反应体系组成对纳米SiO2/PS复合粒子粒径及分布的影响

研究了在纳米SiO2粒子表面的苯乙烯原位聚合反应中,反应体系的组成(单体、引发剂、稳定剂及纳米SiO2粒子用量)对纳米SiO2/PS复合粒子的形态、粒径大小及分布的影响。结果表明,当纳米SiO2粒子与单体质量比为5%,苯乙烯质量分数为25%,引发剂及稳定剂用量分别为单体用量(质量比)的0.15%和1.5%时,制备出的纳米SiO2/PS复合粒子呈球形,表面光滑无明显缺陷,颗粒之间分散性很好,粒径为0.923μm,分散系数为0.108。     

Au-SiO2复合纳米微球的制备与表征

采用溶胶-凝胶法制备SiO2纳米微球,以KH-550为粘结剂,利用简单的化学还原法,成功制备出Au-SiO2复合纳米微球,并通过扫描电子显微镜,透射电子显微镜,X射线衍射仪,紫外-可见分光光度计和多功能成像光电子能谱仪对其进行表征.结果表明,Au-SiO2复合纳米微球粒径约130 ～ 160 nm,且颗粒较均匀、分散性较好.样品中金纳米粒子均匀分散于SiO2纳米微球表面,粒径约4～9 nm,具有良好的面心立方结构,晶型良好,且Au物种主要以零价金属态存在.     

丙烯酸酯类聚合物乳液法修饰纳米SiO2粒子研究

采用带有羧基活性官能团的丙烯酸酯类聚合物乳液对纳米SiO2进行表面修饰.并用透射电镜、红外、热失重、接触角、粒径分析对处理效果进行了表征.结果表明所制备的含羧基基团的共聚物乳胶粒子在机械搅拌作用下,与粒径为15～20nm左右的无机SiO2纳米粒子的作用过程中,实现了对SiO2表面修饰和分散的效果.当复合温度(65℃)高于改性用聚合物的Tg(45℃)时,柔软的聚合物乳胶粒子变形、黏附在SiO2纳米粒子周围,并通过羧基的化学吸附作用最终实现对SiO2粒子的包覆;当复合温度(25℃)低于改性用聚合物的Tg(45℃)时,乳胶粒子仍保持其基本形状,SiO2粒子黏附在乳胶粒子周围.     

Ag@SiO_2核壳纳米粒子的制备与表征

以NaBH4作还原剂,TEOS为前体,采用反相微乳液法制得粒径50～100nm的Ag@SiO2核壳纳米粒子,其中Ag核为面心立方结构,壳层为无定形SiO2。考察催化剂加入的先后和微乳液R值(R=n水/n表面活性剂)对Ag@SiO2核壳纳米粒子形成的影响。用TEM、UV-Vis、XRD对纳米粒子的形貌及性质进行表征。结果表明:催化剂若先于TEOS加入,易得到Ag@SiO2核壳纳米粒子,随着R值的增加,Ag核的粒径变大,纳米粒子逐渐由单核变成多核。催化剂若后于TEOS加入,则形成负载型Ag/SiO2复合物。Ag核被SiO2壳包覆后的等离子共振吸收峰发生了微弱红移。而当壳厚80nm时,由于SiO2的散射作用,吸收峰会发生蓝移。     

硅酸乙酯为原料反相微乳液法制备纳米二氧化硅

采用NP-5/环己烷/去离子水体系制备反相微乳液,绘制了该体系的三元相图,并以正硅酸乙酯(TEOS)为原料,在碱性条件下受控水解反应制备了纳米SiO2粒子,探讨了[n(水)∶n(表面活性剂)](用R表示)和[n(水)∶n(TEOS)](用H表示)对SiO2纳米粒子粒径的影响。通过扫描电镜(SEM)和激光粒度仪对样品形貌和粒子大小和粒径分布进行了表征。结果显示:扫描电镜下观察到的SiO2粒子为无定型球形颗粒,粒径在200～500 nm的范围,激光粒度仪分析得到的平均粒径随着R和H的增大而增大。     

玻璃微珠/银核壳纳米复合粒子的制备及表征

通过添加聚合物表面活性剂,采用原位复合法制备了具有面心立方结构壳层的草莓状银包玻璃微珠核壳纳米复合粒子.用X射线衍射、扫描电镜及透射电镜等表征了复合粒子的形貌和结构.结果表明:随着溶液pH值的升高,反应速率加快,银的析出量增大,壳层银纳米粒子的特征峰也越强.十二烷基硫酸钠的加入使得表面呈蓬松态,而聚乙烯吡咯烷酮则使表面均匀致密,羧甲基纤维素钠使壳层颗粒生长呈不对称分布.随着银氨溶液浓度的增加,经液相还原的银纳米粒子相应增多,复合粒子壳层厚度也逐渐从30nm增大到52nm左右.     

直接从水玻璃合成表面修饰的纳米SiO2微粒

采用溶胶-凝胶法，以水玻璃为原料，在加入复合表面活性剂和分数剂的条件下，与乙酸反应直接得到纳米表面修饰的SiO2微粒。TEM照片显示，纳米SiO2颗粒为球形，粒度为10-30nm，统计平均粒径为20nm。     

液相共沉淀法制备四氧化三铁纳米粉

采用液相共沉淀法制备了纳米级四氧化三铁颗粒，通过X-Ray谱图证实了该粒子的组成结构。通过能谱图(EDS)研究表明样品中含有氯元素，这是因为在纳米级四氧化三铁颗粒表面处理过程中，其表面层与盐酸反应，表面生成氢氧化铁带电颗粒，Cl^-吸附在该颗粒表面，从而有效防止纳米粒子团聚，提高其分散效果。通过HRTEM研究表明，由该法所制得的四氧化三铁粒子主要为球形，粒径分布均匀，平均粒径在10nm左右。     

表面处理方式对纳米SiO2/PS复合粒子粒径及分布的影响

纳米SiO2粒子进行表面处理时所用表面活性剂的种类及用量直接影响二氧化硅/聚苯乙烯(SiO2/PS)复合粒子的粒径及分布。纳米SiO2粒子在超声波场作用下经十六烷基三甲基溴化胺(CTAB)处理后,可在纳米SiO2粒子表面形成单体和引发剂的富集区,在适当条件下引发以纳米SiO2粒子为核心的原位分散聚合反应。当纳米SiO2粒子对CTAB的吸附与初级粒子对聚乙烯吡咯烷酮(PVP)K-30的吸附达到动态平衡时,制备出的SiO2/PS复合粒子表面光滑,分散性好,仅有少量的游离纳米SiO2粒子存在,大部分纳米SiO2粒子被PS包裹。     

包覆型CeO_2/SiO_2和CeO_2/聚苯乙烯复合磨料的制备及其化学机械抛光性能

以SiO2和聚苯乙烯(polystyrene,PS)微球为内核,采用液相沉淀工艺制备了具有包覆结构的CeO2/SiO2和CeO2/PS复合颗粒。利用X射线衍射仪、透射电子显微镜、场发射扫描电子显微镜、X射线光电子能谱仪、动态光散射仪和zata电位测定等手段对所制备样品进行了表征。将所制备的CeO2/SiO2和CeO2/PS复合颗粒用于硅晶片热氧化层的化学机械抛光,用原子力显微镜(atomic force microscope,AFM)观察抛光表面的微观形貌、测量表面粗糙度。结果表明:所制备的CeO2/SiO2和CeO2/PS复合颗粒呈球形,粒径在150～200nm,CeO2纳米颗粒在SiO2和PS微球内核表面包覆均匀。包覆的CeO2颗粒与SiO2内核之间形成了化学键结合。CeO2颗粒的包覆显著的改变了复合颗粒的表面电性。AFM测量结果表明:经CeO2/SiO2和CeO2/PS复合磨料抛光后的硅热氧化片表面在5μm×5μm范围内粗糙度值分别为0.292nm和0.180nm。     

Dispersion of nanoparticles in poly(vinyl chloride) grains during In situ polymerization

Inorganic nanoparticles such as calcium carbonate, silica, or hydrotalcite were dispersed in vinyl chloride prior to suspension polymerization. That led to the production of poly(vinyl chloride) (PVC) composite grains with higher porosity and different internal morphology from those of commercial PVC. The PVC/composite grain sizes and their distribution were also influenced by the presence of nanofillers. The distribution of filler nanoparticles (either calcium carbonate or silica) was not uniform throughout the PVC grains. Regions of high and low filler concentration were observed. Regions of pure polymer were also observed. Reasons for that are suggested. Hydrotalcite did not remain in the PVC grains. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Ag/SiO_2复合颗粒的溶胶-凝胶法制备与表征

采用溶胶-凝胶法(Sol-gel)制备了不同形貌结构的纳米掺银复合颗粒.分析了掺银二氧化硅复合颗粒的形成机理,并采用透射电子显微镜(TEM)、扫描电子显微镜(SEM)、X射线衍射仪(XRD)、红外(FT-IR)及紫外可见(UV-Vis)光谱仪等手段对Ag/SiO_2复合颗粒的形貌结构进行了表征和分析.结果表明:复合颗粒(290 nm)尺寸均匀,近似球状,银颗粒(4 nm)均匀分布在二氧化硅表面,硅烷偶联剂KH-550影响了银粒子在复合颗粒中的分布状态,对Si-O-Si网络结构也有一定的影响,同时有效抑制了复合颗粒的团簇程度.     

PREPARATION OF ZINC OXIDE NANOPARTICLE VIA UNIFORM PRECIPITATION METHOD AND ITS SURFACE MODIFICATION BY METHACRYLOXYPROPYLTRIMETHOXYSILANE

Zinc oxide nanoparticles were prepared by uniform precipitation using urea hydrolysis. The ZnO precursor was slowly deposited from aqueous solution. Anionic surfactant was added into solution to block ZnO crystal growth and its agglomeration. Then ZnO nanoparticles were synthesized by the calcination of the precursor at high temperature. Transmission electron microscope (TEM) observation and particle size analyzer demonstrated that the ZnO nanoparticle exhibited nearly spheric shape with 10-40 nm particle size. The surface of the ZnO nanoparticle was modified by methacryloxypropyltrimethoxysilane (MPS). FT-IR (Fourier transform-infrared spectrophotometry) and XPS (X-ray photoelectron spectrophotometry) revealed that MPS was grafted onto the zinc oxide nanoparticle. XRD (X-ray diffraction) showed that the ZnO nanoparticle was a hexagonal crystal with a perfect crystalline structure, and its crystalline morphology was not altered through surface modification. The activation index (AI) of the modified ZnO nanoparticle was measured. It was found that the surface of the ZnO nanoparticle was changed from hydrophilicity into hydrophobicity via surface modification, implying the enhancement of its compatibility with organic polymers. FE-SEM (field scanning electron microscopy) showed that the modified ZnO nanoparticles were homogeneously dispersed in PVC matrices. Consequently, ZnO nanoparticles were integrated with PVC matrices by the grafting organic molecule.     

Growth mechanism and pH-regulation characteristics of composite latex particles prepared from Pickering emulsion polymerization of aniline/ZnO using different hydrophilicities of oil phases

A Pickering emulsion polymerization of aniline, using different hydrophilicities of oil phases, was stabilized by ZnO nanoparticles and performed to synthesize composite latex particles of polyaniline/ZnO. Ammonium peroxydisulfate (APS) was used as an oxidizing agent. The morphologies and growth mechanisms of the resulted composite latex particles were studied. The pH-regulation capacity of the composite latex particles was discussed. When toluene was used as the oil phase, the composite latex particles showed hollow structure, irregular morphology, and hundreds of nanometer in size. It was ascribed to the polymerization of aniline on the interfaces of droplets/water. ZnO nanoparticles, with 50-100 nm in size, acted as surfactants to stabilize the emulsion. When THF was used as an oil phase, the composite latex particles showed spherical morphology and enwrapping ZnO nanoparticles. It was attributed to the homogeneous nucleation of polyaniline in the aqueous phase. ZnO nanoparticles acted as templates for the polyaniline particles. The stability of the Pickering emulsion polymerization was affected by the volume ratio of the oil phase to water. The aqueous solution with pH 3-9 could simply be regulated to about pH 7 by the composite latex particles. It was contributed by the dissolution of ZnO nanoparticles and doping-dedoping of polyaniline in the acidic and alkaline aqueous solutions.     

PREPARATION OF ZINC OXIDE NANOPARTICLE VIA UNIFORM PRECIPITATION METHOD AND ITS SURFACE MODIFICATION BY METHACRYLOXYPROPYLTRIMETHOXYSILANE

Zinc oxide nanoparticles were prepared by uniform precipitation using urea hydrolysis. The ZnO precursor was slowly deposited from aqueous solution. Anionic surfactant was added into solution to block ZnO crystal growth and its agglomeration. Then ZnO nanoparticles were synthesized by the calcination of the precursor at high temperature. Transmission electron microscope (TEM) observation and particle size analyzer demonstrated that the ZnO nanoparticle exhibited nearly spheric shape with 10–40 nm particle size. The surface of the ZnO nanoparticle was modified by methacryloxypropyltrimethoxysilane (MPS). FT-IR (Fourier transform-infrared spectrophotometry) and XPS (X-ray photoelectron spectrophotometry) revealed that MPS was grafted onto the zinc oxide nanoparticle. XRD (X-ray diffraction) showed that the ZnO nanoparticle was a hexagonal crystal with a perfect crystalline structure, and its crystalline morphology was not altered through surface modification. The activation index (AI) of the modified ZnO nanoparticle was measured. It was found that the surface of the ZnO nanoparticle was changed from hydrophilicity into hydrophobicity via surface modification, implying the enhancement of its compatibility with organic polymers. FE-SEM (field scanning electron microscopy) showed that the modified ZnO nanoparticles were homogeneously dispersed in PVC matrices. Consequently, ZnO nanoparticles were integrated with PVC matrices by the grafting organic molecule.     

Pickering乳液聚合法CdS/PS荧光复合微球的制备与表征

通过水相合成法制备水溶性硫化镉(CdS)纳米晶,以CdS纳米晶固体粒子为乳化剂,进行Pickering乳液聚合制得CdS/PS荧光复合微球。通过SEM、XRD、FTIR、UV-vis、PL对CdS/PS荧光复合微球的微观结构、结晶情况及光学性能进行了分析和表征。结果表明,该复合微球具有以PS为核、CdS纳米晶为壳的核壳结构;复合微球的平均粒径为450nm;在复合微球中,CdS纳米晶仍然保持其量子尺寸效应,复合微球表现出了较好的荧光性能。     

(Ag)_核·(Au)_壳复合纳米粒子的制备

以银原子团簇作晶种,采用微波高压液相合成法制备了分散性好、规则球形的(Ag)核·(Au)壳复合纳米粒子。研究了(Ag)核·(Au)壳复合纳米粒子的紫外可见吸收光谱和共振散射光谱特性。结果表明,液相(Ag)核·(Au)壳复合纳米粒子和高压微波合成的液相金纳米粒子的最强共振散射峰均在580nm处,它们的吸收光谱图相似,最大吸收分别在518.5nm和524.8nm。     

Studies on the synthesis of electrospun PAN‐Ag composite nanofibers for antibacterial application

We have successfully synthesized polyacrylonitrile (PAN) nanofibers impregnated with Ag nanoparticles by electrospinning method at room temperature. Briefly, the PAN‐Ag composite nanofibers were prepared by electrospinning PAN (10% w/v) in dimethyl formamide (DMF) solvent containing silver nitrate (AgNO₃) in the amounts of 8% by weight of PAN. The silver ions were reduced into silver particles in three different methods i.e., by refluxing the solution before electrospinning, treating with sodium borohydride (NaBH₄), as reducing agent, and heating the prepared composite nanofibers at 160°C. The prepared PAN nanofibers functionalized with Ag nanoparticles were characterized by field emission scanning electron microscopy (FESEM), SEM elemental detection X‐ray analysis (SEM‐EDAX), transmission electron microscopy (TEM), and ultraviolet‐visible spectroscopy (UV‐VIS) analytical techniques. UV‐VIS spectra analysis showed distinct absorption band at 410 nm, suggesting the formation of Ag nanoparticles. TEM micrographs confirmed homogeneous dispersion of Ag nanoparticles on the surface of PAN nanofibers, and particle diameter was found to be 5–15 nm. It was found that all the three electrospun PAN‐Ag composite nanofibers showed strong antibacterial activity toward both gram positive and gram negative bacteria. However, the antibacterial activity of PAN‐Ag composite nanofibers membrane prepared by refluxed method was most prominent against S. aureus bacteria. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

微乳液法制备纳米二氧化硅基因传递复合载体

以硅酸盐溶液/环己烷/聚乙二醇辛基苯基醚/正戊醇体系的微乳液为原料反应,以浓硫酸为沉淀剂,采用微乳液法制备出了高比表面积纳米SiO2粉体,由BET,TEM,IR,XRD和DTA-TG对样品进行了形貌表征和物相分析。用多聚赖氨酸在纳米SiO2颗粒进行表面修饰,制得多聚赖氨酸/SiO2复合载体材料。结果表明：采用微乳液法制备的纳米SiO2粉末均由非晶态物质组成,粉体颗粒形貌呈近似球形,粒径为15～35nm,比表面积高达580～630m^2/g。通过脱氧核糖核酸(deoxyribonucleic acid,DNA)结合及细胞转染实验可知,该纳米复合颗粒能高效传递DNA进入鼻咽癌细胞株(human nasopharyngeal epithelioma 1,HNE1)内,并产生较好的绿色荧光蛋白。     

Preparation of albumin–ferrite superparamagnetic nanoparticles using reverse micelles

BACKGROUND: Micellar systems are widely applied as reactors to encapsulate inorganic nanoparticles in polymeric materials. However, only low inorganic contents and microscale dimensions are often achieved. RESULTS: The adsorption of albumin protein on ferrite nanoparticles permits to increase the stability of inorganic dispersions in water by inhibiting particle flocculation. Subsequent glutaraldehyde addition induces protein crosslinking and ferrite entrapment. Polymer–ferrite composite nanoparticles were obtained in this way. The magnetic albumin nanoparticles (25 nm mean diameter) obtained contain about 40 wt% of ferrite and show superparamagnetic behaviour. The composite powder was successfully functionalized with a model drug and the biological activity was evaluated. CONCLUSION: Using a reverse micelle approach, ferrite–albumin composite nanoparticles with a high inorganic content were obtained. The method permits the formulation of biocompatible magnetic particles of nanoscale dimensions. The exhibited superparamagnetic behaviour permits to hypothesize an application of the powder composite as a carrier in biomedical technologies. Copyright © 2009 Society of Chemical Industry