Discharge characteristics and low‐voltage driving of high‐Xe‐content PDPs

Abstract— High‐Xe‐content PDPs attain improved luminous efficiency, but with sacrifices of higher sustain and address voltages and slower discharge build‐up. By examining PDPs with 3.5–100% Xe contents, it was revealed that space‐charge priming as well as wall‐charge accumulation are effective in obtaining low‐voltage and high‐speed operation. In addition, it was found that the effectiveness is emphasized for higher‐Xe‐pressure PDPs. In this respect, erase addressing is more favorable than write addressing, especially for high‐Xe‐pressure PDPs. The formative time lag of the discharge and diffusion/drift of the space charges are shorter for high Xe contents. In this respect, high‐Xe‐content PDPs have a potential for high‐speed addressing, if driven adequately. The use of space‐charge priming, however, is limited by the duration between the priming and scan pulses. Accumulation of wall charges is limited by ignition of a self‐erase discharge with which all the wall charges are dissipated. Although the highest efficiency and luminance are attained with a 100%‐Xe panel, the optimum Xe gas content, considering the sustain pulse voltage and drive voltage margin, would be 70% Xe + Ne.     

High‐speed low‐voltage driving of high‐Xe‐content PDPs with priming particles

Abstract— Power savings, image‐quality improvement, and cost reduction are the major issues facing PDP development. High‐Xe‐content PDPs have attained improved luminous efficiency, but with sacrifices in higher switching and sustain voltages and slower discharge build‐up. By examining PDPs having 3.5%–30% Xe content, it was found that utilization of the space‐charge priming effect as well as wall‐charge accumulation are effective in obtaining a low operating voltage and a high switching speed. The improvements are enhanced for higher Xe pressures. By using space‐charge priming, the statistical time lag of the discharge triggering for the 30% Xe content is reduced significantly and becomes approximately equal to that of 3.5% Xe content. Once triggered, the formative time lag of the discharge becomes shorter and the space charge experiences diffusion/drift; hence, accumulation of the wall charge is faster for discharges with higher Xe contents. These indicate that the use of an erase addressing scheme, rather than a write addressing scheme, is preferable when driving high Xe‐content PDPs, because the erase addressing scheme provides the addressing operation with an abundant amount of priming particles. Also, the drive voltages are lower for the erase addressing scheme. In order to reduce the address voltage, it is effective to accumulate wall charges prior to addressing. It was found that there are limiting values for the charge accumulation, above which self‐erase discharges ignite and the wall charge is dissipated. The self‐erase discharge occurs at relatively low wall voltages when the Xe percentages becomes higher. The sustain pulse voltage can be reduced while keeping the luminous efficiency high by increasing the sustain pulse frequency. As the frequency is increased, a residual amount of space charge created by the preceding sustain pulse increases. Due to the priming effect of these space charge, the build‐up of the discharge current becomes faster, resulting in a lower voltage.     

Very‐high‐brightness diodes for passive‐matrix display applications

Abstract— The development of a high‐brightness low‐voltage yellow‐light‐emitting polymer system suitable for use in low‐cost passive‐matrix displays will be reported. Average device efficiencies of 16 lm/W at 100 and 1000 cd/m² are achieved at 2.1 and 2.4 V, respectively. A luminance level of 100,000 cd/m² is achieved at 5.5 V.     

A portable driving system for high‐resolution active matrix electrowetting display based on FPGA

How to display pictures and even videos on electrowetting displays (EWDs) still needs improvement. Therefore, we seek to develop a robust, portable and scalable system for the realization of high‐resolution EWDs. In this paper, a driving system for an 8 inch active matrix electrowetting display (AM‐EWD) based on a Field‐Programmable‐Gate‐Array (FPGA) is proposed, where the key components are an active matrix backplane, an FPGA driving waveform and driver integrated circuits (ICs). We successfully demonstrate an AM‐EWD with 1024×768 resolution and 16‐level gray‐scale realized by unique dynamic and asymmetric sub‐frame of FPGA. The whole system is just powered by a 3.7V 1100mAH lithium battery. Such a system has not been reported before, also well‐suited for transferring to a higher performance portable EWD in the future.     

A 400‐dpi reflective storage ferroelectric liquid‐crystal display for highly readable,low‐power mobile display applications

Mobile products require longer battery lifetimes and increased information content from the display. A ferroelectric liquid‐crystal reflective storage mode was demonstrated. This display only needs updating when the image changes, resulting in ultra‐low power consumption. Passive‐matrix addressing allows for high‐resolution text to be displayed.     

Use of self‐erase discharges for high‐speed and low‐voltage addressing of PDPs

Abstract— A technique called “self‐erase‐discharge addressing” has been incorporated with a address‐while‐display driving scheme, contiguous subfield, and erase addressing to obtain high‐speed and low‐voltage addressing of PDPs. The technique uses a relatively high X‐sustain pulse voltage VXsus, which produces a weak self‐erase discharge at its trailing edge. An application of a data pulse Vdata synchronous to a weak self‐erase discharge results in full erase discharge and eliminates all the wall charges. The technique assures a wider operating‐voltage margin since it provides identical amounts of priming charges as well as wall charges to all the horizontal scan lines just prior to addressing. The priming charges are generated by the weak self‐erase discharges, resulting in low Vdata of 30 V and a high addressing speed of 0.66 μsec for a Ne + 10% Xe PDP. V_Xsus = 245 V, and the voltage margins of Vdata and VXsus were 35 and 16 V, respectively. For a 30% Xe PDP, Vdata and VXsus were 30 and 335 V, respectively, with an addressing speed of 1.0 μsec. In order to obtain high dark‐room contrast, it is essential to use ramp reset pulses, with which erase addressing cannot be achieved. By adopting the write addressing only to the first subfield and the self‐erase‐discharge addressing to the subsequent subfields, a peak and background luminance in green of 3100 and 0.22 cd/m², respectively, were obtained with a dark‐room contrast of 14,000:1. The number of subfields was 28, and the light emission duty was 83%. The number of ramp reset pulse drivers could be reduced to 12 by adopting the common reset pulse technique.     

Class G approach for low‐voltage,high‐efficiency PA design

Class G power amplifier (PA) design guidelines are presented and experimentally validated, showing the interesting features of the new approach. For the same operating conditions, the Class G amplifier exhibits superior performances if compared to a tuned load one in large signal gain, output power, and third‐order intermodulation (IM3), with a power‐added efficiency (PAE) improvement of 38.5%. © 2000 John Wiley & Sons, Inc. Int J RF and Microwave CAE 10: 366–378, 2000.     

Evaluation of jerkiness of moving three‐dimensional images produced by high‐density directional display

Abstract— The jerkiness of moving three‐dimensional (3‐D) images produced by a high‐density directional display was studied. Under static viewing conditions in which subjects' heads did not move, jerkiness was more noticeable when moving 3‐D images were displayed in front of the display screen and was less noticeable when moving 3‐D images were displayed behind the screen. We found that the perception of jerkiness depended on the visual angular velocities of moving 3‐D images. Under dynamic viewing conditions in which subjects' heads were forced to move, when moving 3‐D images were displayed in front of the screen, jerkiness was less noticeable when the subjects' heads and 3‐D images moved in opposite directions and was more noticeable when they moved in the same direction. When moving 3‐D images were displayed behind the screen, jerkiness was less noticeable when subjects' heads and 3‐D images moved in the same direction and was more noticeable when they moved in opposite directions.     

A Flexible electronic‐paper display with an ultra‐thin and flexible LSI driver using quick‐response liquid‐powder technology

Abstract— A thin and flexible LSI driver with a thickness of less than 35 μm for a passive‐matrix‐driven Quick‐Response Liquid‐Powder Display (QR‐LPD?) was successfully mounted onto the flexible printed circuit (FPC) and the back substrates of a flexible QR‐LPD?. Amounted LSI driver on a plastic substrate shows no significant degradation in the driving performances and maintains physical flexibility without any connection failures. This technology can realize a fully flexible electronic paper in combination with a plastic‐substrate QR‐LPD? fabricated by a roll‐to‐roll process.     

High‐frequency drive of high‐Xe‐content PDPs for high efficiency and low‐voltage performance

Abstract— It has been well known that the luminous efficiency of PDPs can be improved by increasing the Xe content in the panel. For instance, the efficiency is improved by a factor 1.7 when the Xe content is increased from 3.5% to 30%. The sustain pulse voltage, however, increases from 180 to 230 V by a factor 1.3. It was found that the increase in the sustain pulse voltage can be suppressed by increasing the sustain pulse frequency. The high‐frequency operation further increases the luminous efficiency. If the Xe content is increased from 3.5% to 30% and the drive pulse frequency is increased from 147 to 313 kHz, the luminous efficiency becomes 2.7 times higher and the luminance 4.5 times higher. Furthermore, the increase in the sustain pulse voltage is suppressed 1.1 times, from 180 to 200 V. A mechanism of attaining high efficiency and low‐voltage performance can be considered as follows. A train of pulses is applied during a sustain period. As the sustain pulse frequency is increased, the pulse repetition rate becomes faster and a percentage of the space charge created by the previous pulse remains until the following pulse is applied. Due to the priming effect of these space charge, the discharge current build‐up becomes faster, the width of the discharge current becomes narrower, ion‐heating loss is reduced, and the effective electron temperature is optimized so that Xe atoms are excited more efficiently. The intensity of Xe 147‐nm radiation, dominant in low‐pressure Xe dis‐charges, saturates with respect to electron density due to plasma saturation. This determines the high end of the sustain pulse frequency.     

Practical CNT‐FED structure for high‐luminance character displays

Abstract— A high‐luminance CNT‐FED character display using a simple line rib structure was constructed. The display panel had 48 × 480 dots and the subpixel pitch was 1 mm. The greatest benefit of a display using CNT technology is high luminance performance with low‐power consumption. The luminance of the green‐color dot wasca. 10,000 cd/m² under 1/1 6 duty‐cycle driving at a 6‐kV anode voltage. The high luminance of the display panel can provide good visibility when installed even in outdoor locations, and the power consumption was ca. 4 W at the character displaying module. This, a CNT‐FED for character displays also has potential multifunctionality, which could be battery driven. It should be useful for public displays even under emergency no‐power conditions. In this work, a practical structure and process technologies for making ribs with reasonable cost were developed. The newly introduced 2‐mm‐tall line ribs as spacers were formed by using innovative production processes; i.e., the rib paste was pushed out of a multi‐slit nozzle, and the rib shape was formed by UV‐light irradiation. The developed panel structure and manufacturing processes also had the advantages of size flexibility and high production yield.     

An affordable surround‐screen virtual reality display

Abstract— Building a projection‐based virtual reality display is a time‐, cost‐, and resource‐intensive enterprise, and many details contribute to the final display quality. This is especially true for surround‐ screen displays where most of them are one‐of‐a‐kind systems or custom‐made installations with specialized projectors, framing, and projection screens. In general, the costs of acquiring these types of systems have been in the hundreds and even millions of dollars, specifically for those supporting synchronized stereoscopic projection across multiple screens. Furthermore, the maintenance of such systems adds an additional recurrent cost, which makes them hard to afford for general introduction in a wider range of industry, academic, and research communities. A low‐cost easy‐to‐maintain surround‐screen design based on off‐the‐shelf affordable components for the projection screens, framing, and display systems is presented. The resulting system quality is comparableto significantly more expensive commercially available solutions. Additionally, users with average knowledge can implement this design, and it has the added advantage that single components can be individually upgraded based on necessity as well as available funds.     

A reflective‐display QR‐LPD®

Abstract— A novel reflective display [Quick‐Response Liquid Powder Display (QR‐LPD®)], has been developed. This paper‐like display has the advantages of outstanding image stability, easy viewing, low‐power consumption, and a high‐response time. QR‐LPD® will be promoted, initially, for use as electronic price‐tag displays for merchandise. In addition, QR‐LPD® is suitable for flexible display applications because it does not require TFT arrays or a high‐temperature process while maintaining an excellent paper‐like image as well as glass‐type display compatibility.     

Advances towards high‐resolution pack‐and‐go displays: A survey

Abstract— Tiled displays provide high resolution and large scale simultaneously. Projectors can project on any available surface. Thus, it is possible to create a large high‐resolution display by simply tiling multiple projectors on any available regular surface. The tremendous advancement in projection technology has made projectors portable and affordable. One can envision displays made of multiple such projectors that can be packed in one's car trunk, carried from one location to another, deployed at each location easily to create a seamless high‐resolution display, and, finally, dismantled in minutes to be taken to the next location — essentially a pack‐and‐go display. Several challenges must be overcome in order to realize such pack‐and‐go displays. These include allowing for imperfect uncalibrated devices, uneven non‐diffused display surfaces, and a layman user via complete automation in deployment that requires no user invention. We described the advances we have made in addressing these challenges for the most common case of planar display surfaces. First, we present a technique to allow imperfect projectors. Next, we present a technique to allow a photometrically uncalibrated camera. Finally, we present a novel distributed architecture that renders critical display capabilities such as self‐calibration, scalability, and reconfigurability without any user intervention. These advances are important milestones towards the development of easy‐to‐use multi‐projector displays that can be deployed anywhere and by anyone.     

Portable multi‐gray scale video playing scheme for high‐performance electrowetting displays

Electrowetting display technology is realized by tuning the surface energy of a hydrophobic surface by applying a voltage based on electrowetting mechanism. Electrowetting displays have favorable optical properties combined with reflective paper‐like performance. It has been successfully demonstrated in reflective mode with high switching speed. In this paper, we propose a portable driving scheme that can display 4‐bit gray scale dynamic video using an active matrix electrowetting display. The proposed driving scheme includes an electronic system and a dynamic driving waveform design. High‐performance multi‐gray video playing and quick response were obtained for a Quarter Video Graphics Array electrowetting display cell fabricated by our team.     

A novel low‐power‐consumption all‐digital system‐on‐glass display with serial interface

Abstract— A new conceptual ultra‐compact LCD panel, which features a simple interface and lower‐power consumption by using low‐temperature polysilicon thin‐film transistor (LTPS‐TFT) technology has been developed. This panel is capable of switching operation modes based on an input command, and all the data are directly communicated with the circuit inside the panel through a Serial Peripheral Interface (SPI) protocol. The integration of the serial‐data‐receiver function on glass substrate has enabled the achievement of a significant reduction in the number of interface pins. Moreover, a low power consumption of 15 μW for a 2.26‐in. reflective LCD panel in combination with the technique of integrating a memory circuit in each pixel has been achieved.     

A high‐contrast front‐projection display system optimizing the projected light‐angle range

Abstract— The problem with front‐projection displays is that the screen contrast ratio decreases under bright‐ambient conditions. To overcome this problem, the design of a special screen, composed of the diffuser whose diffusing property shows top‐hat characteristics and a sawtooth reflector, is proposed. The screen diffuses the incident image light arriving at a projection‐angle range that is a lower‐angle range than the viewing‐angle range, and reflects the ambient light out of the viewing‐angle range. In this paper, the projection‐angle range and the viewing‐angle range was optimized to improve the contrast ratio of a front‐projection display. As a result, a special screen with the above‐mentioned diffusing property was realized, and a high‐quality front‐projection display with a high contrast ratio, even in a bright room, was achieved.     

A high‐efficiency holographic waveguide display system with a prism in‐coupler

Holographic waveguide display system with high efficiency is presented by embedding an in‐coupling prism and an out‐coupling reflective volume holographic element, which enables a small‐type configuration. The improved coupling scheme can achieve 25% efficiency and the chromatic is corrected properly.     

A large high‐resolution electroluminescent display

A new high‐resolution electroluminescent display with a luminance of 100 cd/m² (30 fL) and 6‐bit gray scale to support real‐time video up to a bandwidth of 45 MHz has been developed under the Defense Advanced Research Projects Agency's Technology Reinvestment Project. Production units are now installed in the M1A2 Abrams Main Battle Tank upgrade program and are used to display the tank commander's new infrared “second‐generation FLIR” imagery.     

Time‐multiplexed color image generation by viewing‐zone scanning holographic display employing MEMS‐SLM

The viewing‐zone scanning holographic display, which can enlarge both screen size and viewing zone, is modified to enable color image generation by using the time‐multiplexing technique; R, G, and B lasers sequentially illuminate a single microelectromechanical systems spatial light modulator with a high frame rate. The viewing‐zone scanning system enlarges screen size by using a magnifying imaging system and generates a large number of reduced viewing zones that are aligned in the horizontal direction by a horizontal scanner to enlarge the viewing zone. The interval of the reduced viewing zones is set to be one‐third of the width of the reduced viewing zones or less so that three sets of reduced viewing zones are generated corresponding to the three colors. Color image generation was demonstrated for a screen size of 2.0 in. and a viewing zone angle of 40.0°.