Elaboration and dielectric property of modified PZT/epoxy nanocomposites

Composites of lead zirconate titanate (PZT) 50 nm nanoparticles and epoxy resins have been produced with various PZT contents from 0 to 20 wt%. The morphology and thermal properties of prepared composites were characterized using scanning electron microscopy and differential scanning calorimetry. The PZT nanoparticles were found to be well dispersed in the epoxy resin matrix. The glass transition temperature (T_g) value of the nanocomposites increases from 164 to 178°C with increasing the PZT weight fraction. The dielectric composites properties dependences were studied via a wide range of frequency from 10 Hz to 100 kHz. The dielectric constant of PZT/epoxy composite was increased from 5.56 to 6.29 (at f = 1 kHz, T = 30°C), respectively to the incorporated PZT amount, and these values are higher than that the dielectric constant of pure cured epoxy resin, ε = 4.86. POLYM. COMPOS., 37:455–461, 2016. © 2014 Society of Plastics Engineers     

Polydimethylsiloxane–PbZr0.52Ti0.48O3 nanocomposites with high permittivity: Effect of poling and temperature on dielectric properties

Polydimethylsiloxane (PDMS)/lead zirconate titanate (PbZr_0.52Ti_0.48O₃, PZT)-based nanocomposites with high dielectric constant (permittivity, k) are prepared through room temperature mixing. The effect of PZT loading on electrical and mechanical properties of the PDMS–PZT composites is extensively studied. It is found that there is significant increase in permittivity with PZT loading and decrease in volume resistivity. All the composites have low dielectric loss compared to permittivity value. It is observed that there is increase in permittivity and decrease in volume resistivity of composites after poling, which is due to the dipolar polarization. It is found that both permittivity (ε′) and alternating current conductivity (σ_ac) are increased with temperature at low frequency (1 Hz) and decreased with temperature at high frequency (1 MHz). The above composites are sensitive to external pressure and can be used as pressure/force sensor. The tensile strength and % elongation at break decreases with PZT loading, which is due to the nonreinforcing behavior of PZT ceramic. PZT particles distribution and dispersion in PDMS matrix are observed through field emission scanning electron microscopy, high resolution transmission electron microscopy, and atomic force microscopy/scanning probe microscopy. Thermal stability of composites increased with the PZT loading which is due to higher thermal stability of PZT particles compared to PDMS matrix. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47307.     

Electrical properties of polycarbonate/expanded graphite nanocomposites

In present study, polymer matrix nanocomposites based on polycarbonate as matrix and expanded graphite (EG) as reinforcement were fabricated using a simple solution method followed by hot pressing. Scanning electron microscopy revealed almost uniform dispersion and three dimensional networks of EG particles in the matrix. The dc and ac electrical conductivities of the nanocomposites increased with increasing EG content in the matrix. The electrical percolation threshold was observed between 1 and 2 wt % EG. The improvement in the conductivity of 10 wt % nanocomposite was found more than 13 orders of magnitude higher than that of pure matrix. The dielectric constant (at 1 MHz) of the nanocomposite containing 10 wt % EG was increased to about 137. The significant increase in electrical conductivity, dielectric constant, and dissipation factor for the nanocomposites might be good for the applications in antistatic/electromagnetic interference shielding applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47274.     

Role of Cenosphere Addition on Dielectric Properties of Sisal Fiber-Polypropylene Composites

This research investigates the influence of addition of porous additives on dielectric constant of polypropylene. Composite composed of PP matrix with sisal fiber having cylindrical pores and cenospheres having spherical pore, presents low dielectric constant. A new relation concerning porosity is proposed by modifying the usual mixing rule to predict the dielectric constant of PP composite. This research presents the dielectric properties of sisal fiber-reinforced PP composites with and with out cenospheres. Treated and untreated cenospheres with different concentration were loaded in chopped sisal fiber-reinforced polypropylene. The loading of the polypropylene with the sisal fiber, increases the dielectric constant ε′ and improves the ac conductivity σ_ac. The effect of temperature on the dielectric spectrum of polypropylene composites was investigated in the frequency range ranging from 1–10 kHz. Sisal fiber-reinforced polypropylene composites having 20% sisal fiber with and without cenospheres were developed and electrical properties such as dielectric constant (?′), dissipation factor (tanδ) and ac conductivity (σ_ac) of these composites were determined. Dielectric constant, tan δ, and a.c. conductivity increases with increase in temperature at different frequencies.     

Ferroelectric hysteresis behavior and dielectric properties of 1–3 lead zirconate titanate–cement composites

Lead zirconate titanate (PZT) ceramic was mixed with Portland cement (PC) to form 1–3 connectivity PZT–PC composite using a dice-and-fill technique. Ferroelectric hysteresis behavior and dielectric properties of these composites were investigated using PZT volume content of 60%, 70% and 80%. The results showed that the dielectric constant of the composite materials increased with PZT content and the dielectric constant (?_r) value is 781 for 80% PZT composite at 1 kHz. The dielectric loss tangent (tan δ) was found to decrease with increasing PZT content and the tan δ value of 80% PZT composite is 0.06. Parallel and series models were also compared to the dielectric measurement results. For the hysteresis measurements, the ferroelectric hysteresis loops can be seen for all composites. The “instantaneous” remnant polarization (P_ir) was found to increase with increasing PZT content from 3.20 to 4.28 μC/cm² at 90 Hz when PZT volume content used was 60% and 80% respectively.     

PVDF‐PZT‐5H composites prepared by hot press and tape casting techniques

Piezoelectric polymer–ceramic composites are promising materials for transducer applications, and they are widely used in underwater hydrophones, biomedical imaging with ultrasound, and nondestructive testing applications. The critical factor in the 0–3 composite is to ensure homogeneous distribution of the filler in the matrix. To ensure this objective, PVDF‐PZT composite was prepared by two different routes: hot press and tape casting techniques. Loss on ignition and scanning electron microscopy studies were conducted to find out the uniformity of the composites prepared. It is found that hot press technique gives better uniformity compared to tape casting technique. PZT concentration was varied from 20 to 60 vol %. Physical and dielectric properties were studied. FT‐IR, DSC, and XRD characterization studies of PVDF were also recorded. Density of the composites was 2.74 to 5.13 g/cm³ as PZT concentration increased from 20 to 60 volume fractions. The dielectric constant of composites at 1 MHz varied from 16.74 to 98.48 as PZT concentration increased from 20 to 60 volume fractions. Hot press technique that combines solution and melt processing was found to be the better method for the preparation of 0–3 composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of heat treatment on the electrical properties of lead zirconate titanate/poly (vinylidene fluoride) composites

Ceramic/polymer composites are attracting increasing interest in materials research and practical applications due to the combination of excellent electric properties of piezoelectric ceramics and good flexibility of polymer matrices. In this case, the crystallization of the polymer has a significant effect on the electric properties of ceramic/polymer composites. Based on different heat treatment methods, the crystallization of poly(vinylidene fluoride) (PVDF) in composites of lead zirconate titanate (PZT) and PVDF can be controlled effectively. PZT/PVDF composites with various PVDF crystallizations exhibit distinctive dielectric and piezoelectric properties. When the crystallization of PVDF is 21%, the PZT/PVDF composites show a high dielectric constant (ε) of 165 and a low dielectric loss (tan δ) of 0.03 at 10³ Hz, and when the crystallization of PVDF reaches 34%, the piezoelectric coefficient (d₃₃) of PZT/PVDF composites can be up to ca 100 pC N^?1. By controlling the crystallization of PVDF, PZT/PVDF composites with excellent dielectric and piezoelectric properties were obtained, which can be employed as promising candidates in high‐efficiency capacitors and as novel piezoelectric materials. Copyright © 2010 Society of Chemical Industry     

Electrical properties of flexible graphene reinforced polyimide composites

The electrical properties of polyimide and the composite at different volumes fractions were studied in the frequency range 200–20 kHz and in the temperature range 30–200 °C. Increasing the volume fraction of graphene up to 10%, resulted in an extremely large increase in the dielectric constant, which indicates the composites remarkable ability to store electric potential energy under the effect of alternating electric field. An increase in dielectric constant was also observed with increasing temperature and decreasing frequency. The outstanding dielectric properties of polyimide graphene nanocomposites are attributed to the large volume fraction of interfaces in the bulk of the material. The measured increase in dielectric constant with increasing temperature was attributed to the segmental mobility of the polymer chains. The AC conductivity for polyimide and the composites was calculated from the loss factor and a remarkably high conductivity was obtained for the composites due to the formation of conducting paths in the matrix by the graphene sheets. Also this study showed that the thermal conductivity of the composites increased sharply with increasing graphene concentration. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45372.     

Enhanced dielectric and ferroelectric properties induced by Ag @ Pb(Zr,Ti)O3 in poly(vinyl alcohol) matrix composites: A solution casting approach

The present research work focused on the dielectric and electrical properties of silver (Ag) doped Pb(Zr,Ti)O₃ (PZT) particles embedded in a matrix of poly(vinyl alcohol) (PVA) via solution casting technique. The structural analysis confirmed the presence of Ag particles and the microstructural study revealed that both Ag and PZT particles were successfully homogenized over the polymer matrix. The Ag–PZT–PVA composites showed enhanced dielectric properties over a wide range of frequency and the dielectric constant value of such composites was significantly increased to 366 (100 Hz) at 1.1 wt % filler loading. The percolation threshold of the Ag–PZT–PVA composites was found to be 0.9 wt %. The experimental result well fitted to the percolation theory. The enhancement of dielectric constant of the resulting composite systems might be attributed to the increment of conductivity of the interlayer between PZT and PVA due to the presence of Ag particles, which improved the space charge polarization and Maxwell–Wagner–Sillars (MWS) polarization effects. Furthermore, the remnant polarization of the unpoled Ag–PZT–PVA composites (2P_r ～1.48 µC/cm² for 1.1.wt % of Ag–PZT) has also improved, which is favorable for enhanced ferroelectric properties of the composites. The present findings of the composites might be exploited in the potential application of high performance energy storage devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45583.     

Optimization of Dielectric Constant of Polycarbonate/Polystyrene Modified Blend by Ceramic Metal Oxide

We modified a polycarbonate (PC)/polystyrene (PS) blend by loading alumina (Al₂O₃) into the blend. X-ray diffraction (XRD) shows a decrease in crystallinity. The optical microscopy and atomic force microscopy (AFM) confirms the homogeneous dispersion of alumina. The differential scanning calorimetry (DSC) data shows improved results in glass transition (T_g) and melting temperature (T_m) of blend systems. The electrical properties of polymer blends modified by Al₂O₃ were studied as a function of frequency (50 Hz–35 MHz) at 323 K. The alumina showed a significant effect in resulting in a high dielectric constant with low dielectric loss and dissipation factor.     

Combining effects of TiO6 octahedron rotations and random electric fields on structural and properties in Na0.5Bi0.5TiO3

The structural and dielectric properties of Na_0.5Bi_0.5TiO₃ (NBT) ceramics and crystals have been investigated and are compared to that of Pb(Zr_0.55Ti_0.45)O₃ (PZT55/45) and Pb(Mg_1/3Nb_2/3)_0.72Ti_0.28O₃ (PMNT 72/28) ceramics. X-ray diffraction (XRD) profiles for (100), (110), (111), (200), (220), and (222) (referred to cubic structure) reveal that the monoclinic structure with Cc space group exists both in the NBT single crystal and ceramics. The diffraction profile obtained with high resolution laboratory XRD for the NBT single crystal can be well described, using Cc model instead of R3c model. The dielectric constant of NBT below T_hump shows some similarity to that of PZT45/55 ceramics below 50°C in which oxygen octahedron rotations cause the frequency dispersion of the dielectric constant. The temperature-dependent dielectric constant for NBT can be deconvolved into two independent processes. The lower temperature process shows a typical relaxor characteristic and follows the Vogel-Fulcher relationship. The other process at higher temperature shows less frequency-dependent behavior. Comparing the dielectric constant of NBT with that of PZT55/45 and PMNT72/28 reveals that both oxygen octahedral rotations and random electric fields play an important role in the frequency dispersion of the dielectric constant for NBT relaxor feroelectric.     

Evaluation of cure characteristic,physico-mechanical,and dielectric properties of calcium copper titanate filled acrylonitrile-butadiene rubber composites: Effect of calcium copper titanate loading

Calcium copper titanate (CCTO) has been synthesized by high temperature solid-state reaction from calcium carbonate, copper (II) oxide, and titanium dioxide as the starting materials. The formation and morphology of CCTO were confirmed by X-ray diffraction, Fourier-transformed infrared spectrophotometry, scanning electron microscopy (SEM), and particle size analysis. In order to develop flexible dielectric materials, acrylonitrile-butadiene rubber (NBR)-based composites were prepared with CCTO content varied from 0 to 120 phr (parts per hundred rubber). The cure characteristics of composites were assessed. High-dielectric constant CCTO particles were blended into NBR to make composites with improved dielectric constant. Results showed that the NBR/CCTO composites had a high dielectric constant (10–20) with low dielectric loss (<0.4) and low conductivity (<10⁻³ μS/cm) at frequencies up to 10⁶ Hz. However, the higher CCTO loadings had agglomeration in the NBR matrix, and thus tensile strength and elongation at break sharply deteriorated due to poor rubber-filler interactions. The results showed lower storage modulus E′ and a reduction in T_g with the incorporation of CCTO in NBR matrix. Moreover, improved thermal stability of the NBR/CCTO composites was achieved. SEM was used to observe the dispersion of CCTO particles in NBR matrix.     

Dielectric properties of cyanoethylated bagasse composites

Bagasse was converted into a thermo-moldable material by cyanoethylation. The effect of reaction conditions employed during the preparation of cyanoethylated bagasse (CE-B) fibers on dielectric properties of hot-pressed composites was studied. Increase in the nitrogen content of the cyanoethylated fiber, i.e., the nitrile groups resulted in an increase in the dielectric constant and a decrease in the dissipation factor (tan δ) peak of the composites. Increase in the reaction temperature and the alkali concentration resulted in a decrease in the dielectric constant and tan δof the composites. Thickness swelling (TS) and equilibrium moisture content of composites conditioned at different relative humidities (RHs) were studied and the extent of the effect of the absorbed moisture on the dielectric properties was also studied. Increase in the nitrogen content, the alkali concentration, and the reaction temperature during the preparation of cyanoethylated fibers resulted in a decrease in TS and moisture absorption of the composites formed. The dielectric properties of the composites conditioned at 60 or 90% RH deteriorated severely. The effect of temperature on the dielectric constant and tan δof a selected CE-B composite was studied. The dielectric constant and tan δincreased as the temperature increased.     

Structural characterization and electrical properties of carbon nanotubes/epoxy polymer composites

The purpose of this study is to identify the relationship between the electrical and structural characteristics of multiwalled carbon nanotubes dispersed into the polymer matrix of a resin. In a first step, the composites were characterized by small‐angle neutron scattering, which provide information about the bulk dispersion of nanotubes in the matrix and form three‐dimensional networks with a surface fractal behavior. In the second step, a dielectric and electrical study was carried out in the frequency range between 1 Hz and 10 MHz at room temperature. We have found that the electric and dielectric behavior of these composites can be described by Jonscher's universal dielectric response. We show that the critical exponents describing the concentration dependence of the conductivity and the dielectric constant, obtained in the vicinity of the percolation threshold, are in good agreement with the theoretical values. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44514.     

Crystal structure refinement,enhanced magnetic and dielectric properties of Na0.5Bi0.5TiO3 modified Bi0.8Ba0.2FeO3 ceramics

(1-x) Na_0.5Bi_0.5TiO₃–x(Bi_0.8Ba_0.2FeO₃) (x=0.5, 0.6, 0.7, and 0.8) ceramics were synthesized via solid state reaction method. Powder X-ray diffraction investigations performed at room temperature along with Rietveld analysis show all the composites to exhibit a rhombohedral distorted perovskite structure, described by space group R3c. Rietveld refinement confirmed a good agreement between observed and calculated intensities and a low value of goodness of fit (χ²). Magnetic measurements were carried out at room temperature up to a field of 6 kOe. Magnetic properties of BBFO modified NBT ceramics are improved with a significant opening in the M–H hysteresis loop at room temperature. Remanent magnetization and coercive field increased with increase of BBFO concentration. The dielectric response of these samples was analyzed in the frequency range 10 Hz–7 MHz at different temperatures revealing a dispersion in dielectric constant (ε′) and in dissipation factor (tan δ) at lower frequencies. Both ε′ and tan δ increase with increase of BBFO content. The temperature dependence of frequency exponent ′s′ of power law suggests that quantum mechanical tunneling (QMT) model to be applicable at lower temperature and correlated barrier hopping (CBH) mechanism to be appropriate at higher temperature to describe the conduction mechanism in x=0.5 and x=0.6 samples. Further, with increase in BBFO content, the dielectric constant becomes more stable at higher frequencies and temperatures thereby improving the dielectric properties of the material.     

Polytetrafluorethylene-based high-k composites with low dielectric loss filled with priderite (K1.46Ti7.2Fe0.8O16)

Composite materials with a high permittivity (high-k) and low dielectric loss represent an important research direction for the rapid development of modern electronic. This article is about high-k composite with low dielectric loss (dielectric constant is approximately 11, and dielectric loss is only 0.02 at 1 MHz and about 50 wt % of filler) based on a polytetrafluorethylene (PTFE) compounded with priderite (K_1.46Ti_7.2Fe_0.8O₁₆). The dielectric permittivity about ε' ≈ 10³ and the dielectric loss of tgδ ≈ 2 have been found for filler content about 50 wt % (30 vol %) and, respectively, ε' ≈ 11 and tgδ ≈ 0.02 for 1 MHz. To produce filler, amorphous potassium polytitanate was synthesized by molten salt method, modified in aqueous solution of iron sulfate, crystallized at 700 °C and further treated in the aqueous dispersion of PTFE. The obtained product was pressured, dried and investigated by X-ray diffraction and scanning electron microscopy. Dielectric properties of the composite with different ceramic filler content (1–90 wt %) were studied using impedance spectroscopy in the frequency range of 10⁻² to 10⁶ Hz. The influence of frequency on electric conductivity, permittivity, and dielectric losses was analyzed taking into account the experimental data on porosity, apparent density obtained for the composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48762.     

Effect of silver coating on electrical properties of sisal fibre-epoxy composites

In this paper, the effect of silver coating and size of fibre on electrical properties of sisal fibre-reinforced epoxy composites has been reported. For this purpose, epoxy composites reinforced with silver-coated sisal (of 5 and 10 mm length) prepared by hand moulding and samples were characterized for their electrical properties, such as dielectric constant (ε′), dielectric dissipation factor (tan δ) and AC conductivity (σ _ac), at different temperatures and frequencies. It was observed that dielectric constant increases with increase in temperature and decreases with increase in frequency from 500 Hz to 5 kHz. The peak height at the transition temperature decreases with increasing frequency. Interestingly, sample having silver-coated fibre of 5 mm length exhibited higher value of dielectric constant as compared to the sample having 10 mm of fibre length, which is attributed to the increased surface area of coated fibre. This behaviour of the material can be explained in terms of interfacial polarization. At a constant volume of fibres and at a length of 5 mm, the number of interfaces per unit volume element is high and this results in high interfacial polarization. The number of interfaces decreases as the fibre length increases and therefore the value of ε′ decreases at 10 mm fibre length. To study the changes in structure of samples, Fourier transform infrared spectrometry and scanning electron microscopy of the samples were carried out.     

Enhanced performance in multilayer-structured nanocomposites using BaTiO3 and Ba0.8Sr0.2TiO3 decorated graphene hybrids

It is challenging to achieve high energy density in conductive fillers/polymer nanocomposites due to their extremely low breakdown strength. In this paper, a novel multi-component and multilayer-structured nanocomposite was designed and investigated, consisting of Ba_0.8Sr_0.2TiO₃ decorated graphene (BST @ RGO)/poly(vinylidene fluoride-chlorotrifluoroethylene) copolymer (P(VDF-CTFE)) composites (R-Layer) as interlayer, and BaTiO₃/P(VDF-CTFE) composites (B-Layer) as surface layer. The multilayer-structured nanocomposites were prepared through layer-by-layer solution casting method. Enhanced breakdown strength, energy density, dielectric constant and low dielectric loss were simultaneously obtained in the nanocomposites by the multilayer structure. The maximum dielectric constant of the composites with multi-layered structure was approximately 14, which was increased by 16.67% compared to the pure P(VDF-CTFE) layer, and the dielectric loss was as low as 0.047 at 1?kHz, even lower than pure P(VDF-CTFE) in frequency range from 10?kHz to 1?MHz. The breakdown strength and energy storage density of BRB-3 nanocomposites with 3 R-Layers reached to 220?kV?mm^?1 and 6.49?J?cm^?3, respectively. These results demonstrated that designing multi-component and multilayer-structured nanocomposites was an effective approach to fabricate high performance dielectric nanocomposites.     

Microwave dielectric properties of flexible butyl rubber–strontium cerium titanate composites

Butyl rubber–strontium cerium titanate (BS) composites have been prepared by hot pressing. The tensile tests show that the BS composites are flexible. The dielectric properties of the composites have been investigated at 1 MHz and 5 GHz as a function of ceramic contents. The composite with volume fraction 0.43 of ceramic filler has a dielectric constant (ε_r) of 11.9 and dielectric loss (tan δ) 1.8 × 10^?3 at 5 GHz. The measured values of ε_r are compared with the effective values calculated using different theoretical models. The thermal conductivity of the composites is found to increase with ceramic contents and reaches a value of 4.5 Wm^?1 K^?1 for maximum filler loading 0.43 volume fraction. The coefficient of thermal expansion of the composites decreases gradually with filler loading and reaches a minimum value of 30.2 ppm °C^?1 at a volume fraction 0.43. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Improved piezoelectric properties of Pb(Zr0·70Ti0.30)O3 ceramics doped with non-polar bismuth manganite

This report documents the electrical features of (1-x) Pb(Zr_0·70Ti_0.30)O₃–x BiMn₂O₅ ceramics with x = 0–0.05 (PZT–BM). A structural disorder was introduced by doping with non-polar bismuth manganite (BM) to increase the chemical disorder in PZT ceramics, which is one of the reasons for its marked piezoelectric properties. The chemical disorder was confirmed using scanning electron microscopy. The rhombohedral symmetry of a crystal lattice was determined using the XRD powder test. To assess the influence of BM dopant on the electric properties of PZT, dielectric spectroscopy was performed at a frequency f = 1 kHz–1 MHz and in a temperature range of 290–680 K. Several effects on the dielectric characteristics were induced by the addition of BM, including the shift and diffuseness of the transition from the ferroelectric to the paraelectric phase and the diffuseness of the transition between two ferroelectric phases. The electrical conductivity increased as the BM content increased. Piezoelectric studies have shown that 0.99 PZT–0.01 BM ceramics exhibit better piezoelectric properties and higher permittivity than pure PZT ceramics. The 0.99 PZT–0.01 BM piezoelectric coefficient d₃₃ increased by approximately 30% compared with pure PZT.