Solid-state dye-sensitized solar cells based on ZnO nanoparticle and nanorod array hybrid photoanodes

The effect of ZnO photoanode morphology on the performance of solid-state dye-sensitized solar cells (DSSCs) is reported. Four different structures of dye-loaded ZnO layers have been fabricated in conjunction with poly(3-hexylthiophene). A significant improvement in device efficiency with ZnO nanorod arrays as photoanodes has been achieved by filling the interstitial voids of the nanorod arrays with ZnO nanoparticles. The overall power conversion efficiency increases from 0.13% for a nanorod-only device to 0.34% for a device with combined nanoparticles and nanorod arrays. The higher device efficiency in solid-state DSSCs with hybrid nanorod/nanoparticle photoanodes is originated from both large surface area provided by nanoparticles for dye adsorption and efficient charge transport provided by the nanorod arrays to reduce the recombinations of photogenerated carriers.     

Fabrication and characterization of silicon wire solar cells having ZnO nanorod antireflection coating on Al-doped ZnO seed layer

In this study, we have fabricated and characterized the silicon [Si] wire solar cells with conformal ZnO nanorod antireflection coating [ARC] grown on a Al-doped ZnO [AZO] seed layer. Vertically aligned Si wire arrays were fabricated by electrochemical etching and, the p-n junction was prepared by spin-on dopant diffusion method. Hydrothermal growth of the ZnO nanorods was followed by AZO film deposition on high aspect ratio Si microwire arrays by atomic layer deposition [ALD]. The introduction of an ALD-deposited AZO film on Si wire arrays not only helps to create the ZnO nanorod arrays, but also has a strong impact on the reduction of surface recombination. The reflectance spectra show that ZnO nanorods were used as an efficient ARC to enhance light absorption by multiple scattering. Also, from the current-voltage results, we found that the combination of the AZO film and ZnO nanorods on Si wire solar cells leads to an increased power conversion efficiency by more than 27% compared to the cells without it.     

Facile solution growth of vertically aligned ZnO nanorods sensitized with aqueous CdS and CdSe quantum dots for photovoltaic applications

Vertically aligned single crystalline ZnO nanorod arrays, approximately 3 μm in length and 50-450 nm in diameter are grown by a simple solution approach on a Zn foil substrate. CdS and CdSe colloidal quantum dots are assembled onto ZnO nanorods array using water-soluble nanocrystals capped as-synthesized with a short-chain bifuncional linker thioglycolic acid. The solar cells co-sensitized with both CdS and CdSe quantum dots demonstrate superior efficiency compared with the cells using only one type of quantum dots. A thin Al2O3 layer deposited prior to quantum dot anchoring successfully acts as a barrier inhibiting electron recombination at the Zn/ZnO/electrolyte interface, resulting in power conversion efficiency of approximately 1% with an improved fill factor of 0.55. The in situ growth of ZnO nanorod arrays in a solution containing CdSe quantum dots provides better contact between two materials resulting in enhanced open circuit voltage.     

Novel ZnO microflowers on nanorod arrays: local dissolution-driven growth and enhanced light harvesting in dye-sensitized solar cells

ZnO nanostructures were manipulated, via a low-temperature solution process, from pure nanorod arrays to complex nanostructures of microflowers on nanorod arrays with adjusted quantities of flowers. We proposed the mechanism of local dissolution-driven growth to rationally discuss the novel growth process. These nanostructures were used as photoanodes in dye-sensitized solar cells. Compared to pure nanorod arrays, the nanorod array-microflower hierarchical structures improved the power conversion efficiency from 0.41% to 0.92%, corresponding to a 124% efficiency increase. The enhancement of the efficiency was mainly ascribed to the synergistic effect of the enhanced surface area for higher dye loading and the improved light harvesting from efficient light scattering. Present results provide a promising route to improve the capability of light-harvesting for ZnO nanorod array-based DSSCs.     

Improved dye-sensitized solar cell with a ZnO nanotree photoanode by hydrothermal method

This study investigated the influence of ZnO nanostructures on dye adsorption to increase the photovoltaic conversion efficiency of solar cells. ZnO nanostructures were grown in both tree-like and nanorod (NR) arrays on an AZO/FTO film structure by using a hydrothermal method. The results were observed in detail using X-ray diffraction, field-emission scanning electron microscopy (FE-SEM), UV-visible spectrophotometry, electrochemical impedance spectroscopy, and solar simulation. The selective growth of tree-like ZnO was found to exhibit higher dye adsorption loading and conversion efficiency than ZnO NRs. The multiple ‘branches’ of ‘tree-like nanostructures’ increases the surface area for higher light harvesting and dye loading while reducing charge recombination. These improvements result in a 15% enhancement in power conversion. The objective of this study is to facilitate the development of a ZnO-based dye-sensitized solar cell.     

Growth of three-dimensional ZnO nanorods by electrochemical method for quantum dots-sensitized solar cells

There-dimensional (3D) superstructure was expected to fabricate high performance photoelectrodes of quantum dot-sensitized solar cells (QDSCs). In this paper, the ZnO 3D superstructure with multi-layer structure (3D ZnO nanorods) was grown on ITO glass by a novel electrochemical method at low temperature (60–90 °C). The 3D ZnO nanorods were composed of close-packed ZnO nanorod bundles with wide dimension distribution ranging from hundreds of nanometers to several micrometers. The effects of some important parameters, such as concentration of Zn(NO₃)₂, deposition temperature and concentration of ZnO nanoparticles (served as growth seeds for ZnO nanorods), on the morphology of 3D ZnO nanorods were also studied by scanning electron microscopy. Once being applied in QDSCs, the 3D ZnO nanorods showed more superior photoelectrochemical performance to ZnO nanorod array. The conversion efficiency of 1.42% achieved by the QDSC based on 3D ZnO nanorods was a very promising value for the QDSCs based on ZnO electrodes.     

Effect of CdSe quantum dots on the performance of hybrid solar cells based on ZnO nanorod arrays

This paper reports the fabrication and interface modification of hybrid inverted solar cells based on ZnO nanorod arrays and poly (3-hexylthiophene). CdSe quantum dots (QDs) are grafted to the ZnO nanorod array successfully by bifunctional molecule mercaptopropionic acid to enhance the device performance. The power conversion efficiency of the device is increased by 109% from 0.11% to 0.23% under simulated 1 sun AM 1.5 solar illumination at 100 mW/cm² after the modification. The grafting of CdSe QDs effectively enhanced the excition generation and dissociation on the organic/inorganic interface. This work may provide a general method for increasing the efficiency of organic–inorganic hybrid solar cells by interface modification.     

The Effects of Co-Sensitization and Electronic Structure of Nanocrystalline N/TiO<Subscript>2</Subscript> Anode on the Performance of Dye-Sensitized Solar Cells

N/TiO₂ nanocrystalline film anodes were obtained by doping nonmetallic element N which could change the LUMO of anode. This paper also studied the match between the LUMO energy lever of N/TiO₂ anode and the dye, which led to the easy injection of electron from the excited state of dye molecule to the conduction band of semiconductor, and thus improved the photoelectric conversion efficiency and reduced the impedance of solar cells. The solar cell based on N/TiO₂ anode film co-sensitized by P3HT (poly(3-hexylthiophene))/N719(RuL2(NCS)2:2TBA (L = 2,2′-bipyridyl-4,4′-dicarboxylic acid)), the absorption region of which covered the entire visible region in solar cells, showed a short-circuit current density of 6.88 mA cm⁻², an open-circuit voltage of 0.616 V, and a photoelectric conversion efficiency of 2.34%.     

Growth of vertically aligned ZnO nanorods using textured ZnO films

A hydrothermal method to grow vertical-aligned ZnO nanorod arrays on ZnO films obtained by atomic layer deposition (ALD) is presented. The growth of ZnO nanorods is studied as function of the crystallographic orientation of the ZnO films deposited on silicon (100) substrates. Different thicknesses of ZnO films around 40 to 180 nm were obtained and characterized before carrying out the growth process by hydrothermal methods. A textured ZnO layer with preferential direction in the normal c-axes is formed on substrates by the decomposition of diethylzinc to provide nucleation sites for vertical nanorod growth. Crystallographic orientation of the ZnO nanorods and ZnO-ALD films was determined by X-ray diffraction analysis. Composition, morphologies, length, size, and diameter of the nanorods were studied using a scanning electron microscope and energy dispersed x-ray spectroscopy analyses. In this work, it is demonstrated that crystallinity of the ZnO-ALD films plays an important role in the vertical-aligned ZnO nanorod growth. The nanorod arrays synthesized in solution had a diameter, length, density, and orientation desirable for a potential application as photosensitive materials in the manufacture of semiconductor-polymer solar cells.

PACS

61.46.Hk, Nanocrystals; 61.46.Km, Structure of nanowires and nanorods; 81.07.Gf, Nanowires; 81.15.Gh, Chemical vapor deposition (including plasma-enhanced CVD, MOCVD, ALD, etc.)     

Hybrid polymer/ZnO solar cells sensitized by PbS quantum dots

Poly[2-methoxy-5-(2-ethylhexyloxy-p-phenylenevinylene)]/ZnO nanorod hybrid solar cells consisting of PbS quantum dots [QDs] prepared by a chemical bath deposition method were fabricated. An optimum coating of the QDs on the ZnO nanorods could strongly improve the performance of the solar cells. A maximum power conversion efficiency of 0.42% was achieved for the PbS QDs' sensitive solar cell coated by 4 cycles, which was increased almost five times compared with the solar cell without using PbS QDs. The improved efficiency is attributed to the cascade structure formed by the PbS QD coating, which results in enhanced open-circuit voltage and exciton dissociation efficiency.     

All-solid-state quantum-dot-sensitized solar cells with compact PbS quantum-dot thin films and TiO2 nanorod arrays

To improve the electron injection efficiency from PbS quantum dots to TiO₂ nanorods and prevent the direct contact of spiro-OMeTAD and TiO₂ nanorods, a compact PbS quantum-dot thin film can be successfully obtained on TiO₂ nanorod arrays 360 nm in length by repeated spin coating of Pb(Ac)₂, Na₂S and 1,2-ethanedithiol solution in a step-by-step process. The corresponding solid-state quantum-dot-sensitized solar cells are fabricated using a novel structured FTO/compact PbS quantum-dot thin film sensitized TiO₂ nanorod array/spiro-OMeTAD/Au that achieves a photoelectric conversion efficiency of 3.57% under AM 1.5 G illumination (100 mW cm⁻²), which represents a high value among all-solid-state PbS quantum-dot-sensitized TiO₂ nanorod array solar cells.     

Preparation and photoelectrochemical properties of CdS quantum dot-sensitized ZnO nanotube arrays

CdS/ZnO nanotubes (NTs) arrays were synthesized on a transparent conductive glass (FTO) substrate by hydrothermal method, chemical bath etching and successive ionic layer adsorption and reaction (SILAR) method, which were used in semiconductor-sensitized photoelectrochemical cells (PECs). The crystal structure, morphology and photoelectrochemical conversion properties of different photoanodes were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscope (TEM), high resolution transmission electron microscope (HRTEM), and electrochemical workstation. The results show a heterojunction has been formed between ZnO and CdS QDs. The ZnO NTs and CdS QDs played a remarkable controllability for PEC performances. The photoelectrochemical conversion efficiency of ZnO NTs photoanodes was 3 times that of ZnO nanorods (NRs) arrays photoanodes. After sensitization of CdS quantum dots, the photoelectrochemical conversion efficiency of CdS/ZnO NRs was improved by 7 times and the CdS/ZnO NTs was increased by 4 times. These results demonstrate that the CdS/ZnO core-shell structure can provide a facile and compatible frame for the potential applications in nanotube-based solar cells.     

ZnO纳米棒水热法生长与表征

采用两步法在FTO导电玻璃衬底上制备ZnO纳米棒,首先利用浸渍-提拉法在FTO导电玻璃衬底上制备ZnO晶种层,然后把有ZnO晶种层的FTO衬底放入盛有生长溶液的反应釜中利用水热法制备ZnO纳米棒.研究了生长溶液的浓度、生长温度和生长时间对所制备的对ZnO纳米棒阵列的微结构和光致发光性能的影响,利用X射线衍射(XRD)、扫描电子显微镜(SEM)和光致发光谱(PL)研究了ZnO样品的结构、形貌和光学性质.实验结果表明:所制备的ZnO纳米棒呈现六方纤锌矿结构,沿(002)晶面择优取向生长,纳米棒的平均直径约为100 nm,长度约为2.5 μm.所制备的ZnO纳米棒在390 nm附近具有很强的紫外发光峰和在550 nm附近有较弱的宽绿光发光峰.     

Room-temperature nonequilibrium growth of controllable ZnO nanorod arrays

In this study, controllable ZnO nanorod arrays were successfully synthesized on Si substrate at room temperature (approx. 25°C). The formation of controllable ZnO nanorod arrays has been investigated using growth media with different concentrations and molar ratios of Zn(NO₃)₂ to NaOH. Under such a nonequilibrium growth condition, the density and dimension of ZnO nanorod arrays were successfully adjusted through controlling the supersaturation degree, i.e., volume of growth medium. It was found that the wettability and electrowetting behaviors of ZnO nanorod arrays could be tuned through variations of nanorods density and length. Moreover, its field emission property was also optimized by changing the nanorods density and dimension.     

Effect of ZnO seed layers on the solution chemical growth of ZnO nanorod arrays

High density ZnO nanorod arrays were grown on Si substrates coated with ZnO seed layers via aqueous solution route. The ZnO seed layers were deposited on the substrate using DC reactive sputtering and RF magnetron sputtering. It was found that ZnO seed layer with (1 0 3) preferred orientation, prepared using DC reactive sputtering, did not facilitate the formation of ZnO nanorods in the solution grown process. Prior seeding of the surface by ZnO layer with (0 0 2) preferred orientation, deposited using RF magnetron sputtering, leads to nucleation sites on which ZnO nanorod arrays can grow in a highly aligned fashion. ZnO nanorods with well-defined hexagonal facets (0 0 2) were grown almost vertically over the entire substrate. The uniformity and alignment of the nanorod arrays are strongly related to the properties of underneath ZnO seed layers.     

Hydrogen treatment-improved uniform deposition of Ag nanoparticles on ZnO nanorod arrays and their visible-light photocatalytic and surface-enhanced Raman scattering properties

ZnO nanorod arrays were synthesized by chemical bath deposition. After heat treatment in hydrogen or air, Ag nanoparticles were deposited on ZnO nanorod arrays by photo-reduction method. The size of Ag nanoparticles as well as the surface morphology, structure, composition, and optical property of ZnO nanorod arrays before and after the deposition of Ag nanoparticles were characterized by SEM, XRD, EDS, and UV/VIS/NIR spectrophotometer. As compared to the samples with heat treatment in air or without heat treatment, the ZnO nanorod arrays after heat treatment in hydrogen allowed Ag nanoparticles to be deposited more uniformly, densely, and numerously. Also, they exhibited higher efficiency for the visible light-driven photocatalytic degradation of Rhodamine 6G (R6G) dye. The effects of the amount of Ag nanoparticles, initial dye concentration, and temperature on the photocatalytic degradation efficiency were investigated. Furthermore, they also exhibited better surface-enhanced Raman scattering property for the detection of R6G dyes.     

CdSe nanocrystal sensitized ZnO core-shell nanorod array films: Preparation and photovoltaic properties

ZnO/CdSe core-shell nanorod array films were synthesized via a two-step method. ZnO nanorod array films were first grown on a TCO substrate, and then CdSe nanocrystals were deposited on the nanorods to form core-shell structured films. The resulting films were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV-vis absorption spectroscopy. Especially, dark-field images and transmission electron diffraction of the TEM were used to study the morphology and the chemical nanostructure of the ZnO/CdSe core-shell nanorods in detail. We investigated the photovoltaic performance of the resulting ZnO/CdSe core-shell nanorod array films as solar cell photoanodes. Parameters, such as the length of the ZnO nanorods, the shell phase structure and the deposition time of the CdSe nanocrystals were found to affect the photovoltaic performance of the solar cell. This study provides a facile method to prepare nanocomposite photoanodes of solar cells, and gives some insight about the fundamental mechanisms that improve the performance.     

Electrochemical deposition of branched hierarchical ZnO nanowire arrays and its photoelectrochemical properties

Branched hierarchical ZnO nanowire arrays are synthesized on fluorine-doped tin oxide (FTO) substrate via a two-step electrochemical deposition process, which involves the electrodeposition of ZnO nanowire arrays on conductive glass substrate, followed by the electrochemical growth of ZnO nanorod branches on the backbones of the primary ZnO nanowires. The formation mechanism of the branched hierarchical nanostructure is discussed. It is demonstrated that coating the primary nanowire arrays with ZnO nanoparticles seed layer plays a key role in synthesising the branched hierarchical ZnO nanostructure. By adjusting the concentration of Zn(CH₃COO)₂ colloid in coating process and the reaction time of the second-step deposition, the density and the length of the secondary nanorod branches in the hierarchical nanostructures can be both varied. Moreover, the photoelectrochemical properties of the dye-sensitized solar cell (DSSC) based on branched hierarchical ZnO nanowire arrays are investigated. Due to the enlargement of the internal surface area within the branched nanostructure photoelectrode, the DSSC consisting of branched hierarchical ZnO nanowire arrays yields a power conversion efficiency of 0.88%, which is almost twice higher than that of the DSSC fabricated using bare ZnO nanowire arrays.     

氧化锌纳米棒光催化降解染料废水的研究

采用水热合成法制备了ZnO纳米棒阵列。利用SEM和XRD对ZnO纳米棒的形貌和物相结构进行了表征。研究了光照时间、pH、ZnO投加量等因素对染料废水吸光度去除率的影响。实验结果表明,在紫外光照2 h、pH为10、ZnO纳米棒投加量为0.02 g的优化反应条件下,亚甲基蓝废水、分散橙GFL废水和直接耐酸大红4BS废水的吸光度去除率分别为19.32%、9.28%和13.50%。     

Selective Growth of Vertical-aligned ZnO Nanorod Arrays on Si Substrate by Catalyst-free Thermal Evaporation

By thermal evaporation of pure ZnO powders, high-density vertical-aligned ZnO nanorod arrays with diameter ranged in 80–250 nm were successfully synthesized on Si substrates covered with ZnO seed layers. It was revealed that the morphology, orientation, crystal, and optical quality of the ZnO nanorod arrays highly depend on the crystal quality of ZnO seed layers, which was confirmed by the characterizations of field-emission scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and photoluminescence measurements. For ZnO seed layer with wurtzite structure, the ZnO nanorods grew exactly normal to the substrate with perfect wurtzite structure, strong near-band-edge emission, and neglectable deep-level emission. The nanorods synthesized on the polycrystalline ZnO seed layer presented random orientation, wide diameter, and weak deep-level emission. This article provides a C-free and Au-free method for large-scale synthesis of vertical-aligned ZnO nanorod arrays by controlling the crystal quality of the seed layer.