共聚低热膨胀聚酰亚胺薄膜的制备与表征

以4,4′-(六氟异丙烯)二酞酸酐(6FDA)为含氟二酐,4,4′-二氨基-2,2′-双三氟甲基联苯(TFMB)为含氟二胺,通过引入分子结构相对对称的刚性单体1,2,4,5-均苯四甲酸二酐(PMDA)进行共聚合成了5种含氟比例不同的透明聚酰亚胺薄膜,并对其性能进行了表征。分析表明:引入刚性单体共聚后薄膜的热稳定性和耐热性有所提高;薄膜的介电常数随着PMDA含量的上升而增加;共聚薄膜在可见光领域的透光率低于均聚薄膜;拉伸实验显示在添加少量PMDA后,薄膜的拉伸强度和弹性模量有所增大,但当PMDA含量过高时其力学性能反而下降;随着PMDA含量的增加,薄膜的热膨胀系数明显降低。     

基于氧杂二甲桥八氢化萘二酐的新型聚酰亚胺共聚物的制备与研究

通过分子设计合成了一种含氧杂二甲桥八氢化萘大体积结构的新型二酐单体(BADA),并将其按不同的比例与联苯四酸二酐(BPDA)和4,4′-二氨基苯醚(ODA)进行共聚，制备了一系列聚酰亚胺粉末和薄膜材料。通过对新型二酐与新型聚酰亚胺的研究发现，该新型脂环族二酐具有良好的溶解性，且随着脂环族二酐含量的增加，聚酰亚胺表现出优异的溶解性和疏水性，有望应用于5G高频柔性印制电路中。     

共聚物链结构对共聚型含氟聚酰亚胺薄膜性能的影响

以4,4'-二氨基-2,2'-双三氟甲基联苯(TFMB)、4,4'-(六氟异丙烯)二酞酸酐(6FDA)和3,3',4,4'-联苯四甲酸二酐(BPDA)为反应单体,改变非含氟BPDA单体在二酐中的配比和加料方式制备出一系列共聚型含氟聚酰亚胺(PI)薄膜并表征和分析其性能,研究了共聚物链结构对其性能的影响。结果表明,BPDA单体的加料方式及其在二酐单体中的比例均影响薄膜的性能。共聚型含氟PI薄膜在室温下均溶于非质子极性溶剂,且在可见光范围内有较高的透光率。随着非含氟二酐单体BPDA含量的提高薄膜的光学性能略有降低而其热性能和力学拉伸性能提高。非含氟二酐单体占二酐单体的比例为68.97%的共聚型PI薄膜,在500 nm处的透过率达到96.01%;非含氟二酐单体占二酐单体比例为35.71%的共聚型PI薄膜失重10%的热分解温度为595.23℃,拉伸强度为100.98 MPa。同时,BPDA加料方式的改变对共聚型PI薄膜的光学性能、热学性能和力学拉伸性能均有不同程度的影响。     

共聚制备低热膨胀透明聚酰亚胺薄膜

为了在尽量不影响其透光性的前提下解决含氟聚酰亚胺薄膜热膨胀系数(CTE)过大的问题,以4,4′-(六氟异丙烯)二酞酸酐(6FDA)、4,4′-二氨基-2,2′-双三氟甲基联苯(TFMB)和3,3′,4,4′-联苯四羧酸二酐(BPDA)为原料,通过两步法合成了5种BPDA掺杂量分别为0、10%、20%、30%和40%的共聚PI薄膜,并采用红外光谱分析(IR)、热重分析(TGA)、热机械性能分析(TMA)等方法对其性能进行了表征.分析表明:共聚薄膜的热性能相比均聚薄膜有所提高;薄膜的介电常数与BPDA的含量成正比,而其在可见光领域的透光率与BPDA的含量成反比;在BPDA含量较低时,薄膜的拉伸强度和弹性模量随BPDA含量的增加而增大,但当BPDA摩尔分数超过30%时其力学性能开始降低;随着共聚单体含量的上升,薄膜的热膨胀系数大幅减小.     

基于2-苯基-4,4′-二氨基二苯醚的异构聚酰亚胺

以异构的联苯二酐(BPDA)、二苯醚二酐(ODPA)以及2-苯基-4,4′-二氨基二苯醚(p-ODA)为原料,通过一步法或两步法,合成了一系列异构聚酰亚胺,并表征了这类聚酰亚胺的溶解性、热性能和力学性能。结果表明:基于p-ODA的聚酰亚胺在有机溶剂中具有优异的溶解性;基于p-ODA的异构聚酰亚胺都是非晶结构,且聚酰亚胺的溶解性和玻璃化温度(Tg)呈现3,3′-位3,4′-位4,4′-位的趋势,聚合物Tg250℃。聚合物4,4′-ODPA/p-ODA具有较优的热稳定性,5%热失重温度(T5%)=551℃,聚合物3,4′-ODPA/p-ODA和4,4′-ODPA/p-ODA具有相似的机械性能。异构BPDA/p-ODA系列聚酰亚胺具有相似的热稳定性,T5%550℃,聚合物4,4′-BPDA/p-ODA的机械性能优异,薄膜拉伸强度为182.4MPa、模量为3.5GPa、断裂伸长率为44.2%。     

砜基取代高折射率高透明性聚酰亚胺的合成与性能

首先合成了同时含有砜基与硫醚键的二胺单体,4,4′-双(4-胺基苯硫基)二苯砜(BADPS).采用BADPS分别与4种二酐单体,3,3′,4,4′-联苯四羧酸二酐(BPDA)、3,3′,4,4′-二苯醚四羧酸二酐(ODPA)、4,4′-双(3,4-二羧基苯硫基)二苯硫醚二酐(3SDEA)以及1,2,3,4-环丁烷四羧酸二酐(CBDA)通过两步聚合工艺制备了一系列聚酰亚胺(PI).制备的PI薄膜具有优良的综合性能,包括良好的热稳定性、可见光波长范围内优良的透明性以及高折射率与低双折射.10mm厚的PI薄膜在450nm处的透光率超过80%.全芳香族PI(PI-1～PI-3)的折射率＞1.70,双折射＜0.02.     

含有氢键的聚酰亚胺薄膜的制备和性能表征

以对硝基苯甲酸为原料,通过酰氯化、酰化、还原反应成功合成了4,4’-二氨基苯酰替苯胺(DBN),DBN分别和3,3’,4,4’-联苯四酸二酐(BPDA)、均苯四甲酸二酐(PMDA)通过两步法缩聚制备出聚酰亚胺薄膜,用红外(FT-IR),差示扫描量热仪(DSC)和热重分析(TGA),拉伸测试表征其结构和性能,结果表明,成功合成了含有酰胺键的聚酰亚胺薄膜,并且酰胺键的N-H分别和酰亚胺环中的C-N和C=O形成了氢键。将其与4,4’-二氨基二苯醚(ODA)聚酰亚胺薄膜相比,对应二酐(BPDA和PMDA)分别和DBN制备的聚酰亚胺薄膜表现出了优异的热性能和耐溶剂性,尤其是拉伸强度有了显著的提高。     

一类含双叔丁基苯结构聚酰亚胺的合成与性能

通过分子设计制备一种含双叔丁基结构的刚性芳香二胺单体——4,4′-二氨基苯基-3″,5″-二叔丁基甲苯,将该二胺单体分别与3种不同的商品化芳香二酐(3,3′,4,4′-联苯四酸二酐(BPDA)、3,3′,4,4′-二苯醚酐(ODPA)、3,3′,4,4′-二苯酮四酸二酐(BTDA))采用一步高温缩聚制备了3种新型聚酰亚胺NPI(3a～3c)。该类聚酰亚胺具有优异的溶解成膜性能,在室温可溶解于N-甲基-2-吡咯烷酮、N,N-二甲基乙酰胺、间甲酚等高沸点溶剂中,在加热时还能溶解于CHCl_3,CH_2Cl_2,THF等低沸点溶剂,并可通过其聚合物溶液浇铸得到柔韧的薄膜;所制聚酰亚胺薄膜具有优良的热性能,玻璃化转变温度(T_g)范围为262～303℃,在N_2中质量损失10%的温度超过523℃;具有优异的光学性能,所制薄膜还具有较浅的颜色和良好的光学透过性,在450 nm波长光下的透光率为69%～76%,截止波长为341～353 nm。     

可溶性含羟基聚酰亚胺的制备及其性能研究

合成了含羟基的二胺单体4,4′-二氨基-4″-羟基三苯甲烷(DHTM),并将该单体分别同六氟异叉丙基二苯四羧酸二酐(6FDA),3,3′,4,4′-二苯醚四羧酸二酐(ODPA)和4,4′,-二(4,4′,-异丙叉二苯氧基)四羧酸二酐(BPADA)反应制备了3种结构的聚酰亚胺。溶解性实验表明,这3种聚合物在非质子极性溶剂中均显示出良好的溶解性。此外,还对聚酰亚胺薄膜进行了拉伸和动态机械热性能测试。     

含双苯并咪唑单元的聚酰亚胺的制备及性能

联苯四羧酸二酐(BPDA)与4,4′-二氨基二苯醚(ODA)及自制的2,2′-对苯基双-(5-氨基苯并咪唑)(PBABI)在二甲基乙酰胺中共聚,成膜后进行热酰亚胺化,得到了含双苯并咪唑共聚酰亚胺薄膜,对其结构、热稳定性、力学性能及光学性能进行了研究。结果表明,PBABI杂环单体的引入对聚酰亚胺的热分解温度稍有影响,但明显提高了聚合物的玻璃化转变温度。随着杂环含量的增加,材料的拉伸强度和模量均有所提高,当二胺单体的物质的量比为9∶1时,其力学性能提高明显。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.