整体化色谱柱分离测定甘草酸18H-差向异构体

建立整体化色谱柱分离分析甘草酸18H-差向异构体的方法。采用C18整体化色谱柱,流动相为磷酸盐缓冲液-乙腈体系,探讨了磷酸盐缓冲液pH及浓度、乙腈含量、柱温等对甘草酸18H-差向异构体分离的影响,在优化色谱条件下,18α-、18β-甘草酸得到基线分离,分离度可达2.75,二异构体出峰时间在10 min内,且在2.12～21.2μg/mL范围内线性关系良好。运用整体化色谱柱缩短了甘草酸18H-差向异构体的分析时间,提高了分析效率,方法可运用于评价甘草酸的异构化及质量控制。     

Determination of trace macrolide antibiotics in milk with online solid‐phase extraction with an ionic‐liquid‐based monolithic column

An ionic liquid (IL)‐based monolithic poly(ionic liquid glycidylmethacrylate‐co‐ethylene glycol dimethacrylate) column was prepared via in situ free‐radical polymerization with 1‐vinyl‐3‐butylimidazolium chlorine as one of the comonomers. The obtained monolithic column was used as the sorbent of solid‐phase extraction (SPE) and coupled with high‐performance liquid chromatography for the simultaneous determination of the macrolide antibiotics roxithromycin (ROX) and acetylspiramycin (ACE) in processed pure milk. The monolithic column was characterized by Fourier transform infrared spectrometry, scanning electron microscopy, nitrogen absorption–desorption, mercury intrusion porosimetry, and thermogravimetric analysis. The results reveal that the monolithic column exhibited a high selectivity and good permeability to the macrolide antibiotics in milk. The optimized method offered excellent linearity with a linear regression coefficient greater than 0.998. The precisions for interday and intraday were both less than 7.7%. The accuracies expressed by the recoveries for ROX and ACE were in the ranges 92.5–103.8 and 93.0–107.6%, respectively. Compared to the previous methods, this method had a low limit of detection and a good accuracy. As a result, the polymer IL based monolithic column could feasibly be used as a high‐selectivity online SPE sorbent for determining trace macrolide antibiotics in milk. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43943.     

Removal of carbon dioxide from flue gases in packed column using ionic liquids

The study of CO₂ absorption in ionic liquids (ILs): [Emim] [Ac], [Bmim] [Ac] in a packed column is presented. The influence of mass transfer resistances, initial CO₂ concentration, absorption temperature and 2, 5, 10% wt. water addition on CO₂ removal efficiency was investigated. The resistance in series model and estimated values of enhancement factor were used to predict with good accuracy mass fluxes of absorbed carbon dioxide for both ILs. The CO₂ absorption efficiency in packed column depends on temperature and initial CO₂ concentration. The addition of small amounts of water to [Emim][Ac] is of minor effect on CO₂ absorption.     

A one‐pot method to prepare transparent poly(methyl methacrylate)/montmorillonite nanocomposites using imidazolium‐based ionic liquids

Poly(methyl methacrylate) (PMMA)/montmorillonite (MMT) nanocomposites were prepared by a new one‐pot technique, where the hydrophilic Na‐MMT layers were decorated with hydrophobic 1‐dodecyl‐3‐methylimidazolium hexafluorophosphate (C₁₂mimPF₆) ionic liquid in situ during melt blending with PMMA and intercalation of polymer chains took place subsequently. The in situ modification and intercalation of Na‐MMT were confirmed using X‐ray diffraction and transmission electron microscopy. The combination of the compatible C₁₂mimPF₆ with PMMA and the good dispersion of MMT layers at the nanoscale rendered the resultant PMMA/MMT nanocomposites with improved optical transparency, thermal stability and mechanical properties. Copyright © 2012 Society of Chemical Industry     

Structure‐based model for prediction of electrical conductivity of pure ionic liquids

A structure‐based method was proposed to estimate the electrical conductivity of ionic liquids covering wide ranges of temperature (238.15–484.1 K) and electrical conductivity (0.0001524–19.3 S/m) based on experimental data collect from literature from 1998 to 2015. The influences of temperature and ion structure on electrical conductivity were also discussed. The mean absolute percentage error between the calculated and literature data was 6.02%, with 6.12% for the training set (1978 data points, 177 ILs) and 5.10% for the test set (217 data points, 11 ILs). © 2016 American Institute of Chemical Engineers AIChE J, 62: 3751–3762, 2016     

Evaluation of 1‐ethyl‐3‐methylimidazolium acetate based ionic liquid systems as a suitable solvent for collagen

Collagen, a prominent biopolymer, which is famous for its excellent biological activity, has been used extensively for tissue engineering applications. In this study, a novel solvent system for collagen was developed with an ionic liquid, 1‐ethyl‐3‐methylimidazolium acetate ([EMIM][Ac]), solvent system. A series of sodium salts were introduced into this solvent system to enhance collagen's dissolution procedure. The results show that the solubility of collagen was significantly influenced by the temperature and sodium salts. The solubility reached up to approximately 11% in the [EMIM][Ac]/Na₂HPO₄ system at 45°C. However, the structure of the regenerated collagen (Col‐regenerated) may have been damaged. Hence, we focused on the structural integrity of the collagen regenerated from the [EMIM][Ac] solvent system by the methods of sodium dodecyl sulfate–polyacrylamide gel electrophoresis, Fourier transform infrared spectroscopy, ultrasensitive differential scanning calorimetry, atomic force microscopy, X‐ray diffraction, and circular dichroism because its signature biological and physicochemical properties were based on its structural integrity. Meanwhile, a possible dissolution mechanism was proposed. The results show that the triple‐helical structure of collagen regenerated from the [EMIM][Ac] solvent system below 35°C was retained to a large extent. The biocompatibility of Col‐regenerated was first characterized with a fibroblast adhesion and proliferation model. It showed that the Col‐regenerated had almost the same good biological activity as nature collagen, and this indicated the potential application of [EMIM][Ac] in tissue engineering. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2245–2256, 2013     

A new fragment contribution‐corresponding states method for physicochemical properties prediction of ionic liquids

A new fragment contribution‐corresponding states (FC—CS) method based on the group contribution method and the corresponding states principle is developed to predict critical properties of ionic liquids (ILs). There are 46 fragments specially classified for ILs considering the ionic features of ILs, and the corresponding fragment increments are determined using the experimental density data. The accuracy of the developed method is verified indirectly via predicting density and surface tension of ILs. The results show that the FC—CS method is reasonable with an average absolute relative deviation less than 4%. With the calculated critical properties, corresponding states heat capacity (CSHC) and corresponding states thermal conductivity (CSTC) correlations are proposed to predict heat capacity and thermal conductivity of ILs, respectively. The predicted results agreed well with the experimental data. The proposed FC—CS method and the two corresponding states correlations are important for design, simulation, and analysis of new ionic liquid processes. © 2012 American Institute of Chemical Engineers AIChE J, 59: 1348–1359, 2013     

Influence of acetated‐based and bromo‐based ionic liquids treatment on wool dyeing with acid blue 7

Bromo‐based and acetated‐based ionic liquids (ILs), 1‐butyle‐3‐methylimidazolium bromo ([Bmim]Br), 1‐ethyl‐3‐mthylimidazolium bromo ([Emim]Br), 1‐butyle‐3‐methylimidazolium acetate ([Bmim]Ac), and 1‐ethyl‐3‐mthylimidazolium acetate ([Emim]Ac), were synthesized and employed for wool surface treatment. Scanning electron microscope results indicated that the wool surfaces treated with acetated‐based ILs were eroded more than those treated with bromo‐based ILs. Comparable studies showed that the wool samples treated with acetate‐based ILs, especially [Emim]Ac, had higher initial dyeing rate and equilibrium exhaustion than those with bromo‐based ILs. Along with treatment temperature and time increasing, acetate‐based ILs had more remarkable effects on mechanical and dyeing properties of the wool samples than bromo‐based ILs. The wool samples treated with [Emim]Ac at 60°C for 10 min had excellent low‐temperature dyeing properties. The color depth (K/S) investigations showed that the wool samples treated with acetate‐based ILs possessed darker color depth than those treated with the bromo‐based ILs. Color fastnesses of the wool samples treated with [Bmim]Br, [Emim]Br and [Bmim]Ac exhibited the same grades as the untreated sample, while wet color fastnesses of [Emim]Ac treated sample were slightly decreased. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

In situ thermal polymerization of an ionic liquid monomer for quasi‐solid‐state dye‐sensitized solar cells

In situ thermal polymerization of a model ionic liquid monomer and ionic liquids mixture to form gel electrolytes is developed for quasi‐solid‐state dye‐sensitized solar cells (Q‐DSSCs). The chemical structures and thermal property of the monomers and polymer are investigated in detail. The effect of iodine concentration on the conductivity and triiodide diffusion of the gel electrolytes is also investigated in detail. The conductivity and triiodide diffusion of the gel electrolytes increase with the increasing I₂ concentration, while excessive I₂ contents will decrease the electrical performances. Based on the in situ thermal polymeric gel electrolytes for Q‐DSSCs, highest power conversion efficiency of 5.01% has been obtained. The superior long‐term stability of fabricated DSSCs indicates that the cells based on in situ thermal polymeric gel electrolytes can overcome the drawbacks of the volatile liquid electrolyte. These results offer us a feasible method to explore new gel electrolytes for high‐performance Q‐DSSCs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42802.     

Molecularly imprinted polymers for the selective recognition of l‐phenylalanine based on 1‐buty‐3‐methylimidazolium ionic liquid

To enhance the affinity of 4‐vinyl pyridine to l ‐phenylalanine (l ‐Phe) and convert the imprinting process from the aqueous phase to the organic phase, an oil‐soluble amino acid ionic liquid was introduced as a template. In this study, 1‐butyl‐3‐methylimidazolium α‐aminohydrocinnamic acid salt was first applied to prepared surface molecularly imprinted polymers (MIPs) in acetonitrile for the selective recognition of l ‐Phe. Fluorescence quenching analysis of the functional monomer on the template was investigated under different conditions to study the imprinting mechanism. Several binding studies, such as the sorption kinetics, sorption thermodynamics, and solid‐phase extraction application, and the chiral resolution of racemic phenylalanine were investigated. The binding isotherms were fitted by nonlinear regression to the Freundlich model to investigate the recognition mechanism. The affinity distribution analysis revealed that polymers imprinted by ionic liquid showed higher homogeneous binding sites than those imprinted by l ‐Phe. The competition tests were conducted by a molecularly imprinting solid‐phase extraction procedure to estimate the selective separation properties of the MIPs for l ‐Phe. The target MIP was shown to be successfully for the separation of l ‐Phe from an amino acid mixture. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42485.     

Influence of a rigid polystyrene block on the free volume and ionic conductivity of a gel polymer electrolyte based on poly(methyl methacrylate)‐block‐polystyrene

Diblock copolymers poly(methyl methacrylate)‐block‐polystyrene with three different molar ratios [poly(methyl methacrylate)/polystyrene (PS) = 1:1, 1:1.5, and 1:1.8] were synthesized by atom transfer radical polymerization and used as a polymer matrix for gel polymer electrolytes (GPEs). The positron annihilation lifetime spectroscopy was applied to determine the free‐volume behaviors of different GPEs, respectively. We illustrated that a proper PS ratio may led to the formation of a high fraction of free volume, and the influence of the PS ratio on the free‐volume fraction was caused by the different morphologies of the GPEs because of the different packing densities of the PS rigid block. The ionic conductivity was correlated with the free volume in the GPE through the study of the ionic conductivity dependence on the temperature; this followed the Vogel–Tamman–Fulcher equation. Moreover, an ionic conductive model was proposed, in which variations of the free‐volume behavior provide different ionic‐conducting abilities. Thermogravimetric analysis indicated that GPEs based on different block copolymers exhibited high liquid‐electrolyte preservation properties. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43901.     

Methods for stabilizing and activating enzymes in ionic liquids—a review

Ionic liquids (ILs) have evolved as a new type of non‐aqueous solvents for biocatalysis, mainly due to their unique and tunable physical properties. A number of recent review papers have described a variety of enzymatic reactions conducted in IL solutions; on the other hand, it is important to systematically analyze methods that have been developed for stabilizing and activating enzymes in ILs. This review discusses the biocatalysis in ILs from two unique aspects (1) factors that impact the enzyme's activity and stability, (2) methods that have been adopted or developed to activate and/or stabilize enzymes in ionic media. Factors that may influence the catalytic performance of enzymes include IL polarity, hydrogen‐bond basicity/anion nucleophilicity, IL network, ion kosmotropicity, viscosity, hydrophobicity, the enzyme dissolution, and surfactant effect. To improve the enzyme's activity and stability in ILs, major methods being explored include the enzyme immobilization (on solid support, sol–gel, or CLEA), physical or covalent attachment to PEG, rinsing with n‐propanol methods (PREP and EPRP), water‐in‐IL microemulsions, IL coating, and the design of enzyme‐compatible ionic solvents. It is exciting to notice that new ILs are being synthesized to be more compatible with enzymes. To utilize the full potential of ILs, it is necessary to further improve these methods for better enzyme compatibility. This is what has been accomplished in the field of biocatalysis in conventional organic solvents. Copyright © 2010 Society of Chemical Industry     

Gas solubility in long‐chain imidazolium‐based ionic liquids

The gas solubility in 1‐dodecyl‐3‐methylimidazolium [C₁₂MIM] based ionic liquids (ILs) was measured at temperatures (333.2, 353.2, and 373.2) K and pressures up to 60 bar for the first time. The popular UNIFAC‐Lei model was successfully extended to long‐chain imidazolium‐based IL and gas (CO₂, CO, and H₂) systems. The free volume theory was used to explain the gas solubility and selectivity in imidazolium‐based ILs by calculating the fractional free volume and free volume by the COSMO‐RS model. Furthermore, the excess enthalpy of gas‐IL system was concerned to provide new insights into temperature dependency of gas (CO₂, CO, and H₂) solubility in ILs. The experimental data, calculation, and theoretical analysis presented in this work are important in gas separations with ILs or supported ionic liquid membranes. © 2017 American Institute of Chemical Engineers AIChE J, 63: 1792–1798, 2017     

1‐Allyl‐3‐methylimidazolium halometallate ionic liquids as efficient catalysts for the glycolysis of poly(ethylene terephthalate)

Series of 1‐allyl‐3‐methylimidazolium halometallate ionic liquids (ILs) were synthesized and used to degrade poly(ethylene terephthalate) (PET) as catalysts in the solvent of ethylene glycol. One important feature of these new IL catalysts is that most of them, especially [amim][CoCl₃] and [amim][ZnCl₃], exhibit higher catalytic activity under mild reaction condition, compared to the traditional catalysts [e.g., Zn(Ac)₂], the conventional IL catalysts (e.g., [bmim]Cl), Fe‐containing magnetic IL catalysts (e.g., [bmim][FeCl₄]), and metallic acetate IL catalysts (e.g., [Deim][Zn(OAc)₃]). For example, using [amim][ZnCl₃] as catalyst, the conversion of PET and the selectivity of bis(hydroxyethyl) terephthalate (BHET) reach up to 100% and 80.1%, respectively, under atmospheric pressure at 175°C for only 1.25 h. Another important feature is that BHET can be easily separated from the catalyst and has a high purity. Finally, based on the experimental phenomena, in ‐situ infrared spectra, and experimental results, the possible mechanism of degradation with synthesized IL is proposed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Metal‐ion‐containing ionic liquid hydrogels and their application to hydrogen production

A cationic hydrogel synthesized from (3‐acrylamidopropyl) trimethyl ammonium chloride as poly[(3‐acrylamidopropyl) trimethyl ammonium chloride] [p(APTMACl)] was put into contact with the chloride salts of metals such as CoCl₂, NiCl₂, and CuCl₂ in ethanol. The metal‐loaded p(APTMACl) hydrogels were used as catalyst systems in hydrogen generation from the hydrolysis of sodium borohydride (NaBH₄) and ammonia borane. The activation energy values for the hydrolysis reaction were calculated for all of the catalyst systems and were found to be 53.43 and 26.74 kJ/mol for p(APTMACl)–[CoCl₄]^2? and p(APTMACl)–[NiCl₄]^2?, respectively. These activation parameters were better than values reported in the literature for the ionic liquid metal complexes of smaller molecules used for the same purpose. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40183.     

Conducting epoxy networks modified with non‐covalently functionalized multi‐walled carbon nanotube with imidazolium‐based ionic liquid

Multi‐walled carbon nanotube (MWCNT) was non‐covalently functionalized with room‐temperature ionic liquid (IL), 1‐butyl‐3‐methyl‐imidazolium tetrafluoroborate and blended with epoxy pre‐polymer (ER) with the assistance of ultrasonication in the presence of acetone as a diluting medium. The ability of IL in improving the dispersion of MWCNT in epoxy pre‐polymer was evidenced by transmission optical microscopy. The corresponding epoxy/MWCNT networks cured with anhydride displayed an increase of the electrical conductivity of around three orders of magnitude with the addition of IL in a proportion of MWCNT/IL = 1:5 mass ratio. The effect of IL on dynamic mechanical properties and thermal conductivity was also evaluated. The improved thermal and electrical properties was attributed to the better dispersion of MWCNT within the epoxy matrix by IL, evidenced by transmission electron microscopy of the ER/MWCNT networks cured with anhydride. Raman spectroscopy was also used to confirm the interaction between MWCNT and IL. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43976.     

A molecular design method based on the COSMO‐SAC model for solvent selection in ionic liquid extractive distillation

In this study, a molecular design method was used to select solvents for extractive distillation. A COSMO‐SAC model was used to screen for prospective solvents from a wide variety of ionic liquids for extractive distillation. Based on the COSMO‐SAC model, the σ‐profile database of ILs was established. Selectivity and solubility were used as the indexes for solvent screening. According to the molecular design method, three suitable extractive distillation solvents were determined for acetonitrile‐water and ethanol‐cyclohexane systems. Vapor ‐ liquid equilibrium experiment were used to test chosen ILs. This study showed that the experimental and design results were consistent with each other. Therefore, this method is effective and applicable to pick ILs solvents for extractive distillation, and the results could provide a theoretical foundation for industrial production. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2853–2869, 2016     

Lipase‐catalyzed acylation of konjac glucomannan in ionic liquids

A comparative study was made of lipase‐catalyzed acylation of konjac glucomannan (KGM) with vinyl acetate as the acyl donor in five ionic liquids (ILs) and also in the presence of the organic solvent tert‐butanol (t‐BuOH). An obvious enhancement in enzyme activity and stability was observed using ILs as the reaction media when compared with t‐BuOH. The maximum degree of substitution (DS) of the modified KGM in ILs and t‐BuOH under the conditions employed is 0.71 and 0.54, respectively. The water activity (a_w) of the reaction system affected the acylation of KGM to some extent. 1‐Butyl‐3‐methylimidazolium tetrafluoroborate (C₄MIm.BF₄) was the best IL medium for the reaction, and an a_w of 0.75 was optimum. It was also found that the nature of both the cation and the anion of ILs had an effect on the reaction. Candida antarctica lipase B immobilized on an acrylic resin (Novozym 435) displayed no acylation activity to KGM in 1‐butyl‐3‐methylimidazolium chloride (C₄MIm.Cl). The optimum reaction temperature for enzymatic acylation in ILs was shown to be 45‐55 °C. Enzymatic acylation of KGM in IL‐t‐BuOH co‐solvent systems was also investigated. When an appropriate amount of t‐BuOH was added to ILs, the DS of the modified KGM was enhanced. Additionally, the enzymatic acylation of KGM in all the media examined was shown to be regioselective, with acylation occurring predominantly at the C‐6‐OH. Copyright © 2006 Society of Chemical Industry