Preparation and swelling properties of semi‐IPN hydrogels based on chitosan‐g‐poly(acrylic acid) and phosphorylated polyvinyl alcohol

The phosphorylated poly(vinyl alcohol) (P‐PVA) samples with various substitution degrees were prepared through the esterification reaction of PVA and phosphoric acid. By using chitosan (CTS), acrylic acid (AA) and P‐PVA as raw materials, ammonium persulphate (APS) as an initiator and N,N‐methylenebisacrylamide as a crosslinker, the CTS‐g‐PAA/P‐PVA semi‐interpenetrated polymer network (IPN) ssuperabsorbent hydrogel was prepared in aqueous solution by the graft copolymerization of CTS and AA and followed by an interpenetrating and crosslinking of P‐PVA chains. The hydrogel was characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) techniques, and the influence of reaction variables, such as the substitution degree and content of P‐PVA on water absorbency were also investigated. FTIR and DSC results confirmed that PAA had been grafted onto CTS backbone and revealed the existence of phase separation and the formation of semi‐IPN network structure. SEM observations indicate that the incorporation of P‐PVA induced highly porous structure, and P‐PVA was uniformly dispersed in the polymeric network. Swelling results showed that CTS‐g‐PAA/P‐PVA semi‐IPN superabsorbent hydrogel exhibited improved swelling capability (421 g·g^?1 in distilled water and 55 g·g^?1 in 0.9 wt % NaCl solution) and swelling rate compared with CTS‐g‐PAA/PVA hydrogel (301 g·g^?1 in distilled water and 47 g·g^?1 in 0.9 wt % NaCl solution) due to the phosphorylation of PVA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and properties of porous poly(sodium acrylate‐co‐acrylamide) salt‐resistant superabsorbent composite

A novel semi‐interpenetrating polymer networks (semi‐IPNs) porous salt‐resistant superabsorbent composite was prepared by copolymerization of partially neutralized acrylic acid and acrylamide using polyethylene glycol as semi‐IPNs composite, N,N′‐methylenebisacrylamide, triene propanol phosphate, and trihydroxymethyl propane glycidol ether as crosslinking agents, methanol, propanol, and butanol as foaming agents, and L ‐ascorbic acid and peroxide hydrogen as initiators. To improve the properties of swollen hydrogel, such as strength, resilience, permeabilities, and dispersion, the copolymer was surface‐crosslinked, and then blended with aluminum sulfate, sodium carbonate, and sodium 1‐octadecanol phosphate in the course of post treatment. The influences of reaction conditions on properties of superabsorbent composite were investigated and optimized, and the water absorbency of superabsorbent composite prepared at optimal conditions in 0.9 wt% NaCl aqueous solution under atmospheric pressure and certain load (P ≈ 2 × 10³ Pa) were 61 g g^?1 and 16.7 g g^?1, respectively. Moreover, the swelling rate reached 22.003 × 10^?3 g (g s)^?1. And the excellent hydrogel properties, such as hydrogel strength, resilience, permeabilities, and dispersion were also obtained. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Preparation and characterization of polyvinyl alcohol based biomaterials: Water sorption and in vitro blood compatibility study

Semi‐interpenetrating polymer networks (semi‐IPNs) based on polyvinyl alcohol (PVA) and crosslinked polyacrylamide (PAM) were prepared by redox polymerization and further characterized by FTIR, ESEM, and XRD techniques. The semi‐IPNs of varying compositions were investigated for their water sorption behavior, and the network parameters like average molecular weight between crosslinks (M_C) and crosslink density were evaluated from water imbibition measurements. The semi‐IPNs were also judged for their in vitro blood compatibility by blood clot formation and percent hemolysis test. It was noticed that the chemical architecture exert a profound effect on the over all performance of the biomaterials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2402–2408, 2006     

Acrylic superabsorbents: a meticulous investigation on copolymer composition and modification

In this paper, a six-factor and five-level orthogonal test was designed to investigate the influence factors on the solution absorbency of poly(acrylic acid-co-acrylamide) super absorbent resin (PAA/AM SAR). The results showed that the mass ratio of AA to AM played a predominant role in the synthesis of high-performance SAR. The copolymer composition $\overline{{F_{1} }}$ was 0.625 for the optimal absorbency copolymer. To control the copolymer composition, the reactivity ratios of AA and AM, which were 0.365 and 0.753, respectively, were determined at 60 °C using the integral method. The concentration of residual monomers was measured by ultraviolet spectrophotometry (UV) and gas chromatography (GC) methods. The copolymer composition was controlled by molar fraction of monomer AA $\mathop f\nolimits_{1}^{0}$  = 0.64, monomer conversion at 80–90 % and copolymerization at 60 °C. To improve the solution absorbency and water retention, PAA/AM SAR was modified by polyvinyl alcohol (PVA), cellulose and kaolin clay (KC). It is worth noting that the sample modified by the feed AA and AM PVA significantly increased the deionized water absorbency to 1,617 g/g and KC enhanced the 0.9 wt% NaCl absorbency to 189 g/g, which were higher than those of the commercial products. The chemical structure of copolymers was characterized by carbon-13 nuclear magnetic resonance spectroscopy (¹³C NMR) and fourier transform infrared spectrum (FTIR) and their pore morphology was investigated by scanning electron microscope (SEM).     

Swelling behavior of semi‐interpenetrating polymer network hydrogels composed of poly(vinyl alcohol) and poly(acrylamide‐co‐sodium methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐sodium methacrylate) poly(AAm‐co‐SMA) were prepared by the semi IPN method. These IPN hydrogels were prepared by polymerizing aqueous solution of acrylamide and sodium methacrylate, using ammonium persulphate/N,N,N¹,N¹‐tetramethylethylenediamine (APS/TMEDA) initiating system and N,N¹‐methylene‐bisacrylamide (MBA) as a crosslinker in the presence of a host polymer, poly(vinyl alcohol). The influence of reaction conditions, such as the concentration of PVA, sodium methacrylate, crosslinker, initiator, and reaction temperature, on the swelling behavior of these IPNs was investigated in detail. The results showed that the IPN hydrogels exhibited different swelling behavior as the reaction conditions varied. To verify the structural difference in the IPN hydrogels, scanning electron microscopy (SEM) was used to identify the morphological changes in the IPN as the concentration of crosslinker varied. In addition to MBA, two other crosslinkers were also employed in the preparation of IPNs to illustrate the difference in their swelling phenomena. The swelling kinetics, equilibrium water content, and water transport mechanism of all the IPN hydrogels were investigated. IPN hydrogels being ionic in nature, the swelling behavior was significantly affected by environmental conditions, such as temperature, ionic strength, and pH of the swelling medium. Further, their swelling behavior was also examined in different physiological bio‐fluids. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 302–314, 2005     

Swelling and diffusion characteristics of novel semi‐interpenetrating network hydrogels composed of poly[(acrylamide)‐ co‐(sodium acrylate)] and poly[(vinylsulfonic acid), sodium salt]

A series of novel semi‐interpenetrating polymer networks (IPNs) composed of poly[(acrylamide)‐co‐(sodium acrylate)] with varying amounts (5, 10, and 15 wt%) of poly[(vinylsulfonic acid), sodium salt] was synthesized. The semi‐IPN hydrogels were characterized by infrared spectroscopy. The swelling behavior of these IPNs was studied in distilled water/physiological solutions/buffer solutions/salt solutions. As the amount of poly[(vinylsulfonic acid), sodium salt] increased in the network, the swelling capacity of the semi‐IPNs increased considerably. The swelling and diffusion characteristics such as water penetration velocity (v), diffusion exponent (n), and diffusion coefficient (D) were calculated in distilled water, as well as in other physiological solutions. The highest swelling capacity was noted in urea and glucose solutions. The semi‐IPN hydrogels followed non‐Fickian diffusion behavior in water and physiological fluids, whereas Fickian behavior was observed in buffer solutions. The stimuli‐responsive characteristics towards physiological fluids, salt concentration, and temperature of these semi‐IPN hydrogels were also investigated. The swelling behavior of the semi‐IPNs decreased markedly with an increase of the concentration of the salt solutions. Copyright © 2006 Society of Chemical Industry     

Synthesis of AA‐based superabsorbent interpenetrated with sodium PVA sulfate

An interpenetrating network of acrylic acid (AA)‐based superabsorbents and sodium PVA sulfate (SPS) were prepared by copolymerizing AA and N,N′‐methylene bisacrylamide as a crosslinking monomer in a solution of SPS with KPS, a radical initiator. The SPS was prepared through the sulfation of the hydroxyl groups of PVA with DMF‐SO₃ complex in DMSO. The AA‐based superabsorbent interpenetrated with SPS (SA‐IP‐SPS) showed superior properties such as higher water and saline absorbency, absorbency under load (AUL), and water retention value (WRV) compared with AA‐based superabsorbent due to the interpenetrated SPS. The maximum water and saline absorbency of SA‐IP‐SPS was 1753 and 125.6 g/g, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2525–2532, 2000     

Synthesis and Swelling Behavior of Superabsorbents Cross-Linked with N-Maleyl Chitosan

A kind of superabsorbent based on the monomers maleic anhydride (MA) and acrylic acid (AA) was prepared by solution polymerization using ammonium peroxodisulfate (AP) and sodium bisulfite (NaHSO₃) as initiator, and N-maleyl chitosan (N-MACH) as cross-linker. Effects of process parameters such as the amount of cross-linker, mass ratio of MA to AA, and neutralization degree of AA on the water absorbency of superabsorbents are discussed. The results indicated the water absorbency of superabsorbents increased and then decreased with the increase of MA content, the amount of the N-MACH cross-linker, and the neutralization degree of AA. Under the optimal conditions, the water absorbency of superabsorbents could reach l560.42 g/g and 83.7 g/g in distilled water and in 0.9% NaCl solution, respectively. In addition, to enhance the water absorbency of superabsorbents in 0.9% NaCl solution, polyvinyl alcohol (PVA) was introduced as interpenetrating polymer in the network and 2-acrylamido-2-methyl propane sulfonic acid (AMPS) was introduced as comonomer. It was proved that PVA and AMPS could effectively improve the water absorbency of superabsorbents both in distilled water and 0.9% NaCl solution.     

Synthesis,characterization and swelling behaviors of hydroxyethyl cellulose‐g‐poly(acrylic acid)/attapulgite superabsorbent composite

In this work, a series of novel hydroxyethyl cellulose‐ g‐poly(acrylic acid)/attapulgite (HEC‐g‐PAA/APT) superabsorbent composites were prepared through the graft polymerization of hydroxyethyl cellulose (HEC), partially neutralized acrylic acid (AA), and attapulgite (APT) in aqueous solution, and the composites were characterized by means of Fourier‐transform spectroscopy, scanning electron microscopy, and transmission electronmicroscopy. The effects of polymerization variables including concentrations of the initiator and crosslinker and APT content on water absorbency were studied, and the swelling properties in various pH solutions as well as the swelling kinetics in various saline solutions were also systematically evaluated. Results showed that the introduction of 5 wt% APT into HEC‐g‐PAA polymeric network could improve both water absorbency and water absorption rate of the superabsorbent composites. In addition, the superabsorbent composites retained high water absorbency over a wide pH range of 4–10, and the swelling kinetics of the superabsorbent composites in CaCl₂ and FeCl₃ solutions exhibited a remarkable overshooting phenomenon. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Thermal characterizations of semi‐interpenetrating polymer networks composed of poly(ethylene oxide) and poly(N‐isopropylacrylamide)

Poly(N‐isopropylacrylamide) (PNIPAAm)/poly(ethylene oxide) (PEO) semi‐interpenetrating polymer networks (semi‐IPNs) synthesized by radical polymerization of N‐isopropylacrylamide (NIPAAm) in the presence of PEO. The thermal characterizations of the semi‐IPNs were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). The melting temperature (T_m) of semi‐IPNs appeared at around 60°C using DSC. DEA was employed to ascertain the glass transition temperature (T_g) and determine the activation energy (E_a) of semi‐IPNs. From the results of DEA, semi‐IPNs exhibited one T_g indicating the presence of phase separation in the semi‐IPN, and T_gs of semi‐IPNs were observed with increasing PNIPAAm content. The thermal decomposition of semi‐IPNa was investigated using TGA and appeared at around 370°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3922–3927, 2003     

羽毛蛋白接枝聚丙烯酸-丙烯酰胺树脂的合成与吸水性能

以改性羽毛蛋白(MFP)、丙烯酸（AA）和丙烯酰胺(AM)为主要原料,N,N′-亚甲基双丙烯酰胺为交联剂,硫酸钾-亚硫酸氢钠为引发剂,采用溶液聚合法制备了羽毛蛋白接枝聚丙烯酸-丙烯酰胺高吸水树脂［P(MFP-g-AA/AM)］,并对其吸水性能及其影响因素进行了考察。结果表明,P(MFP-g-AA/AM)制备的最适宜工艺条件为W_AA∶W_AM=70∶30,丙烯酸的中和度为90％,W_MFP∶W_AA+AM=10%,W_initiator∶W_AA+AM=0.8%,W_crosslinker∶W_AA+AM=0.10%,反应温度为60℃,反应时间为2 h。在此条件下合成的P(MFP-g-AA/AM)树脂在去离子水中的饱和吸水倍率为578.0 g•g^-1,吸盐水（0.9％NaCl）倍率为78.6 g•g^-1,吸人工尿液倍率为75.1 g•g^-1,均高于羽毛蛋白接枝丙烯酸树脂。     

Development and evaluation of pH-dependent interpenetrating network of acrylic acid/polyvinyl alcohol

The objective of the present work was to synthesize interpenetrating networks (IPNs) of acrylic acid/polyvinyl alcohol (AA/PVA) by free radical polymerization using N,N-methylenebisacrylamide (MBAAm) and glutaraldehyde as cross-linkers. The IPNs were evaluated for swelling, diffusion coefficient and network parameters by using Flory–Huggins theory, i.e., the average molecular weight between cross-links (M _c), polymer volume fraction in swollen state (V _2,s), number of repeating units between cross-links (M _r) and cross-linking density (N). It was found that the degree of swelling of AA/PVA interpenetrating network increases greatly within the pH range 5–7 depending on composition. The gel fraction and porosity increased by increasing the concentration of AA or PVA, while by increasing the degree of cross-linking, porosity decreased and gel fraction increased. Selected samples were loaded with chlorpheniramine maleate as a model drug. Drug release was studied in USP, hydrochloric acid buffer solution of pH 1.2 and phosphate buffer solutions of pH 5.5 and 7.5. Drug release data were fitted into various kinetics models, e.g., zero-order, first-order, Higuchi and Peppas models. The results of the kinetics investigation showed that the drug release from IPNs followed non-Fickian diffusion. Fourier transform infrared spectra confirmed the formation of cross-linked IPNs as there was a shifting to lower frequency of 1,713–1,718 cm^?1 with reduced intensity, while scanning electron microscopy revealed uniform distribution of drug in IPNs.     

Synthesis and characterization of polyacrylamide‐grafted sodium alginate copolymeric membranes and their use in pervaporation separation of water and tetrahydrofuran mixtures

Polyacrylamide‐grafted sodium alginate (PAAm‐g‐Na‐Alg) copolymeric membranes have been prepared, characterized, and used in the pervaporation separation of 10–80 mass % water‐containing tetrahydrofuran mixtures. Totally three membranes were prepared: (1) neat Na‐Alg with 10 mass % of polyethylene glycol (PEG) and 5 mass % of polyvinyl alcohol (PVA), (2) 46 % grafted PAAm‐g‐Na‐Alg membrane containing 10 mass % of PEG and 5 mass % of PVA, and (3) 93 % grafted PAAm‐g‐Na‐Alg membrane containing 10 mass % of PEG and 5 mass % of PVA. Using the transport data, important parameters like permeation flux, selectivity, pervaporation separation index, swelling index, and diffusion coefficient have been calculated at 30°C. Diffusion coefficients were also calculated from sorption gravimetric data of water–tetrahydrofuran mixtures using Fick's equation. Arrhenius activation parameters for the transport processes were calculated for 10 mass % of water in the feed mixture using flux and diffusion data obtained at 30, 35, and 40°C. The separation selectivity of the membranes ranged between 216 and 591. The highest permeation flux of 0.677 kg/m² h was observed for 93% grafted membrane at 80 mass % of water in the feed mixture. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 272–281, 2002     

Semiinterpenetrating polymer networks based on polyurethane and polyvinylpyrrolidone. I. Thermodynamic state and dynamic mechanical analysis

Semiinterpenetrating polymer networks (semi‐IPNs) based on polyurethane (PU) and polyvinylpyrrolidone (PVP) have been synthesized, and their thermodynamic characteristics, thermal properties, and dynamical mechanical properties have been studied to have an insight in their structure as a function of their composition. First, the free energies of mixing of the two polymers in semi‐IPNs based on crosslinked PU and PVP have been determined by the vapor sorption method. It was established that these constituent polymers are not miscible in the semi‐IPNs. The differential scanning calorimetry results evidence the T_g of polyurethane and two T_g for PVP. The dynamic mechanical behavior of the semi‐IPNs has been investigated and is in accordance with their thermal behavior. It was shown that the semi‐IPNs present three distinct relaxations. If the temperature position of PU maximum tan δ is invariable, on the contrary, the situation for the two maxima observed for PVP is more complex. Only the maximum of the highest temperature relaxation is shifted to lower temperature with changing of the semi‐IPNs composition. It was concluded that investigated semi‐IPNs are two‐phase systems with incomplete phase separation. The phase composition was calculated using viscoelastic properties. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 852–862, 2001     

Synthesis and characterization of semi‐interpenetrating networks based on poly(dimethylsiloxane) and poly(vinyl alcohol)

Semi‐interpenetrating networks (Semi‐IPNs) with different compositions were prepared from poly(dimethylsiloxane) (PDMS), tetraethylorthosilicate (TEOS), and poly(vinyl alcohol) (PVA) by the sol‐gel process in this study. The characterization of the PDMS/PVA semi‐IPN was carried out using Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and swelling measurements. The presence of PVA domains dispersed in the PDMS network disrupted the network and allowed PDMS to crystallize, as observed by the crystallization and melting peaks in the DSC analyses. Because of the presence of hydrophilic (? OH) and hydrophobic (Si? (CH₃)₂) domains, there was an appropriate hydrophylic/hydrophobic balance in the semi‐IPNs prepared, which led to a maximum equilibrium water content of ～ 14 wt % without a loss in the ability to swell less polar solvents. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Poly[(N‐isopropylacrylamide)‐co‐(itaconic acid)] hydrogels with poly(ethylene glycol)

The aim of the work reported here was to investigate temperature‐ and pH‐sensitive hydrogels of N‐isopropylacrylamide (NIPAM) and itaconic acid (IA) and their semi‐interpenetrating polymer networks (semi‐IPNs) with varying contents of poly(ethylene glycol) (PEG). The stimuli responsiveness, swelling behaviour and mechanical properties of the hydrogels and semi‐IPNs were studied in order to investigate the effect of various amounts of PEG. Pulsed‐gradient spin‐echo NMR experiments were carried out to investigate the diffusion process. The pH sensitivity increased with an increasing amount of PEG in the semi‐IPNs, while the overall rate of water uptake was diffusion‐controlled (n < 0.5). For certain PEG contents (5 and 10 wt%), the semi‐IPNs exhibited better mechanical properties than the poly(NIPAM‐co‐IA) copolymer. The calculated values of the self‐diffusion coefficients of water indicated facilitated diffusion of water through the system with increased amounts of PEG, while the self‐diffusion coefficients of a model compound, metoprolol tartrate, showed no significant dependence on the amount of PEG. According to the results obtained and compared to results reported in the literature, the investigated semi‐IPNs may have potential applications in the controlled release of macromolecular active agents such as proteins and peptides. Copyright © 2009 Society of Chemical Industry     

Study on superabsorbent composite. XX. Effects of cation‐exchanged montmorillonite on swelling properties of superabsorbent composite containing sodium humate

In this work, the effects of different cation‐exchanged montmorillonite on water absorbency of poly(acrylic acid‐co‐acrylamide)/montmorillonite/sodium humate (PAA‐AM/MMT/SH) superabsorbent composite were systematically investigated under the same preparation conditions. The superabsorbents doped with different cation‐exchanged montmorillonite were characterized by Fourier‐transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy technologies. Swelling behaviors of developing superabsorbent composite in various cationic saline solutions (NaCl, CaCl₂, and FeCl₃) were also investigated. The water absorbencies of superabsorbent composite with 20 wt% MMT and 30 wt% SH are 638, 723, 682, and 363 g g⁻¹ in distilled water for incorporating natural Na⁺‐MMT, Li⁺‐exchanged MMT, Ca²⁺‐exchanged MMT, and Al³⁺‐exchanged MMT, respectively. The results showed that the cation‐exchange process had some obvious influences on final water absorbency of superabsorbent composite. NaCl, CaCl₂, and FeCl₃ solutions did not alter the swelling characteristics of the superabsorbent materials at a concentration of less than 0.01 mM, however, a concentration of greater than 0.1 mM caused a collapse in the swelling curves. The excellent swelling‐reswelling‐swelling behavior and lower swelling rate testified that Al³⁺‐exchanged MMT can act as an assistant crosslinker in the polymeric network. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Superabsorbent composite. XIII. Effects of Al3+‐attapulgite on hydrogel strength and swelling behaviors of poly(acrylic acid)/Al3+‐attapulgite superabsorbent composites

Al³⁺‐attapulgite (Al³⁺‐APT) was prepared by treating attapulgite (APT) with AlCl₃ aqueous solution of various concentrations. The poly(acrylic acid)/Al³⁺‐attapulgite (PAA/Al³⁺‐APT) superabsorbent composite was prepared by reaction of partly neutralized acrylic acid, and Al³⁺‐APT in aqueous solution using N, N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The surface morphology of the composite was investigated by SEM, and the Al³⁺‐APT composite generated a relatively planar surface comparing the nature APT. The effects of Al³⁺‐APT on hydrogel strength and swelling behaviors, such as equilibrium water absorbency, swelling rate, and reswelling capability, of the superabsorbent composites were also studied. The hydrogel strength and reswelling capability were improved, however, the equilibrium water absorbency and swelling rate decreased with increasing AlCl₃ solution concentration. The equilibrium water absorbency firstly increased, and then decreased with increasing Al³⁺‐APT content. The results indicate that Al³⁺‐APT acts as an assistant crosslinker in the polymeric network, which has great influences on hydrogel strength and swelling behaviors of the PAA/Al³⁺‐APT superabsorbent composites. POLYM. ENG. SCI., 47:619–624, 2007. © 2007 Society of Plastics Engineers.     

Synthesis of full and semi Interpenetrating hydrogel from polyvinyl alcohol and poly (acrylic acid‐co‐hydroxyethylmethacrylate) copolymer: Study of swelling behavior,network parameters,and dye uptake properties

Semi and full interpenetrating network (IPN) hydrogels were synthesized by allowing free radical copolymerization of acrylic acid (AA) and hydroxyethyl methacrylate (HEMA) in the matrix of polyvinyl alcohol (PVOH). Accordingly, four different semi IPN hydrogels were prepared with PVOH: copolymer mass ratio of 1 : 1, 1 : 0.75, 1 : 0.5, and 1 : 0.25. These hydrogels were designated as SEMIIPN1, SEMIIPN2, SEMIIPN3, and SEMIIPN4, respectively. In all of these SEMIIPN, after polymerization PVOH was crosslinked with 2 mass % glutaraldehyde to form the semi IPN structure. In a similar way, sequential full IPN were prepared from PVOH and copolymer of AA and HEMA (designated as PAAHEMA) with same composition except in this case apart from crosslinking of PVOH by 2 mass % glutaraldehyde the PAAHEMA copolymer was further crosslinked with N,N′‐methylenebisacrylamide (NMBA) to produce four full IPN hydrogels designated as FULLIPN1, FULLIPN2, FULLIPN3, and FULLIPN4. All of these semi and full IPN type hydrogels were characterized by carboxylic %, FTIR, UV, DTA‐TGA, XRD, SEM, and mechanical properties. The network parameters, swelling and diffusion characteristics of these hydrogels were also studied. The performance of these semi and full IPNs were compared in terms of their relative abilities for removing varied concentration of rhodamine B (RB) and methyl Violet (MV) dyes from water. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Gellan gum‐based novel composite hydrogel: Evaluation as adsorbent for cationic dyes

A semi‐interpenetrating network system [(GG‐g‐PAAm)‐PVA] was made by microwave irradiation of aqueous mixture of gellan gum (GG), acrylamide (AAm), and poly(vinyl alcohol) (PVA) containing N,N′‐methylene‐bis‐acrylamide as crosslinking agent. The gel was characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, and scanning electron microscopy techniques. The swelling behavior was studied under different pH conditions. A pH‐dependent swelling with maximum swelling under neutral pH was observed. The swelling process is found to follow second‐order kinetics and the mechanism of water transport is found to be Fickian type of diffusion. The (GG‐g‐PAAm)‐PVA was evaluated for removal of dye from aqueous solution, using crystal violet, a cationic dye. The maximum adsorption capacity of the gel was found to be 45.45 mg/g. The kinetic studies revealed a second‐order adsorption process which fits well into Langmuir model. The evaluation of thermodynamic parameters indicated the adsorption process to be exothermic and spontaneous at lower temperatures. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45527.