Thermodynamic incompatibility between denatured whey protein and konjac glucomannan

The current study investigated the effect of a neutral polysaccharide, konjac glucomannan, on the heat-induced gelation of whey protein isolate (WPI) at pH 7. Oscillatory rheology (1 rad/s; 0.5% strain), differential scanning calorimetry and confocal laser scanning microscopy were used to investigate the effect of addition of konjac in the range 0-0.5% w/w, on the thermal gelation properties of WPI. The minimum gelling concentration for WPI samples was 11% w/w; the concentration was therefore held constant at this value. Gelation of WPI was induced by heating the samples from 20 to 80 °C, holding at 80 °C for 30 min, cooling to 20 °C, and holding at 20 °C for a further 30 min. On incorporation of increasing concentrations of konjac the gelation time decreased, while the storage modulus (G′) of the mixed gel systems increased to ∼1450 Pa for 11% w/w WPI containing 0.5% w/w konjac gels, compared to 15 Pa for 11% w/w WPI gels (no konjac). This increase in gel strength was attributed to segregative interactions between denatured whey proteins and konjac glucomannan.     

Rheological properties of rennet casein-whey protein gels prepared at different mixing speeds

The rheological properties at small (oscillatory shear) and large (uniaxial compression) deformations of heat-induced gels (80 °C for 20 min, pH 7.3) containing 25% rennet casein (RCN), 2.5% disodium phosphate and 0%, 2.3% or 6.3% of whey protein isolate (WPI) were measured for samples cooked in a torque-rheometer at mixing speeds within a range of 20–200 rpm (shear rates: ∼15–230 s⁻¹). In addition, microstructure analyses were performed, separately staining RCN and WPI, by Confocal Scanning Laser Microscopy (CSLM). Both small and large deformation tests indicated that increasing addition of WPI prior to the cooking process of RCN resulted in gels exhibiting higher storage and deformability moduli than WPI-free samples. Increasing shear rates during cooking also affected the rheological properties of RCN–WPI gels, and stronger gels were formed as the shear rate during cooking was increased. Despite the data dispersion among replicates, the effect of shear rate on gel strength were evident for RCN gels with 6.3% WPI and relatively clear for gels with 2.3% WPI; however, the trend was uncertain for WPI-free RCN gels. Possible explanations for this observation are that when increasing WPI levels in the presence of RCN and heat, disulfide-thiol exchange reactions between denatured WPI and κ-casein (κ-CN) are increased and possibly promoted by shear rate, resulting in stronger and more cross-linked gel structure. CSLM results were not conclusive to support this hypothesis.     

Enhanced functionalities of whey proteins treated with supercritical carbon dioxide

The functionality of whey proteins can be modified by many approaches; for example, via complexation with carbohydrates, enzymatic cross-linking, or hydrolysis, and the objective of this work was to research the effects of supercritical carbon dioxide (scCO₂) treatments on the functionalities of commercial whey protein products including whey protein isolates (WPI) and whey protein concentrates (WPC). The WPI and WPC powders and a 10% (wt/vol) WPI solution were treated with scCO₂. The WPI solution was treated at 40°C and 10 MPa for 1 h, whereas WPI and WPC powders were treated with scCO₂ at 65°C and 10 or 30 MPa for 1 h. Dynamic rheological tests were used to characterize gelation properties before and after processing. Compared with the unprocessed samples and samples processed with N₂ under similar conditions, scCO₂-treated WPI, whether dispersed in water or in the powder form during treatments, formed a gel with increased strength. The improvement in gelling properties was more significant for the scCO₂-treated WPC. In addition, the scCO₂-processed WPI and WPC powders appeared to be fine and free-flowing, in contrast to the clumps in the unprocessed samples. Proximate compositional and surface hydrophobicity analyses indicated that both compositional and structural changes may have contributed to enhanced whey protein functionalities. The results suggest that functionalities of whey proteins can be improved by scCO₂ treatment to produce novel ingredients.     

Effects of protein concentration and oil-phase volume fraction on the stability and rheology of menhaden oil-in-water emulsions stabilized by whey protein isolate with xanthan gum

The influences of protein concentration (0.2, 1, 2 wt%) and oil-phase volume fraction (5%, 20%, 40% v/v) on emulsion stability and rheological properties were investigated in whey protein isolate (WPI)-stabilized oil-in-water emulsions containing 0.2 wt% xanthan gum (XG). The data of droplet size, surface charge, creaming index, oxidative stability, and emulsion rheology were obtained. The results showed that increasing WPI concentration significantly affected droplet size, surface charge, and oxidative stability, but had little effect on creaming stability and emulsion rheology. At 0.2 wt% WPI, increasing oil-phase volume fraction greatly increased droplet size but no significant effect on surface charge. At 1 or 2 wt% WPI, increasing oil-phase volume fraction had less influence on droplet size but led to surface charge more negative. Increasing oil-phase volume fraction facilitated the inhibition of lipid oxidation. Meanwhile, oil-phase volume fraction played a dominant role in creaming stability and emulsion viscosity. The rheological data indicated the emulsions may undergo a behavior transition from an entropic polymer gel to an enthalpic particle gel when oil-phase volume fraction increased from 20% to 40% v/v.     

Influence of shearing on the physical characteristics and rheological behaviour of an aqueous whey protein isolate–κappa-carrageenan mixture

The incompatibility of whey protein isolate (WPI) and κappa-carrageenan (κ-car) in aqueous mixtures has been extensively studied under quiescent conditions; however, the effect of shear on segregative phase separation is still not fully understood. The present work reports for the first time quantitatively the effect of shearing on the segregative phase separation behaviour of these two polymers. Demixing was observed at pH 7.0 and 22 °C, determining the phase diagram and rheological properties of the mixtures. Phase diagrams were derived after heating and cooling mixes at a constant shear rate (28 s⁻¹). The phase behaviour was compared to that of the same mixtures under quiescent conditions. The shearing process affects segregative phase separation, causing a shift in the position of the binodal towards lower concentrations of WPI. The bottom layer contained a higher ratio of WPI while the upper layer was enriched in κ-car. The addition of κ-car to WPI solutions led to a much stiffer heat-induced gel than that prepared with WPI heated in isolation. The height of the plateau of the final elastic modulus G′_∞(t) depends on the position of the system on the phase diagram. Using a selected tie line, the viscosity of different systems measured at 80 °C was more influenced by the amount of WPI, than by the κ-car concentration. Shear treatment of segregative phase separating systems offer a way to modulate the functional properties of the ingredients and the texture of the final product.     

Effect of trisodium citrate on rheological and physical properties and microstructure of yogurt

The effect of trisodium citrate (TSC) on the rheological and physical properties and microstructure of yogurt was investigated. Reconstituted skim milk was heated at 85° C for 30 min, and various concentrations (5 to 40 mM) of TSC were added to the milk, which was then readjusted to pH 6.50. Milk was inoculated with 2% yogurt culture and incubated at 42° C until pH was 4.6. Acid-base titration was used to determine changes in the state of colloidal calcium phosphate (CCP) in milk. Total and soluble Ca contents of the milk were determined. The storage modulus (G′) and loss tangent (LT) values of yogurts were measured as a function of pH using dynamic oscillatory rheology. Large deformation rheological properties were also measured. Microstructure of yogurt was observed using confocal scanning laser microscopy, and whey separation was also determined. Addition of TSC reduced casein-bound Ca and increased the solubilization of CCP. The G′ value of gels significantly increased with addition of low levels of TSC, and highest G′ values were observed in samples with 10 to 20 mM TSC; higher ( > 20 mM) TSC concentrations resulted in a large decrease in G′ values. The LT of yogurts increased after gelation to attain a maximum at pH ∼5.1, but no maximum was observed in yogurts made with ≥ 25 mM of TSC because CCP was completely dissolved prior to gelation. Partial removal of CCP resulted in an increase in the LT value at pH 5.1. At low TSC levels, the removal of CCP crosslinks may have facilitated greater rearrangement and molecular mobility of the micelle structure, which may have helped to increase G′ and LT values of gels by increasing the formation of crosslinks between strands. At high TSC concentrations the micelles were completely disrupted and CCP crosslinks were dissolved, both of which resulted in very weak yogurt gels with large pores obvious in confocal micrographs. Gelation pH and yield stress significantly decreased with the use of high TSC levels. Lowest whey separation levels were observed in yogurt made with 20 mM TSC, and whey separation greatly increased at > 25 mM TSC. In conclusion, low concentrations of TSC improved several important yogurt characteristics, whereas the use of levels that disrupted casein micelles resulted in poor gel properties. We also conclude that the LT maximum observed in yogurts made from heated milk is due to the presence of CCP because the modification of the CCP content altered this peak and the removal of CCP eliminates this feature in the LT profiles.     

Casein glycomacropeptide pH-driven self-assembly and gelation upon heating

Casein glycomacropeptide (CMP) found in cheese whey is a C-terminal hydrophilic glycopeptide released from κ-casein by the action of chymosin during cheese making. In a previous work a self-assembly model for CMP at room temperature was proposed, involving a first step of hydrophobic assembly followed by a second step of electrostatic interactions which occurs below pH 4.5. The objective of the present work was to study, by dynamic light scattering (DLS), the effect of heating (35–85 °C) on the pH-driven CMP self-assembly and its impact on the dynamics of CMP gelation. The concentration of CMP was 3% w/w for DLS and 12% w/w for rheological measurements. The solutions at pH 4.5 and 6.5 did not show any change in the particle size distributions upon heating. In contrast the solutions at pH lower than 4.5 that showed electrostatic self-assembly at room temperature were affected by heating. The mean diameter of assembled CMP increased by decreasing pH. For all solutions with pH lower than 4.5, the particle size did not change on cooling, suggesting that the assembled CMP forms formed during heating were stable. The gel point determined as G′–G″ crossover, occurred in all systems at 70 °C, but at different times. The rate of self-assembly determined by DLS as well as the rate of gelation increased with increasing temperature and decreasing pH from 4 to 2. Increasing temperature and decreasing pH, the first step of CMP self-assembly by hydrophobic interactions is speed out. All the self-assembled structures and the gels formed at different temperatures were pH-reversible but did not revert to the initial size (monomer) but to associated forms that correspond mainly to CMP dimers.     

湿热条件下低聚木糖-乳清分离蛋白的美拉德反应及产物乳化性与流变性研究

本文研究了湿热条件下不同混合质量比(1:1、1:2、1:3、1:4,W/W)对低聚木糖与乳清分离蛋白(WPI)美拉德反应及其产物的乳化性与流变性的影响。UV-Vis吸光度值,pH和粒径大小显著变化表明,该条件下成功制备了WPI和低聚木糖的美拉德反应产物 (MRPs)。数据显示,质量比为1:2的溶液体系美拉德反应程度最高;与未经过美拉德反应的体系相比,MRPs的平均粒径均减小而质量比为1:2的体系平均粒径最大;同时,美拉德反应提高了WPI的乳化活性和乳化稳定性,比例为1:2时MRPs具有最佳的乳化活性(38.63 m2/g)和乳化稳定性(65.23%);流变学测试表明糖基化修饰增强了WPI的凝胶性,比例为1:3时MRPs的储存模量提高最大,G''值高达约97,000 Pa (约WPI的7倍);在相同剪切速率下,MRPs溶液的表观粘度增加,而WPI的添加比例对体系粘度的影响占主导作用。上述研究表明,美拉德反应可改善WPI的乳化特性和凝胶特性。     

Improvement of canola protein gelation properties through enzymatic modification with transglutaminase

Enzymatic modification with transglutaminase (TG) was used to enhance the gelation of canola protein isolate (CPI) and thus improve its potential as a food ingredient. The effects of CPI concentration, TG concentration, treatment temperature and treatment time on CPI gelation properties were evaluated. A texture analyzer, sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) and scanning electron microscopy were used to characterize the resulting networks. The protein concentration, amount of TG, and treatment temperature were found to significantly impact gel strength. It was found that gelation can be improved by increasing the amounts of protein and TG and by keeping the treatment temperature close to 40 °C. SDS-PAGE showed that cross-linking of subunits occurred through TG treatment thus helping to explain the increase in gel strength observed during texture analysis. Micrographs further corroborated the trends noted during rheological studies.     

Short communication: The effect of dry period duration and dietary energy density in early lactation on the rennet gelation properties of milk

This study was carried out to examine the effects of decreasing the dry period (DP) duration and altering the energy density of the diet during early lactation on the rheological characteristics of milk. Forty mature Holstein-Friesian cows were used in a completely randomized design with a 2 × 2 factorial arrangement of treatments. Cows were randomly assigned to 1 of 2 dry period treatments and 1 of 2 nutritional treatments. The DP treatments were continuous milking (CM) or an 8-wk standard dry period (SDP), and the nutritional treatments were a standard energy diet (SE) or a high energy diet (HE). Actual DP lengths were 6.3 ± 1.7 d and 62.1 ± 1.9 d for cows on the CM and SDP treatments, respectively. Milk samples were collected at 2, 6, and 10 wk postpartum. The concentrations of fat, protein, and lactose were determined in each sample. The rennet gelation properties were measured at 31°C using dynamic low-amplitude strain oscillatory rheometry. The following parameters were obtained from the resultant elastic shear modulus (G′): gelation time, maximum curd firming rate, and gel strength. Reducing the DP duration from 62 to 6 d resulted in increases in milk protein concentration (31.8 vs. 34.7 g/kg), maximum curd firming rate (2.58 vs. 3.60 Pa/min), and gel strength (69.4 vs. 90.5 Pa). Increasing the dietary energy density decreased percentage milk fat (43.1 vs. 37.7 g/kg) but otherwise had no effect. Gel strength was correlated with maximum curd firming rate (r = 0.99), and both variables were correlated with milk protein concentration (r = 0.71 and r = 0.73, respectively). The results indicate that decreasing the duration of the DP increased milk protein concentration and improved the rennet gelation properties of milk, but that dietary energy density had little effect.     

Segregative interactions and competitive binding of Ca in gelling mixtures of whey protein isolate with Naκ-carrageenan

Gelling mixtures of Na⁺κ-carrageenan with whey protein isolate (WPI) at pH 7.0 have been studied rheologically and by differential scanning calorimetry (DSC), with comparative measurements for the individual constituents of the mixtures. The concentration of WPI was held fixed at 10.0 wt% and carrageenan concentration was varied in the range 0.05–3.0 wt%. Ca²⁺ cations, which have been shown previously to be particularly effective in inducing gelation of κ-carrageenan, were introduced as CaCl₂. The concentration of CaCl₂ used in most of the experiments was 8 mM, but other concentrations were also studied. Mixtures were prepared in the solution state at 45 °C, and showed no evidence of either phase separation or complex formation. Rheological changes were monitored by low-amplitude oscillatory measurements of storage modulus, G′, during (i) cooling (1 °C/min) and holding at 5 °C, to induce gelation of the carrageenan in the presence of non-gelled WPI; (ii) heating and holding at 80 °C to dissociate the carrageenan network and induce gelation of WPI; (iii) cooling and holding again at 5 °C, to give composite networks with both components gelled; and (iv) re-heating to 80 °C to dissociate the carrageenan network. Gel structure was characterised further by creep–recovery measurements at the end of each holding period, and by torsion measurements at 5 °C, before and after thermal gelation of WPI.     

Manufacture of acid gels from skim milk using high-pressure homogenization

The effect of high-pressure homogenization (HPH) alone or in combination with a thermal treatment (TT) was investigated for the manufacture of acid gels from skim milk. Raw skim milk was subjected to HPH (0 to 350 MPa) or a TT (90°C, 5 min), or both, in the following processing combinations: 1) HPH, 2) HPH followed by TT, 3) TT followed by HPH, 4) TT, and 5) raw milk (control). After treatments, L* (lightness) values were measured, and then skim milk was acidified with 3% glucono-δ-lactone and rheological properties (G′ and gelation time), and whey holding capacity was evaluated. Treatments in which HPH and TT were combined showed greater L* values than those in which just HPH was applied. In all treatments, the L* values decreased as the pressure was increased up to 300 MPa with little change afterward. Gelation times were lower when HPH was combined with TT compared with the acid skim milk gels that were just pressure treated. The final G′ in gels obtained from skim milk subjected to the combined process (HPH and TT) was greater and pressure-dependent compared with all other gels. A maximum G′ (∼320 Pa) was observed with skim milk subjected to a combination of thermal processing before or after HPH at 350 MPa. Acid gels obtained from HPH milk at 350 MPa showed a linear decrease in whey holding capacity over time, retaining 20% more whey after centrifugation for 25 min compared with samples treated at lower pressures and all other treatments. Our results suggest that HPH in combination with TT can be used to improve the rheological properties and stability of yogurt, thus decreasing the need for additives.     

Modification of rheological properties of whey protein isolates by limited proteolysis

Whey protein isolate (WPI) was subjected to limited tryptic hydrolysis and the effect of the limited hydrolysis on the rheological properties of WPI was examined and compared with those of untreated WPI. At 10% concentration (w/v in 50 mM TES buffer, pH 7.0, containing 50 mM NaCl), both WPI and the enzyme-treated WPI (EWPI) formed heat-induced viscoelastic gels. However, EWPI formed weaker gels (lower storage modulus) than WPI gels. Moreover, a lower gelation point (77 °C) was obtained for EWPI as compared with that of WPI which gelled at 80 °C only after holding 1.4 min. Thermal analysis and aggregation studies indicated that limited proteolysis resulted in changes in the denaturation and aggregation properties. As a consequenece, EWPI formed particulated gels, while WPI formed fine-stranded gels. In keeping with the formation of a particulate gel, Texture Profile Analysis (TPA) of the heat-induced gels (at 80 °C for 30 min) revealed that EWPI gels possessed significantly higher (p < 0.05) cohesiveness, hardness, gumminess, and chewiness but did not fracture at 75% deformation. The results suggest that the domain peptides, especially β-lactoglobulin domains released by the limited proteolysis, were responsible for the altered gelation properties.     

Improvement of microbial transglutaminase‐induced gelation of β‐conglycinin by conjugation with dextran

This work focused on the effect of glycosylation on the gelation ability of β‐conglycinin induced by microbial transglutaminase (MTGase). Rheological results indicated that the gels of β‐conglycinin‐dextran conjugate products exhibited higher G′ value (172.2 ± 8.6 Pa) compared with those of dry‐heated β‐conglycinin (75.2 ± 5.1 Pa), β‐conglycinin (53.3 ± 4.0 Pa) and β‐conglycinin‐dextran mixture (38.6 ± 2.6 Pa) after 4 h incubation with MTGase. The gels prepared from β‐conglycinin‐dextran conjugate products had higher hardness, fracturability, springiness and cohesiveness values determined by textural profile analysis. The turbidity of β‐conglycinin‐dextran conjugate products solution incubated with MTGase increased faster than those of the other three protein samples. The conjugated dextran in β‐conglycinin‐dextran conjugate products could inhibit extensive protein–protein interactions which might result in the formation of more ordered and stronger gel network structures during MTGase cross‐linking process. A compact and homogeneous gel networks in β‐conglycinin‐dextran conjugate products gels were also observed by scanning electron microscopy.     

Effects of fluid shear and temperature on whey protein gels, pure or mixed with xanthan

The effects of shear on whey protein isolate (WPI) gels, pure or mixed with xanthan, have been investigated at pH 5.4 by dynamic oscillatory measurements and light microscopy (LM). The shear was performed on the suspensions under a constant stress of between 0.04 and 2.1 Pa. Various temperature conditions were chosen in order to describe the effects of shear at the different states of aggregation of the WPI. Shear-sensitive aggregation phenomena were already found around 40°C for the pure WPI samples. Continuous shearing during heating from 20 to 40°C, prior to heat treatment at 90°C, resulted in a gel with a storage modulus (G′) half that of the unsheared gel, independent of the shear stress. Continuous shearing during heating from 20 to 76°C resulted in a further decrease in G′. Inhomogeneities arose in networks formed from continuously sheared suspensions during heating from 20 to 50°C and above. Depending on the shear stress and on the heating range of the shear, the networks showed areas of varied compactness and different classes of pores, ranging from 10 to 200 μm. A higher G′, compared to that for the unsheared gel, was found for gels subjected to shear for short periods in the vicinity of the gel point. The presence of xanthan inhibited the aggregation and demixing of the WPI, described as a sterical phenomenon. Under static conditions, the presence of xanthan resulted in a more homogeneous WPI network. Exposing the mixed suspensions to shear generally increased the inhomogeneity of the network structure. Short periods of shearing in the vicinity of the gel point affected the kinetics of the gel formation and resulted in gels with higher G′ values than the unsheared gel. Continuous shearing under stresses below 0.09 Pa, during heating from 20 to 60°C and above, also resulted in gels with an increased G′. Continuous shear under stresses above 0.9 Pa resulted in gels with a decreased G′     

Influence of muscle type on rheological properties of porcine myofibrillar protein during heat-induced gelation

The gelation characteristics of myofibrillar proteins are indicative of meat product texture. Defining the performance of myofibrillar proteins during gelation is beneficial in maintaining quality and developing processed meat products and processes. This study investigates the impact of pH on viscoelastic properties of porcine myofibrillar proteins prepared from different muscles (semimembranosus (SM), longissimus dorsi (LD) and psoas major (PM)) during heat-induced gelation. Dynamic rheological properties were measured while heating at 1 °C/min from 20 to 85 °C, followed by a holding phase at 85 °C for 3 min and a cooling phase from 85 to 5 °C at a rate of 5 °C/min. Storage modulus (G′, the elastic response of the gelling material) increased as gel formation occurred, but decreased after reaching the temperature of myosin denaturation (52 °C) until approximately 60 °C when the gel strength increased again. This resulted in a peak and depression in the thermogram. Following 60 °C, the treatments maintained observed trends in gel strength, showing SM myofibrils produced the strongest gels. Myofibrillar protein from SM and PM formed stronger gels at pH 6.0 than at pH 6.5. Differences may be attributed to subtle variations in their protein profile related to muscle type or postmortem metabolism. Significant correlations were determined between G′ at 57, 72, 85 and 5 °C, indicating that changes affecting gel strength took effect prior to 57 °C. Muscle type was found to influence water-holding capacity to a greater degree than pH.     

Effect of CMC Molecular Weight on Acid‐Induced Gelation of Heated WPI‐CMC Soluble Complex

Acid‐induced gelation properties of heated whey protein isolate (WPI) and carboxymethylcellulose (CMC) soluble complex were investigated as a function of CMC molecular weight (270, 680, and 750 kDa) and concentrations (0% to 0.125%). Heated WPI‐CMC soluble complex with 6% protein was made by heating biopolymers together at pH 7.0 and 85 °C for 30 min and diluted to 5% protein before acid‐induced gelation. Acid‐induced gel formed from heated WPI‐CMC complexes exhibited increased hardness and decreased water holding capacity with increasing CMC concentrations but gel strength decreased at higher CMC content. The highest gel strength was observed with CMC 750 k at 0.05%. Gels with low CMC concentration showed homogenous microstructure which was independent of CMC molecular weight, while increasing CMC concentration led to microphase separation with higher CMC molecular weight showing more extensive phase separation. When heated WPI‐CMC complexes were prepared at 9% protein the acid gels showed improved gel hardness and water holding capacity, which was supported by the more interconnected protein network with less porosity when compared to complexes heated at 6% protein. It is concluded that protein concentration and biopolymer ratio during complex formation are the major factors affecting gel properties while the effect of CMC molecular weight was less significant.     

Dynamic high pressure-induced gelation in milk protein model systems

The structure-functional properties of milk proteins are relevant in food formulation. Recently, there has been growing interest in dynamic high-pressure homogenization effects on the rheological-structural properties of food macromolecules and proteins. The aim of this work was to evaluate the effects of different homogenization pressures on rheological properties of milk protein model systems. For this purpose, sodium caseinate (SC) and whey protein concentrate (WPC) were dispersed at different concentrations (1, 2, and 4%), pasteurized, and then homogenized at 0, 18 MPa (conventional pressure, CP), 100 MPa (high pressure, HP), and 150 MPa (HP+). Differences in viscosity were observed between WPC and casein dispersions according to concentration, heat treatment, and homogenization pressure. Mechanical spectra described the characteristic behavior of solutions except for the WPC 4% pasteurized sample, in which a network formed but was broken after homogenization. Dispersions with different ratios of WPC and SC were also made. In these systems, pasteurization alone did not determine network formation, whereas homogenization alone promoted cold gelation. A total concentration of at least 4% was required for homogenization-induced gelation in pasteurized and unpasteurized samples. Gels with higher elastic modulus (G′) were obtained in more concentrated samples, and a bell-shaped behavior with the maximum value at HP was observed. The HP treatment produced stronger gels than the CP treatment. Similar G′ values were obtained when different concentrations, pasteurization conditions, and homogenization pressures were combined. Therefore, by setting appropriate process conditions, systems or gels with tailored characteristics may be obtained from dispersions of milk proteins.     

Gel mechanical properties of milk whey protein–dextran conjugates obtained by Maillard reaction

The effect of Maillard reaction on the mechanical properties of whey protein isolate (WPI) heat-induced gels was evaluated. WPI and dextran (15–25 kDa) conjugates were obtained by controlled dry heating during storage at 60 °C and 63% relative humidity for 2, 5 and 9 days. Changes in browning intensity and content of free amino groups were used to estimate the Maillard reaction. A decrease in free amino groups of WPI was observed when increasing polysaccharide concentration and reaction time. An increase in both a* and b* CIE Lab colour parameters indicated the development of a reddish-brown colour, typical of the Maillard reaction. Uniaxial compression and stress relaxation tests were performed to measure the mechanical properties of mixed and conjugate gels. Maillard reaction significantly modified the mechanical properties of WPI/DX gels, and even prevented fracture when conjugate gels were subjected to 80% deformation in uniaxial compression test.     

Comparative study of denaturation of whey protein isolate (WPI) in convective air drying and isothermal heat treatment processes

The extent and nature of denaturation of whey protein isolate (WPI) in convective air drying environments was measured and analysed using single droplet drying. A custom-built, single droplet drying instrument was used for this purpose. Single droplets having 5 ± 0.1 μl volume (initial droplet diameter 1.5 ± 0.1 mm) containing 10% (w/v) WPI were dried at air temperatures of 45, 65 and 80 °C for 600 s at constant air velocity of 0.5 m/s. The extent and nature of denaturation of WPI in isothermal heat treatment processes was measured at 65 and 80 °C for 600 s and compared with those obtained from convective air drying. The extent of denaturation of WPI in a high hydrostatic pressure environment (600 MPa for 600 s) was also determined. The results showed that at the end of 600 s of convective drying at 65 °C the denaturation of WPI was 68.3%, while it was only 10.8% during isothermal heat treatment at the same medium temperature. When the medium temperature was maintained at 80 °C, the denaturation loss of WPI was 90.0% and 68.7% during isothermal heat treatment and convective drying, respectively. The bovine serum albumin (BSA) fraction of WPI was found to be more stable in the convective drying conditions than β-lactoglobulin and α-lactalbumin, especially at longer drying times. The extent of denaturation of WPI in convective air drying (65 and 80 °C) and isotheral heat treatment (80 °C) for 600 s was found to be higher than its denaturation in a high hydrostatic pressure environment at ambient temperature (600 MPa for 600 s).