Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Imidazole/(HPO3)3‐doped sulfonated poly (ether ether ketone) composite membrane for fuel cells

A novel gel of imidazole/(HPO₃)₃ was synthesized and incorporated into sulfonated poly (ether ether ketone) (SPEEK) to fabricate composite proton exchange membranes. The composite membranes were characterized by alternating current impedance (AC), thermogravimetry (TG), differential scanning calorimetry (DSC), X‐ray diffraction (XRD), scanning electron microscope (SEM) and mechanical property test. Based on the electrochemical performance investigation, the proton conductivity of the membrane is intimately correlated with the temperature and the mass ratio of imidazole/(HPO₃)₃ in the composite. The SPEEK/imidazole/(HPO₃)₃?4 composite membrane (with 44.4 wt % of imidazole/(HPO₃)₃) has the optimized performance at 135°C. Mover, the strength of the composite membranes is almost comparable to that of Nafion membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41946.     

Synthesis and properties of fluorine‐ and siloxane‐containing polybenzimidazoles for high temperature proton exchange membrane fuel cells

In this study, new fluorine–siloxane‐containing polybenzimidazole (PBI) copolymers were synthesized by copolymerization of 3,3′‐diaminobenzidine, 2,2‐bis(4‐carboxyphenyl)‐hexafluoropropane (HFA), and 1,3 bis(carboxypropyl)tetramethyldisiloxane (BTMDS) with different molar ratios. PBI copolymer membranes were prepared by solution‐casting and then doped with phosphoric acid. The structures of PBI copolymers were characterized by FTIR and X‐ray diffraction. The solubility of the PBI copolymers was significantly increased by the introduction of the bulky HFA group and the flexible BTMDS group into the polymer backbone. The PBI copolymers still maintained good thermal stability and mechanical properties. Because of the introduction of the flexible and hydrophobic siloxane group in the polymer backbone, the methanol permeability was reduced and the proton conductivity under anhydrous condition at high temperatures was increased compared to the PBI without the siloxane group. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4107–4112, 2013     

Montmorillonite‐reinforced sulfonated poly(phthalazinone ether sulfone ketone) nanocomposite proton exchange membranes for direct methanol fuel cells

To produce a composite membrane with high conductivity and low permeability, SPPESK with a degree of sulfonation of 101% was carefully selected for the preparation of montmorillonite (MMT)‐reinforced SPPESK using solution intercalation. The fundamental characteristics such as water uptake, swelling ratio, proton conductivity, methanol permeability, and mechanical properties of the composite membranes were studied. Water uptake is improved when organic MMT (OMMT) loading increase. The composite membranes with CTAB‐MMT loading of 4–0.5% show 0.143–0.150 S cm^?1 proton conductivity at 80°C, which approaches the value of Nafion112. In addition, methanol permeability was decreased to 6.29 × 10^?8 cm² s^?1 by the addition of 6 wt % OMMT. As a result, the SPPESK‐MMT composite membrane is a good candidate for use in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39852.     

Synergistic effect of aluminium phosphate and tungstophosphoric acid on the physicochemical properties of sulfonated poly ether ether ketone nanocomposite membrane

This study explores the synergistic effect of aluminium phosphate (ALP) nanoparticles and tungstophosphoric acid (TPA) on the physicochemical properties of sulfonated poly ether ether ketone (SPEEK) nanocomposite membranes. SPEEK/TPA/ALP nanocomposite containing optimum TPA (10 wt %) and varying ALP content (3–10 wt %) are fabricated to investigate the effect of ALP nanoparticles on membrane properties. Experimental results reveal that nanocomposite membrane containing 3 wt % ALP nanoparticles and 10 wt % TPA exhibits 3.3 and 18.8 times higher proton conductivity compared to 10 wt % TPA filled SPEEK composite membrane and reference SPEEK membrane. ALP nanoparticles help in retaining water within the membranes and thus 59.4% reduction in water desorption rate is achieved compared to SPEEK/TPA membrane. The leaching of TPA is reduced by 34.5% which helps in retaining membrane properties. Membranes are thermally stable up to 200°C. Microstructure of the composite films is investigated by scanning electron microscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42952.     

Solution blown sulfonated poly(ether sulfone)/poly(ether sulfone) nanofiber‐Nafion composite membranes for proton exchange membrane fuel cells

A composite membrane of sulfonated poly(ether sulfone) (SPES)/poly(ether sulfone) (PES) nanofiber (NF) mat impregnated with Nafion was prepared and evaluated for its potential use as a proton conductor for proton exchange membrane (PEM) fuel cells. The supporting composite nanofibrous mat was prepared by solution blowing of a mixture of SPES/PES solution. The characteristics of the SPES/PES NF and the composite membrane, such as morphology, thermal stability, and performance of membrane as PEMs, were investigated. The performance of composite membranes was compared with that of Nafion117. The introduction of solution blown NFs to composite membranes modestly improved proton conductivity, water swelling, and methanol permeability. Therefore, composite membrane containing SPES/PES NFs can be considered as a novel PEM for fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42572.     

Novel imidazole‐grafted hybrid anion exchange membranes based on poly(2,6‐dimethyl‐1,4‐phenylene oxide) for fuel cell applications

Novel organic–inorganic hybrid membranes, based on poly(2,6‐dimethyl‐1,4‐phenylene oxide), have been prepared through 1,2‐dimethylimidazole functional groups and double crosslinking agents including 3‐glycidyloxypropyltrimethoxysilane and tetraethyl orthosilicate by sol–gel process for the purpose of improving the conductivity and alkaline resistance. The structure of membranes was characterized using Fourier‐transform infrared spectra, ¹H NMR, and X‐ray diffraction. The physico‐chemical properties of all membranes were shown in ion exchange capacity, water uptake, stability, and conductivity. Membranes with OH^– conductivity up to 0.022 at 25 °C and 0.036 S cm^?1 at 80 °C. Promisingly, the chemical stability of the resulting membranes remains unchanged after storage in 2 mol dm^?3 KOH at 25 °C over at least 10 days. The tensile strength can be higher than 30 MPa, and the elongation at break (Eb) is in the range 6.68–10.84%. Hence, this hybrid membrane can be potentially applied in alkaline fuel cells. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46034.     

A new sulfonated poly(ether sulfone) hybrid with low humidity dependence for high‐temperature proton exchange membrane fuel cell applications

A new sulfonated poly(ether sulfone) (PES) hybrid with low humidity dependence was prepared based on a new synthesized PES and Udel as a commercial PES. The PES was synthesized based on a pyridine containing diol which is able to change between pyridine and pyridinium salt forms during the cell performance (acidic condition) and facilitate proton transfer. The presence of nitrogen group increases inter and intramolecular interactions in the membrane and enhance proton hopping mechanism. Thermogravimetrical analysis of PES hybrid shows good thermal stability. Proton conductivity measurements were evaluated on a fuel cell test station, showing that the membrane has better performance under lower humidity (relative humidity = 60%) compare to the fully hydrated condition (relative humidity = 100%). The results reveal that proton transfer might be mainly accomplished through proton hopping mechanism at higher temperatures. The membrane also shows significant proton conductivity at 120 °C (about 6.6 mS cm^?1 at RH = 30%). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45342.     

Basicity‐based screening of aniline derivative for composite proton exchange membranes

The aim of this study was to find a suitable aniline derivative to develop composite sulfonated poly(ether ether ketone) (SPEEK) membranes and detail evaluation of their physico‐ and electrochemical properties. The hypothesis was high basicity of the aniline derivatives could form good composite membranes with better physicochemical and electrochemical properties. To assess the basicity we measured the zeta potentials of the polymers and correlated them with ion‐exchange capacities, water uptakes, transport numbers, water‐diffusion coefficients, conductivities, and methanol permeabilities. The obtained values of zeta potentials at pH 7 were 6.52, ?14.66, ?25.17, and ?28 for SPEEK/polynaphthalene (PNAPH), SPEEK/polyanisidine (PANIS), SPEEK/polyaniline (PANI), and SPEEK/polyxylindine (PXYL), respectively supports the hypothesis and strongly suggests polyaniline derivative's basicity‐dependent properties. Of the four derivatives (PNAPH, PANIS, PANI, and PXYL), the SPEEK/PXYL composite membrane had the lowest methanol permeability of 1 × 10^?4 cm²/s and highest proton conductivity of 161 mS/cm. These values are far better than the neat SPEEK and SPEEK/PANI composite. The suitability of SPEEK/PXYL can be explained by the high basicity of the PXYL composite membrane, which leads to the formation of effective Debye spheres, meaning that the ionic complex can interact with surrounding hydronium ions and form hydrophilic channels resulting in high proton conductivity and low methanol permeability. These results suggest that SPEEK/PXYL is a highly suitable membrane for methanol fuel cells or other electrochemical applications. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43978.     

Synthesis and properties of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) copolymers via atom transfer radical polymerization for proton exchange membrane

A series of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) (PP‐g‐PSN) copolymers were prepared via atom transfer radical polymerization (ATRP), followed by regioselective sulfonation which occurred preferentially at the poly(styrene‐co‐N‐benzylmaleimide) sites. The structures of these copolymers were confirmed by Fourier transform infrared (FTIR) spectroscopy, ¹H‐NMR, and ³¹P‐NMR, respectively. The resulting sulfonated PP‐g‐PSN membranes showed high water uptakes (WUs), low water swelling ratios (SWs), low methanol permeability coefficients, and proper proton conductivities. In comparison with non‐grafting sulfonated poly(bis(phenoxy)phosphazene) (SPBPP) membrane previously reported, the present membranes displayed higher proton conductivity, significantly improved the thermal and oxidative stabilities. Transmission electron microscopy (TEM) observation showed clear phase‐separated structures resulting from the difference in polarity between the hydrophobic polyphosphazene backbone and hydrophilic sulfonated poly(styrene‐co‐N‐benzylmaleimide) side chains, indicating effective ionic pathway in these membranes. The results showed that these materials were promising candidate materials for proton exchange membrane (PEM) in direct methanol fuel cell (DMFC) applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42251.     

Comparative study of composite membranes from nano‐metal‐oxide‐incorporated polymer electrolytes for direct methanol alkaline membrane fuel cells

A series of six composite membranes was prepared with two polymer electrolytes and three inorganic fillers, namely, silica, titania, and zirconia by a solution casting method. Two polymer electrolytes, that is, anion‐exchange membranes, were prepared from polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene (PSEBS) and polysulfone by chloromethylation and quaternization. A preliminary characterization of the ionic conductivity, methanol permeability, and selectivity ratio was done for all of the prepared composite membranes to check their suitability to work in direct methanol alkaline membrane fuel cells (DMAMFCs). The DMAMFC performance was analyzed with an in‐house fabricated single cell unit with a 25‐cm² area. Maximum performance was achieved for the composite membrane quaternized PSEBS/7.5% TiO₂ and was 74.5 mW/cm² at 60°C. For the comparison purposes, a commercially available anion‐exchange membrane (Anion Membrane International‐7001) was also investigated throughout the study. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structural and AC impedance studies on nanocomposite polymer electrolytes based on poly(ε‐caprolactone)

Nanocomposite polymer electrolyte (NCPE) films of [75 wt % poly(ε‐caprolactone) : 25 wt % zinc triflate] + x wt % nanofiller Al₂O₃ (x = 1, 3, 5, 7) were prepared by solution cast technique. Such NCPE films were characterized using Fourier transform infrared and AC impedance spectroscopic techniques. Complexation of polymer with salt and nanofiller was revealed from FTIR analysis. On the other hand, an apparent increase in the number density of charge carriers upto 5 wt % loading of the nanofiller was also confirmed. Furthermore, AC impedance spectroscopic studies have shown that ionic conductivity increases with the addition of Al₂O₃ and reaches a maximum of 2.5 × 10^?5 S cm^?1 at room temperature for 5 wt % loading of nanofiller. The dielectric behavior of all the synthesized samples has also been analyzed and presented. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40524.     

Quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone blend composite membrane doped with ZnO‐nanoparticles for alkaline fuel cells

A series of quaternized poly(2.6 dimethyl‐1.4 phenylene oxide)/polysulfone (QPPO/PSF) blend anion exchange membrane (AEM) were successfully fabricated and characterized for alkaline fuel cell application. Zinc oxide (ZnO) nanoparticles were introduced in the polymer matrix to enhance the intrinsic properties of the AEM. To confirm successful fabrication, Fourier‐transform infrared spectroscopy and nuclear magnetic resonance (¹H‐NMR) were used. The membrane properties were enhanced by the addition of ZnO nanoparticles. The addition of ZnO nanoparticles resulted to a higher ion exchange capacity (IEC) of 3.72 mmol g^?1, increase of ion conductivity (IC) up to 52.34 mS cm^?1 at 80 °C, enhancement of water uptake, and reduced methanol permeability. The QPPO/PSF/2% ZnO composite retained over 80% of its initial IC at room temperature and also retained over 50% of its initial IC at 80 °C when evaluated for alkaline stability. The maximum power output reached for the membrane electrode assembly constructed with QPPO/PSF/2%ZnO was 69 mW cm^?2 at room temperature, which is about three times more than the parent QPPO membrane. The above results indicate that QPPO/PSF/ZnO is a good candidate as an AEM for fuel cell application. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45959.     

Polyacrylonitrile‐based proton conducting membranes containing sulfonic acid and tetrazole moieties

Proton conducting membranes based on polymers containing sulfonic acid and tetrazole moieties were developed. Successful syntheses of poly(acrylonitrile‐co ‐styrene sulfonic acid) (PAN‐co ‐PSSA), poly(acrylonitrile‐co ‐5‐vinyl tetrazole) (PAN‐co ‐PVTz), and poly(acrylonitrile‐co ‐5‐vinyl tetrazole‐co ‐styrene sulfonic acid) (PAN‐co ‐PVTz‐co ‐PSSA) were confirmed by ¹H‐nuclear magnetic resonance spectroscopy, elemental analysis, and Fourier transform infrared spectroscopy. Two approaches were performed to study the effects of molar ratio of sulfonic acid to tetrazole and tetrazole content on membrane properties. In the first approach, PAN‐co ‐PSSA was blended with PAN‐co ‐PVTz at three molar ratios. The second approach focused on PAN‐co ‐PVTz‐co ‐PSSA membranes with various tetrazole contents. PAN‐co ‐PSSA membrane was also prepared. All solution‐cast membranes were hydrolytically stable, except for PAN‐co ‐PVTz‐co ‐PSSA with 71% tetrazole. Surface morphologies of blend membranes were studied using scanning electron microscopy, and no phase separation was observed. Water uptake was shown to increase with increasing tetrazole. All membranes exhibited high thermal stability (up to 250 °C) and high storage moduli. Proton conductivity was found to depend significantly on relative humidity. The influences of sulfonic acid to tetrazole ratio and tetrazole content on proton conduction were observed and discussed. A maximum proton conductivity of 7.1 × 10^?3 S/cm at 26 °C was obtained from PAN‐co ‐PSSA membrane. In addition, all tested membranes showed relatively good oxidative stability after treatment in Fenton's reagent. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45411.     

Novel composite polymer electrolyte membranes based on poly(vinyl phosphonic acid) and poly (5‐(methacrylamido)tetrazole)

Heterocyclic molecules are generally used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. Composite proton conducting membranes based on poly(vinylphosphonic acid) (PVPA) and poly(5‐(methacrylamido)tetrazole) (PMTet) were produced. The homopolymers, prepared from their corresponding monomers, were blended at several mol ratios to obtain the polymer electrolyte membranes. All samples were characterized by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), thermogravimetric analysis (TGA), differantial scanning calorimetry (DSC), cyclic voltammetry (CV), and impedance analysis. Besides, the morphology of the membranes was studied by X‐ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). FTIR spectra confirmed the formation of hydrogen bonding network between PVPA and PMTet units. TGA showed that the polymer electrolyte membranes were thermally stable up to ～210°C. CV curves demonstrated the oxidative stability of the samples in 3 V region. In anhydrous conditions, the maximum proton conductivity was determined as 0.06 Scm^?1 at 150°C for PMTetP(VPA)₄. POLYM. ENG. SCI., 55:260–269, 2015. © 2014 Society of Plastics Engineers     

Proton exchange membrane based on crosslinked sulfonated polyphosphazene containing pendent perfluorosulfonic acid groups with sulfonated poly(ether ether ketone)

A series of crosslinked membranes based on new sulfonated polyphosphazene bearing pendent perfluorosulfonic acid groups (PMFP‐g‐PS) and sulfonated poly (ether ether ketone) were prepared and evaluated as proton exchange membranes for direct methanol fuel cells (DMFCs). The structure of PMFP‐g‐PS was characterized by Fourier transform infrared spectroscopy, ¹H and ¹⁹F NMR spectra. In comparison with the pristine PMFP‐g‐PS membrane, the crosslinked membranes showed improved water uptakes and proton conductivities. The methanol permeability values of the membranes were in the range of 1.32 × 10^?7 to 3.85 × 10^?7 cm²/s, which were lower than Nafion 117 (12.1 × 10^?7 cm²/s). The selectivity of all the membranes was much higher compared with Nafion 117. Furthermore, transmission electron microscopy observation revealed that clear phase‐separated structures were well dispersed and connected to each other in the membranes. These membranes displayed high water uptakes and low swelling ratios, high proton conductivities, low methanol permeability values, good thermal, and oxidative stabilities. The results indicate that these membranes are potential candidate proton exchange membrane materials for DMFCs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43492.     

Nafion‐115/aromatic poly(etherimide) with isopropylidene groups/imidazole membranes for polymer fuel cells

Proton exchange membrane fuel cells (PEMFCs) with Pt/C gas diffusion electrodes and graphite single‐serpentine monopolar plates were constructed based on an aromatic poly(etherimide) with isopropylidene groups (PI)/imidazole (Im) and a popular Nafion‐115 matrix. The electrochemical properties of PEMFCs were tested at 25 and 60°C. The maximum power density of 171 mW/cm² and the maximum current density of 484 mA/cm² were detected for Nafion‐115/PI membrane. For both constructed PEMFCs the efficiency at 0.6 V was found about 41%. Immersion of Nafion‐115 in PI or PI/Im increased the thermal stability and mechanical properties of membranes. Thermal, mechanical properties and morphology of membranes were characterized by TGA, and AFM techniques including force spectroscopy. Interactions between the components in composite membranes were established by FT‐IR. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42436.     

Sulfonated graphene oxide‐doped proton conductive membranes based on polymer blends of highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole

Simultaneously improving the proton conductivity and mechanical properties of a polymer electrolyte membrane is a considerable challenge in commercializing proton exchange membrane fuel cells. In response, we prepared a new series of miscible polymer blends and thus the corresponding crosslinked membranes based on highly sulfonated poly(ether ether ketone) and sulfonated polybenzimidazole. The blended membranes showed more compact structures, due to the acid‐base interactions between the two constituents, and improved mechanical and morphological properties. Further efforts by doping sulfonated graphene oxide (s‐GO) forming composite membranes led to not only significantly elevated proton conductivity and electrochemical performance, but also better mechanical properties. Notably, the composite membrane with the filler content of 15 wt % exhibited a proton conductivity of 0.217 S cm^?1 at 80 °C, and its maximum power density tested by the H₂/air single PEMFC cell at room temperature reached 171 mW cm^?2, almost two and half folds compared with that of the native membrane. As a result, these polymeric membranes provided new options as proton exchange membranes for fuel‐cell applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46547.     

Hydrophilic TiO2 decorated carbon nanotubes/sulfonated poly(ether ether ketone) composite proton exchange membranes for fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is currently considered to be one of the most potential candidates of commercial perfluorinated sulfonic acid proton exchange membranes. To balance the proton conductivity and mechanical properties of SPEEK, nano TiO₂ coated carbon nanotubes (TiO₂@CNTs) were prepared using a benzyl alcohol-assisted sol-gel method and then used as a new nanofiller to modify SPEEK to prepare SPEEK/TiO₂@CNTs composite membranes. The thick insulated TiO₂ coating layer can effectively avoid the risk of electronic short-circuiting formed by CNTs, while the hydrophilicity of TiO₂ can also reduce the polar difference between CNTs and SPEEK matrix, thus promoting the homogeneous dispersion of CNTs in the composites. As a result, the composite membranes demonstrated simultaneously improved strength and proton conductivity. Incorporating 5 wt% of TiO₂@CNTs exhibited 31% growth in mechanical strength when compared with pure SPEEK. Moreover, the maximum conductivity was 0.104 S cm⁻¹ (80°C) for the composite membrane with 5 wt% of TiO₂@CNTs, which was nearly twice as high as that of SPEEK membrane (0.052 S cm⁻¹).     

Electrospinning preparation of a graphene oxide nanohybrid proton‐exchange membrane for fuel cells

Proton‐exchange membrane (PEM) is a core component of fuel cells that provides a channel for proton migration and transport. Prevailing PEMs fabricated using well‐established casting techniques have several limitations such as low proton conductivity, high fuel permeability, and poor stability. To overcome these shortcomings, this article introduces a graphene oxide (GO)‐based nanohybrid Nafion nanofiber membrane prepared using a facile electrospinning technique. On the one hand, electrospinning nanofibers provide efficient transport paths for protons, which tremendously enhance the proton conductivity. On the other hand, GO doping in PEM improves the self‐humidification, stabilities (mechanical, thermal, and chemical), and proton conductivity and reduces the fuel permeability. In this research, nanofiber membranes were obtained from Nafion solutions containing 0, 0.1, and 0.2 wt % GO via electrospinning. The morphology, structure, mechanical properties, proton conductivity, water uptake, and swelling properties of the membranes were studied. The results demonstrated that the comprehensive performance of PEM was significantly improved. The new findings may promote the wide application of PEM fuel cells. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46443.