Stratified media theory interpretation of measurements of the spectral polarized directional emissivity of some oxidized metals

The emissivities of metals are strongly affected by the growth of oxide films. For small film thicknesses, perturbations are limited to the visible range. As thicknesses increase, they spread to the infrared range. Various samples of optically polished metals (Fe, Ni, Cr) and stainless steels (ELI.T 1803 MoT and AISI 304 or 316) have been oxidized at temperatures ranging from 400 to 800C. Their spectral polarized directional emissivities, and , have been measured with two experimental techniques. The spectral range studied extends from 0.4 to 14 m; the measurement directions vary between 0 and 80 from the normal to the sample. After measurement, each sample was analyzed by glowdischarge optical spectroscopy (GDOS). From the results of the analysis and from the survey of bibliographical data, we characterized the structure of the oxide films, i.e., their approximate thicknesses and compositions. If the complex optical indices of the metals and oxides are known, the stratified media theory enables the computation of the emissivities and . Computed and measured values have been compared. It appears that the theory accounts well for experimental data when the thicknesses of the oxides are small as in stainless steels. But for thicker oxide films, discrepancies are ascribed to several reasons.     

A simple theory for the cuprates: the Antiferro-magnetic van Hove scenario

A model of weakly interacting hole quasiparticles is proposed to describe the normal state of the high temperature superconductors. The effect of strong correlations is contained in the dispersion of the holes. Many-body effects induce anomalous quasiparticleflat bands similar to those observed in recent angle-resolved photoemission experiments. A model of weakly interacting hole quasiparticles is proposed to describe the physics of carriers in the cuprates. The model predicts superconductivity in the d_x2-_y2 channel, with a typical T_c 100K. The concept of optimal doping appears naturally in this model, as well as a large ratio 2/T _c 5.     

Study of the paramagnetic-antiferromagnetic transition and the γ → ε martensitic transformation in Fe-Mn alloys

The paramagnetic-antiferromagnetic transition and the martensitic transformation of Fe-Mn (Mn 15–32 wt%) alloys have been investigated by resistivity, dilatometry and X-ray diffraction (XRD). The results show that paramagnetic-antiferromagnetic transition increases the resistivity and the volume of alloys, whereas the martensitic transformation reduces the resistivity and volume of alloys. The A _f that was determined by the dilatometric method is not the temperature that martensites in the Fe-Mn alloys have reverse transformed to austenites completely. Mn additions reduce M _s, increase T _N and the lattice parameter of austenite in the Fe-Mn alloys. Both the antiferromagnetic transition and the martensitic transformation lead to an increase in the lattice parameter of austenite. The lattice parameters both above T _N and below T _N decrease linearly with temperature. The lattice parameter below M _s increases first and then decreases. Moreover, the (110) and (002) atomic planes in the Fe-15Mn-0.15C alloy are separated into two peaks: 2 for (002) is 44.16°, 2 for (110) is 44.47°.     

Investigations of the copper isotope effect in oxygen-deficient YBa2Cu3O7−δ

We present data on the copper isotope effect (⁶³Cu-⁶⁵Cu), C_u =-nT_c/nm_Cu, for two isotopic pairs of oxygen-deficient YBa₂Cu₃O_7–, where varies between 0.06 and 0.52. _Cu is below 0.01 at =0.06 (fully oxygenated), it takes values between –0.14 and –0.34 in the 60 K plateau. Larger negative values of _Cu are observed away from the plateau. The dependence of _Cu is similar to that of the pressure effect dnT_c/dP.     

Transport results from untwinned YBCO: Washboard frequency of the vortex lattice,and the quasiparticle mean free path

The washboard frequency of the moving vortex lattice in untwinned YBa₂ Cu₃ O_6.93 may be observed through mode-locking to an externally applied ac current of frequency _ext. The interference between and _ext results in jumps in the dc current-voltage characteristics when and _ext are harmonically related¹. The interference effect disappears in the vortex liquid state. The Hall conductivity _xy below T_c in YBCO contains contributions² from a positive quasiparticle (qp) term (H) and a negative vortex term (1/H). The qp term is surprisingly large well below T_c and implies a large gap anisotropy and a long qp mean free path (mfp). The thermal Hall effect³ _xy is closely related to the qp _xy; _xy is produced by asymmetric scattering of qp by pinned vortices. The qp mfp at H = 0, extracted from _xy and extended to low T by _xy, increases remarkably from 90 Å at T_c to more than 0.5m at 22 K.     

Constitution of the Ni3Cr-Ni3Al-Ni3W system

Isothermal sections of the Ni-Cr-Al-W system have been investigated at 75 at % Ni and temperatures of 1523 and 1273 K, by means of phase compositional analysis, X-ray diffraction and microscopical examination. The alloys studied lay in the range 2.5 to 10 at % Cr, 12.5 to 20 at% Al, 2.5 to 6.25 at % W, The phases formed were, and the bcc solid solution based on tungsten (designated ₂). The maximum extent of the region was found to be 3 at % each of chromium and tungsten. Preferential partitioning of tungsten to occurred. Study of an Ni-10Cr-12.5Al-2.5W alloy aged at 1273 and 1073 K, after quenching from 1573 K, showed that changes in and compositions and lattice parameters occur as a function of ageing time.     

Solution of thermal conductivity problems with boundary condition of the third kind and arbitrary coordinate and time dependence of the biot number

An analytical solution of the thermal conductivity problem with boundary conditions of the third kind and arbitrary coordinate and time dependence of the Biot number is found in the form of a converging series of quadratures.Notation , z dimensionless coordinates - dimensionless temperature - Q dimensionless volume heat-liberation density per unit time - Fo=/² Fourier number - Bi₁(, Fo)=(, Fo) · / Biot number - thermal diffusivity coefficient - plate thickness - time - (, Fo) heat-liberation coefficient - thermal conductivity coefficient - i summation index - Jo zero order Bessel function of the first kind Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 536–540, September, 1981.     

The Ni3Al-Ni3Cr-Ni3Mo section of the Ni-Cr-Al-Mo system

An investigation is reported of the constitution of the 75 at % nickel section of the Ni-Cr-Al-Mo system in the temperature range 1523 to 1073 K. Alloys in the region 10 to 20 at % Al were annealed at 1523, 1273, and 1073 K, respectively, and subjected to electron microprobe analysis, X-ray diffraction, and microscopical and hardness examination. Constitutional data are presented as partial isothermal sections and as vertical sections. At 1523 K the section consists only of fields containing ,+ and , the last mentioned phase being predominant. With decreasing temperature the and + fields increase in extent. Also, the NiMo and Ni₃Mo phases were encountered in the ternary Ni-Al-Mo alloy studied. The quaternary + alloys showed small lattice mismatch values, i.e. up to 0.25%. Raft like morphologies of were found in the quaternary alloys, resulting from directional coarsening. Observations of as-cast structures are also reported.     

Optical thermophysical characteristics of the condensed phase of combustion products and heatproof materials

An unconventional unit for experimentally studying the optical thermophysical properties of materials over a wide temperature range is described. Results are presented of studying the temperature function and dispersion of the absorption index for the condensed phase of the combustion products of a metalbearing fuel and of the emittance of fiber fireproof materials.Notation K spectral absorption coefficient - D spectral transmission coefficient - spectral absorption index - wavelength - d sample thickness - d_s surface layer thickness - I spectral intensity of radiation - , spectral and total emittances Kirov Polytechnical Institute. Kazan Chemical Engineering Institute, Russia. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 64, No. 3, pp. 330–336. March, 1993     

Complex microstructural changes in as-cast eutectoid Zn-Al alloy

Phase transformations and microstructural changes of an as-cast eutectoid Zn-Al alloy (ZnAl₂₂Cu₂) were investigated during isothermal holding. The typical dendritic structures consisted of _s phase as a core with the edge of decomposed _s phase and decomposed _s in the interdendritic regions. A series of complex phase transformations was observed. Both decompositions of _s and _s were determined at an early stage of ageing and a four-phase transformation, _f+T+, was observed at the boundaries of _f phase and the phase, instead of clearly observed at the boundaries of phase, in a solution-treated Zn-Al alloy during prolonged ageing.     

A note on the similarity solutions for free convection on a vertical plate

Summary The similarity solutions for free convection on a vertical plate when the (non-dimensional) plate temperature is x and when the (non-dimensional) surface heat flux is –x are considered. Solutions valid for 1 and 1 are obtained. Further, for the first problem it is shown that there is a value ₀, dependent on the Prandtl number, such that solutions of the similarity equations are possible only for >₀, and for the second problem that solutions are possible only for >–1 (for all Prandtl numbers). In both cases the solutions becomes singular as ₀ and as –1, and the natures of these singularities are discussed.     

Relationship between the energy supply parameters and the physicochemical l characteristics of polymer compositions during drying and thermal processing

The effect of the type of energy supply on the formation of temperature and concentration fields in the thermal processing of polymer compositions is considered.Notation T₀, T initial and current temperature of the coating - T_m temperature of the air - =(T-T_o)/(T_m-T₀) dimensionless temperature of the coating - a thermal diffusivity - A absorption power of the coating - D diffusion coefficient - thermal conductivity - c thermal capacity - density - _k convective heat transfer coefficient - i number of moles of reacting groups per unit volume of polymer - K₀ factor in front of the exponential - R gas constant - u concentration - Q thermal effect of the reaction - q_n density of the incident radiant flux - =x/ dimensionless coordinate over the thickness of the coating - Ki=Aq_n /(T_m-T₀) Kirpichev criterion characterizing the thermal effect of the reaction - Ki_p=Qi/c (T_m-T₀) analog of the Predvoditelev criterion, characterizing the rate of occurrence of a chemical excess in the system - Bu= Bouguer criterion - Lu=D/a Lykov number - Fo=a/² Fourier number - Bi= _k Biot number Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 26–33, July, 1980.     

Effect of magnesium content on the stress exponent and effective stress in the steady state creep of Al-Mg alloys

The stress exponent of steady state creep,n, and the internal ( _i) and effective stresses ( _e) have been determined using the strain transient dip test for a series of polycrystalline Al-Mg alloys creep tested at 300° C and compared with previously published data. The internal or dislocation back stress, _i, varied with applied stress,, but was insensitive to magnesium content of the alloy, being represented by the empirical equation _i=1.084 ^1.802. Such an applied stress dependence of _i can be explained by using an equation for _i of the form _i (dislocation density)^1/2 and published values for the stress dependence of dislocation density. Values of the friction stress, _f, derived using the equation _e/=(1–c) (1– _f/), indicate that _f is not dependent on the magnesium content. A constant value of _f can best be rationalized by postulating that the creep dislocation structure is relatively insensitive to the magnesium content of the alloy.On leave from Engineering Materials Department, University of Windsor, Windsor, Ontario N9B 3P4, Canada.     

Interaction between a dislocation and an impurity in KCl: Mg2+ single crystals

The interaction between a dislocation and the impurity in KCl: Mg²⁺ (0.035 mol% in the melt) was investigated at 77–178 K with respect to the two models: one is the Fleischer's model and the other the Fleischer's model taking account of the Friedel relation. The latter is termed the F-F. The dependence of strain-rate sensitivity due to the impurities on temperature for the specimen was appropriate to the Fleischer's model than the F-F. Furthermore, the activation enthalpy, H, for the Fleischer's model appeared to be nearly proportional to the temperature in comparison with the F-F. The Friedel relation between effective stress and average length of the dislocation segments is exact for most weak obstacles to dislocation motion. However, above-mentioned results mean that the Friedel relation is not suitable for the interaction between a dislocation and the impurity in the specimen. Then, the value of H(T _c) at the Fleischer's model was found to be 0.61 eV. H(T _c) corresponds to the activation enthalpy for overcoming of the strain field around the impurity by a dislocation at 0 K. In addition, the Gibbs free energy, G ₀, concerning the dislocation motion was determined to be between 0.42 and 0.48 eV on the basis of the following equation ln / = G ₀/(kT_p0)1 – (T/T _c)^{1/2 –1}(T/T _c)^1/2 + ln ₀/where k is the Boltzmann's constant, T the temperature, T _c the critical temperature at which the effective stress due to the impurities is zero, _p0 the effective shear stress without thermal activation, and ₀ the frequency factor.     

Specific analysis of EBSD data to study the texture inheritance due to the β → α phase transformation

A specific processing of EBSD data is proposed to study the texture inheritance of titanium or zirconium alloys. A non standard misorientation map is calculated to localise the colonies inherited from the same parent grain. The calculation of the parent orientation from its inherited variants detailed in previous works has been adapted to the data obtained from an automated EBSD analysis. Finally, a method to derive the orientation map of the parent phase from that of the inherited phase is proposed. The resulting and COMs are used to study some aspects of the variant selection occurring in the transformation of a T40 sample.     

Retention of a metastable bcc ε-Pu solid solution: ε-Pu(Ti)

A metastable -Pu (bcc) solid solution has been retained to room temperature by rapid quenching of Pu-rich Pu-Ti alloys from the liquid state. Until now, -Pu solid solutions were limited to high temperatures and had not been successfully quenched to room temperature without transformation. The apparatus used to quench the specimens was a modified gun-type splat-cooling unit, capable of producing extremely high cooling rates of from 10⁶ to 10⁸ ° C sec^–1. -Pu(Ti) was retained in the composition region from 20 to more than 45 at.% Ti, and extrapolation of the lattice parameter/composition curve yielded a value of a ₀ = 3.53₀ Å for -Pu at 20° C. This modification differs from the -Pu modification derived by extrapolating from high temperature to 20° C by a small valence increase of 0.1. Metastable -Pu (Ti) (fcc) solid solutions were also quenched-in with alloys containing lesser amounts of Ti, and evidence was found to indicate that the was probably a product of -Pu(Ti) solid-state decomposition.     

Varistor characteristics in PTCR-type (Ba,Sr)TiO3 ceramics prepared by single-step firing in air

This paper deals with donor, acceptor-codoped (Ba_0.4Sr_.6)TiO₃ ceramics with distinct varistor characteristics at room temperature, which were prepared by single-step firing in air. The materials, with the Curie point at around –90 °C, exhibited a large PTCR (positive temperature coefficient of resistivity) effect of more than seven orders of magnitude in the temperature range –90 °C (the resistivity 10³ · cm) to room temperature ( > 10¹⁰ · cm). An apparent dielectric constant of >20000 and tan < 0.05 (at 100 kHz) were observed for the present materials at room temperature, and moreover, the materials exhibited nonlinear current-voltage characteristics with the nonlinear coefficient, , in the range 7–12 and the varistor field, E_v, in the range 0.3–1.0 kV/cm. The value of in the present materials increased systematically with increasing in their PTCR temperature range. It has been found that there exists a close correlation between and the grain-boundary potential barrier height, e, obtained from the -T characteristic of the materials. An almost linear relationship was also found to exist between and log E_v for the present materials.     

Vibrational properties of wood along the grain

The dynamic Young's modulus (E_L) and loss tangent (tan _L ) along the grain, dynamic shear modulus (G_L) and loss tangent (tan _S) in the vertical section, and density () of a hundred spruce wood specimens used for the soundboards of musical instruments were determined. The relative acoustic conversion efficiency ( ) and a ratio reflecting the anisotropy of wood (, (E_L/G_L)(tan _S/tan _L)) were defined in order to evaluate the acoustic quality of wood along the grain. There was a positive correlation between and , and the variation in was larger than that in . It seemed logical to evaluate the acoustic quality of spruce wood by a measure of . By using a cell wall model, those acoustic factors were expressed with the physical properties of the cell wall constituents. This model predicted that the essential requirement for an excellent soundboard is smaller fibril angle of the cell wall, which yields higher and higher . On the other hand, the effects of chemical treatments on the and of wood were clarified experimentally and analyzed theoretically. It was suggested that the and of wood cannot be improved at the same time by chemical treatment.     

Effect of shot peening on the fatigue and fracture behaviour of two titanium alloys

The fatigue and fracture behaviour of two titanium alloys, the near-alpha IMI-685 and alpha-beta IMI-318, were studied in the machined and polished (MP) as well as the machined, polished and shot (glass-bead) peened (MPS) conditions. Glass-bead peening reduced the room-temperature as well as the high-temperature (450°C) fatigue life of alloy IMI-685 at high stress amplitudes, _a, approaching the proof stress, _ps, of the material (LCF region). When the applied stress amplitude (0–770 MPa, HCF region) was comparable to the peen-induced peak longitudinal residual stress, _LP, i.e. (_LP/a)=0.92, an improvement in the room-temperature fatigue life of IMI-685 was observed. When the (_LP/a) ratio was less than this value, decreases in the fatigue life were seen. The room-temperature fatigue behaviour of IMI-318 at high stress amplitudes was similar to that of IMI-685. The decrease in the fatigue life of this alloy, at a stress amplitude (770 MPa) where improvement was observed for IMI-685, could be attributed to the higher relaxation of peen-induced residual stresses in IMI-318 compared with IMI-685. Glass-bead peening improved the hightemperature (450°C) fatigue life of IMI-685 at a low stress amplitude (465 MPa; (_a/PS)=0.87). The crack-initiation sites in the MP and the MPS conditions were at the surface for both the alloys. However, fracture in the surface layers of the alloys appeared more brittle in the peened (MPS) rather than in the unpeened (MP) condition.