One‐Step Preparation of Pt on Pretreated Multiwalled Carbon Nanotubes for Methanol Electrooxidation

For the first time, intermittent microwave heating (IMH) is a one‐step technique applied to pretreat the multiwalled carbon nanotubes (MWCNTs) in H₂O₂ solution. The approach does not require washing and filtration of the sample, thus significantly reducing the loss of the material and treatment time. The IMH associated with H₂O₂ treatment, is optimised to fabricate efficient support for Pt electrocatalyst. Both as‐received and treated MWCNTs are used as Pt electrocatalyst supports, respectively. It demonstrates that the treated MWCNTs supported Pt has much better electrocatalytic performance than that of untreated MWCNTs supported Pt. The Pt on MWCNTs treated with an IMH irradiation mode in 10 s on and 20 s off for 5 times, shows the best performance for methanol oxidation. This work provides a novel approach to simply and economically fabricate an efficient MWCNT support at a large scale, for high performance Pt electrocatalysts.     

Preparation and Properties of Submicrometer‐Sized LLM‐105 via Spray‐Crystallization Method

Submicrometer‐sized 2,6‐diamino‐3,5‐dinitropyrazine‐1‐oxide (LLM‐105) crystals were prepared by spray‐crystallization method with dimethyl sulfoxide (DMSO) and ultra‐pure water with surfactant as the solvent and anti solvent, respectively. Submicrometer‐sized LLM‐105 particles were characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD), and particle size analysis. The thermal stability and sensitivity properties of submicrometer‐sized LLM‐105 were also investigated. The results revealed that the submicrometer‐sized LLM‐105 particles are spherelike in morphology with a narrow particle size distribution at the range of 100–600 nm. The submicrometer‐sized LLM‐105 has a lower exothermic peak at about 343.7 °C compared with the synthesized material. Sensitivity tests showed that submicrometer‐sized LLM‐105 is more insensitive under impact stimulus with a drop height (H₅₀) of 102 cm. The submicrometer‐sized LLM‐105‐based PBX is more sensitive for short impulse shock wave that can be initiated at lower initiation current.     

Investigations of Compositions and Performance of PtRuMo/C Ternary Catalysts for Methanol Electrooxidation

PtRuMo/C catalyst was prepared by impregnation reduction method and characterised. Comparison is made between a home‐made PtRu/C prepared by similar method and Pt/C (E‐Tek Co., Pt/C‐ET) catalysts. One glassy carbon disc electrode for ternary alloy catalyst was used to evaluate the catalytic performances by cyclic voltammetric, chronoamperometric, amperometric i–t curves, and electrochemical impedance spectra (EIS). The electrochemical measurement results indicated that the performance of PtRuMo/C with a molar ratio of 6:3:1 was the highest among 15 Pt_xRu_yMo_10–x–y/C catalysts with different molar ratios. The composition, particle size, lattice parameter and morphology of the PtRuMo(6:3:1)/C catalyst were determined by means of X‐ray energy dispersive analysis, X‐ray diffraction (XRD) and transmission electron micrographs (TEM). The result of XRD analysis exhibits that PtRuMo(6:3:1)/C has the fcc structure with the smaller lattice parameter than the home‐made PtRu/C and Pt/C‐ET. Its typical particle sizes is only about 5 nm. With respect to the catalytic activity and stability, the PtRuMo(6:3:1)/C catalyst is superior to PtRu/C despite their comparable active areas. Though the electrochemically active surface area of Pt/C‐ET is the biggest, its performance is the lowest. EIS results also indicate that the reaction resistances for methanol electrooxidation on the PtRuMo(6:3:1)/C catalyst are smaller than those of PtRu/C at different polarisation potentials.     

Evaluation of the Performance of Carbon Supported Pt–Ru–Ni–P as Anode Catalyst for Methanol Electrooxidation

This research is aimed to improve the activity and stability of ternary alloy Pt–Ru–Ni/C catalyst. A novel anodic catalyst for direct methanol fuel cell (DMFC), carbon supported Pt–Ru–Ni–P nanoparticles, has been prepared by chemical reduction method by using NaH₂PO₂ as a reducing agent. One glassy carbon disc working electrode is used to test the catalytic performances of the homemade catalysts by cyclic voltammetric (CV), chronoamperometric (CA) and amperometric i–t measurements in a solution of 0.5 mol L^–1 H₂SO₄ and 0.5 mol L^–1 CH₃OH. The compositions, particle sizes and morphology of home‐made catalysts are evaluated by means of energy dispersive analysis of X‐ray (EDAX), X‐ray diffraction (XRD) and transmission electron micrographs (TEM), respectively. TEM images show that Pt–Ru–Ni–P nanoparticles have an even size distribution with an average diameter of less than 2 nm. The results of CV, CA and i–t curves indicate that the Pt–Ru–Ni–P/C catalyst shows significantly higher activity and stability for methanol electrooxidation due to the presence of non‐metal phosphorus in comparison to Pt–Ru–Ni/C one. All experimental results indicate that the addition of non‐metallic phosphorus into the Pt–Ru–Ni/C catalyst has definite value of research and practical application for enhancing the performance of DMFC.     

Synthesis of Truncated‐Octahedral Pt–Pd Nanocrystals Supported on Carbon Black as a Highly Efficient Catalyst for Methanol Oxidation

A novel PtPd/C nanocrystals catalyst with truncated‐octahedral structure has been successfully prepared by ethylene glycol reduction to induce anisotropic growth in an isotropic medium by adding a small amount of Fe³⁺ species. Its structure, composition, and morphology are characterized by X‐ray diffraction, transmission electron microscopy, and scanning transmission electron microscopy‐energy dispersive spectroscopy elemental maps, respectively. The electrochemical measurements demonstrate that the highly dispersed and uniform PtPd/C nanocrystals have excellent poisoning tolerance, significantly higher electrocatalytic activity and durability for the methanol oxidation, as compared to solid solution PtPd/C and Pt/C catalysts. This may be ascribed to the stepped atoms and dangling bonds, which served as active sites for breaking chemical bonds during oxidation–reduction reaction; the high density of preferred crystal planes of (111) facets greatly enhanced the oxidation of poisonous residues during reaction.     

Efficient Anchorage of Palladium Nanoparticles on the Multi‐Walled Carbon Nanotubes as Electrocatalyst for the Hydrazine Electrooxidation in Strong Acidic Solutions

A facile homogeneous precipitation–reduction reaction method, which involves PdCl₂ → PdO · H₂O → Pd⁰ reaction path, is used to synthesize the multi‐walled carbon nanotubes (MWCNTs) supported Pd nanoparticles (Pd/MWCNTs) catalysts. The particle size of Pd/MWCNTs catalysts can be easily tuned by controlling the hydrolysis temperature of PdCl₂. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) measurements show the particle size of Pd/MWCNTs catalysts increases with hydrolysis temperature of PdCl₂, which is ascribed to the fact that the particle size of PdO · H₂O nanoparticles increases with hydrolysis temperature of PdCl₂. At the lower hydrolysis temperature, the as‐prepared Pd/MWCNTs catalyst possesses the higher dispersion and the smaller particle size. Consequently, the resultant Pd/MWCNTs catalyst exhibits the big electrochemical active surface area and the excellent electrocatalytic performance for hydrazine electrooxidation in strong acidic solutions. In addition, the electrochemical measurement indicate that particle size effect of Pd‐NPs occurs during the N₂H₄ electrooxidation. In brief, the mass activity and specific activity of the Pd/MWCNTs catalyst increases and decreases with decreasing the particle size of Pd‐NPs for the N₂H₄ electrooxidation, respectively.     

A Novel Radial‐Flow,Spherical‐Bed Reactor Concept for Methanol Synthesis in the Presence of Catalyst Deactivation

A radial‐flow, spherical‐bed reactor concept for methanol synthesis in the presence of catalyst deactivation, has been proposed. This reactor configuration visualizes the concentration and temperature distribution inside a radial‐flow packed bed with a novel design for improving reactor performance with lower pressure drop. The dynamic simulation of spherical multi‐stage reactors has been studied in the presence of long‐term catalyst deactivation. Model equations were solved by the orthogonal collocation method. The performance of the spherical multi‐stage reactors was compared with a conventional single‐type tubular reactor. The results show that for this case study and with similar reactor specifications and operating conditions, the two‐stage spherical reactor is better than other alternatives such as single‐stage spherical, three‐stage spherical and conventional tubular reactors. By increasing the number of stages of a spherical reactor, one increases the quality of production and decreases the quantity of production.     

Elaboration of Ultra‐High Molecular Weight Polyethylene/Carbon Nanotubes Electrospun Composite Fibers

Micron‐sized fibers of UHMWPE reinforced with CNT were fabricated by the electrospinning process. Conditions for a metastable mutual solution of UHMWPE and CNTs were found at elevated temperature. These solutions were used for electrospining using a device having controlled temperature and gaseous environment around the electrospun liquid jet. The fabricated micron‐sized fibers exhibited the reinforcing CNTs as self‐organized nano‐ropes embedded within them. A post‐spinning drawing process enhanced the mechanical properties of the composite fibers to the level of 6.6 GPa strength and elongation at break of 6%. The CNT nano‐ropes form spontaneously in the liquid jet during electrospinning, and provide the reinforcement framework which is amenable for post‐drawing of the fibers for subsequent utilization as composite nanofibers. The experimental results exhibit the highest strength value reported to date for electrospun fibers.

     

Cellulose‐Derived Carbon Fibers with Improved Carbon Yield and Mechanical Properties

The manufacture of high mechanical strength cellulose‐based carbon fibers (CFs) is accomplished in a continuous process at comparably low temperatures and with high carbon yields. Applying a sulfur‐based carbonization agent, i.e., ammonium tosylate (ATS), carbon yields of 37% (83% of theory), and maximum tensile strengths and Young's moduli up to 2.0 and 84 GPa are obtained already at 1400 °C. For comparison, the use of the well‐known carbonization aid ammonium dihydrogenphosphate ((NH₄)H₂PO₄), ADHP, is also investigated. Both the precursor and the CFs are characterized via elemental analysis, wide‐angle X‐ray scattering, Raman spectroscopy, scanning electron microscopy, and tensile testing. Thermogravimetric analysis coupled with mass spectrometry/infrared spectroscopy discloses differences in structure formation between ATS and ADHP‐derived CFs during pyrolysis.     

活性炭纤维的开发与应用

介绍了活性炭纤维的发展状况、合成方法、及性能与应用。     

Study of the Characteristics of Methanol Synthesis in a Recirculation Slurry Reactor – A Novel Three‐Phase Synthesis Reactor

A process feasibility analysis on the liquid phase methanol synthesis (LPMeOH^TM) process was performed in a recirculation slurry reactor (RSR). In the three‐phase RSR system, a fine catalyst is slurried in the paraffin and this catalyst slurry is continuously recirculated through the nozzle from the slurry sector to the entrained sector by a pump. The syngas is fed concurrently with the downward flow of slurry to form the methanol product. A laboratory scale mini‐pilot plant version of a recirculation slurry reactor system was successfully designed and built to carry out process engineering research, and in addition, an identical cold model was built to measure the mass transfer coefficient in the recirculation slurry reactor. The effects of operating conditions, including temperature, pressure, gas flow rate and catalyst slurry recirculation flow rate on the productivity of methanol were studied. This experimental data helps the scale‐up and commercialization of the methanol synthesis process in recirculation slurry reactors.     

Operation Characteristic Analysis of a Direct Methanol Fuel Cell System Using the Methanol Sensor‐less Control Method

The application of methanol sensor‐less control in a direct methanol fuel cell (DMFC) system eliminates most of the problems encountered when using a methanol sensor and is one of the major solutions currently used in commercial DMFCs. This study focuses on analyzing the effect of the operating characteristics of a DMFC system on its performance under the methanol sensor‐less control as developed by Institute of Nuclear Energy Research (INER). Notably, the influence of the dispersion of the methanol injected on the behavior of the system is investigated systematically. In addition, the mechanism of the methanol sensor‐less control is investigated by varying factors such as the timing of the injection of methanol, the cathode flow rate, and the anode inlet temperature. These results not only provide insight into the mechanism of methanol sensor‐less control but can also aid in the improvement and application of DMFC systems in portable and low‐power transportation.     

Ultraporous Palladium Supported on Graphene‐Coated Carbon Fiber Paper as a Highly Active Catalyst Electrode for the Oxidation of Methanol

Ultraporous Pd nanocrystals for electrocatalysis applications were fabricated using a direct electrodeposition method on three differing carbon supports: flexible carbon fiber paper (CFP), and CFP modified with either graphene oxide nanosheets or their chemically reduced forms using a simple spray coating technique. The electrocatalytic activity of these electrodes was investigated for the direct electro‐oxidation reaction of methanol in alkaline media. Pd deposited on the CFP modified with reduced graphene oxide (rGO) has excellent poisoning tolerance to carbonaceous species and a significantly better catalytic activity toward methanol oxidation than the other two catalyst support materials. Pd/rGO/CFP in 2.0 M CH₃OH in 2.0 M NaOH yields a specific current density of 241 mAmg^–1 cm^–2 determined at the anodic oxidation peak. It is believed that the collaborative effects due to the three‐dimensional ultraporous Pd nanocrystals and fast electron transfer owing to high conductivity of rGO nanosheets play an important role in enhancing the catalytic performance of Pd/rGO/CFP toward methanol oxidation in alkali media.     

Increased Metal Utilization in Carbon‐Supported Pt Catalysts by Adsorption of Preformed Pt Nanoparticles on Colloidal Silica

Pt/C electrocatalysts, aimed at maximizing the electrochemical surface area (ECSA) and consequently the specific mass activity of fuel cell reactions, are obtained by firstly depositing Pt nanoparticles on colloidal silica (Pt‐silica), followed by the adsorption of the latter onto a carbon support. This method of catalyst preparation increases Pt metal utilization and generates accessible void space in the interpenetrating particle network of carbon and silica for the facile transport of reactants and products. Both electrochemical hydrogen adsorption/desorption and CO oxidation measurements show an increase in the ECSA using this approach. Methanol electrooxidation is used as a test reaction to evaluate the catalytic activity. It is found that the silica modified catalyst is three times as active as a catalyst prepared without silica, under otherwise identical conditions.     

Fluid‐Induced Alignment of Carbon Nanofibers in Polymer Fibers

Carbon nanofiber/polycaprolactone (CNF/PCL) composite fibers are fabricated using a microfluidic approach. The fibers are made with different content levels of CNFs and flow rate ratios between the core and sheath fluids. The electrical conductivity and tensile properties of these fibers are then investigated. It is found that at a CNF concentration of 3 wt%, the electrical conductivity of the composite fiber significantly increases to 1.11 S m⁻¹. The yield strength, Young's modulus, and ultimate strength of the 3 wt% CNF increase relative to the pure PCL by factors of 1.72, 2.88, and 1.23, respectively. Additionally, the results show that a microfluidic approach can be considered as an effective method to align CNFs along the fibers in the longitudinal direction.

     

Synthesis of Mesoporous Carbon from Okara and Application as Electrocatalyst Support

Carbon materials derived from biomass are economical and simple. Here, a okara‐derived carbon (ODC) was prepared by carbonized cheap and abundant okara at 800 °C in N₂ atmosphere. A high degree of graphitization, mesoporous structure and large specific surface area of ODC were proved by Raman spectroscopy, nitrogen adsorption–desorption isotherms, X‐ray diffraction, Fourier transform infrared spectra and scanning electron microscope. The ODC can be used as support of platinum nanoparticles, and the catalytic performance for methanol electro‐oxidation of its was measured by cyclic voltammetry and CO stripping voltammetry. The results showed that Pt/ODC catalyst had higher electrocatalytic activity and the resistance to poisoning ability toward methanol electrooxidation than the Pt/C catalyst prepared under the same conditions.     

Surface Modification of Carbon Fibers by Free Radical Graft‐Polymerization of 2‐Hydroxyethyl Methacrylate for High Mechanical Strength Fiber–Matrix Composites

Free radical polymerization of vinylic monomers in the presence of carbon fibers results in the grafting of polymers onto the carbon fiber surface. Graft polymers cannot be removed by intense washing with good polymer solvents. The density and size of these structures are successfully controlled by reaction conditions. Grafting of the carbon fiber surface with hydroxyethyl methacrylate allows for introducing functional groups suitable for the reaction with an epoxy‐based resin. The resulting fiber‐reinforced composites show enhanced mechanical properties compared to samples prepared from carbon fibers equipped with a standard sizing for epoxy resins. Thus, tensile strength increases by 10%, while interlaminar shear strength improves by 20%.     

Fabrication of Ultrahigh‐Strength Polybenzimidazole Fibers via a Novel and Green Integrated Liquid Crystal Spinning Process

Herein, the first example of ultrahigh‐strength polybenzimidazole (PBI) fibers using a PBI solution in liquid crystal state is reported via a novel and green integrated spinning technology. Microwave‐assisted polycondensation is utilized to synthesize the polybenzimidazole/polyphosphoric acid liquid crystal spinning solution and pure water is employed as the coagulating and washing bath to afford a green fabrication process. The green integrated spinning technology is eco‐friendly, cheap, and conducive for the large‐scale production of PBI fibers. The as‐prepared PBI fibers display superb flame retardancy, and the outstanding thermal stability of PBI fiber enables it to preserve structural integrity at temperatures as high as 600 °C. More significantly, it prepared the ultrahigh‐strength of PBI fiber up to 0.91 GPa, which is two times than that of the reported PBI fibers, marking a significant breakthrough for the high‐performance PBI fibers.     

Enhanced Strain Sensing Performance of Polymer/Carbon Nanotube‐Coated Spandex Fibers via Noncovalent Interactions

Over the past decade, flexible strain sensors have been of tremendous interest due to their wide application in robotics, medical diagnostics, human motion detection, and healthcare. Herein, a fiber strain sensor is fabricated by continuously coating a layer of ultrathin multi‐walled carbon nanotube (MWCNT)/thermoplastic polyurethane (TPU) nanocomposites onto the surface of commercial spandex fiber. The effect of noncovalent functionalization of MWCNTs using 1‐pyrenecarboxylic acid (PCA) on the electrical conductivity as well as the sensing performance of the fiber sensor is investigated. The low‐cost strain sensor possesses a large workable strain (up to 200% strain), high sensitivity (gauge factor is 14 191.5 under 170–200% strain), and excellent stability (up to 1000 cycles), and regular signal responses within a wide measuring frequency range of 0.01–1 Hz are achieved with the introduction of PCA via enhanced nanotube dispersion and polymer–nanofiller interactions. Additionally, the resistance response to strain is fitted with a model based on tunneling theory to understand the sensing mechanism, and to prove that the fitted results are in agreement with the experimental results. Furthermore, the developed sensor is successfully applied in human motion detection, such as joint movement, facial microexpressions, and speech recognition.