Effect of heat input on microstructure and mechanical properties of dissimilar joints of AISI 316L steel and API X70 high-strength low-alloy steel

The microstructure and mechanical properties of dissimilar joints of AISI 316L austenitic stainless steel and API X70 high-strength low-alloy steel were investigated.For this purpose,gas tungsten arc welding(GTAW)was used in three different heat inputs,including 0.73,0.84,and 0.97 kJ/mm.The microstructural investigations of different zones including base metals,weld metal,heat-affected zones and interfaces were performed by optical microscopy and scanning electron microscopy.The mechanical properties were measured by microhardness,tensile and impact tests.It was found that with increasing heat input,the dendrite size and inter-dendritic spacing in the weld metal increased.Also,the amount of delta ferrite in the weld metal was reduced.Therefore,tensile strength and hardness were reduced and impact test energy was increased.The investigation of the interface between AISI 316L base metal and ER316L filler metal showed that increasing the heat input increases the size of austenite grains in the fusion boundary.A transition region was formed at the interface between API X70 steel and filler metals.     

Effect of Activated Flux on the Microstructure, Mechanical Properties, and Residual Stresses of Modified 9Cr-1Mo Steel Weld Joints

A novel variant of tungsten inert gas (TIG) welding called activated-TIG (A-TIG) welding, which uses a thin layer of activated flux coating applied on the joint area prior to welding, is known to enhance the depth of penetration during autogenous TIG welding and overcomes the limitation associated with TIG welding of modified 9Cr-1Mo steels. Therefore, it is necessary to develop a specific activated flux for enhancing the depth of penetration during autogeneous TIG welding of modified 9Cr-1Mo steel. In the current work, activated flux composition is optimized to achieve 6 mm depth of penetration in single-pass TIG welding at minimum heat input possible. Then square butt weld joints are made for 6-mm-thick and 10-mm-thick plates using the optimized flux. The effect of flux on the microstructure, mechanical properties, and residual stresses of the A-TIG weld joint is studied by comparing it with that of the weld joints made by conventional multipass TIG welding process using matching filler wire. Welded microstructure in the A-TIG weld joint is coarser because of the higher peak temperature in A-TIG welding process compared with that of multipass TIG weld joint made by a conventional TIG welding process. Transverse strength properties of the modified 9Cr-1Mo steel weld produced by A-TIG welding exceeded the minimum specified strength values of the base materials. The average toughness values of A-TIG weld joints are lower compared with that of the base metal and multipass weld joints due to the presence of δ-ferrite and inclusions in the weld metal caused by the flux. Compressive residual stresses are observed in the fusion zone of A-TIG weld joint, whereas tensile residual stresses are observed in the multipass TIG weld joint.     

Argon-Hydrogen Shielding Gas Mixtures for Activating Flux-Assisted Gas Tungsten Arc Welding

Using activating flux for gas tungsten arc welding (GTAW) to improve penetration capability is a well-established technique. Argon is an inert gas and the one most widely used as a shielding gas for GTAW. For the most austenitic stainless steels, pure argon does not provide adequate weld penetration. Argon–hydrogen mixtures give a more even heat input to the workpiece, increasing the arc voltage, which tends to increase the volume of molten material in the weld pool as well as the weld depth-to-width ratio. Great interest has been shown in the interaction between activating flux and the hydrogen concentration in an argon-based shielding gas. In this study, the weld morphology, the arc profile, the retained delta ferrite content, the angular distortion, and the microstructures were examined. The application of an activating flux combining argon and hydrogen for GTAW is important in the industry. The results of this study are presented here.     

Microstructural and Mechanical Characterization of as Weld and Aged Conditions of AA2219 Aluminium Alloy by Gas Tungsten Arc Welding Process

In this article, Welding of AA2219 aluminium alloy using Gas tungsten arc welding process (GTAW) and evaluation of metallurgical, mechanical and corrosion properties of the joints are discussed. The weld samples were subjected to ageing process at the temperature range of 195°C for a period of 5 h to improve the properties. AA2219 aluminium plates of thickness of 25 mm were welded using gas tungsten arc welding (GTAW) process in double V butt joint configuration. The input parameters considered in this work are welding current, voltage and welding speed. Tensile strength and hardness were measured as performance characteristics. The variation in the properties were justified with the help of microstructures. The same procedures were repeated for post weld heat treated samples and a comparison was made between as weld condition and age treated conditions. The post weld heat samples had better tensile strength and hardness values on comparing with the as weld samples. Fracture surface obtained from the tensile tested specimen revealed ductile mode of failure.     

Investigations on Dissimilar Weld of UNS S32205 DSS and ASTM A517 Steel

In the present research, microstructure and mechanical properties of 2205 duplex stainless steel/A517 quench and tempered low alloy steel dissimilar joint were investigated. For this purpose, gas tungsten arc welding was used with ER2209 filler metal. Characterizations were conducted by optical microscopy, scanning electron microscopy equipped with an energy dispersive spectroscopy and X-ray diffraction. Mechanical properties were evaluated in micro-hardness, tensile and impact tests. Microstructure in the weld zone included an austenitic continuous network in the matrix of primary ferrite. No brittle phases were formed in the weld metal and stainless steel heat affected zone (HAZ). The weld metal/A517 interface showed higher hardness than other regions. Tensile tests indicated that the values of the yield and tensile strength were 663 and 796 MPa, respectively. Impact tests indicated that the weld zone had almost the same impact energy as base metals. The minimum impact energy of 12 J was related to A517 HAZ. The results of scanning electron microscopy for fracture surfaces indicated that weld zone, 2205 HAZ and A517 HAZ had ductile, ductile–brittle and brittle fracture mode, respectively.     

Investigations on metallurgical and mechanical properties of CO2 laser beam welded Alloy 825

In the research work, an attempt is made to join nickel-based alloy 825 by employing CO₂ laser beam welding. Successful full penetration weld joint of a 5?mm thick plate is achieved with a very low heat input of 120?J-mm^?1. Narrow weld bead width of 0.6?mm at the root and 1.6?mm at the cap is observed fusion zone; the interface and base metal microstructures have been examined using both optical and scanning electron microscopic techniques to understand the microstructural changes which have occurred due to laser welding. A range of tests of Vickers micro hardness, tensile and impact tests had been performed on the weldment to ascertain the mechanical properties of the joint. Tensile failure at the base metal and a 180° root bend test conducted on the weldment ascertain the soundness of the weld joint produced. An attempt is made to correlate the microstructure and mechanical properties of the weldment. Intermetallics TiN and Al₄C₃ observed in the SEM\EDS analysis at the fusion zone are found to have improved the weld metal strength and hardness.     

热处理对GH3128合金接头组织及力学性能的影响

 核能已经逐渐取代化石能源成为新一代能源,作为重要构件的高温气冷堆中间换热器得到了广泛关注。由于GH3128合金具有较好的焊接性、较高的高温抗氧化性能和组织稳定性,有望成为超高温气冷堆中间换热器的候选材料,但基于换热器结构复杂性以及密封性的要求,焊接是其生产和制造的关键成形手段。采用脉冲钨极氩弧焊(GTAW)对GH3128合金2 mm板材进行对接焊,研究了热处理对焊接焊接接头显微组织以及应力的影响。结果表明,在优化焊接工艺参数下,固溶态板材接头表现出最高的强塑性,室温及高温拉伸断裂位置均为母材。由于热轧态与固溶态板材接头热影响区在焊接过程中产生残余应力,导致该区硬化,在高温变形过程中残余应力诱发热影响区μ相析出,对接头持久、蠕变性能造成不利影响。焊后热处理消除了接头热影响区的残余应力,减少了持久、蠕变过程中μ相的析出,接头持久寿命得以改善。在1 200 ℃下,残余应力可为焊后热处理过程中静态再结晶提供激活能,接头热影响区发生再结晶,硬度下降,接头塑性变形能力不协调,导致室温拉伸与950 ℃拉伸断裂位置均为焊接接头。对固溶态板材试样进行不同的焊后热处理,EBSD扫描结果分析发现,接头经过1 100 ℃×10 min热处理后,残余应力明显消失,温度升高至1 140 ℃后,热影响区开始发生再结晶。     

Effect of Heat Input on Macro,Micro and Tensile Properties of Flux Cored Arc Welded Ferritic Stainless Steel Joints

This paper discusses the influence of Flux Cored Arc Welding Process parameters such as welding current, travel speed, voltage on bead profile, metallurgical and mechanical properties of welds of 2 mm thick 409M ferritic stainless steel sheets. The study reveals that, grain coarsening, volume fraction of martensite, hardness of heat affected zone and % of delta ferrite in ER 309 weld metal increases with increase in heat input. However, the results show that variation of heat input does not make any significant effect on tensile strength of the joint. Hence, welding parameters that provide uniform bead profile for the weld are recommended for fabrication.     

Gas Tungsten Arc Welding of 316L Austenitic Stainless Steel with UNS S32205 Duplex Stainless Steel

In the present work, dissimilar welding between UNS S32205 duplex stainless steel (DSS) and 316L austenitic stainless steel (ASS) was performed by using gas tungsten arc welding and ER2209 filler at two different heat inputs (0.52 and 0.98 kJ/mm). Microstructures were characterized using reflected light optical microscope and scanning electron microscope. Micro-hardness and tensile properties were measured across the weld for both the heat inputs. The microstructure of the welded region was primarily austenitic (for both heat inputs) with Widmanstätten morphology. The grain size of the heat affected zone on DSS side was very large (~200 µm) for the high heat input sample with the presence of partially transformed austenite and acicular austenite. The precipitation of intermetallic phases and carbides was not observed for both the heat inputs. The proportion of ferrite in the weld metal (as measured by feritscope) was higher for the high heat input sample than the low heat input sample. During the tensile test, fracture occurred in 316L ASS base metal (because of its lower strength) in ductile manner. For high heat input welds, the impact tested sample showed the presence of fine spherical precipitates rich in Cr, Mn and Fe in the fracture surface of weld metal.     

Evaluating the Properties of Dissimilar Metal Welding Between Inconel 625 and 316L Stainless Steel by Applying Different Welding Methods and Consumables

The current work was carried out to characterize welding of Inconel 625 superalloy and 316L stainless steel. In the present study, shielded metal arc welding (SMAW) and gas tungsten arc welding (GTAW) with two types of filler metals (ERNiCrMo-3 and ERSS316L) and an electrode (ENiCrMo-3) were utilized. This paper describes the selection of the proper welding method and welding consumables in dissimilar metal joining. During solidification of ERNiCrMo-3 filler metal, Nb and Mo leave dendritic cores and are rejected to inter-dendritic regions. However, ERSS316L filler metal has small amounts of elements with a high tendency for segregation. So, occurrence of constitutional super-cooling for changing the solidification mode from cellular to dendritic or equiaxed is less probable. Using GTAW with lower heat input results in higher cooling rate and finer microstructure and less Nb segregation. The interface between weld metal and base metal and also unmixed zones was evaluated by scanning electron microscopy and energy dispersive X-ray (EDX) analysis. Microhardness measurements, tensile test, and Charpy impact test were performed to see the effect of these parameters on mechanical properties of the joints.     

Microstructural and Mechanical Studies of T91/T22 Welded Joints

Comparative studies have been performed to decide an appropriate combination of welding process and filler material by virtue of microstructural evolution, micro-hardness studies, tensile strength and fractographic analysis. Manual arc welding and tungsten inert gas welding processes are used along with different filler materials to manufacture T91/T22 welded joints. Studies with the purpose of comparison and evaluation of different zones of the weldments have been carried out. The highest value of micro-hardness observed on the T91 HAZ of the weldments may be attributed to martensitic structure of the region. The fracture morphology of both the weldments obtained from T22 BM has revealed the ductile fracture. Comparatively higher tensile strength (578 MPa) of T91/T22, GTAW combination is noticed by virtue of lower heat input. The better performance of T91/T22, GTAW weldment can be quoted on the basis of better joint integrity, tensile strength and ductility (26.4%).     

Influence of Activating Flux and Helium Shielding Gas on an Austenitic Stainless Steel Weldment

Activating flux-assisted gas tungsten arc welding (GTAW) is a well-established method for enhancing weld penetration. In GTAW, steel is usually welded with a shielding gas that contains mostly argon. However, pure argon does not provide enough weld penetration. Argon-helium mixtures are inert and a greater concentration of helium would increase the arc voltage and the weld depth-to-width (D/W) ratio. There is a significant level of interest in the interaction between activating flux and shielding gas composition. Weld morphology, arc profile, retained δ ferrite content, angular distortion, and microstructure are extremely important in applying the activating flux combination argon-helium in GTAW; therefore, in this work, all these were studied.     

40CrNiMoA钢同质焊条焊接接头组织和性能研究

分析了焊接电流70A、80A、90A对40CrNiMoA钢焊缝接头组织和力学性能的影响。随着焊接电流的增大,焊缝外观质量较好。随着焊接电流的增大,熔池区温度升高,奥氏体晶粒尺寸增大,导致马氏体组织粗大。焊缝的显微组织为马氏体及少量残余奥氏体。焊缝的硬度远高于母材的硬度,且波动较大。热影响区的硬度从母材向沿焊缝方向逐渐升高。焊接接头纵向应力在焊缝中心为压应力,向外压应力减小。焊接颜色区边界处纵向应力为拉应力,且该点拉应力最大。焊接接头横向应力在焊缝中心为拉应力,向外逐渐增大,焊接颜色区边界处变横向拉应力达到最大。焊接电流和热输入增大,降低了材料的韧性,组织中铁素体增多及焊接残余应力是诱发脆性断裂的原因。焊接电流80A是40CrNiMoA同质焊条平板对接焊接工艺的最佳的焊接电流。     

Microstructure and Mechanical Properties of TWIP Steel Joints

As a new type of high manganese steel, the twinning induced plasticity （TWIP） steels have attracted a growing interest in the automotive industry due to their good performance. Thin plates of TWIP steel were welded by laser beam welding （LBW） and gas tungsten arc welding （GTAW）. The microstructure result shows that GTAW joint has obvious heat-affected zone （HAZ）, while the HAZ of LBW joint is almost invisible. The X-ray diffraction result shows that the phase compositions of both joints are austenitic and no phase transition occurs. Energy disper- sive spectrometry result shows that there is violent evaporation of Mn element in LBW joint, while the proportion of Mn element in GTAW joint is almost unchanged. Tensile tests and micro-hardness measurements were performed to take into account the mechanical properties of joints manufactured by the two different processes. The micro-hard- ness profiles of both joints present a typical saddle distribution, and the hardness of GTAW seam is lower than that of LBW seam. The failure positions of LBW joints are all located in base metal while the GTAW joints are all at the weld toe due to the softening of HAZ. By means of scanning electron microscopy, a typical ductile fracture is observed in LBW joint, while a brittle fracture with quasi-cleavage fracture characteristic is observed in GTAW joint.     

Application of GRA and TOPSIS Optimization Techniques in GTA Welding of 15CDV6 Aerospace Material

In this article, an attempt was made to optimize the welding parameters of gas tungsten arc welding of 15CDV6 steel. Experiments based on Taguchi’s L9 orthogonal array were carried out in this research paper. The input parameters such as current, voltage, travel speed were considered for joining 15CDV6 plates of thickness 3.7 mm. Aftermath, the welds were subjected to post weld heat treatment. The performance characteristics such as bead width, reinforcement, tensile strength, hardness and depth of penetration of the welds were also measured. Grey relational analysis (GRA) and technique for order preference by similarity to ideal solution method (TOPSIS) were used for identifying the optimised input parameters. Analysis of variance was used to identify the influence of each individual parameter on the multi-objective function. The metallurgical characterisations of the optimised weld were compared with the microstructures obtained using optical microscope. It was made clear that both GRA and TOPSIS produced different set of optimized parameters. But on experimentation, it was found that optimized parameters obtained from TOPSIS produced weld with better properties. At the initial stage, the base metal reflected inferior properties to weldments but there was a significant improvement in the properties of base metal after post weld heat treatment.     

Improvement of Metallurgical and Mechanical Properties of Gas Tungsten arc Weldments of Alloy 686 by Current Pulsing

This research article examines the metallurgical and mechanical behavior of twenty-first-century nickel-based superalloy 686. The weld joints were produced with ERNiCrMo-4 and ERNiCrMo-14 filler wires by continuous current gas tungsten arc welding (GTAW) and pulsed current gas tungsten arc welding (PCGTAW) mode. Optical and scanning electron microscope (SEM) analyses were performed to evaluate the microstructure of welded joints. PCGTAW weldments showed refined microstructure, narrower weld bead and minimum heat-affected zone compared to GTAW. SEM analysis revealed the presence of secondary phases in the interdendritic regions of GTA and PCGTA weldments made of ERNiCrMo-4 and GTA ERNiCrMo-14 fillers. Energy-dispersive X-ray spectroscopy examination was also performed to assess the microsegregation of alloying elements in the weldments. The results proved nonexistence of microsegregation in the case of PCGTA weldments made by ERNiCrMo-14 filler. However, segregation of alloying element Mo was noticed in other weldments. Strength and toughness of the weld joints were evaluated by conducting tensile and Charpy impact tests. The refined microstructure with the absence of microsegregation obtained in the PCGTA welding made with ERNiCrMo-14 filler wire resulted in the higher strength and toughness than other weldments.     

K-TIG焊接中厚板的工艺窗口改进

针对穿孔深熔氩弧焊(K-TIG)工艺焊接8 mm厚Q235低碳钢板时焊接过程不稳定、焊接工艺窗口小等突出问题,首次提出在焊接工件背部铺加保护焊剂的方法改善焊接过程。采用对接焊的方式,在不开坡口、焊接过程不添加焊丝的情况下,达到单面焊双面成形的效果。最终成功的采用430～480 A范围内的直流电流对8 mm厚的Q235低碳钢进行了焊接,将焊接电流窗口扩大到50 A同时也显著的提高了焊接过程的稳定性。同时,在扩大焊接电流窗口之后,系统研究了不同焊接电流下焊接接头的组织性能。研究结果表明:在不同焊接电流下得到的焊接接头中,组织分布以及力学性能分布呈现出相同的状态。焊缝区的组织均由铁素体+珠光体+魏氏组织组成;熔合区由魏氏组织组成;热影响区由铁素体+少量的珠光体组成;此外随着焊接电流的增加,焊接接头背部的熔宽有略微增加;在焊接接头中,熔合区处硬度值最高,其次是焊缝区,之后是热影响区,母材的硬度值最低;焊接接头最终的拉伸断裂位置是在热影响区处。      

Laser Welding of Ultra-Fine Grained Steel SS400

Steeliswidelyusedbecauseofitsgoodcompre hensive properties ,plentyofresourceandlowerprice .Thestrengthandtoughnessaretwoimpor tantpropertiesofsteels ,andpeoplemakeeffortstoincreasetheirvalues .Addingalloyingelementandcontrollingmicrostructurearetwobasicwaystoac complishtheaim .Therefinedmicrostructureob tainedbyprocessingtechniqueenablesthestrengthandtoughnessofsteeltobeincreasedwithoutaddingalloyingelementandtheratioofperformance costtobeincreased .Theultra finegrainedsteelshavefer ritegrains…     

Comparative Study on Processing Property Between CWW CO2 Gas Shielded Welding and SAW

 Cable welding wire (CWW) CO2 gas shielded welding is an innovative process arc welding with high efficiency, high quality and low consumption, in which cable wire is used as consumable electrode. CWW CO2 gas shielded welding and submerged arc welding (SAW) are used for contrast studies on processing property of high strength steel A36 used in ship structure. The results show that the shapes of weld seam, using CWW CO2 gas shielded welding and SAW, are good and no weld defect such as air hole, flaw, slag inclusion, incomplete fusion, lack of penetration and so on are found in the weld seam. Because the rotating of arc during CWW CO2 gas shielded welding process has a strong stirring effect on molten pool, the grain in the heat affected zone (HAZ) of the joints, using CWW CO2 gas shielded welding, is small. Tensile failure positions of joints by CWW CO2 gas shielded welding and SAW are all in the base metal, but tensile strength of CWW CO2 gas shielded welding joint is higher than that of SAW joint by an average of 2. 3%. The average impact energy of HAZ, using CWW CO2 gas shielded welding and SAW, is almost equal, but the average impact energy of the weld seam using CWW CO2 gas shielded welding is increased by 6%, and the average impact energy of the fusion line is increased by 7%. The 180° bending tests for the joints of CWW CO2 gas shielded welding and SAW are all qualified, and the joints hardness is all less than HV 355, but hardness of CWW CO2 gas shielded welding wire welding joint near the fusion line is obviously lower. It can be concluded that the properties of CWW CO2 gas shielded welding are better than those of the SAW joint, and CWW CO2 gas shielded welding is suitable for welding high strength steel A36 used in ship structure.     

Characterization of Structure–Property Relationship of Incoloy 825 and SAF 2507 Dissimilar Welds

This study was carried out to investigate the evaluation of dissimilar welding between Incoloy 825 Ni-based alloy and SAF 2507 super duplex stainless steel. Welding was conducted by pulsed current (PC) and continuous current (CC) gas tungsten arc welding (GTAW) methods using ERNiCrMo-3 filler wire. The microstructure of weld zones and base metal/weld interfaces as well as mechanical properties of weldments were characterized. The results detailed the formation of Nb, and Mo-rich phases in the inter-dendritic regions of weld metals leading to a decrease in impact resistance of weld zones in comparison to parent metals. Presence of more secondary phases at the CCGTA weld metal resulted in higher hardness and lower toughness than that of the PCGTAW sample. During tensile tests, fracture occurred at the Incoloy 825 base metal, and both weldments also underwent ductile mode of fracture. The research addressed the microstructure–property relationship for dissimilar weld joints.