Polystyrene composites of single‐walled carbon nanotubes‐graft‐polystyrene

Single‐walled carbon nanotubes (SWCNTs) dispersed in N‐methylpyrrolidone (NMP) were functionalized by addition of polystyryl radicals from 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐ended polystyrene (SWCNT‐g‐PS). The amount of polystyrene grafted to the nanotubes was in the range 20‐25 wt% irrespective of polystyrene number‐average molecular weight ranging from 2270 to 49 500 g mol^?1. In Raman spectra the ratios of D‐band to G‐band intensity were similar for all of the polystyrene‐grafted samples and for the starting SWCNTs. Numerous near‐infrared electronic transitions of the SWCNTs were retained after polymer grafting. Transmission electron microscopy images showed bundles of SWCNT‐g‐PS of various diameters with some of the polystyrene clumped on the bundle surfaces. Composites of SWCNT‐g‐PS in a commercial‐grade polystyrene were prepared by precipitation of mixtures of the components from NMP into water, i.e. the coagulation method of preparation. Electrical conductivities of the composites were about 10^?15 S cm^?1 and showed no percolation threshold with increasing SWCNT content. The glass transition temperature (T_g) of the composites increased at low filler loadings and remained constant with further nanotube addition irrespective of the length and number of grafted polystyrene chains. The change of heat capacity (ΔC_p) at T_g decreased with increasing amount of SWCNT‐g‐PS of 2850 g mol^?1, but ΔC_p changed very little with the amount of SWCNT‐g‐PS of higher molecular weight. The expected monotonic decrease in ΔC_p coupled with the plateau behavior of T_g suggests there is a limit to the amount that T_g of the matrix polymer can increase with increasing amount of nanotube filler. Copyright © 2012 Society of Chemical Industry     

Fabrication of poly(methyl methacrylate)‐block‐poly(N‐isopropylacrylamide) amphiphilic diblock copolymer on silicon substrates via surface‐initiated reverse iodine transfer polymerization

Amphiphilic diblock copolymer on silicon substrates were synthesized via surface‐initiated reverse iodine transfer polymerization (RITP) technique. The silicon substrates (Si (111) surface) were modified with the azo groups, which were introduced by the treatment of Si (111) surface with 4,4′‐azobis (4‐cyanopentanoic acid). The poly(methyl methacrylate) (PMMA) were then prepared under RITP conditions from the Si (111) wafer. The synthesis of amphiphilic diblock copolymer was carried out on Si‐g‐PMMA substrate by sequential addition of monomer N‐isopropylacrylamide (NIPAM). The observed narrow molecular weight distributions (M_w/M_n), linear kinetic plots, and linear plots of molecular weight (M_n) versus monomer conversion indicate that the chain growth from the silicon substrates is a controlled process with a “living” characteristic. The ellipsometry and contact angle results indicated that the MMA had grafted from the surface of the silicon substrates successfully and the graft layer was well defined. The structure of the polymer and the ability to extend the chains were characterized and confirmed with the surface sensitive techniques such as X‐ray photoelectron spectroscopy and atomic force microscope. POLYM. ENG. SCI., 54:925–931, 2014. © 2013 Society of Plastics Engineers     

Synthesis of poly(methyl methacrylate‐g‐glycidyl azide) graft copolymers using N,N‐dithiocarbamate‐mediated iniferters

A glycidyl azide polymer with pendent N, N‐diethyl dithiocarbamate groups (GAP‐DDC) was prepared by the reaction of poly(epichlorohydrin) (PECH) with pendent N, N‐diethyl dithiocarbamate groups (PECH‐DDC) and sodium azide (NaN₃) in dimethylformamide (DMF). It was then used as a macro‐photoinitiator for the graft polymerization of methyl methacrylate (MMA). Photopolymerization was carried out in a photochemical reactor at a wavelength greater than 300 nm. Conversion was determined gravimetrically and first‐order time conversion plot for the polymerization system showed linear increase with the polymerization time indicating that polymerization proceed in controlled fashion. The molecular weight distribution (M_w/M_n) was in the range of 1.4–1.6 during polymerization. The formation of poly(methyl methacrylate‐g‐glycidyl azide) (PMMA‐g‐GAP) graft copolymer was characterized by gel permeation chromatography, FT‐IR spectroscopy, Thermogravimetric analysis, and differential scanning calorimetry. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nanostructured thermosetting epoxy systems modified with poly(isoprene‐b‐methyl metacrylate) diblock copolymer and polyisoprene‐grafted carbon nanotubes

Nanostructured thermosetting composites based on an epoxy matrix modified with poly(isoprene‐b‐methyl methacrylate) (PI‐b‐PMMA) block copolymer were prepared through PI block segregation. Morphological structures were examined by means of atomic microscopy force microscopy. As epoxy/pristine multi‐walled carbon nanotubes (MWCNT) systems were found to present big agglomerations, with a very poor dispersion of the nanofiller, epoxy/PI‐b‐PMMA/MWCNT systems were prepared by using polyisoprene‐grafted carbon nanotubes (PI‐g‐CNT) to enhance compatibility with the matrix and improve dispersion. It was found that the functionalization of MWCNT with grafted polyisoprene was not enough to totally disperse them into the epoxy matrix but an improvement of the dispersion of carbon nanotubes was achieved by nanostructuring epoxy matrix with PI‐b‐PMMA when compared with epoxy/MWCNT composites without nanostructuring. Nevertheless, some agglomerates were still present and the complete dispersion or confinement of nanotubes into desired domains was not achieved. Thermomechanical properties slightly increase with PI‐g‐CNT content for nanostructured samples, whereas for nonnanostructured epoxy/PI‐g‐CNT composites they appeared almost constant and even decreased for the highest nanofiller amount due to the presence of agglomerates. Compression properties slightly decreased with block copolymer content, while remained almost constant with nanofiller amount. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of grafting yield and molecular weight of m‐TMI‐grafted‐PP on the mechanical properties of wood fiber filled polypropylene composites

m‐Isopropenyl‐α, α‐dimethylbenzyl isocyanate (m‐TMI) was grafted on isotactic polypropylene (PP) using di‐cumyl peroxide as a reaction initiator under varying reaction conditions to yield m‐TMI‐g‐PP coupling agent with four sets of grafting yield and molecular weight. Grafting yield of the synthesized m‐TMI‐g‐PP were 1.80%, 2.01%, 9.05%, and 8.86% and molecular weight of the corresponding grafted polymer were 129,225; [Correction made here after initial online publication.] 187,240; 124,130; and 180,838, respectively. Rubberwood flour reinforced polypropylene composites were prepared using these coupling agents and tested for mechanical properties. m‐TMI‐g‐PP coupling agent with 9.09% grafting and 124230 M_w was found to give the highest tensile and flexural strengths. Flexural modulus of the coupled composites was higher than uncoupled composites. Interfacial region of the composites characterized by scanning electron microscope (SEM) suggest effective wetting of fiber by PP in the case of coupled composites. The effect of fiber loading on composites indicates continuous increment in tensile and flexural strengths in coupled composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44196.     

Highly reversible and repeatable PTCR characteristics of PMMA/Ag‐coated glass bead composites based on CTE mismatch phenomena

Positive temperature coefficient of resistivity (PTCR) behavior of poly(methyl methacrylate) PMMA/silver (Ag)‐coated glass bead composites has been investigated with reference to the conventional PMMA/carbon black (CB) composites. The PMMA/CB composites showed a sudden rise in resistivity (PTC trip) at 115°C, close to the glass transition temperature (T _g, 113°C) of the PMMA. However, the PTC trip temperature (92°C) of PMMA/Ag‐coated glass bead composites was appeared well below the T _g of PMMA. The room temperature resistivity and PTC trip temperature of the composites were also very much stable upon thermal cycling. Addition of 1 phr of nanoclay increased the PTC trip temperature of PMMA/CB composites to 120°C, close to the T _g (118°C) of PMMA/clay nanocomposites, while PMMA/clay/Ag‐coated glass bead nanocomposites showed the PTC trip at 98°C. We proposed that the mismatch in coefficient of thermal expansion (CTE) between PMMA and glass beads played a key role that led to a disruption in continuous network structure of Ag‐coated glass beads even at a temperature well below the T _g of PMMA. The decrease in dielectric permittivity of PMMA/Ag‐coated glass bead composites on increasing frequency indicated possible use of the PTC composites as dielectric material. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Poly(methyl methacrylate)‐grafted cellulose nanocrystals: One‐step synthesis,nanocomposite preparation,and characterization

Cellulose nanocrystals (CNCs) are ideal reinforcing agents for polymer nanocomposites because they are lightweight and nano‐sized with a large aspect ratio and high elastic modulus. To overcome the poor compatibility of hydrophilic CNCs in non‐polar composite matrices, we grafted poly(methyl methacrylate) (PMMA) from the surface of CNCs using an aqueous, one‐pot, free radical polymerization method with ceric ammonium nitrate as the initiator. The hybrid nanoparticles were characterized by CP/MAS NMR, X‐ray photoelectron spectroscopy, infrared spectroscopy, contact angle, thermogravimetric analysis, X‐ray diffraction, and atomic force microscopy. Spectroscopy demonstrates that 0.11 g/g (11 wt %) PMMA is grafted from the CNC surface, giving PMMA‐g‐CNCs, which are similar in size and crystallinity to unmodified CNCs but have an onset of thermal degradation 45 °C lower. Nanocomposites were prepared by compounding unmodified CNCs and PMMA‐g‐CNCs (0.0025–0.02 g/g (0.25–2 wt %) loading) with PMMA using melt mixing and wet ball milling. CNCs improved the performance of melt‐mixed nanocomposites at 0.02 g/g (2 wt %) loading compared to the PMMA control, while lower loadings of CNCs and all loadings of PMMA‐g‐CNCs did not. The difference in Young's modulus between unmodified CNC and polymer‐grafted CNC composites was generally insignificant. Overall, ball‐milled composites had inferior mechanical and rheological properties compared to melt‐mixed composites. Scanning electron microscopy showed aggregation in the samples with CNCs, but more pronounced aggregation with PMMA‐g‐CNCs. Despite improving interfacial compatibility between the nanoparticles and the matrix, the effect of PMMA‐g‐CNC aggregation and decreased thermal stability dominated the composite performance.     

Synthesis of 1,3‐benzodioxole end‐functionalized polymers via reversible addition–fragmentation chain transfer polymerization

Reversible addition–fragmentation chain transfer (RAFT) polymerization of styrene was carried out in the presence of a novel RAFT reagent, bearing 1,3‐benzodioxole group, benzo [1,3]dioxole‐5‐carbodithioic acid benzo [1,3]dioxol‐5‐ylmethyl ester (BDCB), to prepare end‐functionalized polystyrene. The polymerization results showed that RAFT polymerization of styrene could be well controlled. Number–average molecular weight (M_n(GPC)) increased linearly with monomer conversion, and molecular weight distributions were narrow (M_w/M_n < 1.4). The successful reaction of chain extension and analysis of ¹H NMR spectra confirmed the existence of the functional 1,3‐benzodioxole group at the chain‐end of polystyrene. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3535–3539, 2006     

Physical and mechanical properties of poly(methyl methacrylate)‐grafted natural rubber synthesized by methyl methacrylate photopolymerization initiated by N,N‐diethyldithiocarbamate functions previously created on natural rubber chains

Well‐defined poly(methyl methacrylate) (PMMA)‐grafted natural rubbers (NRs) were prepared to study the structure–property relationships. Syntheses were achieved by the photopolymerization of methyl methacrylate initiated by N,N‐diethyldithiocarbamate groups created beforehand in side positions on the NR chains. With this procedure, good control of the graft density and PMMA content could be obtained. Thermal, morphological, and mechanical properties of NR‐g‐PMMA copolymers were studied as a function of the NR/PMMA composition and graft density. NR‐g‐PMMAs containing 15–80% grafted PMMA showed characteristics of heterogeneous materials (characterized by two glass‐transition temperatures, those of PMMA and NR, in differential scanning calorimetry). Under these conditions, they developed the morphology of thermoplastic elastomers with PMMA nodules dispersed in the rubber matrix when the PMMA content was near 20%; conversely, they developed the morphology of softened thermoplastics with rubber nodules dispersed in PMMA when the PMMA content was near 80%. Graft copolymers containing about 20% PMMA remained essentially rubbery, but they were already different from pure NR. On the other hand, the thermal stability of NR wash improved after the introduction of PMMA grafts onto NR chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electrical conductivity and tensile properties of block‐copolymer‐wrapped single‐walled carbon nanotube/poly(methyl methacrylate) composites

Poly(methyl methacrylate) (PMMA) composites containing raw or purified single‐walled carbon nanotubes (SWCNTs) are prepared by in situ polymerization and solution processing. The SWCNTs are purified by centrifugation in a Pluronic surfactant, which consists of polyethyleneoxide and polypropyleneoxide blocks. Both the effects of SWCNT purity and non‐covalent functionalization with Pluronic are evaluated. Electrical conductivity of PMMA increases by 7 orders of magnitude upon the integration of raw or purified SWCNTs. The best electrical properties are measured for composites made of purified SWCNTs and prepared by in situ polymerization. Strains at fracture of the SWCNT/PMMA composites are nearly identical to those of the neat matrix. A certain decrease in the work to fracture is measured, particularly for composites containing purified SWCNTs (?31.6%). Fractography and Raman maps indicate that SWCNT dispersion in the PMMA matrix improves upon the direct addition of Pluronic, while dispersion becomes more difficult in the case of purified SWCNTs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41547.     

Enhancing crystallization rate and melt strength of PLLA with four‐arm PLLA grafted silica: The effect of molecular weight of the grafting PLLA chains

To improve the crystallization rate and melt strength of polylactide (PLLA), nano‐size amino silica grafted by four‐arm PLLA (4A‐PLLA) with different molecular weight was synthesized. ¹H nuclear magnetic resonance proved that 4A‐PLLA had been grafted onto the surface of SiO₂ successfully, and the grafting ratios and the degradation behaviors of the grafted SiO₂ nanoparticles (g‐SiO₂) were studied. When the grafted silica was introduced into PLLA matrix, the crystallization rate and melt strength of composites were found to be improved and the length of grafted chain played an important role. The extension rheology indicated that long grafted 4A‐PLLA on the surface of SiO₂ was more efficient in enhancing the elongational viscosity of PLLA, owing to the stronger interactions between the grafted chains and the matrix. The crystallization behavior of ungrafted silica filled composite was similar to that of neat PLA, while g‐SiO₂ played a role of nucleating agent. The crystallinities and the crystallization rates of the composites depended on the content of g‐SiO₂ and the grafted chain length of 4A‐PLLA, especially the latter. Longer grafted chain acted as nucleation site in the matrix and significantly improved the crystallization behaviors of PLLA. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45675.     

Effect of in situ polymerization conditions of methyl methacrylate on the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene) PMMA/AES Blends

In this study, the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene‐g‐styrene) (PMMA‐AES) blends were investigated with emphasis on the influence of the in situ polymerization conditions of methyl methacrylate. PMMA‐AES blends were obtained by in situ polymerization, varying the solvent (chloroform or toluene) and polymerization conditions: method A—no stirring and air atmosphere; method B—stirring and N₂ atmosphere. The blends were characterized by infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and dynamic mechanical analysis (DMA). The results showed that the PMMA‐AES blends are immiscible and present complex morphologies. This morphology shows an elastomeric dispersed phase in a glassy matrix, with inclusion of the matrix in the elastomer domains, suggesting core shell or salami morphology. The occlusion of the glassy phase within the elastomeric domains can be due to the formation of graft copolymer and/or phase inversion during polymerization. However, this morphology is affected by the polymerization conditions (stirring and air or N₂ atmosphere) and by the solvent used. The selective extraction of the blends' components and infrared spectroscopy showed that crosslinked and/or grafting reactions occur on the elastomer chains during MMA polymerization. The glass transition of the elastomer phase is influenced by morphology, crosslinking, and grafting degree and, therefore, T_g depends on the polymerization conditions. On the other hand, the behavior of T_g of the glassy phase with blend composition suggests miscibility or partial miscibility for the SAN phase of AES and PMMA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of PMMA composites activated with starch for immobilization of L‐asparaginase

Poly (methyl methacrylate) (PMMA)–starch composites were prepared by emulsion polymerization technique for L‐asparaginase (L‐ASNase) immobilization as highly activated support. The hydroxide groups on the prepared composites offer a very simple, mild and firm combination for enzyme immobilization. The pure PMMA and PMMA‐starch composites were characterized as structural, thermal and morphological. PMMA‐starch composites were found to have better thermal stability and more hydrophilic character than pure PMMA. L‐ASNase was immobilized onto PMMA‐starch composites contained the different ratio of starch (1, 3, 5, and 10 wt %). Immobilized L‐ASNase showed better performance as compared to the native enzyme in terms of thermal stability and pH. K_m value of immobilized enzyme decreased approximately eightfold compared with the native enzyme. In addition to, immobilized L‐ASNase was found to retain 60% of activity after 1‐month storage period at 4 °C. Therefore, PMMA‐starch composites can be provided more advantageous in terms of enzymatic affinity, thermal, pH and storage stability as L‐ASNase immobilization matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43421.     

Synthesis of NR‐g‐PMMA by “grafting from” method using ATRP process

Grafting poly(methyl methacrylate) or PMMA from natural rubber (NR) using ATRP process, NR has to be transformed into bromoalkyl‐functionalized NR (NRBr) acting as ATRP macroinitiator. The NRBr was prepared by two‐step chemical modification i.e., epoxidation and epoxide ring opening reaction using a nucleophile containing bromine atom such as 2‐bromopropionic acid ( A1 ) and 2‐bromo‐2‐methylpropionic acid ( A2 ). The fixation of A1 and A2 on 4‐methyl‐4‐octene, a model representing one repeat unit of NR, modified by epoxidation was prior studied and it was found that the resulting addition products from A2 using as ATRP initiator for MMA gave a better control of M _n,exp and low PDI of PMMA than that from A1 . Then, the NR was transformed into ATRP rubber macroinitiator via epoxidation, followed by epoxide ring addition with only A2 . ¹H NMR was employed to determine the amount of A2 addition units on NR, which is considered to be the same amount of grafting sites for ATRP of MMA. The grafting of PMMA was then successfully carried out from the NR backbone by ATRP process. The PMMA grafts of the NR‐g‐PMMA were indeed linked to the NR backbone via ester linkage of the A2 unit. The PMMA grafts could be cleaved from the NR backbone by acid hydrolysis, while PMMA grafting by other conventional radical reaction could not be done. Then, the average MW of PMMA grafts after separation using acetone extraction was evaluated. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of poly(aryl ether sulfone)‐graft‐polystyrene and poly(aryl ether sulfone)‐graft‐[polystyrene‐block‐poly(methyl methacrylate)] through atom transfer radical polymerization

A new graft copolymers poly(aryl ether sulfone)‐graft‐polystyrene (PSF‐g‐PS) and poly(aryl ether sulfone)‐graft‐[polystyrene‐block‐poly(methyl methacrylate)] (PSF‐g‐(PS‐b‐PMMA)) were successfully prepared via atom transfer radical polymerisation (ATRP) catalyzed by FeCl₂/isophthalic acid in N,N‐dimethyl formamide. The products were characterized by GPC, DSC, IR, TGA and NMR. The characterization data indicated that the graft copolymerization was accomplished via conventional ATRP mechanism. The effect of chloride content of the macroinitiator on the graft copolymerization was investigated. Only one glass transition temperature (T_g) was detected by DSC for the graft copolymer PSF‐g‐PS and two glass transition temperatures were observed in the DSC curve of PSF‐g‐(PS‐b‐PMMA). The presence of PSF in PSF‐b‐PS or PSF‐g‐(PS‐b‐PMMA) was found to improve thermal stabilities. © 2002 Society of Chemical Industry     

The synthesis of PHA‐g‐(PTHF‐b‐PMMA) multiblock/graft copolymers by combination of cationic and radical polymerization

A new and promising method for the diversification of microbial polyesters based on chemical modifications is introduced. Poly(3‐hydroxy alkanoate)‐g‐(poly(tetrahydrofuran)‐b‐poly(methyl methacrylate)) (PHA‐g‐(PTHF‐b‐PMMA)) multigraft copolymers were synthesized by the combination of cationic and free radical polymerization. PHA‐g‐PTHF graft copolymer was obtained by the cationic polymerization of THF initiated by the carbonium cations generated from the chlorinated PHAs, poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBHx) in the presence of AgSbF₆. Therefore, PHA‐g‐PTHF graft copolymers with hydroxyl ends were produced. In the presence of Ce⁺⁴ salt, these hydroxyl ends of the graft copolymer can initiate the redox polymerization of MMA to obtain PHA‐g‐(PTHF‐b‐PMMA) multigraft copolymer. Polymers obtained were purified by fractional precipitation. In this manner, their γ‐values (volume ratio of nonsolvent to the solvent) were also determined. Their molecular weights were determined by GPC technique. The structures were elucidated using ¹H‐NMR and FTIR spectroscopy. Thermal analyses of the products were carried out using differential scanning calorimeter (DSC) and thermogravimetric analysis (TGA). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

RAFT‐mediated emulsion polymerization of chloroprene and impact of chain‐end structure on chloroprene rubbers

The reversible addition‐fragmentation chain transfer (RAFT) polymerization of chloroprene (CP) in an emulsion system using a dithiocarbamate‐type RAFT agent was studied. The controlled RAFT‐mediated emulsion polymerization was achieved by the appropriate combination of a RAFT agent and nonionic surfactant (polyoxyethylene phenyl ether) using a water‐soluble initiator (VA‐044) at 35 °C. An almost linear first‐order kinetic plot was observed until relatively high conversion (>80%) with molecular weights between 22,300 and 33,100 and relatively narrow molecular weight distributions (M_w/M_n ≦ 1.5) were achieved. The amount of the emulsifier used and the pH of the system were found to affect the controlled character, polymerization rate, and induction period, which are related to the size of the emulsion particles. Large‐scale RAFT‐mediated emulsion polymerization was also employed to afford industrially applicable poly(CP) (M_w > 25 × 10⁴, resulting product > 2300 g). The vulcanized CP rubber obtained from the RAFT‐synthesized poly(CP) exhibited better physical properties, particularly tensile modulus and compression set, which may be due to the presence of the reactive end groups and the absence of low‐molecular‐weight products. We also evaluated the impact of the chain‐end structure on the mechanical and physical properties of these industrially important CP rubbers with carbon black. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46008.     

Synthesis of polypropylene graft copolymers from a hydroxyl‐groups‐containing polypropylene precursor via atom‐transfer radical polymerization

Isotactic polypropylene graft copolymers, isotactic[polypropylene‐graft‐poly(methyl methacrylate)] (i‐PP‐g‐PMMA) and isotactic[polypropylene‐graft‐polystyrene] (i‐PP‐g‐PS), were prepared by atom‐transfer radical polymerization (ATRP) using a 2‐bromopropionic ester macro‐initiator from functional polypropylene‐containing hydroxyl groups. This kind of functionalized propylene can be obtained by copolymerization of propylene and borane monomer using isospecific MgCl₂‐supported TiCl₄ as catalyst. Both the graft density and the molecular weights of i‐PP‐based graft copolymers were controlled by changing the hydroxyl group contents of functionalized polypropylene and the amount of monomer used in the grafting reaction. The effect of i‐PP‐g‐PS graft copolymer on PP‐PS blends and that of i‐PP‐g‐PMMA graft copolymer on PP‐PMMA blends were studied by scanning electron microscopy. Copyright © 2006 Society of Chemical Industry