Influence of Multiwalled Carbon Nanotubes on Mechanical,Thermal and Electrical Behavior of Polybenzoxazine-Epoxy Nanocomposites

Multiwalled carbon nanotubes (MWCNT)-reinforced polybenzoxazine-epoxy nanocomposites were prepared via the solvent method and were investigated for their thermal, thermo-mechanical, mechanical, electrical and morphological properties. Epoxy resin (DGEBA) was modified with 5, 10 and 15 wt.% of benzoxazines using 4,4′-diaminodiphenylmethane as a curing agent at appropriate conditions. Epoxy and benzoxazines-modified epoxy systems were further reinforced with 0.25, 0.50 and 0.75 wt.% of surface-modified MWCNT. MWCNT-reinforced polybenzoxazine-epoxy nanocomposites exhibited better thermal, mechanical and dielectric properties. Dispersion of MWCNT in benzoxazine-epoxy resins and nanostructure of the composites was confirmed by transmission electron microscopy analysis.     

Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

Influences of different gravity environments on the curing process and cured products of carbon‐nanotube‐reinforced epoxy composites

The influences of different gravity environments on the curing process and the cured products of carbon‐nanotube‐reinforced epoxy composites were investigated in this study. Different gravity environments were simulated with a superconducting magnet on the basis of which resin matrix composites with different amino‐functionalized multiwalled carbon nanotube (NH₂‐MWCNT) concentrations of 0.1, 0.3, 0.5, and 1 wt % were tested. Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, thermomechanical analysis (TMA), thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, and three‐point bending tests were used to analyze the characteristics of different curing processes and cured products. From the results, we observed that the curing rate of the epoxy composites was influenced by different gravity values, and there was anisotropy in the NH₂‐MWCNT‐reinforced epoxy composites cured in the simulated microgravity environment. More effects of gravity on the curing process and cured products could be obtained through detailed experiments and discussion; this is important and fundamental for improving and enhancing the properties of composite materials used in different gravity environments. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41413.     

Relationship between viscoelastic properties and gelation in the epoxy/phenol‐novolac blend system with N‐benzylpyrazinium salt as a latent thermal catalyst

A study of viscoelastic properties and gelation in epoxy/phenol‐novolac blend system initiated with 1 wt % of N‐benzylpyrazinium hexafluoroantimonate (BPH) as a latent cationic thermal initiator was performed by analysis of rheological properties using a rheometer. Latent behavior was investigated by measuring the conversion as a function of curing temperature using traditional curing agents, such as ethylene diamine (EDA) and nadic methyl anhydride (NMA) in comparison to BPH. In the relationship between viscoelastic properties and gelation of epoxy/phenol‐novolac blend system, the time of modulus crossover was dependent on high frequency and cure temperature. The activation energy (E_c) for crosslinking from rheometric analysis increased within the composition range of 20–40 wt % phenol‐novolac resin. The 40 wt % phenol‐novolac (N40) to epoxy resin showed the highest value in the blend system, due to the three‐dimensional crosslinking that can take place between hydroxyl groups within the phenol resin or epoxides within the epoxy resin involving polyaddition of the initiator with BPH. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2299–2308, 2001     

The effects of polyamic acid on curing behavior,thermal stability,and mechanical properties of epoxy/DDS system

A thermoplastic modification method was studied for the purpose of improving the toughness and heat resistance and decreasing the curing temperature of the cured epoxy/4, 4′‐diaminodiphenyl sulfone resin system. A polyimide precursor‐polyamic acid (PAA) was used as the modifier which can react with epoxy. The effects of PAA on curing temperature, thermal stability and mechanical properties were investigated. The initial curing temperature (T_i) of the resin with 5 wt % PAA decreased about 50°C. The onset temperature of thermal decomposition and 10 wt %‐weight‐loss temperature for the resin system containing 2 wt % PAA increased about 60°C and 15°C respectively. Besides, the value of impact toughness and plain strain fracture toughness for the modified epoxy resin increased ～ 190% and 55%, respectively. Those changes were attributed to the outstanding thermal and mechanical properties of polyimide, and more importantly to formation of semi‐interpenetrating polymer networks composed by the epoxy network and linear PAA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Properties of networks obtained by internal plasticization of epoxy resin with aromatic and aliphatic glycidyl compounds

In order to improve the fracture properties of p, p′-diaminodiphenylmethane-cured epoxy resin, various kinds of aromatic and aliphatic glycidyl compounds were investigated as a modifier at an amount of 30 wt %. Several compounds promoted the fracture toughness. In any glycidyl compounds, however, heat resistance was decreased by the modification. The dynamic mechanical properties of the modified epoxy resins were measured. The crosslinking density ρ was calculated from the theory of rubber elasticity, and the mechanical properties of the resins were discussed in regard to the crosslinking density. Tensile strength was scarcely affected by the crosslinking density. Elongation at break and Izod impact strength increased remarkably with decrease in crosslinking density. The fracture toughness K_Ic- increased with decrease in crosslinking density except at small ρ.     

Preparation and thermal,electrical, and morphological properties of multiwalled carbon nanotubeand epoxy composites

Multiwalled carbon nanotube (MWCNT)/epoxy composites are prepared, and the characteristics and morphological properties are studied. Scanning electron microscopy microphotographs show that MWCNTs are dispersed on the nanoscale in the epoxy resin. The glass‐transition temperature (T_g) of MWCNT/epoxy composites is dramatically increased with the addition of 0.5 wt % MWCNT. The T_g increases from 167°C for neat epoxy to 189°C for 0.5 wt % CNT/epoxy. The surface resistivity and bulk resistivity are decreased when MWCNT is added to the epoxy resins. The surface resistivity of CNT/epoxy composites decreases from 4.92 × 10¹² Ω for neat epoxy to 3.03 × 10⁹ Ω for 1 wt % MWCNT/epoxy. The bulk resistivity decreases from 8.21 × 10¹⁶ Ω cm for neat epoxy to 6.72 × 10⁸ Ω cm for 1 wt % MWCNT/epoxy. The dielectric constant increases from 3.5 for neat epoxy to 5.5 for 1 wt % MWCNT/epoxy. However, the coefficient of thermal expansion is not affected when the MWCNT content is less than 0.5 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1272–1278, 2007     

Hybridizing MWCNT with nano metal oxides and TiO2 in epoxy composites: Influence on mechanical and thermal performances

In this study, the effects of multi‐walled carbon nanotubes (MWCNT), and its hybrids with iron oxide (Fe₂O₃) and copper oxide (CuO) nanoparticles on mechanical characteristics and thermal properties of epoxy binder was evaluated. Furthermore, simultaneous effects of using MWCNT with TiO₂ as pigment and CaCO₃ as filler for epoxy composites were determined. To investigate effects of nano‐ and micro‐particles on epoxy matrix, the samples were evaluated by TGA and DTA. It was found that the hybrid of MWCNT with nano metal oxides caused considerable increment in the tensile and flexural properties of epoxy samples in comparison to the single MWCNT containing samples at the same filler contents. Significant improvement in the thermal conductivity of epoxy samples was obtained by using TiO₂ pigment along with MWCNT. The TiO₂ pigment also caused considerable improvement in mechanical properties of the epoxy matrix and the MWCNT containing nanocomposite. The best mechanical and thermal properties of epoxy nanocomposites were obtained at 1.5 wt % of MWCNT and 7 wt % of TiO₂ that it should be attributed to particle network forming of the particles which cause better nano/micro dispersion and properties. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43834.     

Study on synthesis of polyurethane‐epoxy composite emulsion

The stable polyurethane‐epoxy composite emulsion with the epoxy‐amine oligomer (DEA‐EP) and the epoxy resin oligomer has been prepared by step‐growth polymerization and controlled crosslinking technique. The emulsion forming transparent films can be cured at room temperature with trimethylolpropane tris (1‐ethyleneimine) propionate (TMPTA‐AZ). The DEA‐EP structure and its reaction with urethane prepolymers were proved by Fourier transform infrared spectra (FTIR). The studies on particle size, the particle size distribution, viscosity, and the films' transmittance (Tr) indicated that both trimethylol propane (TMP) and DEA‐EP contributed to improving the resin blends' compatibility and reducing the viscosity. The epoxy resin content can increase up to 20.0 wt % (based on the total content of the polyurethane and epoxy resin) and the emulsion was still stable. The data from the tensile test experiments showed that with the epoxy content increasing, the tensile strength (σ_b) and Young's modulus were proportionately raised, but the elongation at break (ε_b) decreased. Tensile tests also revealed that introducing TMPTA‐AZ as an outside‐crosslinker can increase the tensile strength. By adding 0.3 wt % of TMPTA‐AZ, the ε_b reduced from 429% to 371% and the σ_b increased from 4.4 to 13.73 MPa; by adding 1.8 wt % of TMPTA‐AZ, ε_b of the film was 67% of ε_b of the film with 0.3 wt % of TMPTA‐AZ, but its σ_b was 24.77 MPa and 180% of σ_b of the film with 0.3 wt % of TMPTA‐AZ. The cured films possessed excellent water and toluene resistance: water uptake (48 h, 3.1%; degree of curing: 70%), toluene uptake (210 h, 8%. degree of curing: 70%). Better properties of the composite emulsion will confer it as a potential application in low volatile industrial coatings. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

High-toughness,environment-friendly solid epoxy resins: Preparation,mechanical performance,curing behavior,and thermal properties

The development of a facile and efficient approach to prepare high-toughness epoxy resin is vital but has remained an enormous challenge. Herein, we have developed a high-performance environment-friendly solid epoxy resin modified with epoxidized hydroxyl-terminated polybutadiene (EHTPB) via one-step melt blending. The characterization, mechanical performance, curing behavior, and thermal properties of EHTPB-modified epoxy resin were investigated. EHTPB-modified epoxy resin exhibited excellent toughness with a 100% increase in elongation at break of tensile than that of neat epoxy resin. The transfer stress and dissipated energy in the rubber phase were predominant mechanisms of toughening. The toughening effect of EHTPB on solid epoxy resin was better than that of some of the previously reported liquid epoxy resins. Meanwhile, at 10 wt % of EHTPB loading, the EHTPB-modified epoxy resin displayed high strength and 22 and 101% improvement of flexural strength and impact strength, respectively. Moreover, at 10 wt % of EHTPB loading, the activation energy of EHTPB-modified epoxy resin for curing reaction decreased from 73.89 to 65.12 kJ·mol⁻¹, which is beneficial for the curing reaction. Furthermore, EHTPB-modified epoxy resin had a good thermal stability and the initial degradation temperature increased from 249 to 313 °C at 10 wt % of EHTPB loading. This work provides a simple-preparation and highly efficient and large-scale approach for the production of high-toughness environment-friendly solid epoxy resins. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48596.     

Poly(ether imide)‐modified benzoxazine blends: Influences of phase separation and hydrogen bonding interactions on the curing reaction

Polymer blends of polybenzoxazine (PBZ)/poly(ether imide) (PEI) were prepared by the in situ curing reaction of benzoxazine (BZ) resin in the presence of PEI. Phase separation induced by the polymerization of BZ resin was observed. The rheological behaviors, morphologies, and their evolution process of BZ/PEI blends were investigated by rheometer and scanning electron microscope. Phase separation that took place at the early stage of the curing reaction effectively reduced the dilution effect of PEI. Fourier transform infrared (FTIR) results suggested that hydrogen bonds between PBZ and PEI existed during the whole curing process, although weakened with phase separation. The decrease of isoconversion activation energy indicated that the polymerization of BZ resin was facilitated in the presence of such kind of hydrogen‐bonding interactions. By changing the weight fraction of PEI, extensive phase separation was obtained in PBZ blends with 5 and 20 wt % of PEI, in which systems, the crosslinking density and glass transition temperature (T_g) of PBZ‐rich phase were greatly improved compared to this single PBZ system. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Direct functionalization with 3,5‐substituted benzoic acids of multiwalled carbon nanotube/epoxy composites

Directly functionalized multiwalled carbon nanotubes (MWCNTs) with benzene‐1,3,5‐tricarboxylic acid (BTC) and 3,5‐diaminobenzoic acid (DAB) were successfully accomplished with less structural damage as confirmed by XPS and FT‐Raman results. Their dispersibility and thermal stability were achieved after the functionalization. The functional groups on MWCNT surfaces can accelerate the curing reaction of epoxy composites remarkable inducing rather low exothermic peak temperature (T_p) and exothermic heat of reaction (ΔH). The values of activation energy (E_a) obtained from Kissinger and Ozawa methods obviously decreased with the introduction of MWCNTs, especially DAB‐MWCNTs. The dynamic mechanical properties notably enhanced with the incorporation of unmodified and functionalized MWCNTs. The crosslink density (ρ) increased and free volume fraction (f_g) decreased, resulting in dramatic increase of glass transition temperatures (T_g) and decrease of coefficient of thermal expansion. Additionally, epoxy composites exhibited low dielectric constant close to that of neat epoxy resin. From these remarkable properties, MWCNT/epoxy composites can be considered as a good candidate for high performance insulation materials. POLYM. ENG. SCI., 53:2194–2204, 2013. © 2013 Society of Plastics Engineers     

Epoxy resin containing the poly(sily ether): Preparation,morphology, and mechanical properties

The poly(sily ether) with pendant chloromethyl groups (PSE) was synthesized by the polyaddition of dichloromethylsilane (DCM) and diglycidylether of bisphenol A (DGEBA) with tetrabutylammonium chloride (TBAC) as a catalyst. This polymer was miscible with diglycidyl ether of bisphenol A (DGEBA), the precursor of epoxy resin. The miscibility is considered to be due mainly to entropy contribution because the molecular weight of DGEBA is quite low. The blends of epoxy resin with PSE were prepared through in situ curing reaction of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐diaminodiphenylmethane (DDM) in the presence of PSE. The DDM‐cured epoxy resin/PSE blends with PSE content up to 40 wt % were obtained. The reaction started from the initial homogeneous ternary mixture of DGEBA/DDM/PSE. With curing proceeding, phase separation induced by polymerization occurred. PSE was immiscible with the 4,4′‐diaminodiphenylmethane‐cured epoxy resin (ER) because the blends exhibited two separate glass transition temperatures (T_gs) as revealed by the means of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). SEM showed that all the ER/PSE blends are heterogeneous. Depending on blend composition, the blends can display PSE‐ or epoxy‐dispersed morphologies, respectively. The mechanical test showed that the DDM‐cured ER/PSE blend containing 25 wt % PSE displayed a substantial improvement in Izod impact strength, i.e., epoxy resin was significantly toughened. The improvement in impact toughness corresponded to the formation of PSE‐dispersed phase structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 505–512, 2003     

Addition‐cure‐type phenolic resin based on alder‐ene reaction: Synthesis and laminate composite properties

A maleimide‐functional phenolic resin was reactively blended with an allyl‐functional novolac in varying proportions. The two polymers were coreacted by an addition mechanism through Alder‐ene and Wagner–Jauregg reactions to form a crosslinked network system. The cure characterization was done by differential scanning calorimetry and dynamic mechanical analysis. The system underwent a multistep curing process over a temperature range of 110–270°C. Although the cure profiles were independent of the composition, the presence of maleimide led to a reduced isothermal gel time of the blend. Increasing the allylphenol content decreased the crosslinking in the cured matrix, leading to enhanced toughness and improved resin‐dominant mechanical properties of the resultant silica laminate composites. Changing the reinforcement from silica to glass resulted in further amelioration of the resin‐reinforcement interaction, but the resin‐dominant properties of the composite remained unaltered. Increasing the maleimide content resulted in enhanced thermal stability. Integrating both the reactive groups in a single polymer and its curing led to enhanced thermal stability and T_g, but to decreased mechanical properties of the laminate composites. This can be attributed to a brittle matrix resulting from enhanced crosslinking facilitated by interaction of the reactive groups located on the polymer of an identical backbone structure. The cured polymers showed a T_g in the range of 170–190°C. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 737–749, 2001     

Catalytic effect of 2,2′‐diallyl bisphenol A on thermal curing of cyanate esters

Cyanate esters are a class of thermal resistant polymers widely used as thermal resistant and electrical insulating materials for electric devices and structural composite applications. In this article, the effect of 2,2′‐diallyl bisphenol A (DBA) on catalyzing the thermal curing of cyanate ester resins was studied. The curing behavior, thermal resistance, and thermal mechanical properties of these DBA catalyzed cyanate ester resins were characterized. The results show that DBA is especially suitable for catalyzing the polymerization of the novolac cyanate ester resin (HF‐5), as it acts as both the curing catalyst through depressing the exothermic peak temperature (T_exo) by nearly 100°C and the toughening agent of the novolac cyanate ester resin by slightly reducing the elastic modulus at the glassy state. The thermogravimetric analysis and dynamic mechanical thermal analysis show that the 5 wt % DBA‐catalyzed novolac cyanate ester resin exhibits good thermal resistance with T_d⁵ of 410°C and the char yield at 900°C of 58% and can retain its mechanical strength up to 250°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1775–1786, 2006     

Nano‐sio2‐reinforced ultraviolet‐curing materials for three‐dimensional printing

As an additive manufacturing technology, ultraviolet (UV)‐curing three‐dimensional printing, which requires the use of a photocurable resin, is increasingly being used to produce customized end‐user parts of many complex shapes. In this study, to improve the strength and ductility of printing materials, nano‐SiO₂‐reinforced photocurable resins were prepared by a planetary ball mill; then, the morphology, photochemistry, thermal property, and mechanical properties of the nanocomposites were investigated and characterized. Transmission electron microscopy analysis indicated that the modified nano‐SiO₂ was well dispersed in the photocurable resin. The glass‐transition temperature increased from 67.2°C for the unfilled resin to 71.7 and 80.1°C for nanocomposites with nano‐SiO₂ contents of 0.3 and 0.7 wt %, respectively. The tensile strength and impact strength were increased by 46.7 and 165.3% for nanocomposites with 0.3 wt % nano‐SiO₂. The flexural modulus of the nanocomposites increased from 1.7 to 8.0 GPa when 0.7 wt % nano‐SiO₂ was added to the photocurable resin; this appeared to originate from the relatively high level of dispersion and the intimate combination of the nano‐SiO₂ with the matrix. The investigation of the physical and chemical properties of such UV‐curing materials showed that the low filler concentration (<1 wt %) of nano‐SiO₂ did not affect the processability of the nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42307.     

Blends of epoxy resin with amine‐terminated polyoxypropylene elastomer: Morphology and properties

A liquid diglycidyl ether of bisphenol A (DGEBA) epoxy resin is blended in various proportions with amine‐terminated polyoxypropylene (POPTA) and cured using an aliphatic diamine hardener. The degree of crosslinking is varied by altering the ratio of diamine to epoxy molecules in the blend. The mixture undergoes almost complete phase separation during cure, forming spherical elastomer particles at POPTA concentrations up to 20 wt %, and a more co‐continuous morphology at 25 wt %. In particulate blends, the highest toughness is achieved with nonstoichiometric amine‐to‐epoxy ratios, which produce low degrees of crosslinking in the resin phase. In these blends, the correlation between G_IC and plateau modulus (above the resin T_g), over a wide range of amine‐to‐epoxy ratios, confirms the importance of resin ductility in determining the fracture resistance of rubber‐modified thermosets. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 427–434, 1999     

Reactive blends of epoxy resin (DGEBA) crosslinked by anionically polymerized polycaprolactam: Process of epoxy cure and kinetics of decomposition

The curing reactions, kinetics, morphology, and thermal stability of the reactive blends of diglycidyl ether of bisphenol‐A (DGEBA) and polycaprolactam were studied by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric analysis. DSC studies showed that the heat of reaction (ΔH) increased when the DGEBA content was increased from 50 to 80 wt % and increased drastically above 70 wt % DGEBA content because of an increase in the extent of crosslinking. The activation energy and pre‐exponential factor of cure reactions increased drastically with an increase in the DGEBA content above 70 wt % because of a drastic increase in crosslink density. The extent of curing reaction of polycaprolactam with DGEBA is dependent on the blend composition. The nucleophilic attack on oxirane ring by amide nitrogen of polycaprolactam is a dominant curing reaction in low DGEBA compositions, and another type of curing reaction with relatively large activation energy and pre‐exponential factor also occurred, which becomes dominant when the DGEBA content reaches above 70 wt %. FTIR studies also revealed that two types of reactions do exist during the curing of polycaprolactam with DGEBA. It was observed during SEM studies that the reactive blends show multiphase system and on increasing the DGEBA content from 50 to 80 wt %, the mixing of the two phases increased. The reactive blend Ep₈₀Ca₂₀ with 80 wt % DGEBA content exhibits a single‐phase system because of better mixing of the two phases. The results of thermogravimetric analysis also indicate that the initial degradation temperature (T_i), activation energy (E), and pre‐exponential factor (Z) increased with increasing DGEBA content from 50 to 80 wt % in the reactive blends and increased drastically above 70 wt % DGEBA content due to the higher crosslink density. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 687–697, 2004     

Thermo mechanical behaviour of unsaturated polyester toughened epoxy–clay hybrid nanocomposites

The intercrosslinked networks of unsaturated polyester (UP) toughened epoxy–clay hybrid nanocomposites have been developed. Epoxy resin (DGEBA) was toughened with 5, 10 and 15% (by wt) of unsaturated polyester using benzoyl peroxide as radical initiator and 4,4′-diaminodiphenylmethane as a curing agent at appropriate conditions. The chemical reaction of unsaturated polyester with the epoxy resin was carried out thermally in presence of benzoyl peroxide-radical initiator and the resulting product was analyzed by FT-IR spectra. Epoxy and unsaturated polyester toughened epoxy systems were further modified with 1, 3 and 5% (by wt) of organophilic montmorillonite (MMT) clay. Clay filled hybrid UP-epoxy matrices, developed in the form of castings were characterized for their thermal and mechanical properties. Thermal behaviour of the matrices was characterized by differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA) and dynamic mechanical analysis (DMA). Mechanical properties were studied as per ASTM standards. Data resulted from mechanical and thermal studies indicated that the introduction of unsaturated polyester into epoxy resin improved the thermal stability and impact strength to an appreciable extent. The impact strength of 3% clay filled epoxy system was increased by 19.2% compared to that of unmodified epoxy resin system. However, the introduction of both UP and organophilic MMT clay into epoxy resin enhanced the values of mechanical properties and thermal stability according to their percentage content. The impact strength of 3% clay filled 10% UP toughened epoxy system was increased by 26.3% compared to that of unmodified epoxy system. The intercalated nanocomposites exhibited higher dynamic modulus (from 3,072 to 3,820 MPa) than unmodified epoxy resin. From the X-ray diffraction (XRD) analysis, it was observed that the presence of d ₀₀₁ reflections of the organophilic MMT clay in the cured product indicated the development of intercalated clay structure which in turn confirmed the formation of intercalated nanocomposites. The homogeneous morphologies of the UP toughened epoxy and UP toughened epoxy–clay hybrid systems were ascertained from scanning electron microscope (SEM).     

Curing kinetics and mechanical properties of fast curing epoxy resins with isophorone diamine and N-(3-aminopropyl)-imidazole

Fast curing epoxy resins were prepared by the reactions of diglycidyl ether of bisphenol A with isophorone diamine (IPD) and N-(3-aminopropyl)-imidazole (API), and their curing kinetics and mechanical properties influenced by IPD content were also investigated. The analysis of curing kinetics was based on the nonisothermal differential scanning calorimetry (DSC) data with the typical Kissinger, Ozawa, and Flynn–Wall–Ozawa models, respectively. The glass-transition temperature was also measured by the same technique. Additionally, the mechanical properties including flexural, impact, and tensile performances were tested, and the curing time was estimated by isothermal DSC. The degree of cure (α) dependency of activation energy (E_a ) revealed the complexity of curing reaction. Detailed analysis of the curing kinetics at the molecular level indicated that the dependence of E_a on the α was a combined effect of addition reaction, autocatalytic reaction, viscosity, and steric hindrance. From the nonisothermal curves, the curing reaction mechanism could be proposed according to the increasingly obvious low temperature peaks generated by the addition reaction of epoxy group with the primary amines in API and IPD molecules. Using the preferred resin formulation, the resin system could be cured within 10 min at 120 °C with a relatively good mechanical performance. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47950.