ppm/°C.     

Microwave dielectric properties of temperature stable Li2ZnxCo1−xTi3O8 ceramics

The Li₂Zn_xCo_1−xTi₃O₈ (x = 0.2-0.8) solid solution system has been synthesized by the conventional solid-state ceramic route and the effect of Zn substitution for Co on microwave dielectric properties of Li₂CoTi₃O₈ ceramics has also been investigated. The microwave dielectric properties of these ceramics show a linear variation between the end members for all compositions. The optimized sintering temperatures of Li₂Zn_xCo_1−xTi₃O₈ ceramics increase with increasing content of Zn. The specimen with x = 0.4 sintered at 1050 °C/2 h exhibits an excellent combination of microwave dielectric properties with ?_r = 27.7, Q_u × f = 57,100 GHz and τ_f = −1.0 ppm/°C.     

High-dielectric-constant and low-loss microwave dielectric in the (1 − x)La(Mg0.5Ti0.5)O3-x(Ca0.8Sr0.2)TiO3 solid solution system

The microwave dielectric properties and microstructures of (1 − x)La(Mg_0.5Ti_0.5)O₃-x(Ca_0.8Sr_0.2)TiO₃ ceramics, prepared by a mixed oxide route, have been investigated. The forming of solid solutions was confirmed by the XRD patterns and the measured lattice parameters for all compositions. A near zero τ_f was achieved for samples with x = 0.5, although the dielectric properties varied with sintering temperature. The Q × f value of 0.5La(Mg_0.5Ti_0.5)O₃-0.5(Ca_0.8Sr_0.2)TiO₃ increased up to 1475 °C, after which it decreased. The decrease in dielectric properties was coincident with the onset of rapid grain growth. The optimum combination of microwave dielectric properties was achieved at 1475 °C for samples where x = 0.5 with a dielectric constant ?_r of 47.12, a Q × f value of 35,000 GHz (measured at 6.2 GHz) and a τ_f value of −4.7 ppm/°C.     

Crystal structure and dielectric properties of La(Mg0.5Ti0.5)O3-Ca0.8Sm0.4/3TiO3 solid solution system at microwave frequencies

The crystal structure and the dielectric properties of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ ceramics have been investigated. Ca_0.8Sm_0.4/3TiO₃ was employed as a τ_f compensator and was added to La(Mg_0.5Ti_0.5)O₃ to achieve a temperature-stable material. The formation of (1 − x)La(Mg_0.5Ti_0.5)O₃-xCa_0.8Sm_0.4/3TiO₃ solid solutions were confirmed by the XRD results and the measured lattice parameters for all compositions. The dielectric properties are strongly correlated to the sintering temperature and the compositional ratio of the specimens. Although the ?_r of the specimen could be boosted by increasing the amount of Ca_0.8Sm_0.4/3TiO₃, it would instead render a decrease in the Q × f. The τ_f value is strongly correlated to the compositions and can be controlled by the existing phases. A new microwave dielectric material 0.45La(Mg_0.5Ti_0.5)O₃-0.55Ca_0.8Sm_0.4/3TiO₃, possessing a fine combination of microwave dielectric properties with an ?_r of 47.83, a Q × f of 26,500 GHz (at 6.2 GHz) and a τ_f of −1.7 ppm/°C, is proposed as a very promising candidate material for today's 3G applications.     

Effect of CaTiO3 addition on microwave dielectric properties of Mg2(Ti0.95Sn0.05)O4 ceramics

The microwave dielectric properties of CaTiO₃-added Mg₂(Ti_0.95Sn_0.05)O₄ ceramics prepared by the mixed oxide route have been investigated. The combination of spinel-structured Mg₂(Ti_0.95Sn_0.05)O₄ and perovskite-structured CaTiO₃ forms a two-phase system (1 − x)Mg₂(Ti_0.95Sn_0.05)O₄-xCaTiO₃, which was confirmed by the XRD patterns and the EDX analysis and it also leads to a zero τ_f. The microwave dielectric properties of the ceramics can be effectively controlled by varying the x value. For practical applications, a new microwave dielectric material 0.91Mg₂(Ti_0.95Sn_0.05)O₄-0.09CaTiO₃ is suggested and it possesses a good combination of dielectric properties with an ?_r of ∼18.01, a Q × f of ∼92,000 GHz, and a τ_f of ∼0 ppm/°C, which makes it is a very promising candidate material for high frequency applications.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting Mg with Ni

The microwave dielectric properties of La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method at various sintering temperatures. The X-ray diffraction patterns of the La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.71 g/cm³, dielectric constant (?_r) of 20.19, quality factor (Q × f) of 74,600 GHz, and temperature coefficient of resonant frequency (τ_f) of −85 ppm/°C were obtained for La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Low temperature sintering and microwave dielectric properties of (Mg0.7Zn0.3)0.95Co0.05TiO3 ceramics with BaCu(B2O5) additions

The effects of BaCu(B₂O₅) additives on the sintering temperature and microwave dielectric properties of (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were investigated. The (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics were not able to be sintered below 1000 °C. However, when BaCu(B₂O₅) were added, they were sintered below 1000 °C and had the good microwave dielectric properties. It was suggested that a liquid phase with the composition of BaCu(B₂O₅) was formed during the sintering and assisted the densification of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics at low temperature. BaCu(B₂O₅) powders were produced and used to reduce the sintering temperature of the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics. Good microwave dielectric properties of Q × f = 35,000 GHz, ?_r = 18.5.0 and τ_f = −51 ppm/°C were obtained for the (Mg_0.7Zn_0.3)_0.95Co_0.05TiO₃ ceramics containing 7 wt.% mol% BaCu(B₂O₅) sintered at 950 °C for 4 h.     

High-Q microwave dielectrics in the (Mg1−xZnx)Al2O4 (x = 0-0.1) system

The microwave dielectric properties and the microstructures of (Mg_1−xZn_x)Al₂O₄ (x = 0-0.1) ceramic system prepared by the conventional solid-state route were investigated. The forming of spinel-structured (Mg_1−xZn_x)Al₂O₄ (x = 0-0.1) solid solutions was confirmed by the XRD patterns and the measured lattice parameters, which linearly varied from a = b = c = 8.0815 Å for MgAl₂O₄ to a = b = c= 8.0828 Å for (Mg_0.9Zn_0.1)Al₂O₄. By increasing x, the Q × f of (Mg_1−xZn_x)Al₂O₄ can be tremendously boosted from 82,000 GHz at x = 0 to a maximum of 156,000 GHz at x = 0.05. The Zn substitution was effective in reducing the dielectric loss without detrimental effects on the ?_r and τ_f values of the ceramics.     

Improving the piezoelectric thermal stability by tailoring phase transition behavior in the new (1 − x)[0.65PbMg1/3Nb2/3O3-0.35PbTiO3]-xBiZn1/2Ti1/2O3 perovskite solid solutions

The phase transition behavior and its effect on thermal stability of the piezoelectric properties of the (1 − x)[0.65PbMg_1/3Nb_2/3O₃-0.35PbTiO₃]-xBiZn_1/2Ti_1/2O₃ ceramics with 0 ≤ x ≤ 0.06 were investigated. The phase transition from the monoclinic to tetragonal phase was determined by the dielectric constant and elastic constant measurements. The temperature independent piezoelectric response with −d₃₁ = 188 pC/N was obtained from 175 to 337 K for the composition with x = 0.02. The enhanced thermal stability of piezoelectric response was achieved by shifting the monoclinic-tetragonal phase transition to the lower temperature.     

Reaction-sintering method for ultra-low loss (Mg0.95Co0.05)TiO3 ceramics

Microwave dielectric properties and microstructures of (Mg_0.95Co_0.05)TiO₃ ceramics prepared by a new sintering method (reaction-sintering method) were investigated. A pure phase of (Mg_0.95Co_0.05)TiO₃ was obtained by the new method and excellent dielectric properties were observed due to uniformities of the microstructure and the phase. In contrast, the secondary phase (Mg_0.95Co_0.05)Ti₂O₅ was observed in samples prepared by conventional sintering method. In order to study the influence of secondary phase on the microwave dielectric properties quantitatively, the weight fraction of (Mg_0.95Co_0.05)Ti₂O₅ was calculated on the basis of Rietveld refinement. The pore-free?_r values of specimens prepared by two different methods indicated that porosity plays an important role in the ?_r values of (Mg_0.95Co_0.05)TiO₃ ceramics. Specimens sintered by reaction-sintering method at 1350 °C for 4 h possess excellent dielectric properties with an ?_r of 16.3, a Q × f value of 244,500 GHz, and a τ_f value of −53.5 ppm/°C.     

Effect of addition of Ba(W0.5Cu0.5)O3 in Pb(Mg1/3Nb2/3)O3-Pb(Zn1/3Nb2/3)O3-Pb(Zr0.52Ti0.48)O3 ceramics on the sintering temperature, electrical properties and phase transition

In this work, we report on the Pb(Mg_1/3Nb_2/3)O₃-Pb(Zn_1/3Nb_2/3)O₃-Pb(Zr_0.52Ti_0.48)O₃ (PMN-PZN-PZT) ceramics with Ba(W_0.5Cu_0.5)O₃ as the sintering aid that was manufactured in order to develop the low-temperature sintering materials for piezoelectric device applications. The phase transition, microstructure, dielectric, piezoelectric properties, and the temperature stability of the ceramics were investigated. The results showed that the addition of Ba(W_0.5Cu_0.5)O₃ significantly improved the sintering temperature of PMN-PZN-PZT ceramics and could lower the sintering temperature from 1005 to 920 °C. Besides, the obtained Ba(W_0.5Cu_0.5)O₃-doped ceramics sintered at 920 °C have optimized electrical properties, which are listed as follows: (K_p = 0.63, Q_m = 1415 and d₃₃ = 351 pC/N), and high depolarization temperature above 320 °C. These results indicated that this material was a promising candidate for high-power multilayer piezoelectric device applications.     

Origin of giant dielectric constant in Ba[(Fe1−xCox)1/2Nb1/2]O3

The X-ray diffraction Rietveld refinement of Ba[(Fe_1−xCo_x)_1/2Nb_1/2]O₃ with 0 ≤ X ≤ 1 shows cubic structure formation with space group P_m3_m. No distinct tilting of oxygen octahedron is observed. The dielectric measurement of such a cubic system exhibited giant values (?′ > 10⁴) in the temperature range of 298-483 K and frequency range of 10²-10⁵ Hz. An analysis of the permittivity, electric modulus, and electrical conductivity properties in these systems confirmed the presence of oxygen vacancies induced dipolar relaxation. Our investigations show that the observed extremely high dielectric constant values are predominantly the result of oxygen vacancies induced dipoles produced at the grain boundaries. Additional significant intrinsic contributions to the permittivity comes from the directly doped electrons at the unit cell, as indicated by the enhancement in the observed values of the permittivity on replacement of Fe³⁺ (3d⁵) by Co³⁺ (3d⁶). The contributions of the doped free charges and the oxygen vacancy induced dipoles are separated using the Jump Relaxation Model.     

Fabrication and properties of Ba(Zr1−xCex)0.9Y0.1O2.95/NaCl composite electrolyte materials

Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95/NaCl (x = 0.1, 0.2 and 0.3) composite electrolyte materials were fabricated with ZnO as sintering aid. The effect of ZnO on the properties of Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95 matrix were investigated. The phase composition and microstructure of samples were characterized by XRD and SEM, respectively. The electrochemical performances were studied by three-probe conductivity measurement and AC impedance spectroscopy. XRD results showed that Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95 with 2 mol% of ZnO was perovskite structure. The relative density of this sample was above 95% when sintered at 1450 °C for 6 h. By adding 10 mol% of NaCl to Ba(Zr_1−xCe_x)_0.9Y_0.1O_2.95 with 2 mol% of ZnO that was sintered at 1400 °C for 6 h, the conductivity was increased. The electrical conductivity of 1.26 × 10⁻² S/cm and activation energy of 0.23 eV were obtained when tested at 800 °C in wet hydrogen.     

Sintering behaviors, magnetic and electric properties of Bi-Zn co-doped Co2Y ferrites

The Bi and Zn substitution effects on the sintering behaviors, magnetic and electric properties of hexagonal ferrites with a composition of 2(Ba_1−xBi_xO)·2(Zn_yCo_0.8−yCu_0.2O)·6(Fe_2−x/3Zn_x/3O₃) were investigated. The results showed that the addition of Bi and Zn can significantly promote Co₂Y densification. The Y phase may be triggered to decompose into M and spinel phases at high sintering temperatures (above 1050 °C) for samples with excess Bi (x = 0.2) substitution, which resulted in densification and magnetic properties degradation. Co₂Y ferrites with x = 0.1 and y = 0.4 sintered at 1050 °C show a relative density of 94%, a high initial permeability of 4.5, a quality factor (Q) of 50.     

Properties of praseodymium-doped bismuth potassium titanate (Bi0.5K0.5TiO3) synthesised using the soft combustion technique

Bismuth potassium titanate (Bi_0.5K_0.5TiO₃; BKT) and praseodymium-doped BKT (Bi_0.5(1−x)Pr_xK_0.5TiO₃; BPKT) powders were synthesised using the soft combustion technique. Fine particles of 10-100 nm of BKT and BPKT were produced. A single phase BKT was obtained with a minimum of 0.5 mol of glycine. Various compounds of Bi_0.5(1−x)Pr_xK_0.5TiO₃ where x = 0.01, 0.03, 0.05, 0.10, 0.15 and 0.20 were prepared. Pure BKT and BPKT powders were obtained after calcination at 800 °C for 3 h. After sintering at 1050 °C for 5 h, pure BKT and BPKT pellets were obtained for x = 0 and 0.01. However, for BPKT with x = 0.03, 0.05, 0.10, 0.15 and 0.20, a minor amount of Bi₄Ti₃O₁₂ (BIT) secondary phase was present after sintering at 1050 °C for 5 h. The crystallite size and grain size of all the samples followed similar trends, first increasing from x = 0 (undoped BKT) to x = 0.05 and then decreasing above x = 0.05. Among the undoped and doped samples, BPKT with x = 0.05 had the highest dielectric properties (?_r = 713.87) due to its large crystallite size (68.66 nm), large grain size (∼435 nm) and high relative density (93.39%).     

Mg-substituted ZnNb2O6-TiO2 composite ceramics for RF/microwaves ceramic capacitors

Microstructure and microwave dielectric properties of Mg-substituted ZnNb₂O₆-TiO₂ microwave ceramics were investigated. Mg acted as a grain refining reagent and columbite phase stabilization reagent. With an increasing Mg content, the amount of ixiolite (Zn, Mg) TiNb₂O₈ decreased, and the amount of (Zn_0.9Mg_0.1)_0.17Nb_0.33Ti_0.5O₂ and columbite increased. ZnO-Nb₂O₅-1.75TiO₂-5 mol.%MgO exhibited excellent dielectric properties (at 950 °C): ?_r = 35.6, Q × f = 16,000 GHz (at 5.6 GHz) and τ_f = −10 ppm/°C. The material was applied successfully to make RF/microwaves ceramic capacitor, whose self-resonance frequency was 19 GHz at low capacitance of 0.13 pF.     

High permittivity and low dielectric loss of the Ca1−xSrxCu3Ti4O12 ceramics

The Ca_1−xSr_xCu₃Ti₄O₁₂ (CSCTO) giant dielectric ceramics were prepared by conventional solid-state method. X-ray diffraction patterns revealed that a small amount of Sr²⁺ (x < 0.2) had no obvious effect on the phase structure of the CSCTO ceramics, while with increasing the Sr²⁺ content, a second phase of SrTiO₃ appeared. Electrical properties of CSCTO ceramics greatly depended on the Sr²⁺ content. The Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics exhibited a higher permittivity (71,153) and lower dielectric loss (0.022) when measured at 1 kHz at room temperature. The ceramics also performed good temperature stability in the temperature range from −50 °C to 100 °C at 1 kHz. By impedance spectroscopy analysis, all compounds were found to be electrically heterogeneous, showing semiconducting grains and insulating grain boundaries. The grain resistance was 1.28 Ω and the grain boundary resistance was 1.31 × 10⁵ Ω. All the results indicated that the Ca_0.9Sr_0.1Cu₃Ti₄O₁₂ ceramics were very promising materials with higher permittivity for practical applications.     

Dielectric and microwave properties of ZrO2 doped CaO-SiO2-B2O3 ceramic matrix composites

The behavior of dielectric and microwave properties against sintering temperature has been carried out on CaO-SiO₂-B₂O₃ ceramic matrix composites with ZrO₂ addition. The results indicated that ZrO₂ addition was advantageous to improve the dielectric and microwave properties. X-ray diffraction (XRD) patterns show that the major crystalline β-CaSiO₃ and a little SiO₂ phase existed at the temperature ranging from 950 °C to 1050 °C. At 0.5 wt% ZrO₂, CaO-SiO₂-B₂O₃ ceramic matrix composites sintered at 1000 °C possess good dielectric properties: ?_r = 5.85, tan δ = 1.59 × 10⁻⁴ (1 MHz) and excellent microwave properties: ?_r = 5.52, Q · f = 28,487 GHz (11.11 GHz). The permittivity of Zr-doped CaO-SiO₂-B₂O₃ ceramic matrix composites exhibited very little temperature dependence, which was less than ±2% over the temperature range of −50 to 150 °C. Moreover, the ZrO₂-doped CaO-SiO₂-B₂O₃ ceramic matrix composites have low permittivity below 5.5 over a wide frequency range from 20 Hz to 1 MHz.