Experimental investigation of the influence of the compounding process and the composite composition on the mechanical properties of a short flax fiber–reinforced polypropylene composite

Polypropylene (PP) composites containing 20 wt% short flax fibers are prepared, and the process parameters such as throughput, rotational speed, and screw configuration are varied during melt compounding with a corotating intermeshing twin‐screw extruder. The investigations reveal that low rotational speeds, high throughputs, and moderate shear energy inputs by the screw configuration led to an optimum set of mechanical properties. To investigate the influence of different composite compositions on the mechanical properties, composites with fiber contents between 0 and 40 wt% and maleic anhydride‐grafted PP (PP‐g‐MA) contents between 0 and 7 wt% are prepared. Increasing fiber contents enhance the Young's modulus and decrease the elongation at break and the notched impact strength. The tensile strength is barely affected. The addition of PP‐g‐MA increases the tensile strength as well as the elongation at break, whereas the Young's modulus is not influenced. Thus, PP‐g‐MA enhances the adhesion between PP and flax fibers significantly. POLYM. COMPOS., 36:2282–2290, 2015. © 2014 Society of Plastics Engineers     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fatigue life of coir fiber reinforced PP composites: Effect of compatibilizer and coir fiber contents

The fatigue behavior of polypropylene/coir fiber composites was investigated. Composites were prepared according to an experimental statistical design, in which the independent variables coir fiber and compatibilizer content were varied. The compatibilizer used was maleic anhydride grafted polypropylene (PP‐g‐MA). Compatibilizer free composites were also prepared. Composites were prepared in a corotating twin‐screw extruder and the mechanical behavior of polypropylene/coir fiber composites were assessed through monotonic (tensile) and cyclic (fatigue) tests. Fatigue load controlled tests were conducted under tension–tension loads at a frequency of 6 Hz. The fracture mechanism was accompanied by surface fracture analyses using scanning electron microscopy (SEM). The results indicated the need for using compatibilizer in the composites; however, increase in compatibilizer content did not affect composite fatigue lifetime. Coir content was the variable with the strongest effect on composite properties; increasing this variable caused significant increase in fatigue life. POLYM. ENG. SCI., 53:2159–2165, 2013. © 2013 Society of Plastics Engineers     

Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Process–structure–property relationship in ternary short‐glass‐fiber/elastomer/polypropylene composites

Short‐glass‐fiber (SGF)‐reinforced polypropylene (PP) composites toughened with a styrene/ethylene butylene/styrene (SEBS) triblock copolymer were injection molded after extrusion. Furthermore, a maleic anhydride (MA)‐grafted SEBS copolymer (SEBS‐g‐MA) was used as an impact modifier and compatibilizer. The effects of the processing conditions and compatibilizer on the microstructure and tensile and impact performance of the hybrid composites were investigated. In the route 1 fabrication process, SGF, PP, and SEBS were blended in an extruder twice, and this was followed by injection molding. In route 2, or the sequential blending process, the elastomer and PP were mixed thoroughly before the addition of SGF. In other words, either PP and SEBS or PP and SEBS‐g‐MA pellets were premixed in an extruder. The produced pellets were then blended with SGF in the extruder, and this was followed by injection molding. The SGF/SEBS‐g‐MA/PP hybrid fabricated by the route 2 process exhibited the highest modulus, yield stress, tensile stress at break, Izod impact energy, and Charpy drop weight impact strength among the composites investigated. This was due to the formation of a homogeneous SEBS elastomeric interlayer at the SGF and matrix interface of the SGF/SEBS‐g‐MA/PP hybrid. This SEBS rubbery layer enhanced the interfacial bonding between SGF and the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The correlations between the processing, microstructure, and properties of the hybrids were investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1384–1392, 2003     

Polypropylene composites reinforced with untreated and chemically treated coir: Effect of the presence of compatibilizer

The effect of coir surface modification on the compatibility of polypropylene (PP)/coir fiber (CF) composites, in the presence and absence of compatibilizer (maleic anhydride grafted polypropylene, PP‐g‐MA) was assessed. Chemical pulping of the fibers was performed with 2, 4, 8, and 12% NaOH solutions for a period of 2 h at (100 ± 4)°C. Pressed composite samples were subjected to tensile testing, scanning electron (SEM) and atomic force microscopy (AFM). Lignin and holocellulose concentrations of untreated and treated coir were determined. Pulping resulted in increased tensile strength of the composites containing coir treated with up to 2% NaOH, due to increased fiber roughness as evidenced by AFM. This property decreased when higher NaOH concentrations were used, likely due to increased deterioration of coir. The presence of compatibilizer in the PP composites containing treated coir altered adhesion due to chemical changes of the fiber surface. At high NaOH concentrations increased delignification and therefore increased exposure of hydroxyls favors reaction between the fiber hydroxyls and the carboxyl acids of the hydrolyzed maleic anhydride, present in the composites. POLYM. ENG. SCI., 55:2050–2057, 2015. © 2014 Society of Plastics Engineers     

Development and characterization of green composites from bio‐based polyethylene and peanut shell

In the present work, different compatibilizers, namely polyethylene‐graft‐maleic anhydride (PE‐g‐MA), polypropylene‐graft‐maleic anhydride (PP‐g‐MA), and polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene‐graft‐maleic anhydride (SEBS‐g‐MA) were used on green composites derived from biobased polyethylene and peanut shell (PNS) flour to improve particle–polymer interaction. Composites of high‐density polyethylene/peanut shell powder (HDPE/PNS) with 10 wt % PNS flour were compatibilized with 3 wt % of the abovementioned compatibilizers. As per the results, PP‐g‐MA copolymer lead to best optimized properties as evidenced by mechanical characterization. In addition, best particle–matrix interface interactions with PP‐g‐MA were observed by scanning electron microscopy (SEM). Subsequently HDPE/PNS composites with varying PNS flour content in the 5–30 wt % range with PP‐g‐MA compatibilizer were obtained by melt extrusion and compounding followed by injection molding and were characterized by mechanical, thermal, and morphological techniques. The results showed that PNS powder, leads to an increase in mechanical resistant properties (mainly, flexural modulus, and strength) while a decrease in mechanical ductile properties, that is, elongation at break and impact absorbed energy is observed with increasing PNS flour content. Furthermore, PNS flour provides an increase in thermal stability due to the natural antioxidant properties of PNS. In particular, composites containing 30 wt % PNS powder present a flexural strength 24% and a flexural modulus 72% higher than the unfilled polyethylene and the thermo‐oxidative onset degradation temperature is increased from 232 °C up to 254 °C thus indicating a marked thermal stabilization effect. Resultant composites can show a great deal of potential as base materials for wood plastic composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43940.     

Study of effect of old corrugated cardboard in properties of polypropylene composites: Study of mechanical properties,thermal behavior,and morphological properties

The investigation of the economical use of lignocellulose waste, which is one of the environmental problems facing nations, is ongoing. In this study, waste cardboard paper fiber reinforcing polypropylene (PP) composites was developed. In order to modify the PP matrix maleated PP (MA‐g‐PP) a 5 wt% and a grafting rate of 1 and 2 wt% was used as a compatibilizer. The effects of fiber and compatibilizer content as well as graft content are evaluated by mechanical, thermal property measurements, and scanning electron microscopy (SEM). The compatibilizer improved all mechanical properties significantly. Thus, the tensile strength of MA‐g‐PP‐containing composites increases compared to PP/cardboard composites paper content increases. However, the tensile modulus of a PP‐based composite increases with an increase in paper fiber with the compatibilizer having little effect. SEM revealed that the addition of MA‐g‐PP generates strong interactions between a PP matrix and paper fibers. However, the addition of the MA‐g‐PP compatibilizing agent gives a significant improvement on the crystallization of the composites, whereas the compatibilized PP/old corrugated cardboard (OCC) composites have higher crystallinity (Xc) than uncompatibilized PP/OCC composites. The MA‐g‐PP also diminished the water absorption in the composites. J. VINYL ADDIT. TECHNOL., 22:231–238, 2016. © 2014 Society of Plastics Engineers     

An investigation on the mechanical and dynamic rheological properties of single and hybrid filler/polypropylene composites based on talc and calcium carbonate

Some results of experiments on the mechanical and rheological properties of mineral filled polypropylene were presented. Single filler and hybrid filler composites of talc and calcium carbonate (CaCO₃) were prepared in a co‐rotating twin‐screw extruder. The effect of filler type, filler content, and coupling agent on the mechanical and rheological properties of the polypropylene were studied. The coupling agent was maleic anhydride‐grafted polypropylene (PP‐g‐MA). It was found that the mechanical properties are affected by filler type, filler concentration, and the interaction between filler and matrix. The tensile strength of the composite is more affected by the talc while the impact strength is influenced mostly by CaCO₃ content. The elongation at break of PP/CaCO₃ composites was higher than that of PP/talc composites. The incorporation of coupling agent into PP/mineral filler composites increased the mechanical properties. Rheological properties indicated that the complex viscosity and storage modulus of talc filled samples were higher than those of calcium carbonate filled samples while the tan δ was lower. The rheological properties of hybrid‐filler filled sample were more affected by the talc than calcium carbonate. The PP‐g‐MA increased the complex viscosity and storage modulus of both single and hybrid composites. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Mechanical and thermal flow properties of wood flour–biodegradable polymer composites

Wood flour (WF)–polycaprolactone (PCL) and polybutylenesuccinate–butylenecarbonate (PBSC) composites were prepared by knead processing. The effects of a compatibilizer on the tensile and thermal flow properties of the composites were investigated. PCL‐graft‐maleic anhydride (PCL‐g‐MA) was used as a compatibilizer. Tensile properties were improved by adding PCL‐g‐MA to both composites. The tensile strength and Young's modulus were increased from 13 to 27 MPa and 581 to 1011 MPa in WF–PCL (50/50, w/w) composites, respectively, and from 17 to 28 MPa and 814 to 1007 Mpa in WF–PBSC (50/50, w/w) composites, respectively, with the addition of 5% PCL‐g‐MA. Elongation at break increased from 4 to 7% and from 3 to 6% in the WF–PCL and the WF–PBSC composites, respectively. Tensile strength was further increased with increasing WF content in the presence of PCL‐g‐MA. Thermal flow temperature and melt viscosity of the composites were increased, and water absorption and thickness swelling were improved with the addition of PCL‐g‐MA. It was found from the burial test that all composites were more than 40% degraded within 6 weeks, and there was no considerable difference in degradation between composites with PCL‐g‐MA and those without. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1900–1905, 2003     

Silica‐filled polypropylene composites: The effect of ethylene diamine dilaurate and maleic anhydride grafted polypropylene on mechanical properties,water absorption,morphology, and thermal properties

The effect of two compatibilizers, i.e. ethylene diamine dilaurate (EDD) and maleic anhydride grafted polypropylene (MAPP) on the mechanical properties, water absorption, morphology, and thermal properties of silica‐filled polypropylene (PP/Sil) composites were studied. The results show that the tensile, impact and flexural strengths (up to 2 php), Young's modulus, and elongation at break (Eb) increased with increasing EDD content. However, increasing MAPP content increases the tensile strength, Young's modulus, impact and flexural strengths, and water absorption resistance. At a similar compatibilizer content, EDD exhibits higher Eb, impact and flexural strengths but lowers tensile strength, Young's modulus, and water absorption resistance compared with MAPP. Scanning electron microscopy study of tensile fractured surfaces exhibits the evidence of better silica‐PP adhesion with MAPP and EDD compared with the similar composites but without compatibilizer. Fourier transform infra red spectra provide an evidence of interaction between EDD or MAPP with PP/Sil composites. Termogravimetry analysis results indicate that the addition of EDD or MAPP slightly increases the thermal stability of PP/Sil composites. Differential scanning calorimetry also indicates that PP/Sil composites with EDD or MAPP have higher heat fusion (ΔH_f(com)) and crystallinity (X_com) than similar composites but without compatibilizer. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Mechanical properties of injection molded long fiber polypropylene composites,Part 1: Tensile and flexural properties

Innovative polymers and composites are broadening the range of applications and commercial production of thermoplastics. Long fiber‐reinforced thermoplastics have received much attention due to their processability by conventional technologies. This study describes the development of long fiber reinforced polypropylene (LFPP) composites and the effect of fiber length and compatibilizer content on their mechanical properties. LFPP pellets of different sizes were prepared by extrusion process using a specially designed radial impregnation die and these pellets were injection molded to develop LFPP composites. Maleic‐anhydride grafted polypropylene (MA‐g‐PP) was chosen as a compatibilizer and its content was optimized by determining the interfacial properties through fiber pullout test. Critical fiber length was calculated using interfacial shear strength. Fiber length distributions were analyzed using profile projector and image analyzer software system. Fiber aspect ratio of more than 100 was achieved after injection molding. The results of the tensile and flexural properties of injection molded long glass fiber reinforced polypropylene with a glass fiber volume fraction of 0.18 are presented. It was found that the differences in pellet sizes improve the mechanical properties by 3–8%. Efforts are made to theoretically predict the tensile strength and modulus using the Kelly‐Tyson and Halpin‐Tsai model, respectively. POLYM. COMPOS., 28:259–266, 2007. © 2007 Society of Plastic Engineers     

An investigation on recycled PET/PP and recycled PET/PP‐EP compatibilized blends: Rheological,morphological, and mechanical properties

The effectiveness of P(E‐co‐MA‐co‐GMA) as a compatibilizer for recycled PET/PP and recycled PET/PP‐EP (polypropylene (ethylene‐propylene) heterophase copolymer) blends was investigated by means of morphological (scanning electron microscopy), rheological (small amplitude oscillatory shear), mechanical (tensile, flexural and impact tests), and thermal (differential scanning calorimetry) properties. Compatibilizer concentration ranged from 1 to 5 wt % with respect to the whole blend. All blends were obtained in a 90/10 composition using a twin screw extruder. Compatibilization effects for PETr/PP‐EP were more pronounced due to ethylene segments present in both PP‐EP and P(E‐co‐EA‐co‐GMA). PETr/PP‐EP has shown greater dispersed phase size reduction, a more solid‐like complex viscosity behavior and larger storage modulus at low frequencies in relation to PETr/PP blend. For both investigated blends, mechanical properties indicated an improvement in both elongation at break and impact strength with increasing compatibilizer content. PETr/PP‐EP blends showed improved performance for the same level of compatibilizer content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41892.     

Enhancement of PVC/ENR blend properties by poly(methyl acrylate) grafted oil palm empty fruit bunch fiber

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150°C, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Young's modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Young's modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the impact strength, UTS, and elongation at break of the composites were found to decrease with the increase in fiber loading. An increase in elongation at break and UTS and decrease in the flexural and Young's modulus was observed with the addition of PMA‐g‐OPEFB fiber compared to ungrafted fiber. This observation indicates that grafting of PMA onto OPEFB impart some flexibility to the blend. The morphology of cryogenically fractured and tensile fracture surfaces of the composites, examined by a scanning electron microscope shows that the adhesion between the fiber and the matrix is improved upon grafting of the OPEFB fiber. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of molecular weight and grafted maleic anhydride of functionalized polylactic acid used in reactive compatibilized binary and ternary blends of polylactic acid and thermoplastic cassava starch

Polylactic acid (PLA) was reactively functionalized with maleic anhydride (MA) and 2,5‐bis(tert‐butylperoxy)?2,5‐dimethylhexane (Luperox 101 or L101) using a twin screw extruder (TSE). The effects of functionality (grafted MA level) and/or number average molecular weight of functionalized PLA (PLA‐g‐MA) as the reactive polymer pairs (binary blends) and reactive compatibilizer (ternary blends) were investigated. Due to the dominant side reaction during melt free radical grafting, polymer degradation or chain scission, PLA‐g‐MA having a higher grafted MA had lower molecular weights and intrinsic viscosity as well as broader molecular weight distribution values. The thermal, physical, mechanical, and morphological properties of binary blends produced by using the TSE and injection molding at a ratio of 70 wt % PLA‐g‐MA and 30 wt % thermoplastic cassava starch (TPCS) were analyzed. The reactive blends having grafted MA more than 0.4 wt % had poor tensile strength and elongation at break. Similar trends in morphology and tensile properties were observed in the reactive ternary blends. The use of PLA‐g‐MA strongly impacted the elongation at break but not the modulus or tensile strength. An increase of PLA‐g‐MA's number average molecular weight ( or M_n) improved the tensile properties of the blends. The reactive ternary blend having 0.1 wt % grafted MA on PLA and PLA‐g‐MA basis and PLA‐g‐MA's M_n of 45 kDa offered the highest elongation at break. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42230.     

Rice straw fiber reinforced high density polyethylene composite: Effect of coupled compatibilizating and toughening treatment

In this study, rice‐straw (RS) filled high density polyethylene (HDPE) composites were manufactured by extrusion and injection molding. Three compatibilizers, which are unfunctionalized ethylene/propylene copolymer (uEPR), maleic anhydride grafted EPR (EPR‐g‐MA) and PE‐g‐MA, and their combinations were introduced to strengthen fiber‐matrix interphase. The mechanical and morphological properties of composites were investigated. For single‐compatibilizer system, PE‐g‐MA or EPR‐g‐MA alone enhanced tensile, flexural, and impact strengths of resultant composites compared with HDPE/RS system without compatibilizers. Different toughening origins of individual compatibilizer were discussed based on composites' interphase morphologies and mechanical properties. For combined‐compatibilizers system, the PE‐g‐MA/EPR weight ratio is important for several properties of composites. The optimum ratio was considered as 2 : 1 and 1 : 1 for PE‐g‐MA/uEPR and PE‐g‐MA/EPR‐g‐MA modified composites, respectively. Also, composites modified by combined PE‐g‐MA/EPR‐g‐MA showed better impact strength than that modified by PE‐g‐MA alone. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Linear low‐density polyethylene/(soya powder) blends containing polyethylene‐g‐(maleic anhydride) as a compatibilizer

Blends were made from linear low‐density polyethylene (LLDPE) and various amounts of soya powder. The soya powder content was varied from 5 to 20 wt%. Polyethylene‐g‐(maleic anhydride) (PE‐g‐MA) was used as a compatibilizer. Tensile strength and elongation at break (EB) decreased with increasing soya powder content. However, Young's modulus increased with the incorporation of soya powder. The addition of PE‐g‐MA as a compatibilizer increased the tensile strength, EB, and modulus of the blends. The interfacial adhesion between soya powder and LLDPE was improved by the incorporation of PE‐g‐MA, as demonstrated by scanning electron microscopy. Increasing the content of soya powder reduced the crystallinity of the LLDPE phase. The addition of PE‐g‐MA had no significant effect on melting temperature, but the degree of crystallinity of the LLDPE was increased. The thermal stability of the blends was determined by using thermogravimetric analysis. Thermal stability decreased with increasing soya powder loading. However, the addition of PE‐g‐MA slightly increased the thermal stability of LLDPE/(soya powder) blends. J. VINYL ADDIT. TECHNOL., 2009. © 2009 Society of Plastics Engineers     

Bamboo fiber reinforced polypropylene composites and their mechanical,thermal, and morphological properties

Short bamboo fiber reinforced polypropylene composites were prepared by incorporation of various loadings of chemically modified bamboo fibers. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as compatibilizer to improve fiber–matrix adhesion. The effects of bamboo fiber loading and modification of the resin on the physical, mechanical, thermal, and morphological properties of the bamboo reinforced modified PP composites were studied. Scanning electron microscopy studies of the composites were carried out on the interface and fractured surfaces. Thermogravimetric analysis and IR spectroscopy were also carried out. At 50% volume fraction of the extracted bamboo fiber in the composites, considerable increase in mechanical properties like impact, flexural, tensile, and thermal behavior like heat deflection temperature were observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of compatibilizers on the physico‐mechanical and foaming properties of polyproylene/wood‐fiber composites

Polypropylene (PP)/wood‐fiber (WF) composites were prepared by intermeshing co‐rotating twin screw extruder, and microcellular closed cell PP/WF composite foams were prepared by using pressure‐quenched batch process method. The effect of various compatibilizers on the mechanical properties, morphology, crystallinity, rheological properties, and foamability of PP/WF composites were investigated. The results showed that PP/WF composite with addition of PP‐g‐MA as compatibilizer had the highest tensile strength, stiffness, and crystallinity, after foaming, it showed highest relative density and cell density, as well as the smallest cell size. Higher crystallinity of PP/WF composites, showed higher stiffness and higher relative density. J. VINYL ADDIT. TECHNOL., 19:250–257, 2013. © 2013 Society of Plastics Engineers     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers