常压等离子体改善合成纤维吸湿性的研究

用氦气作为等离子体的气体源、对涤纶、锦纶6、高强度聚乙烯纤维,Twaron 1000芳纶4种合成纤维进行常压等离子体处理,改善纤维的吸湿性能。结果表明:常压等离子体处理,对涤纶和锦纶6的表面有一定的刻蚀作用,但对高强度聚乙烯纤维、Twaron 1000芳纶的表面没有明显影响;经常压等离子体处理后,合成纤维表面氧、氮有所增加,吸湿性能得到提高,强度没有显著变化。     

水分对常压等离子体处理纤维结构与性能的影响

在空气相对湿度为5%,65%和95%的条件下,应用氦气/氧气常压等离子体处理芳纶和超高强度聚乙烯纤维,采用单纤维抽拔实验测定处理前后纤维与环氧树脂间的层间剪切强度,利用原子力显微镜和X射线光电子能谱仪分析等离子体处理前后纤维表面形态和化学成分的变化.结果表明:等离子体处理纤维随着处理环境湿度的增加,水分促进了芳纶表面的...     

等离子体处理对芳纶性能的影响

芳纶作为增强材料在复合材料中有广泛的应用,其界面性能是影响其复合材料界面粘结性能的重要因素。分别采用H2、空气低温等离子体对芳纶表面进行了处理。研究了等离子体表面改性后芳纶性能的变化。结果表明:经低温等离子体处理后纤维表面张力增大,由46.0mN·m-1增加到63.2mN·m-1;表面极性增强,极性分数由58.0%提高到69.9%,而纤维单丝断裂强度未有明显变化。     

氨气等离子体改性处理芳纶Ⅲ表面的研究

以氨气为反应气体,对芳纶Ⅲ进行等离子体表面改性处理,研究了等离子体处理时间和处理功率对纤维表面性能的影响;采用X射线光电子能谱、场发射扫描电镜、接触角和微脱粘实验等测试方法对改性前后纤维表面元素组成、形貌、润湿能力以及界面粘结强度进行表征。结果表明:芳纶Ⅲ经过氨气等离子体改性后,表面含氮极性基团的含量增加,粗糙程度增大,润湿能力得到明显的改善;当氨气等离子体处理时间为15 min,功率为100 W时,芳纶Ⅲ与环氧树脂的界面粘结强度从处理前的12.9 MPa提高到18.2 MPa,与水的接触角由处理前的71.4°下降到46.8°。     

低温等离子体处理对芳纶/环氧界面性能的影响

在采用低温等离子体对芳纶纤维进行表面处理后，用扫描电镜观察处理前后的纤维表面，测试了纤维的拉伸性能，并用单纤维抽拔法对芳纶纤维／环氧树脂的界面性能做了定量的表征。实验结果表明：经低温等离子体处理后，芳纶纤维表面变得粗糙，拉伸强度随处理时间延长而下降，纤维初始模量和断裂伸长率略有下降，而芳纶／环氧界面的粘结强度有所提高。     

空气等离子体处理芳纶Ⅲ的性能研究

比较了国产芳纶Ⅲ与芳纶1414以及进口Twaron纤维的表面性能;采用空气等离子体处理技术对芳纶Ⅲ的表面进行改性,研究了空气等离子体处理工艺条件以及处理前后芳纶Ⅲ的结构与性能的变化。结果表明:国产芳纶Ⅲ的表面存在不均匀的浅沟槽,比芳纶1414和Twaron纤维表面粗糙,其表面浸润性较差,但却优于芳纶1414和Twaron纤维;空气等离子体处理芳纶Ⅲ的最佳条件为放电功率65 W,空气放电气压2 000 Pa,处理时间11 min,在此条件下处理的芳纶Ⅲ表面接触角由未处理时的55.8°降至41.5°,纤维的浸润性能得到改善,而其力学性能和大分子结构不受影响。     

介质阻挡放电等离子体处理芳纶的表面性能研究

采用介质阻挡放电(DBD)装置对芳纶1414表面进行改性处理,探讨低温等离子体处理对纤维表面性能的影响。结果表明:经过DBD等离子体处理后,芳纶1414纤维表面粗糙程度加剧,粘结性能和浸润性能有了明显的改善;当DBD等离子体处理功率为200～300 W,时间为60 s,氩气流量为2～3 L/min时,芳纶1414的界面剪切强度从处理前的11.9 MPa上升到14.2 MPa,接触角由处理前的85.0°下降到了60.6°。     

常压等离子射流表面改性超高模量聚乙烯纤维

利用常压等离子射流(APPJ)方法对超高模量聚乙烯(UHMPE)纤维进行表面改性处理。研究了处理前后UHMPE纤维的力学性能、表面形貌、化学成分、表面粘结性能的变化。结果表明,常压等离子射流处理后,UHMPE纤维的强度未发生显著变化,纤维表面粗糙度增加,表面氧元素的含量增加,表面极性基团增加,纤维与环氧树脂之间的粘结性能得到显著的改善。     

低温等离子体技术在超高相对分子质量聚乙烯纤维表面改性中的应用

介绍了低温等离子体的概念、分类及其在超高相对分子质量聚乙烯纤维(UHMWP E)表面改性方面的特点;阐述了国内外在低温等离子体对UHMWPE纤维表面改性前后纤维本身及其复合材料性能的影响情况;简介了用自行研制的低温等离子体设备对UHMWPE纤维进行表面改性的研究结果和低温等离子体处理UHMWPE纤维表面改性的发展前景。实验表明,UHMWPE纤维经过等离子体处理后表面产生刻蚀和交联,其与树脂间的粘结性能改善;该低温等离子体设备能满足UHMWPE纤维表面改性连续化生产需要。     

芳纶纤维等离子体接枝改性处理研究

采用等离子体接枝对芳纶纤维表面进行改性处理,采用XPS、浸润性、界面剪切强度对等离子体接枝处理前后的表面组成、复合材料界面粘接性能等进行了研究,结果表明:等离子体接枝处理可以有效地提高芳纶纤维表面的极性官能团,增加与基体树脂-环氧树脂的浸润性,进而提高芳纶/环氧复合材料的界面粘接强度.     

The effect of atmospheric‐pressure air plasma discharge power on adhesive properties of aramid fibers

After exposure to the atmospheric‐pressure air plasma at different discharge powers, the adhesion characteristics of Twaron aramid fibers were investigated. For the 12 s‐300 W plasma treatment, the interlaminar shear strength of Twaron fiber reinforced thermoplastic poly(phthalazinone ether sulfone ketone) was increased from 46.0 to 61.7 MPa by 34.1%, and the diffusion of water molecule into the resulting composites was proved to be effectively prevented. These results showed that surface adhesive properties of the plasma‐treated aramid fibers were improved. At the power level of 300 W, X‐ray photoelectron spectroscopy analysis revealed the increases in concentrations of oxygen and nitrogen polar groups on the fiber surface, and atomic force microscopy observations led to the conclusion that the fiber surface morphology was changed and the surface roughness was greatly increased. These new polar and irregular surface structures accounted for the better adhesion between the fiber and the matrix, while due to the reasonability of this discharge power level applied to the surface modification, the measured fiber tensile strength only decreased by 2.0%. POLYM. COMPOS., 37:620–626, 2016. © 2014 Society of Plastics Engineers     

Influence of moisture regain of aramid fibers on effects of atmospheric pressure plasma treatment on improving adhesion with epoxy

One difference between a low‐pressure plasma treatment and an atmospheric pressure plasma treatment is that in the atmosphere, the substrate material may contain significant quantities of moisture, which could potentially influence the effects of the plasma treatment. To investigate how the existence of moisture affects atmospheric pressure plasma treatment, aramid fibers (Twaron 1000) with three different moisture regains (0.5, 4.5, and 5.5%) were treated by an atmospheric pressure plasma jet for 3 s at a gas flow rate of 8 L/min, a treatment head temperature of 100°C, and a power of 10 W. The scanning electron microscopy analysis showed no observable surface morphology change for the plasma treated samples. X‐ray photoelectron spectroscopy analysis showed the oxygen contents of the 0.5 and 4.5% moisture regain groups increased from that of the control, although the opposite was true for the 5.5% moisture regain group. The advancing contact angles of the treated fibers decreased about 8°–16° whereas their receding contact angles decreased about 17°–27°. The interfacial shear strengths of the treated fibers as measured using microbond pull‐out tests were more than doubled when the moisture regain was 4.5 or 5.5%, whereas it increased by 58% when the moisture regain was 0.5%. In addition, no significant difference in single fiber tensile strength was observed among the plasma treated samples and the control sample. Therefore, we concluded that moisture regain promoted the plasma treatment effect in the improvement of the adhesion property of aramid fibers to epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 242–247, 2006     

Direct fluorination of Twaron fiber and investigation of mechanical thermal and morphological properties of high density polyethylene and Twaron fiber composites

Composites consisting of high density polyethylene (HDPE) reinforced with randomly oriented chopped Twaron fibers (both fluorinated and nonfluorinated) show a significant increase in mechanical and thermal properties. To increase the better fiber matrix adhesion, the Twaron fiber is surface fluorinated using elemental fluorine. The surface of the Twaron fiber becomes very rough and the diameter of Twaron fiber increases from ～ 12 to 14 μm after fluorination. The composites were prepared using solution method to overcome the damage of the fiber. The tensile strength and the Young's modulus increases with increasing fiber content. The tensile strength and modulus of modified fiber (fluorinated Twaron fiber) composites is much higher than nonmodified fiber composites indicating that there is better mechanical interlocking between the modified fiber and the matrix. Thermal properties obtained from DSC and DTA‐TG analysis of the fluorinated fiber composites are also improved. Contact angle measurements, as well as the surface energy measurements, indicate that the composites are more wettable and is maximum for fluorinated fiber composites i.e., surface energy for fluorinated fiber composites is highest. Crystallinity is also higher for fluorinated fiber composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

等离子体射流载气流量大小对玻璃纤维改性效果影响的研究

通过大气压等离子体射流在玻璃纤维（GF）表面沉积氧化硅（SiOx）纳米颗粒的方法改善玻璃纤维增强聚丙烯（GFRP）复合材料的界面结合性能,利用扫描电子显微镜、原子力显微镜和X射线光电子能谱等表征分析了改性纤维的表面形貌、化学成分、润湿性能和复合材料的界面结合性能,并考察了等离子体射流载气流量大小对GF改性效果的影响。结果表明,当载气流量为40 mL/min时,GF的改性效果最好,且此时GF的表面能相比对照组提高了43.18%,GFRP复合材料的层间剪切强度提高了30.79%;经过等离子体处理后,GF的表面粗糙度增大,极性官能团增多,复合材料的界面结合性能提升。     

高性能纤维的弯曲疲劳断裂研究

在自制弯曲疲劳装置上 ,对 3种高强对位芳纶及超高相对分子质量聚乙烯纤维 (Dyneema SK65 )进行双面弯曲疲劳试验。结果表明 ,Twaron 2 0 0 0弯曲疲劳寿命的自然对数与预加应力、弯曲角度呈线性关系 ,Dyneema SK65弯曲疲劳寿命明显长于对位芳纶 ,Twaron 2 0 0 0 ,Kevlar 12 9相近 ,都比Kevlar 2 9略长 ;高强型对位芳纶的弯曲疲劳断裂断口芯层呈现出“毛笔头”或“拔丝形”原纤化分裂形态 ,超高相对分子质量聚乙烯纤维弯曲疲劳断裂断口有明显的脆性折断形态 ,无原纤出现。     

低温等离子体处理UHMWPE纤维表面性能的多指标优化

利用正交表安排试验,对超高相对分子质量聚乙烯(UHMWPE)纤维进行空气低温等离子体处理,测试各处理条件下UHMWPE纤维的力学和表面摩擦性能;采用矩阵分析法对多指标正交试验结果进行优化分析,找出最优方案并进行黏着性试验验证。结果表明:经空气低温等离子体处理后,UHMWPE纤维的断裂强度有所减小,表面静、动摩擦因数有较大幅度的提高;处理纤维的最优方案为功率50 W、压强15 Pa、时间150 s,此时纤维的断裂强度损失率仅为2.53%,剥离功为未处理时的4.25倍,说明由矩阵分析法得出的最优方案在保证纤维断裂强度损失很小的情况下,黏着性得到了很大程度的改善。     

Surface modification of ultra high modulus polyethylene fibers by an atmospheric pressure plasma jet

To improve their adhesion properties, ultra high modulus polyethylene (UHMPE) fibers were treated by an atmospheric pressure helium plasma jet (APPJ), which was operated at radio frequency (13.56 MHz). The surface properties of the fibers were investigated by X‐ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and contact angle measurement. The surface dyeability improvement after plasma treatments was investigated using laser scanning confocal microscopy (LSCM). The adhesion strengths of the fibers with epoxy were evaluated by microbond tests. In addition, the influence of operational parameters of the plasma treatment including power input and treatment temperature was studied. XPS analysis showed a significant increase in the surface oxygen content. LSCM results showed that the plasma treatments greatly increased fluorescence dye concentrations on the surface and higher diffusion rate to the fiber center. The tensile strength of UHMPE fiber either remained unchanged or decreased by 10–13.6% after plasma treatment. The contact angle exhibited a characteristic increase in wettability, due to the polar groups introduced by plasma treatment. The microbond test showed that the interfacial shear strengths (IFSS) increase significantly (57–139%) after plasma treatment for all groups and the optimum activation is obtained at 100°C and 5 W power input. SEM analysis showed roughened surfaces after the plasma treatments. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008