Superabsorbent composite. XIII. Effects of Al3+‐attapulgite on hydrogel strength and swelling behaviors of poly(acrylic acid)/Al3+‐attapulgite superabsorbent composites

Al³⁺‐attapulgite (Al³⁺‐APT) was prepared by treating attapulgite (APT) with AlCl₃ aqueous solution of various concentrations. The poly(acrylic acid)/Al³⁺‐attapulgite (PAA/Al³⁺‐APT) superabsorbent composite was prepared by reaction of partly neutralized acrylic acid, and Al³⁺‐APT in aqueous solution using N, N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The surface morphology of the composite was investigated by SEM, and the Al³⁺‐APT composite generated a relatively planar surface comparing the nature APT. The effects of Al³⁺‐APT on hydrogel strength and swelling behaviors, such as equilibrium water absorbency, swelling rate, and reswelling capability, of the superabsorbent composites were also studied. The hydrogel strength and reswelling capability were improved, however, the equilibrium water absorbency and swelling rate decreased with increasing AlCl₃ solution concentration. The equilibrium water absorbency firstly increased, and then decreased with increasing Al³⁺‐APT content. The results indicate that Al³⁺‐APT acts as an assistant crosslinker in the polymeric network, which has great influences on hydrogel strength and swelling behaviors of the PAA/Al³⁺‐APT superabsorbent composites. POLYM. ENG. SCI., 47:619–624, 2007. © 2007 Society of Plastics Engineers.     

Swelling study of superabsorbent PAA‐co‐PAM/clay nanohydrogel

A series of superabsorbent composites were prepared from acrylic acid (AA), acrylamide (AM), and Cloisite® 30B by aqueous solution polymerization technique using ammonium peroxodisulfate (APS) as initiator. The interaction of the organically modified nanoclay with PAA‐co‐PAM copolymer was verified by FTIR, whereas the morphology of the composite was studied by Scanning Electron Microscopy (SEM). The water absorbency in deionized water and saline water of the synthesized nanohydrogels was measured by calculating their percentage swelling ratio. The effects of copolymerization, monomer ratio, clay content, and temperature on the water absorbency were studied. The results indicated a considerable increase in swelling ratio by proper monomer proportion and incorporation of optimum clay percentage into the copolymer matrix. It was found that the nanohydrogel acquired highest water absorbency with 2% clay loading. The reswelling ability and water retention capacity of the PAA‐co‐PAM hydrogel and PAA‐co‐PAM/clay nanohydrogel were also measured. The water absorbency was found to increase after each reswelling for which it may be useful as recyclable superabsorbent material. The results of water retention capacity of the nanohydrogel were also encouraging and find application in agriculture, especially in drought‐prone areas. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of starch‐g‐Poly(acrylic acid)/Organo‐Zeolite 4A superabsorbent composites with respect to their water‐holding capacities and nutrient‐release behavior

Novel superabsorbent composites were prepared using starch, acrylic acid, and organo‐zeolite 4A micropowder via aqueous solution graft copolymerization. The effects of organo‐zeolite 4A content on water absorbency were tested to determine the optimum conditions that ensure a high swelling ability. Under these conditions, the maximum swelling ability in distilled water was determined to be 511 g/g when the amount of organo‐zeolite 4A in the feed was 10 wt%. The prepared samples were characterized with Fourier transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscope (SEM). The SEM characterization of the samples indicated that the superabsorbent composites had more pores and water than zeolite‐free superabsorbents. The swelling capacities in distilled water, various salt solutions, and aqueous urea were studied. The on–off switching behavior and the release of urea from the loaded starch‐g‐ poly(acrylic acid)/organo‐zeolite 4A were also determined. The results indicated that the novel composite was responsive to salts and exhibited on–off switching behavior, as evidenced by reversible swelling and de‐swelling. In addition, the slow nutrient release makes this material suitable for many potential applications in the fields of agriculture and horticulture. POLYM. COMPOS., 38:1838–1848, 2017. © 2015 Society of Plastics Engineers     

Preparation and properties of porous poly(sodium acrylate‐co‐acrylamide) salt‐resistant superabsorbent composite

A novel semi‐interpenetrating polymer networks (semi‐IPNs) porous salt‐resistant superabsorbent composite was prepared by copolymerization of partially neutralized acrylic acid and acrylamide using polyethylene glycol as semi‐IPNs composite, N,N′‐methylenebisacrylamide, triene propanol phosphate, and trihydroxymethyl propane glycidol ether as crosslinking agents, methanol, propanol, and butanol as foaming agents, and L ‐ascorbic acid and peroxide hydrogen as initiators. To improve the properties of swollen hydrogel, such as strength, resilience, permeabilities, and dispersion, the copolymer was surface‐crosslinked, and then blended with aluminum sulfate, sodium carbonate, and sodium 1‐octadecanol phosphate in the course of post treatment. The influences of reaction conditions on properties of superabsorbent composite were investigated and optimized, and the water absorbency of superabsorbent composite prepared at optimal conditions in 0.9 wt% NaCl aqueous solution under atmospheric pressure and certain load (P ≈ 2 × 10³ Pa) were 61 g g^?1 and 16.7 g g^?1, respectively. Moreover, the swelling rate reached 22.003 × 10^?3 g (g s)^?1. And the excellent hydrogel properties, such as hydrogel strength, resilience, permeabilities, and dispersion were also obtained. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Preparation and swelling properties of semi‐IPN hydrogels based on chitosan‐g‐poly(acrylic acid) and phosphorylated polyvinyl alcohol

The phosphorylated poly(vinyl alcohol) (P‐PVA) samples with various substitution degrees were prepared through the esterification reaction of PVA and phosphoric acid. By using chitosan (CTS), acrylic acid (AA) and P‐PVA as raw materials, ammonium persulphate (APS) as an initiator and N,N‐methylenebisacrylamide as a crosslinker, the CTS‐g‐PAA/P‐PVA semi‐interpenetrated polymer network (IPN) ssuperabsorbent hydrogel was prepared in aqueous solution by the graft copolymerization of CTS and AA and followed by an interpenetrating and crosslinking of P‐PVA chains. The hydrogel was characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) techniques, and the influence of reaction variables, such as the substitution degree and content of P‐PVA on water absorbency were also investigated. FTIR and DSC results confirmed that PAA had been grafted onto CTS backbone and revealed the existence of phase separation and the formation of semi‐IPN network structure. SEM observations indicate that the incorporation of P‐PVA induced highly porous structure, and P‐PVA was uniformly dispersed in the polymeric network. Swelling results showed that CTS‐g‐PAA/P‐PVA semi‐IPN superabsorbent hydrogel exhibited improved swelling capability (421 g·g^?1 in distilled water and 55 g·g^?1 in 0.9 wt % NaCl solution) and swelling rate compared with CTS‐g‐PAA/PVA hydrogel (301 g·g^?1 in distilled water and 47 g·g^?1 in 0.9 wt % NaCl solution) due to the phosphorylation of PVA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Utilization of waste polystyrene and starch for superabsorbent composite preparation

A superabsorbent composed of waste polystyrene, starch, and acrylic acid was prepared through emulsion polymerization. The effects of major factors such as starch, acrylic acid, initiator, crosslinker, and bentonite contents and the neutralization degree of acrylic acid on water absorbency were investigated to obtain optimum conditions with high swelling capacity. The superabsorbent hydrogel was characterized by scanning electron microscope (SEM), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA). The FTIR results confirmed that the grafting polymerization took place among the polystyrene, acrylic acid, starch, and bentonite. The introduction of bentonite particles into the polystyrene‐g‐poly (acrylic acid)‐co‐starch system could increase the water absorbency. The superabsorbent composite containing 3 wt % bentonite had the highest water absorbency (500 g/g in distilled water and 49 g/g in 0.9 wt % NaCl solution). © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of poly(acrylic acid‐co‐acrylamide)/kaolin and release kinetics of urea from it

A series of poly(acrylic acid‐co‐acrylamide)/kaolin [poly(AA‐co‐Am)/kaolin] composites were prepared by aqueous solution copolymerization of partially neutralized acrylic acid and acrylamide in the presence of kaolin nanopowder, which was synthesized to act as a release carrier of urea fertilizer. The superabsorbent composite was swollen in aqueous solution of urea to load urea, and the effect of urea concentration on the swelling was investigated. Furthermore, the effects of the contents of crosslinker, kaolin, and acrylamide, the neutralization degree of acrylic acid, and temperature, pH, and ionic strength of release medium on water absorbency and diffusion coefficient of urea release from poly(AA‐co‐Am)/kaolin were studied systematically. It was found that urea loading percentage could be adjusted by urea concentration of swelling medium, and urea diffusion coefficient could be regulated through the contents of crosslinker, kaolin, and acrylamide, and the neutralization degree of acrylic acid. Additionally, temperature and ionic strength of release medium may also affect the urea release process. The conclusions obtained could provide theoretical basis for urea diffusion behavior in superabsorbent used in agriculture. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Poly(acrylamide‐co‐vinyl alcohol)—Superabsorbent materials reinforced by modified clay

A series of copolymeric superabsorbent materials comprising polyacrylamide (PAM), polyvinyl alcohol (PVA) reinforced with variable wt% of modified clay were prepared. The copolymer/clay composite was characterized by Fourier transformed infrared, transmission electron microscopy, and scanning electron microscopy. The water absorbencies of poly(acrylamide‐co‐vinyl alcohol)/clay composites were measured by calculating their percentage swelling ratio. The effects of copolymerization, type of clay, and clay content on the water absorbencies were studied. The swelling was measured in acidic, alkaline, and saline condition to ensure its versatility. The results indicated a remarkable increase in swelling ratio by incorporation of modified clay having higher hydrophilicity and optimum clay loading. The poly(acrylamide‐co‐vinyl alcohol)/clay composite hydrogel was found to have better re‐swelling ability and water retention capacity compared to the virgin copolymer. The substantial enhancement of swelling properties enables the superabsorbent poly(acrylamide‐co‐vinyl alcohol)/clay suitable for agricultural and horticultural application. POLYM. COMPOS., 34:1794–1800, 2013. © 2013 Society of Plastics Engineers     

Preparation of chitosan‐g‐poly(acrylamide)/montmorillonite superabsorbent polymer composites: Studies on swelling,thermal, and antibacterial properties

Superabsorbent composites based on chitosan‐g‐poly(acrylamide) and montorillonite (CTS‐g‐PAAm/MMT) were synthesized through in situ radical polymerization by grafting of crosslinked acrylamide onto chitosan backbone in presence of MMT at different contents. The formation of the grafted network was confirmed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR‐FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetery (DSC). The obtained porous structure was observed by scanning electron microscope (SEM). The presence of clay and its interaction with chitosan‐g‐poly(acrylamide) (CTS‐g‐PAAm) matrix was evidenced by ATR‐FTIR analysis. The morphology was investigated by both X‐ray diffraction (XRD) and SEM analyses. It was suggested the formation of mostly exfoliated structures with more porous structures. Besides, the thermal stability of these composites, observed by TGA analysis, was slightly affected by the clay loading as compared to the matrix. These hydrogel composites were also hydrolyzed to achieve anionic hydrogels with ampholytic properties. Swelling behaviors were examined in doubly distilled water, 0.9 wt % NaCl solution and buffer solutions. The water absorbency of all superabsorbent composites was enhanced by adding clay, where the maximum was reached at 5 wt % of MMT. Their hydrolysis has not only greatly optimized their absorption capacity but also improved their swelling rate and salt‐resistant ability. The hydrolyzed superabsorbent showed better pH‐sensitivity than the unhydrolyzed counterparts. The results of the antibacterial activity of these superabsorbents composites against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), assayed by the inhibitory zone tests, have showed moderate inhibition of the bacteria growth. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39747.     

Linear low‐density polyethylene‐g‐poly(acrylic acid)/(organo‐montmorillonite) hydrogel composite as hydrogel electrolytes for zinc–carbon batteries

A hydrogel composite that has been prepared by using waste linear low‐density polyethylene, acrylic acid, and organo‐montmorillonite (LLDPE‐g‐PAA/OMMT) is used as a hydrogel electrolyte. An absorbency test was used to determine the percentage of ZnCl₂ solution absorbed by the hydrogel composite. The swelling behavior of the hydrogel composite in the ZnCl₂ solution was then studied. The highest absorbency was recorded when the concentration of ZnCl₂ solution was 3 M. The conductivity of ZnCl₂‐hydrogel composite electrolytes is dependent on the solution's concentration. A mixture of ZnCl₂ solution with hydrogel composite yields a good hydrogel composite electrolyte with a conductivity of 0.039 S cm^?1 at 3 M ZnCl₂. The hydrogel composite electrolyte was used to produce zinc‐carbon cells. The fabricated cell gives capacity of 7.8 mAh, has an internal resistance of 9.9 Ω, a maximum power density of 15.78 mWcm^?2, and a short‐circuit current density of 43.75 mAcm^?2 for ZnCl₂‐hydrogel composite electrolytes. J. VINYL ADDIT. TECHNOL., 22:279–284, 2016. © 2014 Society of Plastics Engineers     

Superabsorbent composite XXII: Effects of modified sepiolite on water absorbency and swelling behavior of chitosan‐g‐poly(acrylic acid)/sepiolite superabsorbent composite

In this work, a series of chitosan‐g‐poly(acrylic acid)/sepiolite (CTS‐g‐PAA/ST) superabsorbent composites containing raw sepiolite, acid‐activated sepiolite, and cation‐exchanged sepiolite were synthesized by free‐radical graft polymerization in aqueous solution, using N,N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The effects of raw sepiolite, acid‐activated sepiolite, and cation‐exchanged sepoilite on equilibrium water absorbency, swelling rate, and swelling behavior in different pH value solution of superabsorbent composites were systematically investigated. The results from FTIR spectra showed that chitosan and sepiolite participated in graft polymerization reaction with acrylic acid. The introduction of acid‐activated and cation‐exchanged sepiolite into chitosan‐g‐poly(acrylic acid) polymeric network could improve water absorbency and swelling rate compared with that of the raw sepiolite. All prepared samples have similar swelling behavior in different pH solutions and the equilibrium water absorbencies of samples keep roughly constant in the pH range from 4 to 12. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Synthesis and properties of poly(sodium acrylate‐co‐2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid)/attapulgite as a salt‐resistant superabsorbent composite

A novel salt‐resistant superabsorbent composite was prepared by copolymerization of partially neutralized acrylic acid, 2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid (AMPS) and attapulgite (APT). To enhance the swelling rate (SR) of the copolymer, sodium bicarbonate was used as a foaming agent in the course of copolymerization. Furthermore, for improving the properties of swollen hydrogel, such as strength, resilience and dispersion, the copolymer was surface‐crosslinked with glycerine and sodium silicate, and then the surface‐crosslinked copolymer was blended with aluminum sulfate and sodium carbonate in post treatment process. The influences of some reaction conditions, such as amount of AMPS, APT, and initiator, and neutralization degree of acrylic acid on water absorbency in 0.9 wt% NaCl aqueous solution both under atmospheric pressure (WA) and load (WA_P, P ≈ 2 × 10³ Pa) were investigated. In addition, the effect of them on SR was also studied. The WA and WA_P of the superabsorbent composite prepared under optimal conditions in 0.9 wt% NaCl aqueous solution were 52 g·g^?1 and 8 g·g^?1, respectively. Besides, the SR was fast, and it could reach 0.393 mL·(g·s)^?1. Moreover, the swollen hydrogel possessed excellent salt resistance, hydrogel resilience and dispersion. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

Fast‐swelling oxidized starch phosphate–poly(acrylate/acrylamide/2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid) superabsorbent composite

A fast‐swelling superabsorbent composite was prepared by solution polymerization of acrylate, acrylamide, 2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid and oxidized starch phosphate. Ethanol, propyl alcohol, butyl alcohol, and sodium bicarbonate were used as foaming agents to produce fast‐swelling characteristics. The structure of the superabsorbent composite was characterized using Fourier transform infrared spectroscopy (FTIR). The influences of the amount of water, acrylamide, 2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid, oxidized starch phosphate, initiator, and trihydroxymethyl propane glycidol ether, as well as the neutralization degree of acrylic acid on the equilibrium swelling degree and swelling rate of the superabsorbent composite, were investigated. The equilibrium swelling degree of the superabsorbent composite prepared in a 0.9 wt% NaCl aqueous solution was 52 g g^?1, and the swelling rate reached 0.86 mL g^?1 s^?1. The swelling kinetics was also investigated, and the results indicate that swelling of the superabsorbent composites obeys Schott's pseudo second‐order kinetics model. POLYM. ENG. SCI., 56:1267–1274, 2016. © 2016 Society of Plastics Engineers     

Study on superabsorbent composites. IX: Synthesis,characterization and swelling behaviors of polyacrylamide/clay composites based on various clays

A series of clay-based superabsorbent composite from acrylamide (AM) and various clays, such as attapulgite, kaolinite, mica, vermiculate and Na⁺-montmorillonite, was prepared by free-radical aqueous polymerization, using N,N′-methylenebisacrylamide (MBA) as a crosslinker and ammonium persulfate (APS) as an initiator, and then saponified with sodium hydroxide solution. In this paper, the reaction mechanism and thermal stability of the superabsorbent composites incorporated with various clays were characterized by FTIR, XRD and TGA, respectively. The effects of clay kind and clay content on equilibrium water absorbency of these composites were also investigated and compared. In addition, the influences of clay kind on comprehensive swelling behaviors of the PAM/clay superabsorbent composites were studied. The results indicated that the introduced clays could influence physicochemical properties of obtained superabsorbent composites. Mica could improve thermal stability of corresponding superabsorbent composites to the highest degree comparing with the other clays. The PAM/clay superabsorbent composites incorporated with 10 wt% clay of various kinds were all endowed with equilibrium water absorbency of more than 1300 g g⁻¹. The equilibrium water absorbency decreases with increasing clay content and correlates with the kind of clay. Attapulgite-based superabsorbent composite was endowed with higher water absorbency in univalent cationic saline solution, however, the vermiculite- and the kaolinite-based ones acquired the highest water absorbency in CaCl₂ and FeCl₃ aqueous solution, respectively. Moreover, the superabsorbent composites incorporated with Na⁺-montmorillonite have higher swelling rate and that of doped with mica was endowed with higher reswelling capability.     

Synthesis,characterization, and swelling behavior of alginate‐g‐poly(sodium acrylate)/kaolin superabsorbent hydrogel composites

A novel superabsorbent composite based on sodium alginate and the inorganic clay kaolin was synthesized via the graft copolymerization of acrylic acid (AA) in an aqueous medium with methylene bisacrylamide (MBA) as a crosslinking agent and ammonium persulfate (APS) as an initiator. The effects of reaction variables, such as the MBA, AA, and APS concentrations and the alginate/kaolin weight ratio, on the water absorbency of the composite were systematically optimized. Evidence of grafting and kaolin interactions was obtained by a comparison of the Fourier transform infrared spectra of the initial substrates with that of the superabsorbent composite, and the hydrogel structure was confirmed with scanning electron microscopy. The results indicated that with an increasing alginate/kaolin weight ratio, the swelling capacity and gel content increased. The effects of various salt media were also studied, along with the swelling kinetics. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis of poly(AA‐co‐AM) superabsorbent composites by reinforcement of halloysite nanotubes

A novel poly(acrylic acid‐co‐acrylamide)/halloysite nanotubes [PAA‐AM/HNTs] superabsorbent composite was synthesized by free radical polymerization with using HNTs as an inorganic additive. The composite was characterized by Fourier transform infrared spectroscopy, scanning electron microscope, and thermogravimetric analysis. The results revealed that HNTs and PAA‐AM were combined well together to form a porous structure with a pore size of about 10 μm, and HNTs were uniformly distributed in the composite. The thermal stability was improved by adding HNTs in the composite. The influences of contents of initiator and halloysite, neutralization degree of AA, and molar ratio of AM to AA on water absorbency were investigated. The water absorbency and the water retention capacity were improved after adding HNTs into PAA‐AM. The composite containing 10% HNTs had the highest water absorbency of 1276 g/g in distilled water. Moreover, PAA‐AM/HNTs composite also had a high swelling rate within 60 min and could maintain 78% initial swelling capability after five reswelled test. The substantial enhancement of swelling properties enables PAA‐AM/HNTs suitable for numerous practical applications. POLYM. COMPOS., 36:229–236, 2015. © 2014 Society of Plastics Engineers     

Preparation and Swelling Behavior of Fast‐Swelling Superabsorbent Hydrogels Based On Starch‐g‐Poly(acrylic acid‐co‐sodium acrylate)

Summary: A novel fast‐swelling porous superabsorbent hydrogel was prepared by grafting acrylic acid onto corn starch through free‐radical polymerization in aqueous solution using N,N′‐methylenebisacrylamide as a crosslinker, ammonium persulfate as an initiator, sodium dodecyl sulfate and p‐octyl poly(ethylene glycol)phenyl ether as pore‐forming agents. The graft polymerization and surface morphology of the porous superabsorbents were characterized by FTIR and SEM. The results indicate that the porous superabsorbents were endowed with higher equilibrium water absorbency and faster swelling rate (they needed only 10 min to reach 90% of their equilibrium water absorbency) compared with the nonporous superabsorbents. The dewatering method employed had a significant influence on the swelling behavior of the superabsorbents and dewatering agents were useful to preserve the pores formed during the polymerization process.

The equilibrium water absorbency in distilled water, for the porous and non‐porous starch‐g‐poly(acrylic acid‐co‐sodium acrylate) superabsorbent hydrogels dried through different procedures.     

Effect of hydrophobic monomer on the synthesis and swelling behaviour of a collagen‐graft‐poly[(acrylic acid)‐co‐(sodium acrylate)] hydrogel

BACKGROUND: Graft polymerization of vinylic monomers onto natural backbones is an efficient approach for the synthesis of natural‐based superabsorbents. The nature of the monomers will affect the swelling behaviour of the superabsorbents. Here, a novel superabsorbent was synthesized through grafting of acrylic acid onto collagen in the presence of hydrophobic styrene as co‐monomer. Subsequently, the effect of styrene on the swelling behaviour of the superabsorbent was studied. RESULTS: The highly swelling superabsorbent was prepared by introducing styrene into a collagen‐graft‐poly(acrylic acid) hydrogel. By inclusion of styrene monomer, the swelling capacity of the hydrogel was increased; this is discussed according to the network composition. The effect of swelling media (salt solutions and various pH values) was investigated. The results of absorbency under load showed that hydrogels containing phenyl groups exhibit better behaviour; however, by introducing styrene, the rate of water uptake and resistance to water holding under heating was reduced. Scanning electron micrographs of hydrogels revealed a decrease in porosity on using styrene. CONCLUSION: Inclusion of styrene monomer in the ionic superabsorbent caused high swelling capacity with better absorbency under load. This can be used to prepare highly swelling superabsorbents with good mechanical properties. The pH reversibility of the synthesized superabsorbent makes it a candidate for use in the controlled release of drugs and in agrochemicals. Copyright © 2008 Society of Chemical Industry     

Swelling,thermal stability,antibacterial properties enhancement on composite hydrogel synthesized by chitosan-acrylic acid and ZnO nanowires

ABSTRACT

A series of antibacterial superabsorbents containing zinc oxide nanowires (ZnO NWs) based on chitosan (CS) and acrylic acid (AA) were prepared by one-step synthesis. Antibacterial influence of the content with ZnO NWs complex in superabsorbents on Escherichia coli and Staphylococcus aureus was studied, as well as water absorbency, swelling behavior, and thermal stability. Results showed that water absorbency for CS-co-AA composite hydrogel in water was 1000 g/g, because of the presence of ZnO NWs within CS-co-AA hydrogel facilitated the water absorbency ability. Furthermore, results also showed that the antibacterial effect of CS-co-AA composite hydrogels increased with an increase of ZnO NWs content.     

Synthesis,characterization and swelling behaviors of hydroxyethyl cellulose‐g‐poly(acrylic acid)/attapulgite superabsorbent composite

In this work, a series of novel hydroxyethyl cellulose‐ g‐poly(acrylic acid)/attapulgite (HEC‐g‐PAA/APT) superabsorbent composites were prepared through the graft polymerization of hydroxyethyl cellulose (HEC), partially neutralized acrylic acid (AA), and attapulgite (APT) in aqueous solution, and the composites were characterized by means of Fourier‐transform spectroscopy, scanning electron microscopy, and transmission electronmicroscopy. The effects of polymerization variables including concentrations of the initiator and crosslinker and APT content on water absorbency were studied, and the swelling properties in various pH solutions as well as the swelling kinetics in various saline solutions were also systematically evaluated. Results showed that the introduction of 5 wt% APT into HEC‐g‐PAA polymeric network could improve both water absorbency and water absorption rate of the superabsorbent composites. In addition, the superabsorbent composites retained high water absorbency over a wide pH range of 4–10, and the swelling kinetics of the superabsorbent composites in CaCl₂ and FeCl₃ solutions exhibited a remarkable overshooting phenomenon. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers