共查询到20条相似文献,搜索用时 31 毫秒
1.
The textures of two different conical shaped liners, fabricated by the same forging processes from arc-cast and powder-sintered ingots, were investigated by using neutron-diffraction measurements and three-dimensional orientation-distribution-function (ODF) analysis. The major textures of both liners could be described by the (1 1 1) uv w and (1 0 0) u v w type. The two liners had essentially identical texture at the 8 cm position (measured from the base of the cone) with strong sheet-type texture components, i.e. (1 1 1) ¯1 0 1, (1 1 1) ¯1 1 0 and (1 0 0) 0 1 1. However, the dominant textures at the 3 cm positions were 1 1 1 and 1 0 0 fibre textures with the fibre axes oriented parallel to the normal direction in both liners. A strong cube texture was observed at the 3 cm position of the arc-cast liner but it was not observed for the powder-sintered liner. The arc-cast liner had a generally higher degree of texture than the powder-sintered liner. 相似文献
2.
Recrystallization textures in rolled copper specimens have been investigated so as to elucidate the mechanisms of cube texture formation. The specimens are single crystals with the orientations corresponding to the main components of the rolled textures, such as {112}111,{110}112, etc. and bicrystals consisting of such oriented crystals. The cube texture was not observed in any single crystal specimens, but observed in only two bicrystal specimens with {112}/111{100}001 and {110}112/{100}001 orientations. The formation of cube texture seems to require the existence of a cube oriented region in the deformed state, and the favourable oriented matrix to allow the growth of such nuclei. 相似文献
3.
An imperfectly B2 ordered Fe3Al aggregate was cast, thermomechanically hot rolled and finally annealed at 870 K. Subsequently, the specimen was rolled at 800–830 K to a strain of 80%. The microstructure and the crystallographic texture of the rolled polycrystalline sample was investigated within the range =20–80%. The microstructure consisted of flat, elongated grains. In numerous grains straight slip lines were detected. Even after =80% recrystallization was not observed. The rolling texture of Fe3Al considerably deviates from that of non-ordered body centered cubic (b.c.c.) alloys and pure b.c.c. metals. The {111}uvw texture fibre (7-fibre) was very pronounced, while the {hkl}110 fibre (-fibre) was very weak. The {112}110 orientation which represents the strongest texture component in non-ordered b.c.c. alloys did not occur at all. The textures are discussed in terms of the {110}111, {112}111, {112}111 and {123}111 slip systems. The contribution of crystallographic slip of the various types of potential slip systems was simulated by means of the Taylor theory. 相似文献
4.
Tensile tests at 20° C have been carried out on seventy-three sapphire whiskers and on seventeen silicon nitride whiskers. The sapphire whiskers were of 0001, 1¯120, 10¯10, and 10¯11 orientations, while the silicon nitride whiskers were 0001, 11¯20, and 10¯13. Tensile strengths were in the range 45 to 1500 kg/mm2, and deformation was found to be purely elastic. The tensile strength data have been analysed and fitted to empirical equations describing the effect of size on strength for different orientations. These empirical equations have been used to deduce possible fracture nucleation mechanisms. It is concluded that, in the case of 0001 sapphire whiskers, fracture nucleation may be due to dislocation pile-ups or interactions, while in the other cases a Griffith flaw mechanism is probably applicable. 相似文献
5.
Y. G. Wang H. Q. Ye K. H. Kuo X. J. Feng G. L. Liao S. Z. Long 《Journal of Materials Science》1991,26(21):5725-5732
Samples having the nominal composition of Ca3SrAl6SO16 were sintered at 1380 °C and analysed by electron diffraction. The frequent appearances of forbidden and satellite reflections in this compound imply the presence of a number of basal and nonbasal superlattices so that the microstructure of this cement clinker was characterized by various superstructures including one-, two- and even three-dimensional superstructures along the 0 0 1, 1 1 0, 1 1 2, 1 1 4 or 2 2 1, 0 1 3 and 1 2 3 directions with repeat periods of two or three times of that of basic one, respectively, and intergrowth of these. Various domain structures with 90°, 120° and 48.2°, etc., orientation relationships were also detected in these superstructures and the total number of these orientation variants related to the symmetry elements lost in the process of phase transformation, can be predicted according to the conclusions of Van Tendeloo and Amerlinckx, or they are equal to the number of those unique planes in the matrix. 相似文献
6.
G. Torres-Villaseñor R. Barrio-Paredes S. Victor Radcliffe 《Journal of Materials Science》1978,13(10):2164-2170
The stress-strain behaviour under compresion at constant strain rate of single crystals (051 and 122) compression axis) and polycrystalline samples of cuprous oxide have been examined at room temperature and hydrostatic pressure up to 12 kb and at atmospheric pressure and high temperature up to 600° C. At high environmental pressure, plastic flow occurs at 6 kb. At high temperatures and one atmosphere, extensive plastic deformation was observed after 500° C. The resultant slip planes were of the {110} and {100} types. Transmission electron microscopy of thin foils prepared from deformed specimens shows that the Burgers' vectors of the glide dislocations are of the 111, 110 and 100 types. 相似文献
7.
Yu. V. Shaldin 《Inorganic Materials》2001,37(6):560-563
The magnetic susceptibility of high-resistivity CdTeIn and CdTeCl crystals was measured between 4.2 and 300 K. The susceptibility was found to vary anomalously with temperature. Below 50 K, all the samples were paramagnetic. The observed anomalies are interpreted in terms of donor–acceptor pairs formed by native defects and dopant or uncontrolled impurity atoms. The effect of doping on the 300-K is related to the Van Vleck paramagnetic contribution resulting from the local electric fields of Xi–V
Cdand Ini–V
Cddefect complexes. In CdTeCl, this contribution is insignificant. 相似文献
8.
The agglomeration process that occurs during annealing of thin Fe films (<200 nm) on Si substrates has been studied. Agglomeration occurred on uncapped films prior to silicide formation. Capping layers of SiO2, or more appropriately Si-SiO2, have been used to minimize agglomeration effects. Continuous thin films of -FeSi2 have been grown on 11 1 and 100 oriented substrates. Preferred growth of (202) and (220) suicide planes on 111 Si has been obtained, while preferential growth was not observed on 100 Si. 相似文献
9.
Photosensitive Centers in CdTe〈Ge〉, CdTe〈Sn〉, and CdTe〈Pb〉 总被引:1,自引:0,他引:1
P. N. Gorlei O. A. Parfenyuk M. I. Ilashchuk K. S. Ul'yanitskii V. R. Burachek S. N. Chupyra 《Inorganic Materials》2003,39(11):1127-1131
The spectral and temperature dependences of photoconductivity in CdTePb crystals under band-gap and combined excitation were studied at photon energies in the range 0.53–1.7 eV and temperatures from 80 to 300 K. The high photosensitivity of the crystals and the observed IR and temperature quenching of photoconductivity indicate that, just as in CdTeGe and CdTeSn, the recombination processes in CdTePb are dominated by deep centers with drastically different capture cross sections for electrons and holes. Some parameters of the centers are determined. The results suggest that the likely defect species responsible for the high photosensitivity of CdTePb is an acceptor complex consisting of a Cd vacancy and a metal (Ge, Sn, Pb) ion on the Cd site: (V
2–
CdM+)–/0. 相似文献
10.
The birefringence topography of a Bi12GeO20 single crystal which has a strong natural optical activity is presented. The natural optical activity of the crystal may be completely compensated by reflection polarised light microscopy so that the birefringence images of dislocations and subboundaries are observed. The Burgers' vectors of dislocations were found to be of the types 1/2 1 1 1, 1 0 0 and 1 1 0 and dislocations which form subboundaries are also of these types. 相似文献
11.
Icosahedral T2 phases can form either by solid-state precipitation or during solidification in Al-Li-Cu-Mg alloys. The T2 phase forming during solidification can transform to an R phase at high annealing temperatures. The T2 phase forming by solid-state precipitation coexists with the Y phase, which has a face-centred cubic (f.c.c.) structure with lattice parameter a2.0 nm and can form microtwins with the twin plane of (111). The orientation relationships between the C phase and the T2 phase are: i¯5Y0 1 1, Y1 1 3; i¯3Y1 1 1, Y1 2 3, Y1 1 5; Y2 3 5; i2Y0 1 1, Y1 1 1, Y1 1 2, Y1 1 3, Y1 1 5. 相似文献
12.
On the basis of computer-calculated yield functions, the work hardening of 100 textured Cu-0.64 at % Co-0.48 at % Si and 111 textured polycrystalline copper wires were studied by simultaneous torsion and extension and by pure extension. Representing the work hardening by resolved shear stress-resolved shear strain curves, the rate of hardening is significantly lower for torsion than for pure extension. This behaviour is explained by the operation of different slip systems activated in the two modes of deformation. In the 100 textured Cu-Co-Si wires, heterogeneous plastic deformation was observed beyond about 80% shear strain. 相似文献
13.
Tensile properties and plastic deformation modes of zirconium-niobium alloys were investigated at 290 and 77 K in the wide composition range from metastable to stable phase. Three types of plastic deformation modes, {332}113 twinning, {112}111 twinning and slip, were observed depending on alloy composition and temperature. {332}113 twinning, which occurs in metastable zirconium alloys, is related to the stability of phase to decomposition and leads to low yield stress and large elongation. On the other hand, {112}111 twinning, which appears in stable zirconium alloys, results from high critical stress for slip due to solution hardening and high Peierls stress and does not affect tensile properties significantly. The results obtained for zirconium-alloys are similar to those for titanium alloys, strongly suggesting that {332}113 twinning is an important plastic deformation mode which is common to phase alloys containing athermal phase. 相似文献
14.
A crystallographic analysis of the atom positions in the unit cell of the R-phase of the TiNi shape memory alloy has been performed. In addition to a homogeneous shape change the atoms are found to shuffle in the [111]B2 and –211B2 directions during the B2 to R-phase transformation. The origin of these shuffles is found to be a complex interaction between 1101–10 transverse acoustic and 111 longitudinal acoustic soft phonon modes. 相似文献
15.
Deformation of single crystals of gallium arsenide is reported in bend and tension up to 1000° C whilst maintaining stoichiometry in an arsenic atmosphere. Surface defects and impurity segregation are shown to be dislocation sources. The dislocation density is low enough, however, to show large yield drops which are analysed in detail. Strains of 39% are possible. The activation energy for dislocation movement is increased by heat-treatment owing to an increase in point defect population.Electron microscopy shows that the predominant slip systems are {111} 110 and the majority of dislocations have b=a/2 110, the axes lying along 110 and 112 directions. Sub-cell formation occurs with sub-boundaries lying along 110 directions. 相似文献
16.
Polycrystalline Co-49.3at% Al which had been extruded at 1505 K was examined using transmission electron microscopy. Diffraction contrast analysis showed that b = 100 as well as b = 111 dislocations contribute to elevated temperature deformation in CoAl. Therefore, it was concluded that sufficient slip systems exist in CoAl to allow for general plasticity in the absence of diffusional mechanisms. Since no examples of b = 110 dislocations were found, the importance of 110{1¯10} slip in CoAl at 1505 K is unclear. Dislocations of the type b = 001 were observed on both {110} and {100} planes while b = 111 dislocations were observed on {1¯10} planes. 相似文献
17.
The growth of twinned crystals of aluminium on solidification is discussed with reference to the structure of the growing tip. It is shown that one must differentiate between two types of 112 growth directions in the twin boundary. Normally, all the tips grow in the same type of 112 growth direction and this particular type may give the tip a favourable shape, possibly by producing a sharp edge. If a tip is growing in a less favourable 112 direction, the favourable type can be established by the twins changing sides. This is observed to occur regularly in the continuous casting method according to Hunter. The re-entrant edge mechanism is not supported by the present results. 相似文献
18.
R. Tidecks 《Journal of Low Temperature Physics》1985,58(5-6):439-449
Based on the assumption that a phase-slip center in a clean quasi-one-dimensional superconductor excites a collective oscillation, the time-averaged value of the electrochemical potential of quasiparticles is calculated. At larger distances from the phase-slip center, swings below (or above) the electrochemical potential
p
of the Cooper pairs. This makes it possible to understand the unexpected results of previous measurements. 相似文献
19.
The ratios of the plastic shear strain and tensile strain to the resolved shear strain are determined on the basis of earlier results obtained by computer for 1 0 0 and 1 1 1 textures and nontextured polycrystals in the case of simultaneous shear and extension. It is shown that the plastic deformation increment vector determined by the application of the plastic work equation fulfils the normality condition prescribed by the generalized flow law. 相似文献
20.
The 100, 111 and 110 textures of copper electrodeposits obtained from copper sulfate baths changed to the 100, 100 and
textures, respectively, after recrystallization. The textures of chromium electrodeposits obtained from the standard Sargent bath remained unchanged after recrystallization. The results are in agreement with the prediction of the strain energy release maximization model, in which the recrystallized grains orient themselves so that their minimum elastic modulus direction can be parallel to the absolute maximum internal stress direction due to dislocations in the non-recrystallized grains. 相似文献