Color‐breakup evaluation of spatio‐temporal color displays with two‐ and three‐color fields

Abstract— Spatio‐temporal color displays have higher transmission and resolution than conventional LCDs, but suffer from color breakup. In this paper, a 120‐Hz display with two‐color filters and two‐color fields is described and the amount of color breakup is compared with that of a 180‐Hz full‐color‐sequential display with no color filters and three‐color fields. The results indicate that color breakup in a color‐filterless display is annoying, whereas it is just visible in displays with two‐color filters even though the refresh rate is much lower.     

Image content adaptive color breakup index for field sequential color displays using a dominant visual saliency method

An index that can predict the perceptual visibility of color breakup for varying image content is valuable in field sequential color displays, whereas the current indices are usually for fixed patterns. To solve this problem, an image database containing 25 diverse reference images and 125 test cases with various color breakup visibility was first established. Next, visual experiments using a 240‐Hz liquid crystal display were performed to acquire the subjective color breakup scores of the test cases. A theorem based on visual saliency theory was proposed that the color breakup perception is mainly determined by the image regions with visual saliency values higher than a certain threshold, called the dominant visual saliency regions. A computational model based on this theorem was developed to obtain objective color breakup scores of the test cases from retinal images with and without color breakup. An analysis of the objective and subjective results revealed a Pearson linear correlation coefficient as high as 0.82, which matches the top‐level image quality assessment algorithms. Finally, the proposed color breakup index was used to benchmark against several mainstream field sequential color algorithms to determine their performances in color breakup suppression.     

A novel spectrum‐sequential display design with a wide color gamut and reduced color breakup

Abstract— The advantage of RGB color‐sequential displays is that they have no color filters, but the disadvantage is that they need to run at high refresh rates (> >180 Hz) to prevent flicker and color breakup. An alternative color‐sequential display, which can operate at relatively low refresh rates (～ 100 Hz) without disturbing color breakup or flicker, has been developed. The display has two color filters per pixel (cyan and magenta) on the LCD panel and the backlight can generate two types of spectra (blue‐green and green‐red), which results in a wide gamut four‐primary display, effectively. One part of the paper describes the color reproduction, including color‐filter design, gamut mapping, and multi‐primary conversion. The other part deals with the reduced perception of color breakup on the novel spectrum‐sequential display compared to conventional color‐sequential displays.     

A field‐sequential‐color display with a local‐primary‐desaturation backlight scheme

Abstract— Field‐sequential‐color technology eliminates the need for color filters in liquid‐crystal displays (LCDs) and results in significant power savings and higher resolution. But the LCD suffers from color breakup, which degrades image quality and limits practical applications. By controlling the backlight temporally and spatially, a so‐called local‐primary‐desaturation (LPD) backlight scheme was developed and implemented in a 180‐Hz optically compensated bend (OCB) mode LCD equipped with a backlight consisting of a matrix of light‐emitting diodes (LEDs). It restores image quality by suppressing color breakup and saves power because it has no color filter and uses local dimming. A perceptual experiment was implemented for verification, and the results showed that a field‐sequential‐color display with a local‐primary‐desaturation backlight reduced the color breakup from very annoying to not annoying and even invisible.     

A new field‐sequential‐color LCD without moving‐object color break‐up

Abstract— A new display method for field‐sequential‐color liquid‐crystal displays (FS‐LCDs) that reduces the negative effects of color break‐up associated with moving objects has been developed. The method is called Adjustment of Color Element on the Eyes (ACE), and it relies on the position on the eyes of RGB color sub‐images. It was confirmed that color break‐up also does not occur for peripheral objects when using ACE.     

Full‐color AMOLED with RGBW pixel pattern

Abstract— A full‐color AMOLED display with an RGBW color filter pattern has been fabricated. Displays with this format require about one‐half the power of analogous RGB displays. RGBW and RGB 2.16‐in.‐diagonal displays with average power consumptions of 180 and 340 mW, respectively, were characterized for a set of standard digital still camera images at a luminance of 100 cd/m². In both cases, a white‐emitting AMOLED was used as the light source, and standard LCD filters were used to provide the R, G, and B emission. The color gamuts of these displays were identical and the higher overall efficiency of the RGBW format results from two factors. First, a large fraction of a typical image is near neutral in color and can be reproduced using the white sub‐pixel. Second, the white sub‐pixel in an RGBW AMOLED display is highly efficient because of the absence of any color filter. The efficiency of these displays can be further enhanced by choosing a white emitter optimized to the target display white point (in this case D65). A two‐emission layer configuration based upon separate yellow and blue‐emitting regions is shown to be well suited for both the RGBW and RGB formats.     

Multi‐color LC/BL algorithm in field‐sequential‐color LCD for color‐breakup suppression

Abstract— The proposed liquid‐crystal and backlight (LC/BL) algorithm presents the dynamic field‐sequential‐color (D‐FSC) algorithm to reduce the color‐breakup (CBU) effect without greatly increasing the subframe rate. The D‐FSC algorithm can intelligently select one adequate color sequence from multiple color sequences according to the image data. In other words, the scope of CBU suppression of the proposed LC/BL algorithm is more extensive than other conventional FSCs. Simulation results show that the CBU suppression can be improved substantially by the proposed evaluation equation.     

A novel field‐sequential blue‐phase‐mode AMLCD

Abstract— Through the realization of a blue‐phase‐mode (hereinafter, the operational mode of liquid crystal having a blue phase is referred to as a blue‐phase mode), a display using an improved field‐sequential method was confirmed to be capable of display at a frame rate of 180 fps (field frequency of 540 Hz) or higher. Under this condition, an image without annoyance caused by color breakup was obtained. Moreover, a novel field‐sequential AMLCD integrated with a scan driver by combining the liquid‐crystal‐display (LCD) technology using blue phase and oxide‐semiconductor technology has been developed.     

The luminance resolution characteristics of multi‐primary‐color display

Abstract— In this paper, the resolution characteristics of multi‐primary‐color (MPC) display systems are analyzed. That four‐primary‐color (4PC) displays can increase the effective resolution for achromatic images in the luminance domain by a factor of two as compared to conventional RGB‐based displays with MPC‐specialized subpixel rendering, which is proposed in this paper, is demonstrated. Five‐ and six‐primary‐color (5PC and 6PC) display systems can reproduce denser luminance data than conventional RGB‐based display systems and solve a problem of MPC displays, viz. an increase of production costs and a decrease in the aperture ratio caused by increasing the number of subpixels in one pixel. This is an essential advantage of MPC display systems, which is related to the combination of the proposed color‐filter architecture and image processing. Thus, a completely new advantage of MPC display systems, in addition to their well‐known capabilities of color reproduction and power saving, is proposed.     

A full‐color eyewear display using planar waveguides with reflection volume holograms

Abstract— A full‐color eyewear display with over 85% see‐through transmittance with a 16° horizontal field of view was developed. Very low color crosstalk, less than 0.008 Δu′v′ uniformity, and 120% NTSC color gamut were achieved. Waveguides with two in‐ and out‐coupling reflection volume hologram elements enabled a simple configuration that has an optical engine beside the user's temples. The reflection volume hologram elements used on the waveguides realized a small thickness of 1.4 mm for each waveguide, and an out‐coupling reflection volume hologram used as an optical combiner contributed a high see‐through transmittance of 85% due to its wavelength selectivity. However, there are technical challenges in achieving a reasonable screen size and quality color images with optics that utilize holographic waveguides because holograms have large chromatic dispersions compared to conventional optical elements such as lenses and mirrors. Approaches to overcome these issues are described.     

Simulation of color breakup based on measured display temporal responses

Based on the measured temporal luminance behavior of each field, the perceived color breakup (CBU) artifact for moving block on a field sequential color display is simulated and predicted. The prediction accuracy is evaluated by a perceptual experiment on a 240 Hz liquid crystal display. The results show a perfect matching between the simulation and the subjects' actual visual experience. The simulation also works well when motion compensation is applied. It is validated by another perceptual experiment that a perfect or a near‐perfect compensation degree can suppress CBU significantly in field sequential color system. CBU of nature image was also simulated and reproduced for both stable and pulse backlight by using this model, which could be rather valuable for the further development of CBU metrics.     

Suppression of color breakup in color‐sequential multi‐primary projection displays

Abstract— Field‐sequential projection displays exhibit a phenomenon of color breakup (Rainbow effect). This is considered to be a disturbing artifact with negative marketing impact. The results of a psychophysical experiment comparing the visibility of the phenomenon in RGB and multi‐primary displays is described. Surprisingly, it is found that color breakup in color‐sequential projection displays with five primaries is equally (for 75 Hz) or less (for 105 Hz) visible than in similar displays with three primaries (at 180 Hz), despite the lower refresh rates.     

Power‐saving primary design for displays enclosing a target color gamut

Abstract— Display primaries are optimized for the trade‐off between the total primary power and color gamut under the requirement that a target color gamut is enclosed by the color gamut of the display. LED displays and HDTV color gamut are taken as examples. Compared to the display using a set of typical commercial RGB LEDs, it was found that a total optical (electrical) power of 23.6% (15.6%) can be saved for the display using optimal RGB LEDs. Although the size of the display color gamut is sacrificed, the color gamut of the display using optimal RGB LEDs still encloses the HDTV color gamut. The combined effect of the LED luminous efficiency and white‐point condition on the determination of the optimal LED wavelengths and bandwidths is also studied.     

Hybrid spatial‐temporal color synthesis and its applications

Abstract— A novel approach of synthesizing display color by hybrid color processing in both the spatial and temporal domains is introduced. The rational basis for this approach is found in vision science, and more particularly in the spatial and temporal characteristics of the human visual system. Various examples of the new approach, aiming at different display‐performance objectives, are described. Hybrid spatial‐temporal color synthesis can be used to generate a three‐primary RGB display, the analysis of which reveals a higher spatial resolution and a lower fixed‐pattern noise. The concept has also been used to build, based on a conventional LCD panel in combination with an adapted backlight system, a six‐primary LCD TV with a 22% wider color gamut. Finally, the approach is demonstrated in a four‐primary mobile LCD and results in lower cost combined with a higher display luminance and a wider color gamut.     

A novel driving method and device to reduce color breakup in color‐sequential displays

Abstract— Color‐sequential displays offer a better luminous efficiency, a higher spatial resolution, and a lower cost than conventional displays. However, a common problem is that visual effects cause color edge‐blurring of a moving picture, a phenomenon called color breakup or rainbow effects. Most driving methods, such as increasing the frame rate and inserting a black/white frame or another color sub‐frame to reduce the color breakup in color sequential displays has been presented in many papers, but every method has some limitations and problems. An innovative driving method and device to reduce the color‐breakup phenomenon will be demonstrated in this paper, designed without increasing the driving frequency. Instead, the brightness is increased by one third at the very least. Our method divides the driving frequency into four sub‐frames (WRGB), which is operated at 180 Hz compared to 240 Hz for conventional driving. Our result shows that the image quality is improved. The color‐breakup simulation based on “eye trace integration” and compensated white light will also be presented in this paper.     

Sequential‐color LCD based on OCB with an LED backlight

We have fabricated a 13.3‐in. XGA (1024 × 768) TFT sequential‐color liquid‐crystal display using optically compensated birefringency (OCB), illuminated by an LED backlight. We fabricated the sequential‐color display feasible process technology, and examined the performance and potential of a field‐sequential‐color scheme. The display was connected to a laptop computer and examined for flicker.     

A time‐sequential multi‐projector autostereoscopic display

Abstract— We describe a new 28‐view 25‐in. autostereoscopic display that combines both time‐sequential and multi‐projector technology. It is constructed from four time‐sequential subsystems, which abut behind a single ferroelectric liquid‐crystal shutter. The display has a resolution of 512 × 384 pixels in 24‐bit color. It allows multiple viewers to simultaneously view stereoscopic images without the need for special glasses or headgear.     

High‐performance OCB‐mode field‐sequential‐color LCD

Abstract— Optically compensated bend (OCB) mode is a promising technology for future high‐quality display devices due to its wide viewing angle without gray‐scale inversion and color shift, fast response time, high contrast ratio, and wide temperature range. This paper summarizes the developments of the OCB mode and the optical performance of OCB‐mode field‐sequential‐color LCD.     

High‐luminance 1.8‐mm‐pixel‐pitch CNT‐FED for ubiquitous color character displays

Abstract— A high‐luminance 1.8‐mm‐pixel‐pitch CNT‐FED for color character displays has been developed. The display panel has 32 × 256 color pixels, and the subpixel size is 0.6 × 1.8 mm. The display panel can provide good visibility when installed even in outdoor locations. The power consumption is low enough for the display to be battery driven. The practical application is the display of important messages regarding the evacuation from disaster areas, even under emergent no‐power conditions similar to the messages on vending machines.     

A4‐sized flexible ferroelectric liquid‐crystal displays with micro color filters

Abstract— We demonstrated an A4‐paper‐sized flexible ferroelectric liquid‐crystal (FLC) color displays fabricated by using a new plastic‐substrate‐based process which was developed for large‐sized devices. Finely patterned color filters and ITO electrodes were formed on a plastic substrate by a transfer method to avoid surface roughness and thermal distortion of the substrate, which induce disordering of the FLC molecular alignment. The thickness of an FLC/monomer solution sandwiched by two plastic‐film substrates was well controlled over a large area by using flexographic printing and lamination techniques. Molecular‐aligned polymer walls and fibers were formed in the FLC by a two‐step photopolymerization‐induced phase‐separation method using UV‐light irradiation. A fabricated A4‐sized flexible‐sheet display for color‐segment driving was able to exhibit color images even when it was bent.