Synthesis and properties of fluorinated bis‐benzocyclobutene‐terminated arylene ether monomers

Four novel bis‐benzocyclobutene‐endcapped arylene ether monomers, 1,1′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐1‐phenyl‐2,2,2‐trifluoroethane (BOPP3FE), 1,1′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐1‐(3′,5′‐ditrifluoromethyl)phenyl‐2,2,2‐trifluoroethane(BOPP9FE), 2,2′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐1,1,1,3,3,3‐hexfluoropropane (BOP6FP), and 2,2′‐bis[4‐(4′‐benzocyclobutenyloxy)phenyl]‐propane (BOPP) were prepared and characterized. All the four monomers showed similar curing behaviors under N₂ (Differential scanning calorimetry: extrapolated onset and peak temperatures at 225–229°C and 261–263°C) and demonstrated low and steady melt viscosities between 110 and 200°C, indicating their good processability. After cure, the resulting BCB resins exhibited high T_g (232–282°C) and excellent thermal stability (T_5% > 433°C). The resins also showed good mechanical properties with the flexural strengths of 68–88 MPa and the flexural modulus of 2.52–3.15 GPa. Moreover, the resins also exhibited low dielectric constants (2.58–2.88), low dissipation factors (2.7 to 8.4 × 10?4) and low water absorptions in boiling water for 24 h (0.29–0.59%). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of fluorinated polyimides from 1,1‐bis(4‐amino‐3,5‐dimethylphenyl)‐1‐(3,4,5‐trifluorophenyl)‐2,2,2‐trifluoroethane and various aromatic dianhydrides

A novel aromatic diamine, 1,1‐bis(4‐amino‐3,5‐dimethylphenyl)‐1‐(3,4,5‐trifluorophenyl)‐2,2,2‐trifluoroethane, containing a pendant polyfluorinated phenyl group, a trifluoromethyl group, and methyl groups ortho‐substituted to the amino groups in the structure was synthesized and characterized. The diamine was polymerized with several aromatic dianhydrides, including 3,3′,4,4′‐biphenyltetracarboxylic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride, 4,4′‐oxydiphthalic anhydride, and 4,4′‐hexafluoroisopropylidene diphthalic anhydride, via a high‐temperature one‐step procedure to afford four polyimides (PIs) with inherent viscosities of 0.47–0.70 dL/g. The PIs exhibited excellent solubilities in a variety of organic solvents. They were soluble not only in polar aprotic solvents but in many common solvents, such as cyclopentanone, tetrahydrofuran, and even toluene at room temperature. The tough and flexible PI films cast from the PI solutions exhibited good thermal stabilities and acceptable tensile properties. The glass‐transition temperatures were in the range 312–365°C, and the 5% weight loss temperatures were all higher than 480°C in nitrogen. The films had tensile strengths in the range 76–99 MPa, tensile moduli of 2.2–2.8 GPa, and elongations at break of 5–8%. In addition, the PI films exhibited excellent transparency in the visible light region with cutoff wavelength as low as 302 nm and transmittance higher than 88% at the wavelength of 450 nm. The PI films showed low dielectric constants ranging from 2.50–2.68 and low moisture absorptions of less than 0.56%. The good combined properties of the PIs mainly resulted from the synergic effects of the different substituents. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Organosoluble poly(ether imide)s from phthalimidine based and trifluoromethyl substituted bis(ether amine)

A series of new organosoluble and optically transparent poly(ether imide)s (PEIs) were synthesized by the polycondensation of trifluoromethyl substituted and phthalimidine cardo group based bis(ether amine), 3,3‐bis‐[4‐{2′‐trifluoromethyl 4′‐(4″‐aminophenyl)phenoxy}phenyl]‐2‐phenyl‐2, 3‐dihydro‐isoindole‐1‐one with different fluorinated and non‐fluorinated aromatic dianhydrides (2a–e). All the PEIs were well characterized by elemental analysis, NMR, FTIR spectroscopy, and gel permeation chromatography (GPC). The synthesized PEIs showed moderate to high inherent viscosity 0.41–0.61 dL/g and excellent solubility at room temperature in different organic solvents. All the transparent yellow films showed cut‐off length upto 425 nm. They exhibited high tensile strengths upto 98 MPa, excellent thermostability upto 554°C for 5% weight loss, high glass transition temperature upto 327°C, and water uptake value less than 0.6%. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and properties of soluble aromatic polyetherimides based on 2,2‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]hexafluoropropane dianhydride

Aromatic polyetherimides were synthesized from a fluorine containing aromatic carboxylic acid dianhydride, 2,2‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]hexafluoropropane dianhydride (6F‐BABPA) and five typical aromatic diamines including 1,1‐bis(4‐aminophenyl)‐1‐phenyl‐2,2,2‐trifluoroethane (3F‐DAM) by two‐step procedures—amidation to polyamic acids (PAA), followed by thermal imidization of PAA. The chemical and physical properties of the newly prepared polyetherimides (PEI) were compared in terms of their chemical structures, inherent viscosities, mechanical, and thermal properties. All polyetherimides were well soluble in common organic solvents such as N‐methyl‐2‐pyrolidone (NMP), N,N‐dimethylformamide (DMF), N,N‐dimethylacetamide (DMAc), pyridine, and methylene chloride. A PEI prepared from 6F‐BABPA/3F‐DAM was especially easily dissolved in NMP. The glass transition temperature (T_g) range of the obtained PEI was 209–257°C. The dielectric constants and refractive index were 2.8–3.2 and 1.61–1.56, respectively. The polyetherimide, 6F‐BABPA/BAPP, with a low fluorine content (11.4% fluorine content), has 0.99% water absorption, whereas the polyetherimide, 6F‐BABPA/4‐BDAP, having a high fluorine content (26.0% fluorine content) showed 0.35% of water absorption. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 249–257, 2000     

Solution‐processable and electroactive aromatic polyamides with 3,5‐bis(trifluoromethyl)triphenylamine moiety

New fluorine‐containing, triphenylamine‐based diamine and dicarboxylic acid monomers, namely 3,5‐bis(trifluoromethyl)‐4′,4″‐diaminotriphenylamine and 3,5‐bis(trifluoromethyl)‐4′,4″‐dicarboxytriphenylamine, were synthesized and polymerized with commercially available aromatic dicarboxylic acids and diamines, respectively, leading to two series of aromatic polyamides, 5a–h and 7a–e . Most of the polyamides were amorphous and readily soluble in many common organic solvents and could be solution‐cast into transparent, flexible and strong films with good mechanical properties. The polyamides had useful levels of thermal stability associated with high glass transition temperatures of 273–305 °C and 10% weight‐loss temperatures in excess of 500 °C. Cyclic voltammograms of films of polymers 5a–h on indium–tin oxide‐coated glass substrates exhibited reversible oxidation redox couples with E_1/2 around 1.15 V versus Ag/AgCl in tetrabutylammonium perchlorate/acetonitrile solution, accompanied by a color change from colorless neutral state to reddish brown oxidized state. The 7 series polymers displayed a higher oxidation potential and less electrochemical stability as compared to the 5 series analogues. © 2017 Society of Chemical Industry     

Adhesion property of novel polyimides with 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride

Novel polyimides were synthesized from 1‐[3′,5′‐bis(trifluoromethyl)phenyl] pyromellitic dianhydride (6FPPMDA) by a conventional two‐step process: the preparation of poly(amic acid) followed by solution imidization via refluxing in p‐chlorophenol. The diamines used for polyimide synthesis included bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, bis(3‐aminophenyl)‐4‐trifluoromethylphenyl phosphine oxide, and bis(3‐aminophenyl)phenyl phosphine oxide. The synthesized polyimides were designed to have a molecular weight of 20,000 g/mol by off‐stoichiometry and were characterized by Fourier transform infrared, NMR, differential scanning calorimetry, and thermogravimetric analysis. In addition, their intrinsic viscosity, solubility, water absorption, and coefficient of thermal expansion (CTE) were also measured. The adhesion properties of the polyimides were evaluated via a T‐peel test with bare and silane/Cr‐coated Cu foils, and the failure surfaces were investigated with scanning electron microscopy. The 6FPPMDA‐based polyimides exhibited high glass‐transition temperatures (280–299°C), good thermal stability (>530°C in air), low water absorption (1.46–2.16 wt %), and fairly low CTEs (32–40 ppm/°C), in addition to good adhesion properties (83–88 g/mm) with silane/Cr‐coated Cu foils. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1801–1809, 2005     

Preparation and properties of novel soluble aromatic polyetherimides from 1,1′-bis[4-(3,4-dicarboxyphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane dianhydride and aromatic diamines

New aromatic polyetherimides containing the 1,1′-bis[4-(3,4-dicarboxyphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane dianhydride unit were prepared by a conventional two-step method from 1,1′-bis[4-(3,4-dicarboxyphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane dianhydride and several diamines. This procedure yielded high molecular weight polyetherimides with inherent viscosities of 0.22–1.29 dL/g. Most of the corresponding polyetherimides were soluble in organic solvents such as N-methyl-2-pyrrolidone, N, N-dimethylformamide, N,N-dimethylacetamide, and methylene chloride under ambient temperature. The glass transition temperatures (T_g) of these polymers were in the range of 207–264°C and the temperatures of 10% weight loss were over 520°C at a heating rate 20°C/min in nitrogen. © 1996 John Wiley & Sons, Inc.     

Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Silver–polyimide nanocomposite membranes: Macromolecular‐matrix‐mediated metallization of an aromatic,fluorinated polyimide yielding highly reflective films at low metal concentrations

Highly reflective, surface‐metalized, flexible polyimide films were prepared by the incorporation of a soluble silver‐ion complex, (hexafluoroacetylacetonato)silver(I) (AgHFA), into dimethylacetamide solutions of poly(amic acid) prepared from 2,2‐bis(3,4‐dicarboxyphenyl)hexafluoropropane dianhydride and 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane. The thermal curing of solution‐cast silver(I)–poly(amic acid) films to 300°C led to cycloimidization of the amic acid with concomitant silver(I) reduction and the formation of a reflective, air‐side‐silvered surface at very low (2 wt % and 0.3 vol %) silver concentrations. The reflective surface evolved only when the cure temperature reached about 275°C, although X‐ray diffraction showed metallic silver in the hybrid film by 200°C. After a maximum specular reflectivity greater than 80% was achieved for the 2 wt % silver film, the specular reflectivity diminished sharply with further heating at a constant temperature of 300°C. Incorporating the AgHFA complex into the soluble, fully imidized form of poly{(1,3‐dihydro‐1,3‐dioxo‐2H‐isoindole‐2,5‐diyl)[2,2,2‐trifluoro‐1‐(trifluoromethyl)ethylidene](1,3‐dihydro‐1,3‐dioxo‐2H‐isoindole‐5,2‐diyl)‐1,4‐phenyleneoxy‐1,4‐phenylene[2,2,2‐trifluoro‐1‐(trifluoromethyl)ethylidene]‐1,4‐phenyleneoxy‐1,4‐phenylene} gave films that were 25% less reflective than those beginning with poly(amic acid). Though highly reflective, the films were not electrically conductive. The metalized membranes were thermally stable and maintained mechanical properties similar to those of the parent polyimide. Transmission electron microscopy revealed an air‐side, near‐surface layer of silver that was about 40 nm thick; the interior of the film had well‐dispersed metal particles with diameters mostly less than 2 nm. The near‐surface silver layer maintained its integrity because of physical entrapment of the metal nanoparticles beneath a thin layer of polyimide; that is, the practical adhesion of the metal layer was good. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2409–2418, 2007     

Highly Efficient and Enantioselective Iridium‐Catalyzed Asymmetric Hydrogenation of N‐Arylimines

A catalytic method employing the cationic iridium‐(S_c,R_p)‐DuanPhos [(1R,1′R,2S,2′S)‐2,2′‐di‐tert‐butyl‐2,2′,3,3′‐tetrahydro‐1H,1′H‐1,1′‐biisophosphindole] complex and BARF {tetrakis[3,5‐bis(trifluoromethyl)phenyl]borate} counterion effectively catalyzes the enantioselective hydrogenation of acyclic N‐arylimines with high turnover numbers (up to 10,000 TON) and excellent enantioselectivities (up to 98% ee), achieving the practical synthesis of chiral secondary amines.     

Synthesis,characterization, thermal and optical properties of soluble polyimides derived from an unsymmetrical diamine

A new unsymmetrical diamine monomer, 2,4‐diaminophenyl [4′‐(2′′,6′′‐diphenyl‐4′′‐pyridyl)phenyl]ether, was successfully synthesized by nucleophilic substitution of 1‐chloro‐2,4‐dinitrobenzene with 4‐(2′,6′‐diphenyl‐4′‐pyridyl) phenol. The diamine monomer was characterized by FTIR, ¹H and ¹³C NMR, and elemental analysis techniques and used for the preparation of novel polyimides (PIs) by reaction with commercially available tetracarboxylic dianhydrides such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs with inherent viscosities ranged from 0.43 to 0.48 dL/g were readily soluble in many organic solvents and afforded tough and flexible films by solution casting. These polymers exhibited T_gs between 237 and 294°C, and 10% weight loss temperatures in excess of 500°C with up to 56% char yield at 600°C in air. Their maximum fluorescence emission in dilute (0.2 g/dL) NMP solution appeared at 450 nm. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Organosoluble, Low-Colored Fluorinated Polyimides Based on 1,1-Bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane

A novel trifluoromethyl-substituted bis(ether amine) monomer, 1,1-bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane, was synthesized that led to a series of novel fluorinated polyimides via chemical imidization route when reacted with various commercially available aromatic tetracarboxylic dianhydrides. These polyimides were highly soluble in a variety of organic solvents such as N-methyl-2-pyrrolidone and N,N -dimethylacetamide, and most of them could afford transparent, low-colored, and tough films. These polyimides exhibited glass-transition temperatures (T _gs) of 227–269 °C and showed no significant decomposition below 500 °C under either nitrogen or air atmosphere. These polyimides had low dielectric constants of 2.87–3.17 at 10 kHz, low water uptake of 0.13%–0.58%, and an ultraviolet-visible absorption cutoff wavelength at 364–410 nm. For a comparative study, a series of analogous polyimides based on 1,1-bis[4-(4-aminophenoxy)phenyl]-1-phenyl-2,2,2-trifluoroethane were also prepared and characterized.     

Synthesis and characterization of organosoluble poly(arylate‐imide)s prepared from direct polycondensation of bis(trimellitimide)‐diacids and various bisphenols

Three diimide‐diacids, 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane ( I‐A ), 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]propane ( I‐B ), and 5,5′‐bis[4‐ (4‐trimellitimidophenoxy)phenyl]hexahydro‐4,7‐methanoindan ( I‐C ), were prepared by the azeotropic condensation of trimellitic anhydride with three analogous diamines. Three series of alternating aromatic poly(arylate‐imide)s, having inherent viscosities of 0.41–0.82 dL/g, were synthesized from these diimide‐diacids ( I‐A , I‐B , and I‐C ) with various bisphenols by direct polycondensation using diphenyl chlorophosphate and pyridine as condensing agents. All of the polymers were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, and even in the less polar tetrahydrofuran. These polymers could be cast into transparent and tough films, which had strength at break values ranging from 73 to 98 MPa, elongation at break from 6 to 11%, and initial modulus from 1.6 to 2.2 GPa. The softening temperatures of the polymers were recorded at 145–248°C. They had 10% weight loss at a temperature above 450°C and left 35–51% residue even at 800°C in nitrogen. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3818–3825, 2003     

Synthesis and characterization of soluble copolyimides containing chalcone and phosphine oxide moieties in the main chain

The functional diamines 3,3′‐diaminochalcone and bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide were successfully prepared by simple and convenient procedures with short reaction times, and the overall yields were 78 and 70%, respectively. Copolyimides prepared from 3,3′‐diaminochalcone, bis(3‐aminophenyl)‐3,5‐bis(trifluoromethyl)phenyl phosphine oxide, and 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride exhibited excellent solubility in several organic solvents, such as dimethyl sulfoxide, N,N‐dimethylformamide, N‐methyl pyrrolidone, tetrahydrofuran, and acetone. They also showed very good thermal stability even up to 450°C for 5% weight loss (by thermogravimetric analysis) in nitrogen and a high glass‐transition temperature up to 274°C (by differential scanning calorimetry) in nitrogen. The copolymers' adhesive and photoreactive properties were also investigated, and it was confirmed that the copolyimide containing chalcone and phosphine oxide moieties in the main chain had good adhesiveness and photoreactivity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel phenyl‐substituted poly(p‐phenylene vinylene) derivatives

Two novel phenyl‐substituted poly(p‐phenylene vinylene) derivatives, poly{2‐[3′,4′‐(2″‐ethylhexyloxy)(3″,7″‐dimethyloctyloxy)benzene]‐1,4‐phenylenevinylene} (EDP‐PPV) and poly{2‐[3′,4′‐(2″‐ethylhexyloxy)(3″,7″‐dimethyloctyloxy)benzene]‐5‐methoxy‐1,4‐phenylenevinylene} (EDMP‐PPV), and their copolymer, poly{2‐[3′,4′‐(2″‐ethylhexyloxy)(3″,7″‐dimethyloctyloxy)benzene]‐1,4‐phenylene‐vinylene‐co‐2‐[3′,4′‐(2″‐ethylhexyloxy)(3″,7″‐dimethyloctyloxy)benzene]‐5‐methoxy‐1,4‐phenylenevinylene} (EDP‐co‐EDMP‐PPV; 4:1, 1:1, and 1:4), were successfully synthesized according to the Gilch route. The structures and properties of the monomers and the resulting conjugated polymers were characterized with ¹H‐NMR, ¹³C‐NMR, elemental analysis, gel permeation chromatography, thermogravimetric analysis, ultraviolet–visible absorption spectroscopy, and photoluminescence and electroluminescence (EL) spectroscopy. The EL polymers possessed excellent solubility in common solvents and good thermal stability with a 5% weight loss temperature of more than 380°C. The weight‐average molecular weights and polydispersity indices of EDP‐PPV, EDMP‐PPV, and EDP‐co‐EDMP‐PPV were 1.40–2.58 × 10⁵, and 1.19–1.52, respectively. Double‐layer light‐emitting diodes with the configuration of indium tin oxide/polymer/tris(8‐hydroxyquinoline)aluminum/Al devices were fabricated, and EDP‐co‐EDMP‐PPV (1:1) showed the highest EL performance and exhibited a maximum luminance of 1050 cd/m² at 19.5 V. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1259–1266, 2005     

Synthesis and characterization of a novel siloxane‐imide‐containing polybenzoxazine

A novel siloxane‐imide‐containing polybenzoxazine based on N,N′‐bis(N‐phenyl‐3,4‐dihydro‐2H‐benzo[1,3]oxazine)‐5, 5′‐bis(1,1′,3,3′‐tetramethyldisiloxane‐1,3‐diyl)‐bis(norborane‐2,3‐dicarboximide) (BZ‐A1) was successfully synthesized. The thermal properties of BZ‐A1 are superior to those of conventional polybenzoxazines lacking siloxane groups. Polymerized BZ‐A1 possesses extremely low surface free energy (γ_s = 15.1 mJ m^?2) after curing at 230 °C for 1 h. Moreover, the surface free energy of polymerized BZ‐A1 is more stable than conventional bisphenol A‐type polybenzoxazine during thermal curing and annealing processes, indicating that polymerized BZ‐A1 is more suitable for applications requiring low surface free energy materials for high temperatures over long periods of time. Copyright © 2010 Society of Chemical Industry     

High‐optical transparency and low‐dielectric constant of new organosoluble polyamides containing trifluoromethyl and xanthene groups

A series of fluorinated polyamides was prepared directly by low‐temperature polycondensation of a new cardo diacid chloride, 9,9‐bis[4‐(4‐chloroformylphenoxy)phenyl]xanthene (BCPX), with various diamines containing trifluoromethyl substituents in N,N‐dimethylacetamide (DMAc). Almost all polyamides showed excellent solubility in amide‐type solvents such as DMAc and could also be dissolved in pyridine, m‐cresol, and tetrahydrofuran. These polymers had inherent viscosities between 0.77 and 1.31 dL g^?1, and their weight‐average molecular weights and number‐average molecular weights were in the range of 69,000–102,000 and 41,000–59,000, respectively. The resulting polymers showed glass transition temperatures between 240–258°C and 10% weight loss temperatures ranging from 484°C to 517°C and 410°C to 456°C in nitrogen and air, respectively, and char yields at 800°C in nitrogen higher than 55%. All polymers were amorphous and could be cast into transparent, light‐colored, and flexible films with tensile strengths of 81–100 MPa, elongations at break of 8–12%, and tensile modulus of 1.6–2.1 GPa. These polymers had low‐dielectric constants of 3.34–3.65 (100 kHz), low‐moisture absorption in the range of 0.76–1.91%, and high transparency with an ultraviolet–visible absorption cut‐off wavelength in the 322–340 nm range. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The preparation of α‐bis and α,ω‐tetrakis aromatic oxazolyl‐ and carboxyl‐functionalized polymers using 1,1‐bis[4‐(2‐(4,4‐dimethyl‐1,3‐oxazolyl))phenyl]ethylene in atom transfer radical polymerization reactions

The preparation of new compounds, 1,1‐bis[4‐(2‐(4,4‐dimethyl‐1,3‐oxazolyl))phenyl]ethanol and a new symmetrically disubstituted 1,1‐diphenylethylene derivative, 1,1‐bis[4‐(2‐(4,4‐dimethyl‐1,3‐oxazolyl))phenyl]ethylene, is described. 1,1‐Bis[4‐(2‐(4,4‐dimethyl‐1,3‐oxazolyl))phenyl]ethylene was utilized as a dioxazolyl initiator precursor for the polymerization of styrene by atom transfer radical polymerization (ATRP) methods to produce α‐bis(oxazolyl) polystyrene. The kinetic study of the polymerization process indicated that the free radical polymerization reaction for the preparation of α‐bis(oxazolyl) polystyrene follows first‐order rate kinetics with respect to monomer consumption. α,ω‐Tetrakis(oxazolyl) polystyrene was prepared by a new, in situ, controlled/living, post‐ATRP chain‐end‐functionalization reaction which involves the direct addition of 1,1‐bis[4‐(2‐(4,4‐dimethyl‐1,3‐oxazolyl))phenyl]ethylene to the ω‐terminus of the α‐bis(oxazolyl) polystyrene derivative, without the isolation and purification of the polymeric precursor. α‐Bis(carboxyl) and α,ω‐tetrakis(carboxyl) polystyrene derivatives were obtained by the quantitative chemical transformation of the oxazoline groups of the respective aromatic oxazolyl chain‐end‐functionalized polystyrene derivatives to the aromatic carboxyl groups. The organic precursor compounds, the dioxazolyl‐functionalized 1,1‐diphenylethylene derivative and the functionalized polymers were characterized using ¹H NMR and ¹³C NMR spectrometry and Fourier transform infrared spectroscopy, size‐exclusion and thin‐layer chromatography and non‐aqueous titration measurements. © 2014 Society of Chemical Industry     

Organosoluble and light‐colored fluorinated polyimides based on 1,1‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐1‐phenylethane and various aromatic dianhydrides

To investigate the CF₃ group affecting the coloration and solubility of polyimides (PI), a novel fluorinated diamine 1,1‐bis[4‐(4‐amino‐2‐ trifluoromethylphenoxy)phenyl]‐1‐phenylethane (2) was prepared from 1,1‐ bis(4‐hydrophenyl)‐1‐phenylethan and 2‐chloro‐5‐nitrobenzotrifluoride. A series of light‐colored and soluble PI 5 were synthesized from 2 and various aromatic dianhydrides 3a–f using a standard two‐stage process with thermal 5a– f(H) and chemical 5a–f(C) imidization of poly(amic acid). The 5 series had inherent viscosities ranging from 0.55 to 0.98 dL/g. Most of 5a–f(H) were soluble in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone (NMP), N,N‐ dimethylacetamide (DMAc), and N,N‐dimethylformamide (DMF), and even soluble in less polar solvents, such as m‐Cresol, Py, Dioxane, THF, and CH₂Cl₂, and the 5(C) series was soluble in all solvents. The GPC data of the 5a–f(C) indicated that the Mn and Mw values were in the range of 5.5–8.7 × 10⁴ and 8.5–10.6 × 10⁴, respectively, and the polydispersity index (PDI) Mw /Mn values were 1.2–1.5. The PI 5 series had excellent mechanical properties. The glass transition temperatures of the 5 series were in the range of 232–276°C, and the 10% weight loss temperatures were at 505–548 °C in nitrogen and 508–532 °C in air, respectively. They left more than 56% char yield at 800°C in nitrogen. These films had cutoff wavelengths between 356.5–411.5 nm, the b* values ranged from 5.0–71.1, the dielectric constants, were 3.11–3.43 (1MHz) and the moisture absorptions were in the range of 011–0.40%. Comparing 5 containing the analogous PI 6 series based on 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐ phenylethane (BAPPE), the 5 series with the CF₃ group showed lower color intensity, dielectric constants, and better solubility. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2399–2412, 2005     

Synthesis,characterization, and comparison of properties of novel fluorinated poly(imide siloxane) copolymers

Four new poly(imide siloxane) copolymers were prepared by a one‐pot solution imidization method at a reaction temperature of 180°C in ortho‐dichlorobenzene as a solvent. The polymers were made through the reaction of o‐diphthaleic anhydride with four different diamines—4,4′‐bis(p‐aminophenoxy‐3,3″‐trifluoromethyl) terphenyl, 4,4′‐bis(3″‐trifluoromethyl‐p‐aminobiphenyl ether)biphenyl, 2,6‐bis(3′‐trifluoromethyl‐p‐aminobiphenyl ether)pyridine, and 2,5‐bis(3′‐trifluoromethyl‐p‐aminobiphenylether)thiopene—and aminopropyl‐terminated poly dimethylsiloxane as a comonomer. The polymers were named 1a , 1b , 1c , and 1d , respectively. The synthesized polymers showed good solubility in different organic solvents. The resulting polymers were well characterized with gel permeation chromatography, IR, and NMR techniques. ¹H‐NMR indicated that the siloxane loading was about 36%, although 40 wt % was attempted. ²⁹Si‐NMR confirmed that the low siloxane incorporation was due to a disproportionation reaction of the siloxane chain that resulted in a lowering of the siloxane block length. The films of these polymers showed low water absorption of 0.02% and a low dielectric constant of 2.38 at 1 MHz. These polyimides showed good thermal stability with decomposition temperatures (5% weight loss) up to 460°C in nitrogen. Transparent, thin films of these poly(imide siloxane)s exhibited tensile strengths up to 30 MPa and elongations at break up to 103%, which depended on the structure of the repeating unit. The rheological properties showed ease of processability for these polymers with no change in the melt viscosity with the temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008