Effect of heat treatment on the microstructure and strength of yttrium silicate matrix-modified SiCf/SiC composites

Yttrium silicate was introduced into the matrix of SiC_f/SiC composites via the slurry impregnation and reactive chemical vapor infiltration (RCVI) methods to improve the water and oxygen corrosion resistance of the modified composite materials. The effects of heat treatment on the modified matrix and strength of the composites were systematically investigated. The results showed that the modified matrix was composed of a mixture of yttrium monosilicate, yttrium disilicate, and silicon carbide. The modified yttrium silicate matrix (named Y-Si-O matrix) and the silicon carbide matrix were laminated and well combined. After heat treatment, the amount of Y-Si-O in the mixed matrix increased. The modified composites with yttrium silicate had a similar flexural strength as SiC_f/SiC composites (∼400 MPa). After treated at 1000 °C – 1300 °C, the strength of the modified composites increased by 17 %–26 %. The highest strength was measured for composites treated at 1200 °C.     

Mechanical properties of SiCf/SiC composites with alternating PyC/BN multilayer interfaces

Alternating pyrolytic carbon/boron nitride (PyC/BN)_n multilayer coatings were applied to the KD–II silicon carbide (SiC) fibres by chemical vapour deposition technique to fabricate continuous SiC fibre-reinforced SiC matrix (SiC_f/SiC) composites with improved flexural strength and fracture toughness. Three-dimensional SiC_f/SiC composites with different interfaces were fabricated by polymer infiltration and pyrolysis process. The microstructure of the coating was characterised by scanning electron microscopy, X–photoelectron spectroscopy and transmission electron microscopy. The interfacial shear strength was determined by the single-fibre push-out test. Single-edge notched beam (SENB) test and three-point bending test were used to evaluate the influence of multilayer interfaces on the mechanical properties of SiC_f/SiC composites. The results indicated that the (PyC/BN)_n multilayer interface led to optimum flexural strength and fracture toughness of 566.0?MPa and 21.5?MPa?m^1/2, respectively, thus the fracture toughness of the composites was significantly improved.     

Influence of pyrolysis and melt infiltration temperatures on the mechanical properties of SiCf/SiC composites

In order to improve the degree of matrix densification of SiC_f/SiC composites based on liquid silicon infiltration (LSI) process, the microstructure and mechanical properties of composites according to various pyrolysis temperatures and melt infiltration temperatures were investigated.Comparing the microstructures of SiC_f/C carbon preform by a one-step pyrolysis process at 600 °C and two-step pyrolysis process at 600 and 1600 °C, the width of the crack and microcrack formation between the fibers and matrix in the fiber bundle increased during the two-step pyrolysis process. For each pyrolysis process, the density, porosity, and flexural strength of the SiC_f/SiC composites manufactured by the LSI process at 1450–1550 °C were measured to evaluate the degree of matrix densification and mechanical properties. As a result, the SiC_f/SiC composite that was fabricated by the two-step pyrolysis process and LSI process showed an 18% increase in density, 16%p decrease in porosity, and 150% increase in flexural strength on average compared to the composite fabricated by the one-step pyrolysis process.In addition, among the SiC_f/SiC specimens fabricated by the LSI process after the same two-step pyrolysis process, the specimen that underwent the LSI process at 1500 °C showed 30% higher flexural strength on average than those at 1450 or 1550 °C. Furthermore, under the same pyrolysis temperature, the mechanical strength of SiC_f/SiC specimens in which the LSI process was performed at 1500 °C was higher than that of the 1550 °C although both porosity and density were almost similar. This is because the mechanical properties of the Tyranno-S grade SiC fibers degraded rapidly with increasing LSI process temperature.     

SiC fiber reinforced geopolymer composites,part 2: Continuous SiC fiber

In this paper, unidirectional SiC fiber (SiC_f) reinforced geopolymer composites (SiC_f/geopolymer) were prepared and effects of fiber contents on the microstructure and mechanical properties of the composites in different directions were investigated. The XRD results showed that addition of SiC_f retarded geopolymerization process of geopolymer matrix by weakening the typical amorphous hump. SiC_f in all the composites were well infiltrated by geopolymer matrix, but microcracks which were perpendicular to the fiber axial direction were noted in the interface area due to the thermal shrinkage of matrix during the curing process. With the increases in fiber contents, although Young's modulus of the composites increased continuously, flexural strength, fracture toughness and work of fracture increased at first, reached their peak values and then decreased. And when fiber content was 20 vol%, the composites showed the highest flexural strength, fracture toughness and work of fracture, which were 14.2, 15.2 and 81.6 times as high as those of pristine geopolymer, respectively, indicating significant strengthening and toughening effects from SiC_f. Meanwhile, SiC_f/geopolymer composites failed in different failure modes in the different directions, i.e., tensile failure mode in the x direction (in-plane and perpendicular to the fiber axial direction) and shear failure mode in the z direction (laminate lay-up direction).     

Effects of in-situ carbon layer and volume fraction of SiC fiber on the mechanical properties and fracture behaviors of SiCf/SiC composites fabricated by a modified PIP method

Unidirectional SiC_f/SiC composites (UD SiC_f/SiC composites) with excellent mechanical properties were successfully fabricated by a modified PIP method which involved the preparation of film-like matrix containing carbon layer with a low concentration PCS solution followed by the rapid densification of composites with a high concentration PCS solution. Carbon layers were in-situ formed and alternating with SiC layers in the as-received matrix. The unique microstructure endows the composites with appropriate interfacial bonding state, good load transfer ability of interphase and matrix and load bearing ability of fiber, and great crack deflection capacity, which ensures the synergy of high strength and toughness of composites. It is also found that the fiber volume fraction in the preform makes a non-negligible effect on the distribution of interphase and matrix, of which the reasonable adjustment can be utilized to optimize the mechanical properties of composites. Compared with the composites only using high concentration PCS solution, the UD SiC_f/SiC composites prepared by the modified PIP method exhibit superior mechanical properties. Ultrahigh flexural strength of 1318.5 ± 158.3 MPa and fracture toughness of 47.6 ± 5.6 MPa·m^1/2 were achieved at the fiber volume fraction of 30%.     

Effect of intermediate heat treatment on mechanical properties of SiCf/SiC composites with BN interphase prepared by ICVI

SiC_f/SiC composites with BN interface were prepared through isothermal-isobaric chemical vapour infiltration process. Room temperature mechanical properties such as tensile, flexural, inter-laminar shear strength and fracture toughness (K_IC) were studied for the composites. The tensile strength of the SiC_f/SiC composites with stabilised BN interface was almost 3.5 times higher than that of SiC_f/SiC composites with un-stabilised BN interphase. The fracture toughness is similarly enhanced to 23 MPa m^1/2 by stabilisation treatment. Fibre push-through test results showed that the interfacial bond strength between fibre and matrix for the composite with un-stabilised BN interface was too strong (>48 MPa) and it has been modified to a weaker bond (10 MPa) due to intermediate heat treatment. In the case of composite in which BN interface was subjected to thermal treatment soon after the interface coating, the interfacial bond strength between fibre and matrix was relatively stronger (29 MPa) and facilitated limited fibre pull-out.     

Effect of pyrolysis temperature on the mechanical evolution of SiCf/SiC composites fabricated by PIP

Three types of SiC_f/SiC composites with a four-step three-dimensional SiC fibre preform and pyrocarbon interface fabricated via precursor infiltration and pyrolysis at 1100 °C, 1300 °C, and 1500 °C were heat-treated at 1300 °C under argon atmosphere for 50 h. The effects of the pyrolysis temperature on the microstructural and mechanical properties of the SiC_f/SiC composites were studied. With an increase in the pyrolysis temperature, the SiC crystallite size of the as-fabricated composites increased from 3.4 to 6.4 nm, and the flexural strength decreased from 742 ± 45 to 467 ± 38 MPa. After heat treatment, all the samples exhibited lower mechanical properties, accompanied by grain growth, mass loss, and the formation of open pores. The degree of mechanical degradation decreased with an increase in the pyrolysis temperature. The composites fabricated at 1500 °C exhibited the highest property retention rates with 90% flexural strength and 98% flexural modulus retained. The mechanism of the mechanical evolution after heat treatment was revealed, which suggested that the thermal stability of the mechanical properties is enhanced by the high crystallinity of the SiC matrix after pyrolysis at higher temperatures.     

Effect of SiC nanowires on the mechanical properties and thermal conductivity of 3D-SiCf/SiC composites prepared via precursor infiltration pyrolysis

In this study, SiC nanowires (SiC_NWS) were grown in situ on the surface of PyC interface through chemical vapor infiltration (CVI) to improve the mechanical characteristics and thermal conductivity of three-dimensional SiC_f/SiC composites fabricated via precursor infiltration pyrolysis (PIP). The effect of SiC_NWS on the properties of the obtained composites was investigated by comparing them with conventional SiC_f/PyC/SiC composites. After the deposition of SiC_NWS, the flexural strength of the SiC_f/SiC composites was found to increase by 46 %, and the thermal conductivity showed an obvious increase at 25?1000 °C. The energy release of the composites in the damage evolution process was analysed by acoustic emission. The results indicated that the damage evolution process was delayed owing to the decrease in porosity, the crack deflection and bridging of the SiC_NWS. Furthermore, the excellent thermal conductivity was attributed to the thermally conductive pathways formed by the SiC_NWS in the dense structure.     

Effects of CVI SiC amount and deposition rates on properties of SiCf/SiC composites fabricated by hybrid chemical vapor infiltration (CVI) and precursor infiltration and pyrolysis (PIP) routes

The SiC_f/SiC composites have been manufactured by a hybrid route combining chemical vapor infiltration (CVI) and precursor infiltration and pyrolysis (PIP) techniques. A relatively low deposition rate of CVI SiC matrix is favored ascribing to that its rapid deposition tends to cause a ‘surface sealing’ effect, which generates plenty of closed pores and severely damages the microstructural homogeneity of final composites. For a given fiber preform, there exists an optimized value of CVI SiC matrix to be introduced, at which the flexural strength of resultant composites reaches a peak value, which is almost twice of that for composites manufactured from the single PIP or CVI route. Further, this optimized CVI SiC amount is unveiled to be determined by a critical thickness t₀, which relates to the average fiber distance in fiber preforms. While the deposited SiC thickness on fibers exceeds t₀, closed pores will be generated, hence damaging the microstructural homogeneity of final composites. By applying an optimized CVI SiC deposition rate and amount, the prepared SiC_f/SiC composites exhibit increased densities, reduced porosity, superior mechanical properties, increased microstructural homogeneity and thus reduced mechanical property deviations, suggesting a hybrid CVI and PIP route is a promising technique to manufacture SiC_f/SiC composites for industrial applications.     

Fine study of hierarchical interphase constructed by boron nitride and carbon nanotubes in SiCf/SiC composites

A fine study of the interfacial part in the silicon carbide fiber (SiC_f) reinforced silicon carbide (SiC) composites was conducted by transmission electron microscopy. The boron nitride (BN) and carbon nanotubes (CNTs) were progressively coated on the SiC_f by chemical vapor deposition method to form a hierarchical structure. Three composites with different interfaces, SiC_f–CNTs/SiC, SiC_f@BN/SiC, and SiC_f@BN–CNTs/SiC, were fabricated by polymer infiltration and pyrolysis method. The interfaces and microstructures of the three composites were carefully characterized to investigate the improvement mechanism of strength and toughness. The results showed that BN could protect the surface of SiC_f from corrosion and oxidation so that improved the possibility of debonding and pullout. CNTs could avoid the propagation of cracks in the composites so that improved the damage resistance of the matrix. The synergistic reinforcement brought by BN and CNTs interfaces made the SiC_f@BN–CNTs/SiC composites with a tensile fracture strength as high as 359 MPa, with an improvement of 23% compared to that of SiC_f@BN/SiC.     

The mechanical,thermophysical and electromagnetic properties of UD SiCf/SiC composites in different directions

Unidirectional (UD) silicon carbide (SiC) fiber-reinforced SiC matrix (UD SiC_f/SiC) composites with CVI BN interphase were fabricated by polymer infiltration-pyrolysis (PIP) process. The effects of the anisotropic distribution of SiC fibers on the mechanical properties, thermophysical properties and electromagnetic properties of UD SiC_f/SiC composites in different directions were studied. In the direction parallel to the axial direction of SiC fibers, SiC fibers bear the load and BN interphase ensures the interface debonding, so the flexural strength and the fracture toughness of the UD SiC_f/SiC composites are 813.0 ± 32.4 MPa and 26.1 ± 2.9 MPa·m^1/2, respectively. In the direction perpendicular to the axial direction of SiC fibers, SiC fibers cannot bear the load and the low interfacial bonding strengths between SiC fiber/BN interphase (F/I) and BN interphase/SiC matrix (I/M) both decrease the matrix cracking stress, so the corresponding values are 36.6 ± 6.9 MPa and 0.9 ± 0.5 MPa?m^1/2, respectively. The thermal expansion behaviors of UD SiC_f/SiC composites are similar to those of SiC fibers in the direction parallel to the axial direction of SiC fibers, and are similiar to those of SiC matrix in the direction perpendicular to the axial direction of SiC fibers. The total electromagnetic shielding effectiveness (EM SE_T) of UD SiC_f/SiC composites attains 32 dB and 29 dB when the axial direction of SiC fibers is perpendicular and parallel to the electric field direction, respectively. The difference of conductivity in different directions is the main reason causing the different SE_T. And the dominant electromagnetic interference (EMI) shielding mechanism is absorption for both studied directions.     

Mechanical and dielectric properties of SiCf/BN/SiBCN composites via different synthesis technologies

SiC fibers reinforced SiBCN ceramic matrix composites (SiC_f/BN/SiBCN composites) were synthesized by direct chemical vapor infiltration (CVI), polymer infiltration pyrolysis (PIP) or chemical vapor infiltration combined with polymer infiltration pyrolysis (CVI + PIP). It is shown that the insertion of a continuous and dense SiBCN matrix via the CVI process improves the flexural strength and modulus. Interface debonding and fiber pullout happened with 50–100 nm BN interface in CVI and CVI + PIP SiC_f/BN/SiBCN composites. The relative complex permittivity was measured in X-band. Higher ε′′ values in CVI-containing composites can be observed, which can be attributed to the accumulation of C and SiC phases and a multilayer matrix. Strong electromagnetic wave attenuation ability was obtained with high dielectric loss.     

Ring compression properties of SiCf/SiC composites prepared by chemical vapor infiltration

SiC fiber reinforced SiC matrix (SiC_f/SiC) composites prepared by chemical vapor infiltration are one of promising materials for nuclear fuel cladding tube due to pronounced low radioactivity and excellent corrosion resistance. As a structure component, mechanical properties of the composites tubes are extremely important. In this study, three kinds of SiC_f preform with 2D fiber wound structure, 2D plain weave structure and 2.5D shallow bend-joint structure were deposited with PyC interlayer of about 150–200?nm, and then densified with SiC matrix by chemical vapor infiltration at 1050?°C or 1100?°C. The influence of preform structure and deposition temperature of SiC matrix on microstructure and ring compression properties of SiC_f/SiC composites tubes were evaluated, and the results showed that these factors have a significant influence on ring compression strength. The compressive strength of SiC_f/SiC composites with 2D plain weave structure and 2.5D shallow bend-joint structure are 377.75?MPa and 482.96?MPa respectively, which are significantly higher than that of the composites with 2D fiber wound structure (92.84?MPa). SiC_f/SiC composites deposited at 1100?°C looks like a more porous structure with SiC whiskers appeared when compared with the composites deposited at 1050?°C. Correspondingly, the ring compression strength of the composites deposited at 1100?°C (566.44?MPa) is higher than that of the composites deposited at 1050?°C (482.96?MPa), with a better fracture behavior. Finally, the fracture mechanism of SiC_f/SiC composites with O-ring shape was discussed in detail.     

The effects of preparation temperature on the SiCf/SiC 3D4d woven composite

Continuous silicon carbide fiber reinforced silicon carbide matrix (SiC_f/SiC) composites have promising applications in aero-engine due to their unique advantages, such as low density, high modulus and strength, outstanding high temperature resistance and oxidation resistance. As SiC fibers are main reinforcements in SiC_f/SiC composites, the crystallization rate and initial damage degree of SiC fibers are seriously influenced by preparation temperatures of SiC_f/SiC composites, namely mechanical properties of SiC fibers and SiC_f/SiC composites are influenced by preparation temperatures. In this paper, KD-II SiC fibers were woven into 3D4d preforms and SiC matrix was fabricated by PIP process at 1100 °C, 1200 °C, 1400 °C and 1600 °C. Digital image correlation (DIC) method was adopted to measure the uniaxial tensile properties of these SiC_f/SiC composites. In addition, finite element method (FEM) based on representative volume element (RVE) was adopted to predict the mechanical properties of SiC_f/SiC composites. The good agreements between numerical results and experimental results of uniaxial tensile tests verified the validity of the RVE. In last, the transverse tensile, transverse shear, uniaxial shear properties were predicted by this method. The predicted results illustrated that axial tensile, transverse tensile and axial shear properties were greatly influenced by the preparation temperatures of SiC_f/SiC composites while transverse shear properties were not significantly various. And the mechanical properties of SiC_f/SiC composites peaked at 1200 °C among these four temperatures while their values reached their lowest points at 1600 °C because of thermal damage and brittle failure of SiC_f/SiC composites.     

Enhanced mechanical and dielectric properties of SiCf/SiC composites with silicon oxycarbide interphase

SiC_f/SiC composites with silicon oxycarbide (SiOC) interphase were successfully prepared using silicone resin as interphase precursor for dip-coating process and polycarbosilane as matrix precursor for PIP process assisted with hot mold pressing. The effects of SiOC interphase on mechanical and dielectric properties were investigated. XRD and Raman spectrum results show that SiOC interphase is composed of silicon oxycarbide and free carbon with a relatively low crystalline degree. The surface morphology of SiC fibers with SiOC interphase is smooth and homogeneous observed by SEM. The flexural strength and failure displacement of SiC_f/SiC composites with SiOC interphase vary with the thickness of interphase and the maximum value of flexural strength is 289 MPa with a failure displacement of 0.39 mm when the thickness of SiOC interphase is 0.25 µm. The complex permittivity of the composites increases from 8.8-i5.7 to 9.8-i8.3 with the interphase thicker.     

Mechanical and dielectric properties of SiCf/SiC composites fabricated by PIP combined with CIP process

2D KD-1 SiC fiber fabrics were employed to fabricate SiC_f/SiC composites by an improved polymer infiltration and pyrolysis (PIP) process, combined with cold isostatic pressing (CIP). The effect of CIP process on the microstructure, mechanical and dielectric properties of SiC_f/SiC composites was investigated. The infiltration efficiency was remarkably improved with the introduction of CIP process. Compared to vacuum infiltration, the CIP process can effectively increase the infiltrated precursor content and decrease the porosity resulting in a dense matrix. Thus SiC_f/SiC composites with high density of 2.11 g cm⁻³ and low porosity of 11.3% were obtained at 100 MPa CIP pressure, together with an increase of the flexural strength of the composites from 89 MPa to 213 MPa. Real part (ε′) and the imaginary part (ε″) of complex permittivity of SiC_f/SiC composites increase and vary from 11.7-i9.7 to 15.0-i12.8 when the CIP pressure reaches 100 MPa.     

Effect of SiCnws on flexural strength of SiCf/HfC-SiC composites after impact and ablation

SiC nanowires (SiC_nws) modified SiC_f/HfC-SiC composites were prepared by precursor infiltration and pyrolysis (PIP) and chemical vapor infiltration (CVI) methods. The microstructure, flexural strengths, impact and impact-ablation tests of the composites with and without SiC_nws were investigated. The results showed that after introducing SiC_nws, not only the retention rate of HfC ceramic produced by PIP was increased obviously, but also the fracture displacement of the modified composites was reduced due to the enhancement effect of SiC_nws at interface between SiC fiber and matrix. After impact and impact-ablation, the strength retention of SiC_nws modified composites was 91.6 % and 69.1 % respectively, higher than that of the composites without SiC_nws (85.2 % and 54.8 %). As the impact resistance of the modified composites was improved by the pull-out and bridging of SiC_nws, the ablation resistance of the impacted composites was enhanced as well.     

Mechanical,thermal, and dielectric properties of SiCf/SiC composites reinforced with electrospun SiC fibers by PIP

Electrospun unidirectional SiC fibers reinforced SiC_f/SiC composites (e-SiC_f/SiC) were prepared with ∼10% volume fraction by polymer infiltration and pyrolysis (PIP) process. Pyrolysis temperature was varied to investigate the changes in microstructures, mechanical, thermal, and dielectric properties of e-SiC_f/SiC composites. The composites prepared at 1100 °C exhibit the highest flexural strength of 286.0 ± 33.9 MPa, then reduced at 1300 °C, mainly due to the degradation of electrospun SiC fibers, increased porosity, and reaction-controlled interfacial bonding. The thermal conductivity of e-SiC_f/SiC prepared at 1300 °C reached 2.663 W/(m∙K). The dielectric properties of e-SiC_f/SiC composites were also investigated and the complex permittivities increase with raising pyrolysis temperature. The e-SiC_f/SiC composites prepared at 1300 °C exhibited EMI shielding effectiveness exceeding 24 dB over the whole X band. The electrospun SiC fibers reinforced SiC_f/SiC composites can serve as a potential material for structural components and EMI shielding applications in the future.     

Microstructure and mechanical properties of quasi-isotropic chopped fiber-reinforced PyC–SiC matrix composite prepared by novel nondamaging method

In this work, quasi-isotropic chopped carbon fiber-reinforced pyrolytic carbon and silicon carbide matrix (C_f/C–SiC) composites and chopped silicon carbide fiber-reinforced silicon carbide matrix (SiC_f/SiC) composites were prepared via novel nondamaging method, namely airlaid process combined with chemical vapor infiltration. Both composites exhibit random fiber distribution and homogeneous pore size. Young's modulus of highly textured pyrolytic carbon (PyC) matrix is 23.01 ± 1.43 GPa, and that of SiC matrix composed of columnar crystals is 305.8 ± 9.49 GPa in C_f/C–SiC composites. Tensile strength and interlaminar shear strength of C_f/C–SiC composites are 52.56 ± 4.81 and 98.16 ± 24.62 MPa, respectively, which are both higher than those of SiC_f/SiC composites because of appropriate interfacial shear strength and introduction of low-modulus and highly textured PyC matrix. Excellent mechanical properties of C_f/C–SiC composites, particularly regarding interlaminar shear strength, are due to their quasi-isotropic structure, interfacial debonding, interfacial sliding, and crack deflection. In addition to the occurrence of crack deflection at the fiber/matrix interface, crack deflection in C_f/C–SiC composites takes also place at the interface between PyC–SiC composite matrix and the interlamination of multilayered PyC matrix. Outstanding mechanical properties of as-prepared C_f/C–SiC composites render them potential candidates for application as thermal structure materials under complex stress conditions.     

Effect of SiC interphase on the mechanical,high-temperature dielectric and high-temperature microwave absorption properties of the SiCf/SiC/Mu composites

In this study, SiC interphase was prepared via a precursor infiltration-pyrolysis process, and effects of dipping concentrations on the mechanical, high-temperature dielectric and microwave absorption properties of the SiC_f/SiC/Mu composites had been investigated. Results indicated that different dipping concentrations influenced ultimate interfacial morphology. The SiC interphase prepared with 5 wt% PCS/xylene solution was smooth and homogeneous, and no bridging between the fiber monofilament could be observed. At the same time, SiC interphase prepared with 5 wt% PCS/xylene solution had significantly improved mechanical properties of the composite. In particular, the flexural strength of the composite prepared with 5 wt% PCS/xylene solution reached 281 MPa. Both ε′ and ε′′ of the SiC_f/SiC/Mu composites were enhanced after preparing SiC interphase at room temperature. The SiC_f/SiC/Mu composite prepared with 5 wt% PCS/xylene solution showed the maximum dielectric loss value of 0.38 at 10 GHz. Under the dual action of polarization mechanism and conductance loss, both ε′ and ε′′ of the SiC_f/SiC/Mu composites enhanced as the temperature increased. At 700 °C, the corresponding bandwidth (RL ≤ ?5 dB) of SiC_f/SiC/Mu composites prepared with 5 wt% PCS/xylene solution can reach 3.3 GHz at 2.6 mm. The SiC_f/SiC/Mu composite with SiC interphase prepared with 5 wt% PCS/xylene solution is expected to be an excellent structural-functional material.