Couplages entre sources imprimées actives Analyse ďun réseau fini à deux dimensions de sources plates actives Application au balayage électronique

Three kinds of mutual coupling between active printed antennas, due to respectively space waves, surface waves and feed line, are evaluated and expressed with analytical forms which are in good agreement with experiments. There are two problems associated when using thicker substrate to broaden the microstrip antenna bandwidth : increase in surface waves and coaxial line coupling effects, and deterioration of the radiation pattern. The solution to the problem is to make use of substrates with very low relative permittivity to put a Lecher-line instead of a coaxial line. The different couplings between all radiating elements have been taken into account to calculate the active impedance of the individual element and the perturbation of radiation characteristics for a scanned beam array at reception.     

探针馈电印刷线天线的矩量法分析——（Ⅰ）单臂天线

利用同轴内导体延和为探针对印刷天线进行直接馈电是一种易于实现的馈电方式。本文介绍了一种分析单臂探针馈电印刷线天线的数值方法,该方法是基于并矢格林函数和互易定量求解电流积分方程的矩量法,适合于分析任意形状印刷线天线,首先给出描述电流分布的积分方程及其矩量法求解公式,在解得电流分布基础上,应用驻相法计算远区辐射场,通过计算与实验比较,验证了分析方法和计算程序的正确性,最后对一圆极化开口印刷圆环天线进行分析计算,表明了方法的实用价值。     

超宽带平面天线技术

对近年来发展的超宽带平面天线技术进行了综述,依次介绍了超宽带平板单极天线、超宽带印刷单极天线和超宽带印刷缝隙天线的进展,并作了比较.最后也介绍了具有带阻功能的超宽带印刷天线..     

Geometric and Compaction Dependence of Printed Polymer-Based RFID Tag Antenna Performance

Radio frequency identification (RFID) tags with printed antennas are lower in cost but have lower performance than those with metal antennas. Printed antennas can replace metal ones if the performance is increased without raising cost. The performance of printed antennas can be increased if the series resistance in the antennas is lowered. The resistance is dependent on the line thickness and the resistivity of the conductive ink. Printed antennas with different line thicknesses were fabricated to investigate the effect of compaction and thickness on the resistance. The resistance of the printed antenna coils decreased by more than 40% after compaction, while the inductance and the parasitic capacitance were unchanged. RFIDs with compacted printed antennas were found to have significantly increased read range. RFIDs with thick printed antennas were fabricated and tested. These RFIDs were shown to have read ranges comparable to the RFIDs with copper wire antennas. Moreover, a geometry-independent plateau for the read range was found. The presence of a plateau is valuable for thick-line printed antenna since the plateau will enable the usage of low precision printing techniques to lower tag fabrication cost.     

Considerations for millimeter wave printed antennas

Calculated data are presented on the performance of printed antenna elements on substrates which may be electrically thick, as would be the case for printed antennas at millimeter wave frequencies. Printed dipoles and microstrip patch antennas on polytetrafluoroethylene (PTFE), quartz, and gallium arsenide substrates are considered. Data are given for resonant length, resonant resistance, bandwidth, loss due to surface waves, loss due to dielectric heating, and mutual coupling. Also presented is an optimization procedure for maximizing or minimizing power launched into surface waves from a multielement printed antenna array. The data are calculated by a moment method solution.     

Gain enhancement methods for printed circuit antennas through multiple superstrates

Reciprocity and a transmission line model are used to determine the radiation properties of printed circuit antennas (PCA's) in a multilayered material configuration. It is demonstrated that extremely high directive gain may result at any scan angle, with practical materials, if the thickness of the substrate and multiple superstrate layers is chosen properly. This model is also used to analyze the radiation characteristics of printed circuit antennas in inhomogeneous substrates.     

The Millimeter Wave Radiation of a Traveling Wave Sinusoidal Wire Antenna

In this paper, investigation of radiation properties of the traveling-wave sinusoidal wire antennas is extended to the millimeter-wave frequencies (Ka-band) for the antennas whose geometrical dimensions vary in a wide range. Far-field patterns and S-parameters of composed three antenna sets were measured. A mathematical model was constructed for the structure and a MATLAB code based on this theoretical approach was written to calculate patterns, phase and attenuation constants of all investigated antennas. Frequency characteristics and the relation of antenna dimensions with wave parameters were investigated. Measured and calculated patterns were also compared with the constructed far-field patterns obtained by MoM (method of moments) and the MoM current distributions were used to explain the loss mechanisms of antennas. A directive, undistorted and smooth radiation can be achieved only choosing small undulated antennas whose peak-to-peak amplitude to period ratio κ is smaller than 0.4 (κ?<?0.4). It is shown that wavelength of broadside radiation is not equal to antenna period for all antennas, except for very small undulated antennas (κ?<?0.2). This antenna type can be used as a frequency-scan antenna for millimeter wave radars.     

An efficient method to determine Green's functions of atwo-dimensional photonic crystal excited by a line source - thephased-array method

A novel and efficient method to determine Green's functions in photonic crystals (PCs), i.e., the phased-array method (PAM), is presented. The PAM is a combination of the plane-wave method and the array-scanning method, which is both more flexible and computationally faster than the eigenmodes expansion method. A complete derivation of the electric- and magnetic-field Green's functions associated, respectively, with an infinite electric and magnetic current line exciting a two-dimensional PC is given. Although the developments are presented only for a line source, the PAM can be extended to a dipole source. Thus, the PAM represents a promising method for the analysis of printed-circuit elements or antennas on PC materials. Numerical results for the Green's functions are shown for different positions of the source and a discussion about radiation patterns, asymptotic behaviors, and convergence characteristics is proposed     

Accurate characterization of planar printed antennas usingfinite-difference time-domain method

The finite-difference-time-domain method (FD-TD) is used to characterize complex planar printed antennas with various feed structures, which include coaxial probe feed, microstrip line feed, and aperture coupled feed structures. A coaxial probe model is developed by using a three-dimensional FD-TD technique. This model is shown to be an efficient and accurate tool for modeling coaxial line fed structures. A novel use of a dispersive absorbing boundary condition is presented for a printed antenna with a high dielectric constant. All the numerical results obtained by the FD-TD method are compared with experimental results, and the comparison shows excellent agreement over a wide frequency band     

New considerations in the design of microstrip antennas

Printed microstrip antennas and arrays are known to have limitations in terms of bandwidth and efficiency, all imposed by the very presence of the dielectric substrate. Microstrip arrays printed on a very thin film and separated from the ground-plane by foam were successfully designed; however, the fabrication difficulties associated with the use of foam considerably increases the fabrication cost. In this paper, a new concept is presented. Rather than using a superstrata geometry, the “printed circuit” is etched out of metal and supported at “strategic points” by (metallic or nonmetallic) posts. The main motivation for this work was to obtain large microstrip arrays, which exhibit a higher efficiency than conventional ones, and can be fabricated using inexpensive large quantity production techniques. However, this technology was also used to develop many new types of microstrip antennas. Microstrip elements and arrays based on this technology were designed and fabricated for the L, S, and C bands     

Moment-method analysis of printed circular wire-loop antenna usingcurved piecewise sinusoidal subdomain basis and test functions

A computationally efficient method for analyzing printed wire-loop antennas on grounded dielectric substrates which uses curved piecewise sinusoidal subdomain current basis and test functions spanning two segments in a moment-method solution to Pocklington's equation is presented. Results for loop-input impedances are convergent, and these, together with efficiencies, compare favorably with computations using entire domain and linear subdomain basis and test functions     

Analysis and size reduction of various printed monopoles withdifferent shapes

A simple analysis based on the transmission line model applied to printed dipole antennas, and the Babinet principle allows different shapes of printed monopole antennas to be easily optimised. A shortening ratio (ρ) of 48% (respectively 30%, 40%) is achieved for the monopole antenna by using a step change in line width (respectively a triangular monopole, and a line with a triangular cap). Theoretical input impedance of these various monopoles compare closely with experimental results     

Printed antenna and array with circular polarisation

A new type of printed antenna element, as well as an array of elements with circular polarisation, is shown. The antenna has a much wider bandwidth than known circularly polarised printed antennas, mostly microstrip patches. The method of design and realisation with experimental results is shown     

Compact multielement Marconi-Franklin type printed antennas for millimeter wireless systems

Two novel Marconi-Franklin type printed antenna arrays, each consisting of three radiating elements arranged in a cascade configuration, are investigated. Both antennas are printed on a single high permittivity dielectric substrate and fed by SMA connectors, although coplanar waveguide (CPW) feed could easily be applied to further allow easier integration into an RF chip module. Two constructed prototypes, suitable for local-multipoint-distribution service operation in the 26-GHz band (25.5-26.5 GHz), are demonstrated. The constructed prototypes show an impedance bandwidth of about 1 GHz and a maximum gain of more than 5 dBi, with small variations (<1.8 dBi), is obtained across the achieved impedance bandwidth. Details of theoretical and experimental results showing impedance and radiation characteristics for both prototype antennas are given and discussed.     

Aperture-coupled microstrip antenna with a perpendicular feed

A new technique is described for feeding printed antennas. A microstrip antenna on one substrate is coupled through an electrically small aperture to a microstrip feed line on a perpendicularly oriented substrate. No direct connection is made to the patch. Such a geometry allows two separate substrates to be used for the antenna and feed functions. Measurements of a prototype design are presented.     

Analysis of infinite arrays of substrate-supported metal stripantennas

An electric field integral equation method is applied to a metal strip antenna on an electrically thick dielectric substrate of finite size in a uniform infinite array environment. An efficient solution is found using the method of moments. Metal strip folded dipole antennas are analyzed both with and without a coplanar strip feed line, and the effects of the substrate and feed line are investigated. A technique for minimizing the effect of feed line scattering is presented, and arrays of these elements are shown to be capable of good scanning performance over a wide range of beam-steer angles. A phased array simulator experiment is described and the measured results show good agreement with those obtained by analysis. The class of antenna elements studied may be fabricated using monolithic microwave integrated circuit (MMIC) technology, and the analysis described illustrates the expected characteristics for millimeter-wavelength phased arrays of this type     

Efficient Design of Directive Patch Antennas in Mobile Communications Using Metamaterials

An efficient approach for designing directive patch antennas using metamaterials is presented. Based on the left-handed-material (LHM) transmission line model, circuit elements L and C of the LHM equivalent circuit model are computed in terms of the prescribed desirable characteristics of directive patch antennas. Formulae to calculate the LHM design parameters from the circuit elements L and C are developed. Design examples for the GSM900 and GSM1800 frequency bands in mobile communications are performed to illustrate validation and efficiency of this design approach.     

Printed ring slot antenna for circular polarization

A new design of a microstrip-line-fed circularly polarized printed ring slot antenna is proposed. Circular polarization (CP) radiation of the proposed design is achieved by introducing proper asymmetry in the ring slot structure and feeding the ring slot using a microstrip line at 45° from the introduced asymmetry. The asymmetry introduced in the proposed design is a meandered-slot section and the proposed CP design can be applied to printed square and annular ring slot antennas. Prototypes of the proposed design have been implemented. Experimental results show that good CP radiation performances are obtained and the 3 dB axial-ratio CP bandwidths obtained for the square and annular ring slot antennas are about 4.3% and 3.5%, respectively     

小型平面超宽带天线的研究进展

对小型平面超宽带(UWB)天线的研究现状进行了分析总结.首先介绍超宽带无线通信的技术背景,描述了超宽带天线的几种常见定义.然后分别对小型超宽带印刷单极子天线的设计、小型超宽带缝隙天线的设计、具有陷波功能的小型超宽带天线的设计进行了详细的评论,并讨论了超宽带天线的性能评价方法.最后展望了小型平面超宽带天线的未来研究方向.     

Design and performance analysis of side by side,echelon and H‐shaped multiple printed dipole antennas for wireless local area network application

An array of printed dipole antennas for wireless local area network applications is designed and simulated using ads software. In MIMO system, numbers of antenna elements are used in different configuration. This paper presents the simulated results of printed dipole antennas in side by side 4‐element array, echelon and H‐shaped dipole array configurations. The designed antenna is characterized by measuring return loss, radiation pattern, directivity, and gain and also presented the simulated capacity results of different array configurations. The mutual coupling between the dipoles of different orientations is included to make simulation more realistic. Copyright © 2013 John Wiley & Sons, Ltd.