Experimental study on combustion of torrefied palm kernel shell (PKS) in oxy‐fuel environment

Oxy‐combustion of biomass can be a major candidate to achieve negative emission of CO₂ from a pulverized fuel (pf)‐firing power generation plants. Understanding combustion behavior of biomass fuels in oxy‐firing conditions is a key for design of oxy‐combustion retrofit of pulverized fuel power plant. This study aims to investigate a lab‐scale combustion behavior of torrefied palm kernel shell (PKS) in oxy‐combustion environments in comparison with the reference bituminous coal. A 20 kW_th‐scale, down‐firing furnace was used to conduct the experiments using both air (conventional) and O₂/CO₂ (30 vol% for O₂) as an oxidant. A bituminous coal (Sebuku coal) was also combusted in both air‐ and oxy‐firing condition with the same conditions of oxidizers and thermal heat inputs. Distributions of gas temperature, unburned carbon, and NO_x concentration were measured through sampling of gases and particles along axial directions. Moreover, the concentrations of SO_x and HCl were measured at the exit of the furnace. Experimental results showed that burnout rate was enhanced during oxy‐fuel combustion. The unburnt carbon in the flue gas was reduced considerably (~75%) during combustion of torrefied PKS in oxy‐fuel environment as compared with air‐firing condition. In addition, NO emission was reduced by 16.5% during combustion of PKS in oxy‐fuel environment as compared with air‐firing condition.     

Frontiers in combustion techniques and burner designs for emissions control and CO2 capture: A review

The use of fossil fuel is expected to increase significantly by midcentury because of the large rise in the world energy demand despite the effective integration of renewable energies in the energy production sector. This increase, alongside with the development of stricter emission regulations, forced the manufacturers of combustion systems, especially gas turbines, to develop novel combustion techniques for the control of NO_x and CO₂ emissions, the latter being a greenhouse gas responsible for more than 60% to the global warming problem. The present review addresses different burner designs and combustion techniques for clean power production in gas turbines. Combustion and emission characteristics, flame instabilities, and solution techniques are presented, such as lean premixed air‐fuel (LPM) and premixed oxy‐fuel combustion techniques, and the combustor performance is compared for both cases. The fuel flexibility approach is also reviewed, as one of the combustion techniques for controlling emissions and reducing flame instabilities, focusing on the hydrogen‐enrichment and the integrated fuel‐flexible premixed oxy‐combustion approaches. State‐of‐the‐art burner designs for gas turbine combustion applications are reviewed in this study, including stagnation point reverse flow (SPRF) burner, dry low NO_x (DLN) and dry low‐emission (DLE) burners, EnVironmental burners (including EV, AEV, and SEV burners), perforated plate (PP) burner, and micromixer (MM) burner. Special emphasis is made on the MM combustor technology, as one of the most recent advances in gas turbines for stable premixed flame operation with wide turndown and effective control of NO_x emissions. Since the generation of pure oxygen is prerequisite to oxy‐combustion, oxygen‐separation membranes became of immense importance either for air separation for clean oxy‐combustion applications or for conversion/splitting of the effluent CO₂ into useful chemical and energy products. The different carbon‐capture technologies, along with the most recent carbon‐utilization approaches towards CO₂ emissions control, are also reviewed.     

Mechanism analysis on the pulverized coal combustion flame stability and NOx emission in a swirl burner with deep air staging

Low NOx burner and air staged combustion are widely applied to control NOx emission in coal-fired power plants. The gas-solid two-phase flow, pulverized coal combustion and NOx emission characteristics of a single low NOx swirl burner in an existing coal-fired boiler was numerically simulated to analyze the mechanisms of flame stability and in-flame NOx reduction. And the detailed NOx formation and reduction model under fuel rich conditions was employed to optimize NOx emissions for the low NOx burner with air staged combustion of different burner stoichiometric ratios. The results show that the specially-designed swirl burner structures including the pulverized coal concentrator, flame stabilizing ring and baffle plate create an ignition region of high gas temperature, proper oxygen concentration and high pulverized coal concentration near the annular recirculation zone at the burner outlet for flame stability. At the same time, the annular recirculation zone is generated between the primary and secondary air jets to promote the rapid ignition and combustion of pulverized coal particles to consume oxygen, and then a reducing region is formed as fuel-rich environment to contribute to in-flame NO_X reduction. Moreover, the NOx concentration at the outlet of the combustion chamber is greatly reduced when the deep air staged combustion with the burner stoichiometric ratio of 0.75 is adopted, and the CO concentration at the outlet of the combustion chamber can be maintained simultaneously at a low level through the over-fired air injection of high velocity to enhance the mixing of the fresh air with the flue gas, which can provide the optimal solution for lower NOx emission in the existing coal-fired boilers.     

Detailed investigation of a pulverized fuel swirl flame in CO2/O2 atmosphere

A novel approach to oxycoal flame stabilization has been developed at the Institute of Heat and Mass Transfer at RWTH Aachen University [D. Toporov, M. Förster, R. Kneer, in: Third Int. Conf. on Clean Coal Technologies for Our Future, Cagliari, Sardinia, Italy, 15-17 May 2007]. The swirl burner design and its operating conditions have been adjusted in order to enforce CO formation thus stabilizing the flame and obtaining a full burnout at levels of O₂ content in the O₂/CO₂ mixture similar to those in air. The paper presents results of detailed numerical and experimental investigations of a stable oxy-fired pulverized coal swirl flame (type-2) obtained with a 21 vol% O₂ concentration. The combustion tests were performed in a vertical pilot-scale furnace (100 kW_th) in the framework of the OXYCOAL-AC research project aiming to develop a membrane-based oxyfuel process. The experimental results concerning gas velocities, gas and particle temperatures, and gas compositions are presented and discussed, focusing on the underlying mechanisms as well as on the aerodynamics of the oxycoal flame. A comparison between measurements and simulations has shown the validity of the numerical method used. The reported data set can be used for validation of numerical models developed for prediction of oxyfuel combustion.     

惯性浓淡旋流燃烧器的原理及其在50t_h锅炉上的应用

在径向浓淡旋流煤粉燃烧器的基础上,本文提出了一种新型燃烧器－惯性浓淡旋流煤粉燃烧器,即在燃烧器一次风通道中加入煤粉浓缩器,并将其置于燃烧器喷口较近的位置,一次风粉经过煤粉浓缩器后,形成了由燃烧器中心向外煤粉浓度由高向低的分布趋势,依靠煤粉颗粒的惯性,将这种分布趋势一直保持到燃烧器出口。针对一台燃用烟煤的５０ｔ／ｈ煤粉炉的特点,给出了该燃烧器的布置,介绍了改造前后的运行情况。     

Experimental and numerical analysis of oxy‐fuel combustion in a porous plate reactor

The present work focuses on studying experimentally and numerically the oxy‐fuel combustion characteristics inside a porous plate reactor towards the application of oxy‐combustion carbon capture technology. Initially, non‐reactive flow experiments are performed to analyze the permeation rate of oxygen in order to obtain the desired stoichiometric ratios. A numerical model is developed for non‐reactive and reactive flow cases. The model is validated against the presently recorded experimental data for the non‐reacting flow cases, and it is validated against the available literature data for oxy‐fuel combustion for the reacting flow cases. A modified two‐step oxy‐combustion reaction kinetics model for methane is implemented in the present model. Simulations are performed over wide range of operating oxidizer ratios (O₂/CO₂ ratio), from OR = 0.2 to OR = 0.4, and over wide range of equivalence ratios, from φ = 0.7 to φ = 1.0. The flame length was decreased as a result of the increase of the oxidizer ratio. Effects of CO₂ recirculation amount on the oxy‐combustion flame stability are examined. A reduction in combustion temperature and increase in flame fluctuations are encountered while increasing CO₂ concentration inside the reactor. At high equivalence ratio, the combustion temperature and flame stability are improved. At low equivalence ratio, the flame length is increased, and the flame was moved towards the reactor center line. Copyright © 2015 John Wiley & Sons, Ltd.     

新型旋流煤粉燃烧器出口区域气固两相流场的PDPA实验研究

针对电站锅炉燃用煤种多变和负荷多变的问题,提出了一种新型的旋流燃烧技术,即利用在一次风管中加装浓缩煤粉构件实行煤粉浓淡分离的旋流浓淡煤粉燃烧器。使用三维相位多普勒颗粒分析仪对旋流浓淡煤粉燃烧器和双调风旋流煤粉燃烧器出口区域气固两相流场进行了实验研究,得出了两种不同燃烧器几何结构下的气固两相流场和颗粒浓度场,并进行了理论分析。     

Gas/particle flow and combustion characteristics and NOx emissions of a new swirl coal burner

Due to the limits of reserves and price for the high rank coal, the low rank coal has been employed as fuel for power generation in China and will be eventually employed in the world. To burn low rank coal, centrally fuel-rich swirl coal combustion burner has been studied in Harbin Institute of Technology. This paper reviews and analyzes the major research results. The work has included both experiments and numerical simulation. The experiments were conducted using small-scale single-phase experimental equipment, a gas/particle two-phase test facility and 200- and 300-MW_e wall-fired utility boilers. For the burner, the primary air and glass beads partially penetrate the central recirculation zone and are then deflected radially. At the center of the central recirculation zone, there is high particle volume flux and large particle size. For the burners the local mean CO concentrations, gas temperatures and temperature gradient are higher, and the mean concentrations of O₂ and NO_x in the jet flow direction in the burner region are lower. Moreover, the mean O₂ concentration is higher and the gas temperature and mean CO concentration are lower in the side wall region. Centrally fuel-rich burners have been successfully used in 200- and 300-MWe wall-fired pulverized coal utility boilers.     

旋流燃烧器的稳燃及其结构优化分析

简要论述了国内常见几种旋流燃烧器的稳燃措施;介绍了ABT公司新近推出的"弓形"低NOx燃烧器;最后,提出了旋流燃烧器结构优化的建议。     

煤粉直接点火燃烧器技术及其进展

煤粉直接点火燃烧器应是我国电站煤粉锅炉燃烧器改进的主要方向,提出把直接点火技术与稳燃技术结合设计直接点火燃烧器的思路,对该类燃烧器做了较合理的分类。指出了少油煤粉直接点火燃烧器及无油煤粉直接点火燃烧器两大系列燃烧器发展状况及存在的问题,并指出目前应大力开发无油煤粉直接点火系列燃烧器,对电站锅炉煤粉直接点火燃烧器的研究有指导意义。     

Experimental study of the combustion efficiency and formation of NOx in an industrial pulverized coal combustor

With horizontal bias combustion burners, experiments have been carried out on a 670 t h^?1, corner‐fired, pulverized‐coal fired boiler burning bituminous coal. At 200 MWe load, the furnace excess O₂ remains stable. The different horizontal fuel biases are obtained by changing the tilt angle of all the Louvre enrichers' regulating blades. The tilt angles of the blades are 0, 15, 24, 32°; the result is that the enriching ratios of the fuel‐rich primary air increase from 2.2 to 2.6 at No. 2 corner, and from 1.2 to 4.2 at No. 3 corner. The gas temperature increases in the burner region. The application of the horizontal bias combustion burners results in a reduction in NO_x formation from 545.7 mg Nm^?3 (O₂=6%) to 287.9 mg Nm^?3, and a substantial reduction in carbon in ash content from 5.24 to 2.48%. The boiler operated stably at a load of 80 MWe without auxiliary fuel oil. Copyright © 2004 John Wiley & Sons, Ltd.     

Combustion and emission characteristics of premixed biogas mixtures: An experimental study

In this study, effects of fuel composition, swirl number and hydrogen addition on combustion and emission characteristics of various biogas mixtures were experimentally investigated. To this end, a laboratory scale combustor and a swirl stabilized premixed burner were designed and manufactured. Later on, this combusting apparatus was equipped with flow, control, safety and measurement tools, hence entire test system was constituted. Combustion and emission characteristics of tested biogas mixtures were determined by measuring temperature and species (CO₂, CO, O₂ and NO) distributions throughout the combustion chamber. Additionally, flame structures of tested biogas mixtures were evaluated by examining flame luminosity, visible flame length and flame thickness from instantaneous flame images. Results of this study showed that both radial and axial temperature distribution variations of tested biogas mixtures differently alter with hydrogen addition based on the gas composition. Although flame temperature increases with swirl number at burner outlet, it presents a non-monotonous dependence on swirl number outside the flame region because of the modified flow characteristics. This is also the case for emissions of CO₂.     

Jet flames of a refuse derived fuel

This paper is concerned with combustion of a refuse derived fuel in a small-scale flame. The objective is to provide a direct comparison of the RDF flame properties with properties of pulverized coal flames fired under similar boundary conditions. Measurements of temperature, gas composition (O₂, CO₂, CO, NO) and burnout have demonstrated fundamental differences between the coal flames and the RDF flames. The pulverized coals ignite in the close vicinity of the burner and most of the combustion is completed within the first 300 ms. Despite the high volatile content of the RDF, its combustion extends far into the furnace and after 1.8 s residence time only a 94% burnout has been achieved. This effect has been attributed not only to the larger particle size of fluffy RDF particles but also to differences in RDF volatiles if compared to coal volatiles. Substantial amounts of oily tars have been observed in the RDF flames even though the flame temperatures exceeded 1300 °C. The presence of these tars has enhanced the slagging propensity of RDF flames and rapidly growing deposits of high carbon content have been observed.     

Hydrogen combustion characteristics in a model burner with a coaxial injector

We have developed a burner for a hydrogen combustion turbine and proposed two kinds of burners, in which the combustion region is separated from the mixing region and in the former H₂ and O₂ are burned in a slightly fuel-rich condition or a stoichiometric condition. We manufactured a small-scale, water-cooled model burner, made of oxygen-free copper, and with two pairs of transparent quartz windows for a flame observation. A coaxial type injector was employed, in which an inner tube (for oxygen) was set inside the recess of the outer tube (for hydrogen). The H₂-O₂ combustion characteristics were studied while changing such parameters as injection velocities, equivalence ratios, and swirl numbers adding to a O₂ flow. The stable combustion region ranged from ṁH₂ = 0.3–1.5 g/s and fr φ = 0.9–2.0. Then H₂-O₂ combustion characteristics in steam, N₂ and Ar were studied to get stable combustion conditions. As a result, we obtained the fundamental design materials for a hydrogen combustion turbine.     

Reactor performance with primary/secondary swirl intensity and direction in coal gasification process

In order to evaluate the effect of swirl direction and intensity of primary/secondary stream on pulverized coal gasification performance, a numerical study was conducted. Eulerian and Lagrangian approaches are used for the gas and solid phase, respectively. The computation code was formulated with PSI‐cell method, k–? model for turbulence flow, Monte‐Carlo method for radiative heat transfer, and eddy dissipation model for gas‐phase reaction rate. A one‐step two‐reaction model is employed for the devolatilization of Kideco coal. Flow and reactor performance are varied by primary/secondary swirl intensity and direction. For weak primary swirl, the WSF region is minimized at the secondary vane angle beginning generation of internal recirculation zone and having peak coal burnout. The flame stability is improved at counterswirl rather than coswirl due to its intense shear. Meanwhile, for strong primary swirl, flow distribution and coal burnout are the reverse trend with those of weak swirl and the flame stability is somewhat enhanced at coswirl rather than counterswirl. To improve coal burnout and flame stability, it is confirmed that the swirl condition be proposed for moving the flame front position toward upstream. Copyright © 2001 John Wiley & Sons, Ltd.     

Influence of primary air ratio on flow and combustion characteristics and NOx emissions of a new swirl coal burner

Cold airflow experiments on a small-scale burner model, as well as in situ experiments on a centrally fuel-rich swirl coal combustion burner were conducted. Measurements were taken from within a 300 MW_e wall-fired pulverized-coal utility boiler installed with eight of centrally fuel-rich swirl coal combustion burners in the bottom row of the furnace during experiments. Various primary air ratios, flow characteristics, gas temperature and gas species concentrations in the burner region were measured. The results of these analyses show that with decreasing primary air ratio, the swirl intensity of air, divergence angles and maximum length and diameter of the central recirculation zone all increased, and the turbulence intensity of the jet flow peaked but decayed quickly. In the burner nozzle region, gas temperature, temperature gradient and CO concentration increased with decreasing primary air ratio, while O₂ and NO_x concentration decreased. Different primary air ratios, the gas temperatures and gas species concentrations in the side-wall region varied slightly.     

Effects of coal characteristics to performance of a highly efficient thermal power generation system based on pressurized oxy‐fuel combustion

Because of its fuel flexibility and high efficiency, pressurized oxy‐fuel combustion has recently emerged as a promising approach for efficient carbon capture and storage. One of the important options to design the pressurized oxy‐combustion is to determine method of coal (or other solid fuels) feeding: dry feeding or wet (coal slurry) feeding as well as grade of coals. The main aim of this research is to investigate effects of coal characteristics including wet or dry feeding on the performance of thermal power plant based on the pressurized oxy‐combustion with CO₂ capture versus atmospheric oxy‐combustion. A commercial process simulation tool (gCCS: the general carbon capture and storage) was used to simulate and analyze an advanced ultra‐supercritical(A‐USC) coal power plant under pressurized and atmospheric oxy‐fuel conditions. The design concept is based on using pure oxygen as an oxidant in a pressurized system to maximize the heat recovery through process integration and to reduce the efficiency penalty because of compression and purification units. The results indicate that the pressurized case efficiency at 30 bars was greater than the atmospheric oxy‐fuel combustion (base line case) by 6.02% when using lignite coal firing. Similarly, efficiency improvements in the case of subbituminous and bituminous coals were around 3% and 2.61%, respectively. The purity of CO₂ increased from 53.4% to 94% after compression and purification. In addition, the study observed the effects of coal‐water slurry using bituminous coal under atmospheric conditions, determining that the net plant efficiency decreased by 3.7% when the water content in the slurry increased from 11.12% to 54%. Copyright © 2016 John Wiley & Sons, Ltd.     

Experimental and numerical study of oxy‐methane flames in a porous‐plate reactor mimicking membrane reactor operation

The work investigates the reacting flow field, oxy‐methane flame characteristics and location, and the species distributions in a porous‐plate reactor mimicking the operation of oxygen transport membrane reactors (OTMRs). The study was performed experimentally and numerically considering ranges of operating equivalence ratio, from 0.5 to 1.0, and CO₂ concentrations in the total oxidizer flow (O₂ and CO₂), from 0% to 55% (by Vol). Oxygen was supplied through a slightly pressurized top and bottom chambers to cross the two porous plates to the central chamber, where a premixed mixture of CH₄ and CO₂ is introduced. ANSYS Fluent 17.1 software was used to solve for conservation and radiative transfer equations in the full three‐dimensional (3‐D) domain. The modified Westbrook‐Dryer (Oxy‐WD) two‐step reduced mechanism for oxy‐methane combustion was adapted for the calculations of chemical kinetics. The captured flame shapes using a high‐speed camera were compared with the calculated ones, and the results showed good agreements. At fixed equivalence ratio, elongated flames were obtained at higher CO₂ concentrations due to the increase in the mainstream Reynolds number and reduction in reaction rates, which delays the completeness of combustion. At fixed CO₂ concentration, the increase in equivalence ratio resulted in more compact and intense flames. The effective mixing and flame stability resulted in complete fuel conversion under stoichiometric condition. Stable flames were located between the two porous plates at reasonable distance. This perfect flame location prevents the thermal fracture of the membranes and improves their oxygen permeation flux, resulting in better combustion characteristics when the results are projected on the case of OTMRs. This implies efficient and safe applicability of the OTMRs by the condition that membranes can provide sufficient oxygen flux for complete combustion. A warm outer recirculation zone (ORZ) was created beside each porous plate, which helps anchoring the flame at the leading edge of the porous plate. The range of temperature within the ORZ was 800 to 1600 K, which lies in the operability limits of membranes for the case of OTMRs. The effective complete mixing and flame stability resulted in complete fuel conversion under stoichiometric condition. The temperature and species distributions within the reactor are presented in detail over wide ranges of operating conditions. The results recommended the reactor operation under stoichiometric combustion condition based on performance and economic points of views. The results are promising when projected on the application of the OTMRs under oxy‐combustion conditions for clean and efficient energy production.     

摆动式水平浓淡风煤粉燃烧器在670 t/h锅炉的应用研究

我厂2号锅炉(DG 670/13.7-8A)为四角切圆布置,一、二次风间隔布置,分上下两组,设计煤种为晋中贫煤.在实际运行中,煤质不稳定,锅炉着火和燃烧稳定性差.采用"摆动式水平浓淡风煤粉燃烧器"技术对燃烧器改造后,燃烧效率提高0.84%、在300 t/h时能稳定燃烧、炉膛无结渣,锅炉参数稳定.     

Role of CO2 in the CH4 oxidation and H2 formation during fuel-rich combustion in O2/CO2 environments

The effect of CO₂ reactivity on CH₄ oxidation and H₂ formation in fuel-rich O₂/CO₂ combustion where the concentrations of reactants were high was studied by a CH₄ flat flame experiment, detailed chemical analysis, and a pulverized coal combustion experiment. In the CH₄ flat flame experiment, the residual CH₄ and formed H₂ in fuel-rich O₂/CO₂ combustion were significantly lower than those formed in air combustion, whereas the amount of CO formed in fuel-rich O₂/CO₂ combustion was noticeably higher than that in air. In addition to this experiment, calculations were performed using CHEMKIN-PRO. They generally agreed with the experimental results and showed that CO₂ reactivity, mainly expressed by the reaction CO₂ + H → CO + OH (R1), caused the differences between air and O₂/CO₂ combustion under fuel-rich condition. R1 was able to advance without oxygen. And, OH radicals were more active than H radicals in the hydrocarbon oxidation in the specific temperature range. It was shown that the role of CO₂ was to advance CH₄ oxidation during fuel-rich O₂/CO₂ combustion. Under fuel-rich combustion, H₂ was mainly produced when the hydrocarbon reacted with H radicals. However, the hydrocarbon also reacted with the OH radicals, leading to H₂O production. In fact, these hydrocarbon reactions were competitive. With increasing H/OH ratio, H₂ formed more easily; however, CO₂ reactivity reduced the H/OH ratio by converting H to OH. Moreover, the OH radicals reacted with H₂, whereas the H radicals did not reduce H₂. It was shown that OH radicals formed by CO₂ reactivity were not suitable for H₂ formation. As for pulverized coal combustion, the tendencies of CH₄, CO, and H₂ formation in pulverized coal combustion were almost the same as those in the CH₄ flat flame.