Characterization of highly doped n- and p-type 6H-SiCpiezoresistors

Highly doped (~2×10¹⁹ cm^-3) n- and p-type 6H-SiC strain sensing mesa resistors configured in Wheatstone bridge integrated beam transducers were investigated to characterize the piezoresistive and electrical properties. Longitudinal and transverse gauge factors, temperature dependence of resistance, gauge factor (GF), and bridge output voltage were evaluated. For the n-type net doping level of 2×10¹⁹ cm^-3 the bridge gauge factor was found to be 15 at room temperature and 8 at 250°C. For this doping level, a TCR of -0.24%/°C and -0.74%/°C at 100°C was obtained for the n- and p-type, respectively. At 250°C, the TCR was -0.14%/°C and -0.34%/°C, respectively. In both types, for the given doping level, impurity scattering is implied to be the dominant scattering mechanism. The results from this investigation further strengthen the viability of 6H-SiC as a piezoresistive pressure sensor for high-temperature applications     

Reliability of AlInAs/GaInAs heterojunction bipolar transistors

The reliability of high-performance AlInAs/GaInAs heterojunction bipolar transistors (HBTs) grown by molecular beam epitaxy (MBE) is discussed. Devices with a base Be doping level of 5×10¹⁹ cm^-3 and a base thickness of approximately 50 nm displayed no sign of Be diffusion under applied bias. Excellent stability in DC current gain, device turn-on voltage, and base-emitter junction characteristics was observed. Accelerated life-test experiments were performed under an applied constant collector current density of 7×10⁴ A/cm² at ambient temperatures of 193, 208, and 328°C. Junction temperature and device thermal resistance were determined experimentally. Degradation of the base-collector junction was used as failure criterion to project a mean time to failure in excess of 10⁷ h at 125°C junction temperature with an associated activation energy of 1.92 eV     

Improved inversion channel mobility for 4H-SiC MOSFETs followinghigh temperature anneals in nitric oxide

Results presented in this letter demonstrate that the effective channel mobility of lateral, inversion-mode 4H-SiC MOSFETs is increased significantly after passivation of SiC/SiO₂ interface states near the conduction band edge by high temperature anneals in nitric oxide. Hi-lo capacitance-voltage (C-V) and ac conductance measurements indicate that, at 0.1 eV below the conduction band edge, the interface trap density decreases from approximately 2×10¹³ to 2×10¹² eV^-1 cm^-2 following anneals in nitric oxide at 1175°C for 2 h. The effective channel mobility for MOSFETs fabricated with either wet or dry oxides increases by an order of magnitude to approximately 30-35 cm²/V-s following the passivation anneals     

Thin-film transistors in polycrystalline silicon by blanket andlocal source/drain hydrogen plasma-seeded crystallization

Thin film n-channel transistors have been fabricated in polycrystalline silicon films crystallized using hydrogen plasma seeding, by using several processing techniques with 600 to 625°C or 1000°C as the maximum process temperature. The TFTs from hydrogen plasma-treated films with a maximum process temperature of 600°C, have a linear field-effect mobility of ~35 cm²/Vs and an ON/OFF current ratio of ~10⁶, and TFTs with a maximum process temperature of 1000°C, have a linear field-effect mobility of ~100 cm²/Vs and an ON/OFF current ratio of ~10⁷. A hydrogen plasma has also then been applied selectively a in the source and drain regions to seed large crystal grains in the channel. Transistors made with this method with maximum temperature of 600°C showed a nearly twofold improvement in mobility (72 versus 37 cm² /Vs) over the unseeded devices at short channel lengths. The dominant factor in determining the field-effect mobility in all cases was the grain size of the polycrystalline silicon, and not the gate oxide growth/deposition conditions. Significant increases in mobility are observed when the grain size is in order of the channel length. However the gate oxide plays an important role in determining the subthreshold slope and the leakage current     

Avalanche phenomena in 4H-SiC p-n diodes fabricated by aluminum orboron implantation

Characteristics of p-n junction fabricated by aluminum-ion (Al⁺) or boron-ion (B⁺) implantation and high-dose Al⁺-implantation into 4H-SiC (0001) have been investigated. By the combination of high-dose (4×10¹⁵ cm^-2) Al⁺ implantation at 500°C and subsequent annealing at 1700°C, a minimum sheet resistance of 3.6 kΩ/□ (p-type) has been obtained. Three types of diodes with planar structure were fabricated by employing Al+ or B+ implantation. B ⁺-implanted diodes have shown higher breakdown voltages than Al⁺-implanted diodes. A SiC p-n diode fabricated by deep B+ implantation has exhibited a high breakdown voltage of 2900 V with a low on-resistance of 8.0 mΩcm² at room temperature. The diodes fabricated in this study showed positive temperature coefficients of breakdown voltage, meaning avalanche breakdown. The avalanche breakdown is discussed with observation of luminescence     

3100 V, asymmetrical, gate turn-off (GTO) thyristors in 4H-SiC

A 2-mm×2-mm, 4H-SiC, asymmetrical npnp gate turn-off (GTO) thyristor with a blocking voltage of 3100 V and a forward current of 12 A is reported. This is the highest reported power handling capability of 37 kW for a single device in SiC. The 5-epilayer structure utilized a blocking layer that was 50 μm thick, p-type, doped at about 7-9×10¹⁴ cm^-3. The devices were terminated with a single zone junction termination extension (JTE) region formed by ion-implantation of nitrogen at 650°C. The device was able to reliably turn-on and turn-off 20 A (500 A/cm²) of anode current with a turn-on gain (I_K/I_{G, on}) of 20 and a turn-off gain (I_K/I_{G, off}) of 3.3     

A proposed single grain-boundary thin-film transistor

A new Si thin-film transistor (TFT) has been proposed where only one grain-boundary exists at the center of channel, and the source and drain are within single grains with good crystallinity. The device fabricated by an excimer-laser crystallization method at the maximum temperature of 500°C, had the on-off current ratio ≅10⁶ , the field-effect mobility ≅330 cm²/Vs and the subthreshold swing ≅1.1 V/dec, respectively, For the device processed at 800°C, they are >10⁶, >450 cm² /Vs and ≅0.51 V/dec, respectively     

Low loss channel waveguides fabricated in fused silica by germaniumion implantation

The authors report the first low loss channel waveguides (0.10 0.15 dB/cm) formed in fused silica by the implantation of MeV Ge ions. The loss coefficient α was measured as a function of ion dose (8×10¹³-8×10¹⁶ ion/cm²) and annealing temperature (250 to 600°C) at 1300 nm. The as-implanted waveguides exhibited a minimum value of α=0.9 dB/cm at an intermediate range of dose with a reduction to 0.10-0.15 dB/cm after annealing at 500°C     

Electrical properties of Ga-implanted Si p+-n shallowjunctions fabricated by low-temperature rapid thermal annealing

p⁺-n shallow-junction diodes were fabricated using on-axis Ga⁶⁹ implantation into crystalline and preamorphized Si, at energies of 25-75 keV for a dose of 1×10¹⁵/cm ², which is in excess of the dosage (2×10¹⁴/cm²) required to render the implanted layer amorphous. Rapid thermal annealing at 550-600°C for 30 s resulted in the solid-phase epitaxial (SPE) regrowth of the implanted region accompanied by high Ga activation and shallow junction (60-130 nm) formation. Good diode electrical characteristics for the Ga implantation into crystalline Si were obtained; leakage current density of 1-1.5 nA/cm² and ideality factor of 1.01-1.03. Ga implantation into preamorphized Si resulted in a two to three times decrease in sheet resistance, but a leakage current density orders of magnitude higher     

Electrical characteristics of 4.5 kV implanted anode 4H-SiC p-i-njunction rectifiers

4500 V 4H-SiC p-i-n junction rectifiers with low on-state voltage drop (3.3-4.2 V), low reverse leakage current (3×10^-6 A/cm²), and fast switching (30-70 ns) have been fabricated and characterized. Forward current-voltage measurements indicate a minimum ideality factor of 1.2 which confirms a recombination process involving multiple energy levels. Reverse leakage current exhibits a square root dependence on voltage below the punchthrough voltage where leakage currents of less than 3×10^-6 A/cm² are measured. Reverse recovery measurements are presented which indicate the presence of recombination at the junction perimeter where a surface recombination velocity of 2-8×10⁵ cm/s is found. These measurements also indicate drift layer bulk carrier lifetimes ranging from 74 ns at room temperature to 580 ns at 250°C     

Effects of trap-state density reduction by plasma hydrogenation inlow-temperature polysilicon TFT

The reduction of trap-state densities by plasma hydrogenation in n-channel polysilicon thin-film transistors (poly-TFTs) fabricated using a maximum temperature of 600°C has been studied. Hydrogenated devices have a mobility of ~40 cm²/V×5, a threshold voltage of ~2 V, an inverse subthreshold of ~ 0.55 V/decade, and a maximum on/off current ratio of 5×10⁸. The effective channel length decreases by ~0.85 μm after a short hydrogenation which may be attributed to the activation of donors at trap states near the source/drain junctions. Trap-state densities decrease from 1.6×10¹² to 3.5×10¹¹ cm^-2 after hydrogenation, concomitant with the reduction of threshold voltage. Using the gate lengths at which the trap-state densities deviate from the long-channel values as markets for the leading edge of passivation, the apparent hydrogen diffusivity is found to be 1.2×10^-11 cm²/s at 350°C in the TFT structure     

High performance poly-Si TFTs fabricated using pulsed laserannealing and remote plasma CVD with low temperature processing

Key technologies for fabricating polycrystalline silicon thin film transistors (poly-Si TFTs) at a low temperature are discussed. Hydrogenated amorphous silicon films were crystallized by irradiation of a 30 ns-pulsed XeCl excimer laser. Crystalline grains were smaller than 100 nm. The density of localized trap states in poly-Si films was reduced to 4×10¹⁶ cm^-3 by plasma hydrogenation only for 30 seconds. Remote plasma chemical vapor deposition (CVD) using mesh electrodes realized a good interface of SiO ₂/Si with the interface trap density of 2.0×10¹⁰ cm^-2 eV^-1 at 270°C. Poly-Si TFTs were fabricated at 270°C using laser crystallization, plasma hydrogenation and remote plasma CVD. The carrier mobility was 640 cm²/Vs for n-channel TFTs and 400 cm²/Vs for p-channel TFTs. The threshold voltage was 0.8 V for n-channel TFTs and -1.5 V for p-channel TFTs. The leakage current of n-channel poly-Si TFTs was reduced from 2×10^-10 A/μm to 3×10^-13 A/μm at the gate voltage of -5 V using an offset gate electrode with an offset length of 1 μm     

1.1 kV 4H-SiC power UMOSFETs

Silicon Carbide (4H-SiC), power UMOSFETs were fabricated and characterized from room temperature to 200°C. The devices had a 12-μm thick lightly doped n-type drift layer, and a nominal channel length of 4 μm. When tested under Fluorinert^TM at room temperature, blocking voltages ranged from 1.0 kV to 1.2 kV. Effective channel mobility ranged from 1.5 cm²/V.s at room temperature with a gate bias of 32 V (3.5 MV/cm) up to 7 cm²/V.s at 100°C with an applied gate bias of 26 V (2.9 MV/cm). Specific on-resistance (R_on,sp) was calculated to be as low as 74 mΩ.cm² at 100°C under the same gate bias     

10 A, 2.4 kV Power DiMOSFETs in 4H-SiC

We report the characteristics of large area (3.3 × 3.3 mm ²) high-voltage 4H-SiC DiMOSFETs. The MOSFETs show a peak MOS channel mobility of 22 cm²/V·s and a threshold voltage of 8.5 V at room temperature. The DiMOSFETs exhibit an on-resistance of 4.2 mΩ·cm² at room temperature and 85 mΩ·cm² at 200°C. Stable avalanche characteristics at approximately 2.4 kV are observed. An on-current of 10 A is measured on a 0.103 cm² device. High switching speed is also demonstrated. This suggests that the devices are capable of high-voltage, high-frequency, low-loss switching applications     

High current p/p+-diamond Schottky diode

Epitaxial p-type Schottky diodes have been fabricated on p⁺ -substrate. While the activation energy of the epitaxial layer conductivity is 390 meV, that of the substrate is only 50 meV. At forward bias the substrate conductivity dominates above 150°C, leading for a 5×10^-5 cm² area contact to a series resistance of 14 Ω at 150°C reducing to 8 Ω at 500°C. To our knowledge, this is the lowest series resistance reported so far for a diamond Schottky diode enabling extremely high current densities of 10³ A/cm and a current rectification ratio at ±2 V of 10⁵ making these diodes already attractive as high temperature rectifiers     

Turn-on process in 4H-SiC thyristors

Detailed turn-on measurements of 4H-Silicon Carbide (SiC) npnp thyristors are presented for a wide range of operating conditions. Comparisons with similarly-rated silicon and Gallium Arsenide thyristors show a superior rise time and pulsed turn-on performance of SiC thyristors. Rise time for a 400 V blocking voltage, 4 V forward drop (2.8×10³ A/cm²) SiC thyristor has been found to be of the order of 3-5 ns. Pulsed turn on measurements show a residual voltage of only 50 V when a current density of 10⁵ A/cm² (35 A) was achieved in 20 ns     

Positive flatband voltage shift in MOS capacitors on n-type GaN

GaN MOS capacitors were fabricated using silicon dioxide deposited by low-pressure chemical vapor deposition oxide at 900°C. The MOS capacitor flatband voltage shift versus temperature was used to determine a pyroelectric charge coefficient of 3.7 × 10⁹ q/cm²-K, corresponding to a pyroelectric voltage coefficient of 7.0 × 10⁴ V/m-K     

High quality SiO2/Si interfaces of poly-crystallinesilicon thin film transistors by annealing in wet atmosphere

A new post-metallization annealing technique was developed to improve the quality of metal-oxide-semiconductor (MOS) devices using SiO ₂ films formed by a parallel-plate remote plasma chemical vapor deposition as gate insulators. The quality of the interface between SiO₂ and crystalline Si was investigated by capacitance-voltage (C-V) measurements. An H₂O vapor annealing at 270°C for 30 min efficiently decreased the interface trap density to 2.0×10¹⁰ cm^-2 eV^-1, and the effective oxide charge density from 1×10 ¹² to 5×10⁹ cm^-2. This annealing process was also applied to the fabrication of Al-gate polycrystalline silicon thin film transistors (poly-Si TFT's) at 270°C. In p-channel poly-Si TFT's, the carrier mobility increased from 60-400 cm² V^-1 s^-1 and the threshold voltage decreased from -5.5 to -1.7 V     

Experimental demonstration of a buried-channel charge-coupleddevice in 6H silicon carbide

Fundamental operation of the first buried-channel charge-coupled device (BCCD) in 6H-SiC is presented. The n-type buried-channel was formed by ion implantation of nitrogen, and a double level overlapping-polysilicon-gate process was adapted to the SiC MOS system. An electron mobility of 200 cm²/Vs was measured in the channel, which is doped 1.6×10¹⁷ cm^-3. An eight-stage, four-phase BCCD shift register was operated in the pseudo-two-phase configuration at room temperature. At 5.5 kHz, the charge transfer efficiency is greater than 99.4%     

Au/Pt/Ti/Ni ohmic contacts to p-ZnTe

Ohmic contacts of Au/Pd/Ti/Ni to p-ZnTe show a minimum specific contact resistance of 10^-6 Ωcm² for a p-type doping level of 3×10¹⁹ cm^-3 and at an annealing temperature of 300°C. The Ni and Ti layers are very effective in improving the electrical properties of these contact