Solution properties of hyperbranched polymers and synthetic application for amphiphilic star‐hyperbranched copolymers by grafting from hyperbranched macroinitiator

Hyperbranched polystyrenes (PS) were prepared by living radical photopolymerization of N,N‐diethyldithiocarbamoylmethylstyrene (DTCS) as an inimer under UV irradiation. Branched PS with an average chain length between branching points of four styrene units was also prepared by living radical copolymerization of DTCS with styrene. The ratio of radius of gyration to hydrodynamic radius R_G/R_H for these hyperbranched polymers was in the range 0.82–0.89 in toluene. The translational diffusion coefficient D(C) showed a constant value in the range of 0–14 × 10^?3 g ml^?1 in toluene. It was found from these dilute solution properties that hyperbranched PSs formed a unimolecular structure even in a good solvent because of their compact nature. These hyperbranched PSs exhibited large amounts of photofunctional carbamate (DC) groups on their outside surfaces. Subsequently, we derived amphiphilic star‐hyperbranched copolymers by grafting from hyperbranched macroinitiator with 1‐vinyl‐2‐pyrrolidinone. These star‐hyperbranched copolymers were soluble in water and methanol. © 2001 Society of Chemical Industry     

Synthesis of ZSM‐5 by hydrothermal method with pre‐mixing in a stirred‐tank reactor

This work proposed a synthesis route of ZSM‐5 via the hydrothermal method with premixing in a stirred tank reactor (STR). Effects of various operating conditions, including pre‐mixing time, molar ratio of SiO₂/Al₂O₃, TPAOH (organic template agents) concentration, NaCl (alkali metal cations) concentration, crystallization temperature, and crystallization reaction time, on the average particle size (PS) and particle size distribution (PSD) were investigated. It was found that the pre‐mixing time in the STR significantly affect the formation of proto‐nuclei in premixing process and crystal growth in hydrothermal reaction process, and consequently influence the PS and PSD of the prepared ZSM‐5. ZSM‐5 with good thermal stability, a PS of 380 nm, PSD of 0.17–0.9 µm, pore diameter of 2.31 nm, pore volume of 0.19 cm³ · g^?1 and specific surface area of 337.25 m² · g^?1 were obtained under the optimal conditions of a crystallization reaction time of 24 h, a crystallization temperature of 130 °C, a molar ratio of SiO₂/Al₂O₃ of 200, a TPAOH concentration of 3.5 mol · L^?1, NaCl concentration of 0.3 mol · L^?1, and a pre‐mixing time of 5 h. This work indicated that the operating conditions including premixing time have a significant effect on its PS and PSD.     

In situ cross‐linked‐PDMS/BPPO membrane for the recovery of butanol by pervaporation

In this study, an in situ crosslinked polydimethylsiloxane/brominated polyphenylene oxide (c‐PDMS/BPPO) membrane on ceramic tube has been prepared for the recovery of butanol by pervaporation. A series of BPPO with different bromide‐substituted ratio were firstly synthesized through Wohl–Ziegler reaction. BPPO and PDMS were sequentially assembled and in situ crosslinked to form the final c‐PDMS/BPPO membrane. The results of solid‐state NMR and Differential Scanning Calorimeter demonstrated that the c‐PDMS/BPPO copolymer has a crosslinking structure and the SEM result proved the coverage of ceramic tube by copolymer layer. The effects of preparation conditions including dipping time and bromide‐substituted ratio of BPPO on the membrane performance were studied. The pervaporation experiments of butanol–water mixture indicated that the c‐PDMS/BPPO membrane exhibited an acceptable flux of 220 g·m^?2·h^?1 and high separation factor of 35 towards butanol, when the bromide‐substituted ratio was 34 wt % and the dipping time was 1.33 h. Moreover, the c‐PDMS/BPPO membrane performed excellent stability in an about 200 h continuous butanol recovery, as compared to the PDMS membrane. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40004.     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Poly(2,6‐di(thiophene‐2‐yl)‐3,5bis(4‐(thiophene‐2‐yl)phenyl)dithieno [3,2‐b;2',3'‐d]thiophene)/carbon nanotube composite for capacitor applications

A novel monomer, 2,6‐di(thiophene‐2‐yl)‐3,5bis(4‐(thiophene‐2‐yl)phenyl)dithieno[3,2‐b;2',3'‐d]thiophene ( Th₄DTT) has been synthesized and used as an electro‐active material. It has been electropolymerized onto glassy carbon (GC) electrode in sodium dodecyl sulfate (SDS) solution (0.1 M) together with multi‐walled carbon nanotubes (MWCNT). A good capacitive characteristics for P(Th₄DTT)/MWCNT composite has been obtained by electrochemical impedance spectroscopy (EIS), which is, to our best knowledge, the first report on capacitor behavior of a dithienothiophene. A synergistic effect has been resolved by Nyquist, Bode‐magnitude—phase and admittance plots. Specific capacitance of the conducting polymer/MWCNT, calculated from cyclic voltammogram (CV) together with area and charge formulas, has been found to be 20.17 F g^?1. Long‐term stability of the capacitor has also been tested by CV, and the results indicated that, after 500 cycles, the specific capacitance is 87.37% of the initial capacitance. An equivalent circuit model of R_s(C₁(R₁(Q(R₂W))))(C₂R₃) has been obtained to fit the experimental and theoretical data. The double layer capacitance (C_dl) value of P(Th₄DTT)/MWCNT (4.43 mF cm^?2) has been found to be 25 times higher than P(Th₄DTT) (C_dl= 0.18 mF cm^?2). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40061.     

Film formation from polystyrene–poly(butyl acrylate‐co‐methyl methacrylate) latex blends

We have employed steady sate fluorescence (SSF) and UV‐visible (UVV) techniques to determine the film formation behavior of latex blends. Blend films were prepared from mixtures of a high‐T_g pyrene (P) labeled polystyrene (PS) latex and a low‐T_g copolymer of poly(butyl acrylate‐co‐methyl methacrylate) (BuA/MMA4). Eleven different blend films were prepared in various hard/soft latex compositions at room temperature and annealed at elevated temperatures above glass‐transition (T_g) temperature of polystyerene for 10 min. Fluorescence intensity (I_P) from P was measured after each annealing step to monitor the stages of film formation. The evolution of transparency of latex films was monitored using photon transmission intensity, I_tr. Film morphologies were examined by atomic force microscopy (AFM). A significant change occurs in both I_P and I_tr intensities at a certain critical weight fraction of hard latex (R_c = 0.3). Above R_c, two distinct film formation stages, which are named as void closure and interdiffusion processes, were seen in fluorescence data. Transparency of the films was decreased with decreasing PS content, indicating that a phase separation process occurs between PS and BuA/MMA4 phases by thermal treatment, which results in turbid films. However, below R_c, no change was observed in I_P and I_tr upon annealing, whereas transparency increased overall with increasing BuA/MMA4 ratio. We explained this result as the phase separation process between PS and BuA/MMA4 blends. These results were also confirmed by AFM pictures. Film formation stages above R_c were modeled and related activation energies were calculated. POLYM. COMPOS., 27:431–442, 2006. © 2006 Society of Plastics Engineers     

Efficiency above 6% in poly(3‐hexylthiophene):phenyl‐C‐butyric acid methyl ester photovoltaics via simultaneous addition of poly(3‐hexylthiophene) based grafted graphene nanosheets and hydrophobic block copolymers

A combination of reduced graphene oxide (rGO) nanosheets grafted with regioregular poly(3‐hexylthiophene) (P3HT) (rGO‐g‐P3HT) and P3HT‐b‐polystyrene (PS) block copolymers was utilized to modify the morphology of P3HT:[6,6]‐phenyl‐C71‐butyric acid methyl ester (PC71BM) active layers in photovoltaic devices. Efficiencies greater than 6% were acquired after a mild thermal annealing. To this end, the assembling of P3HT homopolymers and P3HT‐b‐PS block copolymers onto rGO‐g‐P3HT nanosheets was investigated, showing that the copolymers were assembled from the P3HT side onto the rGO‐g‐P3HT nanosheets. Assembling of P3HT‐b‐PS block copolymers onto the rGO‐g‐P3HT nanosheets developed the net hole and electron highways for charge transport, thereby in addition to photoluminescence quenching the charge mobility (μ_h and μ_e) values increased considerably. The best charge mobilities were acquired for the P3HT₅₀₀₀₀:PC71BM:rGO‐g‐P3HT₅₀₀₀₀:P3HT₇₀₀₀‐b‐PS₁₀₀₀ system (μ_h = 1.9 × 10^?5 cm² V^–1 s^–1 and μ_e = 0.8 × 10^?4 cm² V^–1 s^–1). Thermal annealing conducted at 120 °C also further increased the hole and electron mobilities to 9.8 × 10^?4 and 2.7 × 10^?3 cm² V^–1 s^–1, respectively. The thermal annealing acted as a driving force for better assembly of the P3HT‐b‐PS copolymers onto the rGO‐g‐P3HT nanosheets. This phenomenon improved the short circuit current density, fill factor, open circuit voltage and power conversion efficiency parameters from 11.13 mA cm^?2, 0.63 V, 62% and 4.35% to 12.98 mA cm^?2, 0.69 V, 68% and 6.09%, respectively. © 2019 Society of Chemical Industry     

Polystyrene composites of single‐walled carbon nanotubes‐graft‐polystyrene

Single‐walled carbon nanotubes (SWCNTs) dispersed in N‐methylpyrrolidone (NMP) were functionalized by addition of polystyryl radicals from 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐ended polystyrene (SWCNT‐g‐PS). The amount of polystyrene grafted to the nanotubes was in the range 20‐25 wt% irrespective of polystyrene number‐average molecular weight ranging from 2270 to 49 500 g mol^?1. In Raman spectra the ratios of D‐band to G‐band intensity were similar for all of the polystyrene‐grafted samples and for the starting SWCNTs. Numerous near‐infrared electronic transitions of the SWCNTs were retained after polymer grafting. Transmission electron microscopy images showed bundles of SWCNT‐g‐PS of various diameters with some of the polystyrene clumped on the bundle surfaces. Composites of SWCNT‐g‐PS in a commercial‐grade polystyrene were prepared by precipitation of mixtures of the components from NMP into water, i.e. the coagulation method of preparation. Electrical conductivities of the composites were about 10^?15 S cm^?1 and showed no percolation threshold with increasing SWCNT content. The glass transition temperature (T_g) of the composites increased at low filler loadings and remained constant with further nanotube addition irrespective of the length and number of grafted polystyrene chains. The change of heat capacity (ΔC_p) at T_g decreased with increasing amount of SWCNT‐g‐PS of 2850 g mol^?1, but ΔC_p changed very little with the amount of SWCNT‐g‐PS of higher molecular weight. The expected monotonic decrease in ΔC_p coupled with the plateau behavior of T_g suggests there is a limit to the amount that T_g of the matrix polymer can increase with increasing amount of nanotube filler. Copyright © 2012 Society of Chemical Industry     

Porous palygorskite‐polythiophene conductive composites for acrylic coatings

Modified palygorskite‐polythiophene (MPA‐PTh) composites were prepared by chemical oxidative polymerization of palygorskite (PA) nucleartor with thiophene (Th) after the surface modification with γ‐(2,3‐epoxypropoxy) propytrimethoxysilane (KH‐560). The MPA‐PTh composites were doped in iodine vapor to create the porous palygorskite‐polythiophene (PMPA‐PTh) conductive composites. Fourier transform infrared spectra (FTIR), X‐ray photoelectron spectroscopy (XPS), X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂ adsorption–desorption isotherms using the Brunauer–Emmett–Teller method (BET) and electrochemical impedance spectrum (EIS) techniques were applied to characterize the modified PA and the prepared composites. According to FTIR and XPS, the KH‐560 was bound to the PA surface and the iodine ion (I₃^? and I₅^?) entered the PTh molecular chains. XRD, SEM, TEM, BET, and EIS analysis confirmed that the doping of iodine not only transform the core–shell MPA‐PTh into the PMPA‐PTh but also improve the electrical conductivity of composites. The PMPA‐PTh composites were fabricated that yield a volume resistivity of ～2.44 × 10² Ω cm and a internal resistances of ～100 Ω, and their BET surface area, BJH (Barrett–Joiner–Halenda) average pore size and BJH cumulative pore volume were improved in comparison with those of the MPA‐PTh composites. SEM images showed that the PMPA‐PTh composites could form consecutive space network and the PMPA‐PTh composites acrylic coating films had advisable conductivity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Studies of solvent effect on the conductivity of 2‐mercaptopyridine‐doped solid polymer blend electrolytes and its application in dye‐sensitized solar cells

Solvents and electrolytes play an important role in the fabrication of dye‐sensitized solar cells (DSSCs). We have studied the poly(ethylene oxide)‐poly(methyl methacrylate)‐KI‐I₂ (PEO‐PMMA‐KI‐I₂) polymer blend electrolytes prepared with different wt % of the 2‐mercaptopyridine by solution casting method. The polymer electrolyte films were characterized by the FTIR, X‐ray diffraction, electrochemical impedance and dielectric studies. FTIR spectra revealed complex formation between the PEO‐PMMA‐KI‐I₂ and 2‐mercaptopyrindine. Ionic conductivity data revealed that 30% 2‐mercaptopyridine‐doped PEO‐PMMA‐KI‐I₂ electrolyte can show higher conductivity (1.55 × 10^?5 S cm^?1) than the other compositions (20, 40, and 50%). The effect of solvent on the conductivity and dielectric of solid polymer electrolytes was studied for the best composition (30% 2‐mercaptopyridine‐doped PEO‐PMMA‐KI‐I₂) electrolyte using various organic solvents such as acetonitrile, N,N‐dimethylformamide, 2‐butanone, chlorobenzene, dimethylsulfoxide, and isopropanol. We found that ac‐conductivity and dielectric constant are higher for the polymer electrolytes processed from N,N‐dimethylformamide. This observation revealed that the conductivity of the solid polymer electrolytes is dependent on the solvent used for processing and the dielectric constant of the film. The photo‐conversion efficiency of dye‐sensitized solar cells fabricated using the optimized polymer electrolytes was 3.0% under an illumination of 100 mW cm^?2. The study suggests that N,N‐dimethylformamide is a good solvent for the polymer electrolyte processing due to higher ac‐conductivity beneficial for the electrochemical device applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42489.     

Microporous gel electrolyte for quasi‐solid‐state dye‐sensitized solar cell

The extension of electrocatalytic reaction of I^?/I₃^? from counter electrode/gel electrolyte interface to gel electrolyte can significantly enhance the redox kinetics and therefore conversion efficiency of dye‐sensitized solar cells. Microporous gel electrolyte from polypyrrole integrated poly(hydroxyethyl methacrylate/cetytrimethylammonium bromide) [PPy‐integrated poly (HEMA/CTAB)] is successfully synthesized by in‐situ polymerization of pyrrole monomers in three‐dimensional framework of porous poly(HEMA/CTAB) matrix. An ionic conductivity of 12.72 mS cm^?1 and activation energy of 8.65 kJ mol^?1 are obtained from PPy‐integrated poly(HEMA/CTAB) gel electrolyte. Tafel polarization and electrochemical impedance spectroscopy are employed to characterize the electrocatalytic behaviors of the gel electrolytes. The resultant quasi‐solid‐state dye‐sensitized solar cell shows a light‐to‐electrical conversion efficiency of 6.68%. POLYM. ENG. SCI., 54:2531–2535, 2014. © 2013 Society of Plastics Engineers     

Syntheses and adsorption properties for Hg2+ of chelating resin of crosslinked polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole

A novel chelating resin with functional group containing S and N atoms was prepared using chloromethylated polystyrene and 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT) as materials. Its structure was characterized by infrared spectra and elementary analysis. The results showed that the content of the functional group was 2.07 mmol BMT g^?1 resin, 47% of which were in the form of monosubstitution (PS‐BMT‐1) and 53% in the form of double substitution (PS‐BMT‐2). The adsorption for mercury ion was investigated. The adsorption dynamics showed that the adsorption was controlled by liquid film diffusion. Increasing the temperature was beneficial to adsorption. The Langmuir model was much better than the Freundlich model to describe the isothermal process. The adsorption activation energy (E_a), ΔG, ΔH, and ΔS values calculated were 18.56 kJ·mol^?1, ‐5.99 kJ·mol^?1, 16.38 kJ·mol^?1, and 37.36, J·mol^?1·K^?1, respectively. The chelating resin could be easily regenerated by 2% thiourea in 0.1 mol·L^?1 HCl with higher effectiveness. Five adsorption–desorption cycles demonstrated that this resin was suitable for repeated use without considerable change in adsorption capacity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1646–1652, 2004     

Synthesis of poly(methylphenylsiloxane) rich in syndiotacticity by Rh‐catalysed stereoselective cross‐dehydrocoupling polymerization of optically active 1,3‐dimethyl‐1,3‐diphenyldisiloxane derivatives

Cross‐dehydrocoupling reactions of (R)‐methyl(1‐naphthyl)phenylsilane (>99%ee) with (S)‐methyl(1‐naphthyl)phenylsilanol (>99% ee) proceeded with 82–99% retention of configuration of chiral silicon centres in the presence of various Rh‐catalysts. Cross‐dehydrocoupling polymerization of 1,3‐dimethyl‐1,3‐diphenyl‐1,3‐disiloxanediol with 1,3‐dihydro‐1,3‐dimethyl‐1,3‐diphenyl‐1,3‐disiloxane gave poly(methylphenylsiloxane) of moderate molecular weight in toluene at 60 °C in the presence of [RhCl(cod)]₂ (5.0 mol%) and triethylamine (1.0 equivalent). Assignment of the triad signals of the resulting polymer was made by ¹H NMR spectroscopy of the methyl proton (I = 0.04, H = 0.09 and S = 0.14 ppm) and ¹³C NMR spectroscopy of the ipso carbon of the phenyl group (S = 136.7, H = 136.9, and I = 137.1 ppm). Although the reaction of optically pure (S,S)‐1,3‐dimethyl‐1,3‐diphenyl‐1,3‐disiloxanediol with 1,3‐dihydro‐1,3‐dimethyl‐1,3‐diphenyl‐1,3‐disiloxane [(S,S):(S,R):(R,R)] = 84:16:0] gave a poly(methylphenylsiloxane) of rather low molecular weight, its triad tacticity was found to be rich in syndiotacticity (S:H:I = 60:32:8) by ¹³C NMR spectroscopy. © 2001 Society of Chemical Industry     

High‐performing dye‐sensitized solar cells based on reduced graphene oxide/PEDOT‐PSS counter electrodes with sulfuric acid post‐treatment

Four kinds of counter electrodes are prepared with polystyrene‐sulfonate doped poly(3,4‐ethylenedioxythiophene) (PEDOT‐PSS) as basic material, reduced graphene oxide (rGO) sheets as additives and H₂SO₄ as treating agent. The cyclic voltammetry and Tafel polarization are measured to evaluate catalytic activity of these counter electrodes for /I^? redox couple. It is found that H₂SO₄ treated rGO and PEDOT‐PSS hybrid counter electrode (S/rGO/PEDOT‐PSS counter electrode) has the highest catalytic activity among these counter electrodes. Power conversion efficiency of the dye‐sensitized solar cell with S/rGO/PEDOT‐PSS counter electrode can attain to 7.065%, distinctly higher than that of the cells with the other three ones, owing to the great enhanced fill factor and short‐circuit current density. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42648.     

Amino‐functional electrospun nanofibrous membrane for detecting nitroaromatic compounds

A novel amino‐functionalized polystyrene copolymer (PS‐NH₂) was designed and synthesized with styrene and 4‐vinylbenzyl amine. Additionally, an amino modified glass (G‐NH₂) was obtained as a carrier. (PS‐NH₂/pyrene)/G‐NH₂ fluorescent nanofibrous membrane [named (PS‐NH₂/pyrene)/G‐NH₂] was designed and prepared via electrospinning technique to detect representative saturated nitroaromatic (NAC) explosive vapor. The (PS‐NH₂/pyrene)/G‐NH₂ showed highly fluorescence stability in ambient condition and further displayed a high quenching efficiency of 70.9% toward trinitrotoluene (TNT) vapor (～10 ppb) with an exposure time of 150 s at room temperature. The abundance of amino groups could effectively adsorb NACs and the binding of electron‐deficient NACs to the amino groups on the (PS‐NH₂/pyrene)/G‐NH₂ surface led to the formation of charge‐transfer complexes. The quenching constant (K_SV) to TNT was obtained to be 1.07 × 10¹¹ mL/g in gaseous phase with a limit of detection up to 2.76 × 10^?13g/mL. Importantly, the (PS‐NH₂/pyrene)/G‐NH₂ showed notable selectivity toward TNT and 2,4‐dinitrotoluene vapors. Straightforwardly, the colorimetric sensing performance can be visualized by naked eye with a color change for detecting of different vapor phase NACs explosives. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46708     

Segregation of resin‐bound peptides during solid‐phase synthesis

To compare the segregation ability of 1,4‐butanediol dimethacrylate‐crosslinked polystyrene (BDDMA‐PS) and divinylbenzene‐crosslinked polystyrene (DVB‐PS), a set of difficult sequence peptides characterized by high‐arithmetic‐average β‐sheet stabilizing potential (SP_β) and low‐stepwise arithmetic average random coil conformational parameter (P_c*) were synthesized on both supports (～ 2 mmol Cl g^?1) under identical conditions. The yield and purity of the peptides obtained from BDDMS‐PS resin were higher than from DVB‐PS resin. The synthetic efficiency of the new support was found to be its ability to suppress the aggregation of growing peptide chains by β‐sheet formation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1717–1723, 2002     

Ammonium fumarate production by free or immobilised Rhizopus arrhizus in bench‐ and laboratory‐scale bioreactors

Ammonium fumarate production from glucose‐based media by Rhizopus arrhizus NRRL 1526 with mycelial growth controlled by phosphorus limitation exhibited mixed‐growth‐associated product formation kinetics, with growth‐associated production related to secondary mycelial growth only. The contribution of the primary mycelial growth phase was minimised by resorting to prolonged batch production using free mycelia under intermittent glucose feeding or repeated batch production using immobilised mycelia. The metabolic activity of free or immobilised mycelia was limited by fumarate accumulation or by oxygen diffusion phenomena, respectively. For batch cultures in a 15 dm³ stirred bioreactor the peripheral impeller speed (v_I) was increased from 1.88 to 3.3 m s^?1, and the fumarate yield coefficient on glucose increased from 0.25 ± 0.01 to 0.42 ± 0.02 g g^?1, while the malate yield coefficient on fumarate (Y_M/F) reduced from 0.46 ± 0.01 to 0.14 ± 0.01 g g^?1. With a net increase in the fumarate‐to‐malate ratio from 2 to 6.5, a v_I value of 3.3 m s^?1 gave the best fermentation performance and provided a basis for further scale‐up studies. © 2002 Society of Chemical Industry     

Particle size effect on the film‐forming process of PS/PBA composite latexes

In this work, the effect of hard particle size and blend ratio on the film formation behavior of hard polystyrene (PS) and soft poly(n‐butyl acrylate) (PBA) latex blends was studied by means of steady‐state fluorescence and UV–visible techniques in conjunction with atomic force microscopy. Three different sets of latexes were synthesized: PBA latex (diameter 97 nm), pyrene (P)‐labeled large PS (LgPS; diameter 900 nm), and small PS (SmPS; diameter 320 nm). Two different series of latex blends (LgPS/PBA and SmPS/PBA) were prepared with varying blend composition at room temperature separately. Films were then annealed at elevated temperatures above glass transition (T_g) temperature of PS. Fluorescence intensity (I_P) from P and photon transmission intensity (I_tr) were measured after each annealing step to monitor the stages of film formation. The results showed that a significant change occurred in I_P and I_tr at a certain critical weight fraction (R_c) of PBA. Below R_c, two distinct film formation stages, which are named as void closure and interdiffusion, were seen. However, at PBA concentrations nearer to or above R_c, no film formation can be achieved. Comparing to the LgPS/PBA, the sintering process of SmPS/PBA particles occurred at much lower temperatures. Film formation stages for R < R_c were modeled, and related activation energies were calculated. Void closure (ΔH) and interdiffusion (ΔE) activation energies for SmPS/PBA were also found smaller in comparing with LgPS/PBA series. However, ΔH and ΔE values were not changed much with the blend composition for both series. POLYM. COMPOS., 31:1637–1652, 2010. © 2009 Society of Plastics Engineers     

A redox‐mediator‐doped gel polymer electrolyte applied in quasi‐solid‐state supercapacitors

Methylene blue (MB) redox mediator was introduced into polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blend host to prepare a gel polymer electrolyte (PVA‐PVP‐H₂SO₄‐MB) for a quasi‐solid‐state supercapacitor. The electrochemical properties of the supercapacitor with the prepared gel polymer electrolyte were evaluated by cyclic voltammetry, galvanostatic charge–discharge, electrochemical impedance spectroscopy, and self‐discharge measurements. With the addition of MB mediator, the ionic conductivity of gel polymer electrolyte increased by 56% up to 36.3 mS·cm^?1, and the series resistance reduced, because of the more efficient ionic conduction and higher charge transfer rate, respectively. The electrode specific capacitance of the supercapacitor with PVA‐PVP‐H₂SO₄‐MB electrolyte is 328 F·g^?1, increasing by 164% compared to that of MB‐undoped system at the same current density of 1 A·g^?1. Meanwhile, the energy density of the supercapacitor increases from 3.2 to 10.3 Wh·kg^?1. The quasi‐solid‐state supercapacitor showed excellent cyclability over 2000 charge/discharge cycles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39784.     

Enhancement of mechanical and optical performance of commercial polystyrenes by blending with siloxane‐based copolymers

Well‐defined poly(styrene‐block ‐dimethylsiloxane) copolymers (PS‐b ‐PDMS) with low polydispersity index (M_w /M_n ) and different compositions were synthesized by sequential anionic polymerization of styrene (S) and hexamethyl(ciclotrisiloxane) (D₃) monomers. Synthesized PS‐b ‐PDMS copolymers were characterized by ¹H‐nuclear magnetic resonance, size exclusion chromatography, Fourier transform infrared spectroscopy, and transmission electron microscopy. The physicochemical characterization determined that block copolymers have molar mass values close to ～135,000 g mol^?1, narrow M_w /M_n < 1.3, and chemical composition ranging from low to intermediate PDMS content. Blends of these copolymers with a commercial polystyrene (PS) were obtained by melt mixing and subsequently injection. Films obtained were flexible, and showed lower transparency than the original PS matrix. On the other hand, a 10 wt % incorporation of PS‐b ‐PDMS copolymers leads to better mechanical performance by enhancing elongation at break (～8.8 times higher) and opacity values (～18 times higher). In addition, UV–Vis barrier capacity of the resulting blends is also increased (up to 400% higher). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45122.