EP/PUR梯度互穿网络聚合物的制备及其拉伸性能研究

提出一种新的方法对梯度互穿网络聚合物(IPNs)中梯度组分的分布进行设计,并采用逐层浇注的方法制备了不同层数的环氧树脂/聚氨酯(EP/PUR)IPNs,对其拉伸性能进行了研究。研究结果表明,EP/PUR梯度IPNs的拉伸性能受梯度层数的影响,梯度层数越多,拉伸弹性模量越小,拉伸强度高,但当梯度层数超过7层后,拉伸强度有所降低;EP/PUR梯度IPNs的拉伸性能优于EP和EP/PUR普通IPNs。     

梯度层数对聚氨酯／环氧梯度互穿网络聚合物力学性能的影响

设计了一种新的梯度组分分布数学模型，采用梯度因子和梯度层数控制梯度组分的分布，并采用逐层浇铸的方法制备了不同层数的EP／PU梯度互穿网络聚合物（IPN）材料；测试了材料的拉伸性能、弯曲性能以及冲击性能；研究了梯度层数变化对这些性能的影响，并同普通IPN的性能进行了对比。研究结果表明，在相同质量比和梯度因子情况下，梯度层数越多，拉伸强度和冲击强度越高，弯曲强度越低。梯度IPN的拉伸强度和冲击强度均高于普通IPN，弯曲强度低于普通IPN。     

聚氨酯/乙烯基树脂互穿聚合物网络的研究进展

综述了聚氨酯/乙烯基树脂互穿聚合物网络（PU/VER IPNs）中两组分的聚合机理;重点讨论了分步IPNs、同步IPNs和胶乳IPNs的制备方法及其研究进展;介绍了PU/VER IPNs合成动力学的研究方法,包括化学滴定法、差示扫描量热法和傅立叶变换红外光谱法。     

互穿网络聚合物研究及其应用进展

综述了互穿网络聚合物(IPNs)的分类、结构和制备材料,着重讨论了IPNs在各方面的应用,指出了目前IPNs材料制备存在的问题,并对今后IPNs的制备和研究进行了展望,提出了制备IPNs新思路.     

增韧改性环氧树脂互穿网络聚合物的合成与表征

合成了端异氰酸酯/环氧丙烯酸树脂互穿网络聚合物,在环氧树脂交联网络中引入柔性链段,达到增韧的目的。通过改变端异氰酸酯和环氧丙烯酸树脂的组分比,合成不同组成的互穿网络聚合物(IPNs)。借助红外光谱和扫描电镜等分析方法,研究了IPNs的分子混合形态结构。同时采用差热分析法(DSC)测试了聚合物的玻璃化转变温度,结果表明:端异氰酸酯预聚体含量越高,聚合物的玻璃化转变温度越低。对成膜物的力学性能研究表明,INPs的拉伸强度在端异氰酸酯/环氧丙烯酸树脂比例为30:70时,拉伸强度为55.24 MPa,是纯环氧树脂的2.5倍。     

DCPDE/PUR互穿聚合物网络的制备与表征

以聚氨酯(PUR)预聚体、二氧化双环戊二烯环氧树脂(DCPDE)为基体,分别以顺丁烯二酸酐(MA)和甘油为固化剂和促进剂,制备了新型DCPDE/PUR互穿聚合物网络(IPNs)复合材料。采用红外光谱法、热重分析法和差示扫描量热法等手段对该IPNs材料的化学结构、热性能和力学性能进行了表征。结果表明,PUR加入DCPDE固化体系,形成了IPNs结构,提高了复合材料的韧性,降低了刚性。PUR质量分数为30%时,复合材料的拉伸强度相对稳定,冲击强度提高了16.4 kJ/m2,断裂伸长率提高了12.4%,弯曲强度略微降低;复合材料的热分解温度在360℃以上,热稳定性良好。     

环氧树脂/丙烯酸酯互穿网络聚合物及其流变性能研究

采用甲基六氢邻苯二甲酸酐( MeHHPA)作为新型脂环族环氧树脂(CER)的固化剂,选用过氧化二异丙苯为三羟甲基丙烷三甲基丙烯酸酯( TMPTMA)的引发剂,制备了一种新的CER/TMPTMA互穿网络聚合物( IPNs).通过扫描电子显微镜表征并证实了IPNs的形成过程.研究发现,由于TMPTMA的自由基聚合反应先于C...     

二氧化双环戊二烯环氧树脂/聚氨酯互穿聚合物网络的制备与性能研究

制备了新型二氧化双环戊二烯环氧树脂(DCPDE)/聚氨酯(PU)互穿聚合物网络(DCPDE/PU IPNs).采用红外光谱法对互穿聚合物网络的结构进行了表征.对不同固化体系的热稳定性、力学性能和涂膜的微观形貌进行了研究.研究结果表明:互穿聚合物网络的形成,提高了二氧化双环戊二烯环氧树脂的弯曲强度、附着力和耐冲击性.固化剂的加入改进了聚氨酯/环氧树脂互穿网络的耐热性能.增韧改性后的环氧树脂比改性之前的环氧树脂呈现明显的两相结构.     

环氧树脂/聚氨酯IPNs注浆材料的同步法制备及其性能研究

采用开环合成环氧树脂预聚体接枝聚氨酯,研究制备了开环环氧树脂(EP-OH)/聚氨酯(PU)同步互穿聚合物网络(IPNs)注浆材料。对复合注浆材料的结构、力学性能、蓄热性能进行了表征。结果表明,部分开环的环氧树脂可有效提高材料的力学性能,拉伸强度达到74.3 MPa,冲击强度为10.3 KJ/m~2,粘接强度最高达10.4 MPa。当EP-OH添加量为20%时,复合注浆材料的最高蓄热温度由原样的142℃降至118℃。     

二氧化双环戊二烯环氧树脂/聚氨酯互穿聚合物网络的制备及其性能

以N-对羧基苯基马来酰亚胺(CPMI)和乙二醇单双环戊二烯基醚(EMDCPE)为单体合成了新型共聚物(CPMI-co-EMDCPE),将其作为二氧化双环戊二烯环氧树脂(DCPDE)/聚氨酯(PU)互穿聚合物网络(IPNs)体系的固化剂,以期改善互穿聚合物网络之间的相容性和热性能.采用红外光谱法对固化剂及互穿聚合物网络的结构进行表征.对不同固化体系涂膜的热稳定性、力学性能和微观形貌进行了研究.研究表明,互穿聚合物网络的形成,提高了二氧化双环戊二烯环氧树脂的弯曲强度、附着力和抗冲击强度.新型固化剂的加入普遍提高了二氧化双环戊二烯环氧树脂/聚氨酯互穿聚合物网络的耐热性能,增韧改性后的环氧树脂呈现明显的两相结构.     

Mechanical properties of blocked polyurethane/epoxy interpenetrating polymer networks

The mechanical properties of blocked polyurethane(PU)/epoxy interpenetrating polymer networks (IPNs) were studied by means of their static and damping properties. The studies of static mechanical properties of IPNs are based on tensile properties, flexural properties, hardness, and impact method. Results show that the tensile strength, flexural strength, tensile modulus, flexural modulus, and hardness of IPNs decreased with increase in blocked PU content. The impact strength of IPNs increased with increase in blocked PU content. It shows that the tensile strength, flexural strength, tensile modulus, and flexural modulus of IPNs increased with filler (CaCO₃) content to a maximum value at 5, 10, 20, and 25 phr, respectively, and then decreased. The higher the filler content, the greater the hardness of IPNs and the lower the notched Izod impact strength of IPNs. The glass transition temperatures (T_g) of IPNs were shifted inwardly compared with those of blocked PU and epoxy, which indicated that the blocked PU/epoxy IPNs showed excellent compatibility. Meanwhile, the T_g was shifted to a higher temperature with increasing filler (CaCO₃) content. The dynamic storage modulus (E′) of IPNs increased with increase in epoxy and filler content. The higher the blocked PU content, the greater the swelling ratio of IPNs and the lower the density of IPNs. The higher the filler (CaCO₃) content, the greater the density of IPNs, and the lower the swelling ratio of IPNs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1826–1832, 2006     

Synthesis and mechanical properties of leather–epoxy interpenetrating polymer networks

Leather–epoxy interpenetrating polymer networks (IPNs) were synthesized; these IPNs have an approximate epoxy concentration of 25 wt %. The flexural and tensile moduli of the IPNs prepared are equivalent to those of the epoxy resin. The Izod impact energy and fracture toughness measured for the IPNs, however, exceed those attained by the epoxy resin alone by at least a factor of 4. The glass transition of leather–epoxy IPNs occurs over a wide temperature range, thus indicating that the IPN is an intimate admixture of the epoxy resin throughout the collagen matrix of the hide. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1224–1232, 2000     

Damping properties of interpenetrating polymer networks of polyurethane‐modified epoxy and polyurethanes

Interpenetrating polymer networks (IPNs) were prepared from polyurethane (PU)‐modified epoxy with different molecular weight of polyol and polyurethanes based on the mixture of polydiol and polytriol by a one‐shot method. Two types of PU‐modified epoxy: PU‐crosslinked epoxy and PU‐dangled epoxy were synthesized, and the effects of the different molecular weights of polyol in the PU‐modified epoxy/PU IPNs on the dynamic mechanical properties, morphology, and damping behavior were investigated. The results show that the damping ability is enhanced through the introduction of PU‐modified epoxy into the PU matrix to form the IPN structure. As the molecular weight of polyol in PU‐modified epoxy increases, the loss area (LA) of the two types of the IPNs increases. PU‐dangled epoxy/PU IPNs exhibit much higher damping property than that of the PU‐crosslinked epoxy/PU IPNs with 20 wt % of PU‐crosslinked epoxy. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 328–335, 1999     

环氧树脂改性聚氨酯耐热性能的研究

端异氰酸酯基聚氨酯预聚体与环氧树脂E-51形成了互穿网络,通过热重分析仪(TGA)研究了完全固化后的互穿网络的热分解行为、透射电镜研究了IPN的相分离行为,及拉伸强度、硬度等对其进行了表征。结果表明,经过环氧树脂改性的聚氨酯的耐热性能比纯聚氨酯得到了提高,且力学性能也有所改善,并对其机理进行了阐述。     

Interpenetrating polymer networks of bismaleimide and polyurethane-crosslinked epoxy

This study prepared an interpenetrating polymer network of bismaleimide and polybutylene adipate-based polyurethane-crosslinked epoxy (BMI/PU-EP IPN) using the simultaneous bulk polymerization technique. Infrared spectra analysis was also performed to identify the polyurethane-crosslinked epoxy (PU-EP). Also investigated herein were the mechanical properties including tensile strength, fracture energy, and Izod impact strength of various bismaleimide content in PU-EP matrix. In addition, differential scanning calorimetry and thermogravimetric analyses of the BMI/PU-EP IPN were conducted as well. Analyses results demonstrate that the bismaleimide was dissolved primarily in the polyurethane domains of the epoxy matrix to form a compatible system, thereby increasing the mechanical strength of the BMI/PU-EP IPNs. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 529–536, 1998     

Graft interpenetrating polymer networks of polyurethane and epoxy containing rigid rods in side chain

The rigid rod‐like 4,4′‐bis(6‐hydroxyhexyloxy)biphenyl (BHHBP) units were distributed in either the epoxy or polyurethane to become SR‐epoxy and PU (with or without BHHBP) polymer matrices. The interpenetrating polymer networks (IPNs) of PU (with or without BHHBP) and SR‐epoxy were synthesized through simultaneous polymerization, and connected each other via the grafting reaction between the ? NCO groups of the PU polymer network and the ? OH groups on the side chains of SR‐epoxy network. The thermal and mechanical characteristics, compatibilities, and morphologies of these PU (with or without BHHBP)/SR‐epoxy graft‐IPNs were investigated. The polyether‐type PU(PPG series)/SR‐ epoxy graft‐IPNs exhibited two‐phased morphologies (i.e., phase separation occurred), and higher fracture energies (G_IC). Whereas the polyester‐type PU(PBA series)/SR‐ epoxy graft‐IPNs were homogeneous (no phase separation), and exhibited higher tensile and Izod impact strengths. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

机织/针织混合铺层对复合材料力学性能的影响

为使纺织复合材料同时具有机织结构复合材料和针织结构复合材料的综合力学性能,通过混合铺层方式制备机织/针织混合结构复合材料。以芳纶机织平纹织物和针织罗纹织物为增强体,以环氧树脂为基体,调整复合材料中增强体的铺层顺序,利用真空辅助成型技术制备四层层压机织/针织混合结构复合材料。通过对复合材料拉伸性能、弯曲性能和冲击性能的测试,分析混合铺层和铺层顺序对芳纶环氧树脂复合材料力学性能的影响。结果表明,混合铺层和铺层顺序对芳纶环氧树脂复合材料的弯曲强度和冲击强度有较大影响,特别是对罗纹结构复合材料纬向弯曲强度和冲击强度的改善。当采用相同铺层方式,罗纹织物为受力面时,机织/针织混合结构复合材料具有较大弯曲强度和冲击强度。     

Studies on castor oil–based polyurethane/polyacrylonitrile interpenetrating polymer network for toughening of unsaturated polyester resin

Tricomponent interpenetrating polymer network (IPN) systems involving castor oil, toluenediisocyanate (TDI), acrylonitrile (AN), ethylene glycol diacrylate (EGDA), and general‐purpose unsaturated polyester resin (GPR) were prepared with various compositions. The structures of the IPNs at various stages were confirmed using FTIR. The thermal stability of the IPNs was studied using TGA, which indicated that the polyurethane/polyacrylonitrile/GPR (PU/PAN/GPR) IPN underwent single‐stage decomposition, showing perfect compatibility at the IPN composition of 10 : 90 (PU/PAN : GPR). The mechanical properties such as tensile, flexural, impact, and hardness for the IPNs with various compositions were determined. It was found that the tensile strength of the GPR matrix was decreased and flexural and impact strengths were increased upon incorporating PU/PAN networks. The swelling properties in water and toluene were also studied. The morphology of the IPNs was studied using SEM. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 817–829, 2004