柔性机械臂的双时间尺度组合控制

本文研究柔性机械臂的轨迹跟踪和振动抑制问题. 首先, 利用Lagrange法和假设模态法建立柔性机械臂的动态模型, 进而利用奇异摄动理论得到柔性机械臂的双时间尺度模型. 然后, 基于慢时间尺度模型利用滑模控制理论设计轨迹跟踪控制器; 借助于快时间尺度模型利用自适应动态规划设计参数不精确已知情况下的最优振动抑制控制器; 将二者相结合, 构造双时间尺度组合控制器, 利用奇异摄动理论证明闭环系统稳定. 最后, 在Matlab/Simulink环境下进行实验, 与现有方法相比, 本文设计的控制器对柔性振动具有更好的振动抑制效果, 跟踪精度更高.     

针对执行器非光滑反向间隙-饱和的柔性立管边界控制

研究了针对执行器非光滑反向间隙-饱和约束特性的深海柔性立管系统振动控制和全局稳定问题.为了实现控制效果和品质,引入辅助系统和函数设计边界控制策略,以抑制立管系统振动并消除混合的反向间隙-饱和输入非线性影响.采用严格的分析且无需求助于模型降阶,所研发的控制器确保闭环系统在Lyapunov意义下的一致有界稳定性.通过选取恰当的设计参数,仿真结果验证了所设计控制器的控制性能.能.     

海洋柔性立管输出反馈边界控制

针对耦合内流动力学的海洋柔性立管系统,为了提高其振动控制品质,结合Lyapunov直接法和高增益观测器理论设计了输出反馈边界控制和干扰观测器,用以抑制结构振动偏移量和减弱外部环境干扰载荷的影响.其后,证明了闭环系统解的存在性、唯一性和收敛性及闭环状态的一致有界性.此外,本文的控制设计和稳定性分析是基于立管的原始无穷维动力学进行的,因此关于模型截断法产生的控制溢出问题将不会产生.最后仿真结果验证了本文所提出的输出反馈边界控制器能有效抑制柔性立管的振动.     

一类不确定T-S模糊时滞系统新的滑模控制方法

针对一类时滞不确定系统,基于模糊滑模控制方法,考虑了其镇定问题.所研究系统中的时滞项和参数不确定项分别为有界时变和非匹配的.首先设计滑模面,使得系统状态在滑模面保持指数渐近稳定,并且将系统的稳定性证明转化为线性矩阵不等式的解的存在性问题;其次,基于到达条件,构造控制器,使得系统在设计控制器的作用下在有限时间内到达切换面;最后,给出仿真算例,经验证说明所设计的控制器的有效性.     

基于干扰观测器的一类不确定非线性系统自适应二阶动态terminal滑模控制

针对一类不确定非线性系统的跟踪控制问题,在考虑建模误差、参数不确定和外部干扰情况下,以其拥有良好的跟踪性能以及强鲁棒性为目标,提出基于回归扰动模糊神经网络干扰观测器(recurrent perturbation fuzzy neural networks disturbance observer,RPFNNDO)的鲁棒自适应二阶动态terminal滑模控制策略.将回归网络、模糊神经网络和sine-cosine扰动函数各自优势相结合,给出一种回归扰动模糊神经网络结构,提出RPFNNDO设计方法,保证干扰估计准确性;构造基于带有指数函数滑模面的二阶快速terminal滑模面,给出其控制器设计过程,避免了滑模到达阶段、传统滑模的抖振问题,采用具有指数收敛的鲁棒项抑制干扰估计误差对系统跟踪性能的影响,利用Lyapunov理论证明闭环系统的稳定性;将该方法应用于混沌陀螺系统同步控制仿真实验,结果表明所提方法的有效性.     

基于积分滑模控制的非理想变时滞 神经网络有限时间同步

研究一类非理想变时滞神经网络的有限时间同步问题.首先,利用驱动-响应概念推导误差系统,并运用同步误差构造一个合适的积分滑模流型,若误差系统的状态轨迹在有限时间内到达滑模面,则同步误差将随其后在有限时间内收敛于零.然后,结合神经元激活函数的约束条件,设计一种合适的滑模控制器,根据所设计的控制器和Lyapunov稳定性理论,误差系统的状态轨迹能够在有限时间内到达滑模面,从而非理想变时滞神经网络的有限时间同步能够实现.最后,通过数值仿真结果验证所提出设计方法的有效性.     

基于有限时间的一类时滞非线性切换系统滑模控制

研究一类时滞非线性切换系统的有限时间滑模控制问题.针对所研究的系统模型,构造每个子系统对应的积分滑模面,基于滑模控制理论,设计带有状态时滞的滑模控制器使得每个子系统能在有限时间内到达相应的滑模面上,并对系统中存在的非线性项采用Lipschitz条件进行处理.根据多李亚普诺夫函数、平均驻留时间方法以及分割策略引理,给出滑模趋近段和滑模动态有限时间有界的充分条件,并通过对线性矩阵不等式的求解得到控制器增益.最后,通过一个数值仿真例子验证该设计方法的有效性.     

一类不确定线性切换系统的鲁棒H∞滑模控制

对一类含有非匹配不确定性且有外部干扰的线性切换系统,研究了H∞滑模变结构控制问题.利用LMI技术和单Lyapunov函数方法,设计单H∞滑模面,切换律以及子系统的变结构控制器,确保了切换系统的闭环系统为鲁棒稳定,且具有H∞扰动衰减度γ.系统状态到达滑模面后,该滑模面成为切换系统的全局鲁棒滑模面,可提高系统的暂态性能和鲁棒性.仿真例子说明所提出设计方法的有效性.     

带状态约束的非线性系统单向辅助面滑模控制

针对带有状态输出有界约束的一类不确定仿射非线性系统,提出一种单向辅助面滑模控制器设计方法．该方法通过将状态量的约束条件引入单向辅助面的设计,并利用单向辅助面构成系统状态输出量正不变集的边界,以保证系统状态能够满足状态输出量的约束条件．随后给出了该方法稳定性以及单向辅助面构成正不变集的理论证明,并通过仿真验证了所提出的设计方法的有效性．     

基于干扰观测器的航天器非奇异终端二阶滑模控制

为了消除干扰力矩和结构不确定性对卫星姿态控制性能的影响,本文提出了一种基于新型干扰观测器的非奇异终端二阶滑模控制方法.首先,文章设计了一种基于跟踪微分器的干扰观测器,来对卫星系统中的不确定项进行估计,利用估计值进行补偿,并保证估计误差在有限时间内收敛.在此基础上,文章设计一个非奇异终端滑模面,当系统到达滑模面时,姿态误差可以在有限时间内收敛,并利用二阶滑模趋近律设计控制器,保证系统在有限时间到达滑模面.在干扰观测器误差未完全收敛时,滑模控制器可以对存在的扰动进一步抑制,实现姿态跟踪系统的有限时间稳定,并通过李雅普诺夫方法严格证明了其稳定性.最后,仿真结果表明,干扰估计值误差可以在有限时间内收敛,证明了该控制方法对存在的干扰是具有较好的鲁棒性.     

Adaptive sliding mode control for discrete-time multi-input multi-output systems

In this paper, robust adaptive sliding mode tracking control for discrete-time multi-input multi-output systems with unknown parameters and disturbance is considered. The robust tracking controller is comprised of adaptive control and sliding mode control design. Bounded motion of the system around the sliding surface and stability of the global system in the sense that all signals remain bounded are guaranteed. If the disturbance and the reference signal are slowly varying with respect to the sampling frequency, the proposed sliding mode controller can reject the disturbance and output tracking can be approximately achieved. Simulation results are presented to illustrate the proposed approach.     

A STABLE SELF-LEARNING OPTIMAL FUZZY CONTROL SYSTEM

The issue of developing a stable self-learning optimal fuzzy control system is discussed in this paper. Three chief objectives are accomplished: 1) To develop a self-learning fuzzy controller based on genetic algorithms. In the proposed methodology, the concept of a fuzzy sliding mode is introduced to specify the system response, to simplify the fuzzy rules and to shorten the chromosome length. The speed of fuzzy inference and genetic evolution of the proposed strategy, consequently, is higher than that of the conventional fuzzy logic control. 2) To guarantee the stability of the learning control system. A hitting controller is designed to achieve this requirement. It works as an auxiliary controller and supports the self-learning fuzzy controller in the following manner. When the learning controller works well enough to allow the system state to lie inside a pre-defined boundary layer, the hitting controller is disabled. On the other hand, if the system tends to diverge, the hitting controller is turned on to pull the state back. The system is therefore stable in the sense that the state is bounded by the boundary layer. 3) To explore a fuzzy rule-base that can minimize a standard quadratic cost function. Based on the fuzzy sliding regime, the problem of minimizing the quadratic cost function can be transformed into that of deriving an optimal sliding surface. Consequently, the proposed learning scheme is directly applied to extract the optimal fuzzy rulebase. That is, the faster the hitting time a controller has and the shorter the distance from the sliding surface the higher fitness it possesses. The superiority of the proposed approach is verified through simulations.     

集成神经网络与自适应算法的分数阶滑模控制

针对被控对象的参数时变和外部扰动问题,本文融合神经网络的万能逼近能力和自适应控制技术,并结合分数阶微积分理论,提出了基于神经网络和自适应控制算法的分数阶滑模控制策略.本文采用等效控制的方法设计滑模控制律,并利用神经网络的万能逼近能力估测控制律的变化,结合自适应控制算法和分数阶微积分理论抑制传统滑模控制系统的抖震,同时根据Lyapunov稳定性理论分析了系统的稳定性,最后给出了实验结果.实验结果表明,本文提出的基于神经网络和自适应控制算法的分数阶滑模控制系统,能保持滑模控制器对系统外部扰动和参数变化鲁棒性的同时,也能有效地抑制抖震,使得系统获得较高的控制性能.     

Chattering‐free adaptive sliding mode control for continuous‐time systems with time‐varying delay and process disturbance

This paper concerns the controller design for continuous‐time linear systems with time‐varying delay and process disturbance. A novel adaptive sliding mode control law is mainly proposed to attract the sliding mode to first‐order sliding surface within a finite time; afterwards, the uniformly ultimately bounded stability of the closed‐loop system on the sliding surface is simultaneously guaranteed. In addition, the chattering phenomena can be conveniently excluded if the disturbance is a low‐intensity process. Once the high‐intensity disturbance is involved, the state variation can be significantly reduced as well. Furthermore, by the technique of a novel exponential free‐matrix technique, the convergence rate of the closed‐loop system can be conveniently preregulated. Numerical example is provided to demonstrate the effectiveness of the proposed method.     

Design of a Sliding Mode Controller with Fuzzy Rules for a 4-DoF Service Robot

In this study, a novel control strategy that combines a fuzzy system and the sliding mode controller is proposed for improving stability and achieving high-accuracy control in service robots. Based on the kinematic and dynamic models of a 4-degrees of freedom manipulator, and the observed tracking error using a low-cost inertial sensor, the proposed fuzzy sliding mode controller (FSMC(IMU)) is designed to generate appropriate torques at robot joints. The FSMC(IMU) controller parameters are adjusted through a fuzzy rule that determines the state of the system. The error in trajectory tracking is reduced through this. The gain value K can be finely adjusted by fuzzy control by observing the degree of vibration after entering the sliding mode surface. The larger the observed vibration value, the faster the fuzzy controller follows the given input trajectory by selecting a smaller gain value K and reducing jitter due to the sliding mode control’s discontinuous switch characteristics. When the degree of error is small, it achieves faster and more accurate control performance than when the observer is not used. The stability of the FSMC(IMU) system is verified via disturbance experiments. The experimental data are compared with the conventional sliding mode controller and proportional-derivative control. The experimental results demonstrate that the proposed FSMC(IMU) controller is stable, fast, and highly accurate in controlling service robots.

     

离散时间系统的滑模控制器设计与仿真研究

针对不确定性离散时间系统,分析和设计了一类变结构控制器。当存在外界干扰和不确定性时,系统状态也是全局有界稳定的。一个新的切换面作为系统的输出信号被提出,特别用来设计滑模控制器。系统状态一旦进入到准滑动模态,就对设备参数变化和外界干扰显示出强的鲁棒性,因为控制器的设计完全考虑了边界层的影响。外推法被用来估计不确定离散时间系统的不确定值。两种方法均有效地消除了系统的抖振,确保了系统的稳定性,且保证了变结构控制系统良好的品质。最后,仿真结果证实了所提出方法的有效性。     

Buck变换器的改进型互补滑模控制

针对Buck变换器系统中存在匹配和不匹配干扰的问题, 本文提出了一种基于干扰观测器(DOB)的改进型互补滑模控制(CSMC)策略. 首先, 建立存在多重干扰的Buck变换器数学模型, 将模型改写为标准二阶积分型控制对象, 将式中干扰统一为匹配干扰和不匹配干扰. 其次, 设计2个DOB分别估计匹配干扰和不匹配干扰, 实现有限时间内跟踪干扰信号, 以抵消各种不确定性对系统的影响. 然后, 设计互补滑模面, 提出基于等效控制的改进型互补滑模控制律, 保留边界层内鲁棒性的同时, 提升控制器的动态性能, 减小静态误差, 拓宽边界层参数选择范围. 最后, 基于李雅普诺夫理论证明所提出控制器的稳定性. 数字仿真表明, 提出的改进型CSMC控制器结合DOB的总体控制方案能够有效抑制系统匹配和不匹配干扰, 同时获得更快的收敛速度以及更高的跟踪精度.     

ROBUST VIBRATION CONTROL FOR FLEXIBLE ARMS USING THE SLIDING MODE METHOD

The vibration control of flexible arms is accomplished here using the sliding mode method, where the traditional discontinuous approach is modified by a differentiable one. The higher order modes of the flexible arm are treated as disturbances and are compensated by introducing a disturbance observer. Simplified expressions of the motor angular and the strain moment for the flexible arm with a disturbance observer are obtained, where the remaining disturbance and the model uncertainties are considered as system uncertainties. The robustness of the sliding mode control is effectively employed to cope with the system uncertainties, where the bounds of the uncertainties are adaptively updated. The proposed control law simultaneously causes the motor angular to track a desired signal and the strain moment to approach zero. The stability of the controlled flexible arm is analyzed based on the obtained important fact that a part of the control input is the approximate estimate of a special signal generated by the uncertainty. The motor angular tracking error and the converging speed of the controlled signals are determined by means of design parameters. Experimental results demonstrate the robustness of the proposed method.     

有限时间收敛的Terminal滑模控制设计

讨论了一类SISO非线性系统的滑模变结构控制有限时间收敛问题,提出一种新的Terminal滑动模态及相应控制的设计方法,可用于带有外部扰动的二阶非线性系统。研究结果表明,系统状态在滑模面上能以较快的速度达到平衡点,在滑模面上到达平衡点的时间均是有限的,并且与普通的Terminal滑模相比,在滑模面上能以更短的时间到达平衡点。仿真结果表明了所提方法的有效性。     

Robust control of a hydraulically driven flexible arm

A new robust controller is proposed to regulate both flexural vibrations and rigid body motion of a hydraulically driven flexible ann. The controller combines backsteppmg control and sliding mode to arrive at a controller capable of dealing with a nonlinear system with uncertainties. The sliding mode technique is used to achieve an asymptotic joint angle and vibration regulation in the presence of payload uncertainty by providing a virtual torque input at the joint while the backstepping technique is used to regtthte the spool position of a hydraulic valve to provide the required torque. It is shown that there is no chatter in the hydraulic valve, which results in smoother operation of the system.