冷轧压下率对无抑制剂取向硅钢初次再结晶退火的影响

对无抑制剂取向硅钢不同压下率下初次再结晶退火后的显微组织、宏观织构和微观织构进行了研究.结果表明,冷轧板织构主要为α取向线{001}＜110＞、{112}＜110＞和{111}＜110＞织构以及γ取向线{111}＜110＞织构.初次再结晶退火后,α取向线织构减弱,织构主要为γ取向线{111}＜112＞织构.随冷轧压下率的增加,冷轧和初次再结晶织构强度增加.当压下率为88％时,初次再结晶退火后 Goss 织构和{111}＜112＞织构强度最高,最有利于发生二次再结晶.EBSD 分析显示,Goss 取向晶粒大多与{111}＜112＞取向晶粒相邻.提高冷轧压下率,Goss取向晶粒和{111}＜112＞取向晶粒都增加,Goss 取向晶粒偏离理想取向角度减少.     

退火温度和时间对冷轧无取向硅钢组织与织构的影响

针对冷轧无取向硅钢退火工艺的特点,研究了退火温度和保温时间对成分为0.004%C、0.33%Si的冷轧无取向硅钢晶粒组织和织构演变的影响.结果表明:退火后,α线上{100}织构密度明显减弱,取向从{112}〈110〉向{111}〈112〉大量聚集;适当增加保温时间有助于提高{100}〈hkl〉织构,900℃、保温180 s,水冷得到的织构分布比较均匀,{001}面织构占有率比较高.     

冷轧Ti-IF超深冲钢罩式退火机理及织构变化规律的研究

在480~750℃条件下,模拟罩式退火,利用光学显微镜、X射线衍射和金相显微硬度计研究了冷轧Ti-IF超深冲钢晶粒结构的变化,通过取向密度函数分析了再结晶过程织构演变规律。研究表明:冷轧Ti-IF超深冲钢的再结晶温度约为630℃,再结晶过程能够在660℃条件下2 h之内完成;冷轧后该钢主要有4种织构,分别是{001}〈110〉、{111}〈110〉、{111}〈112〉和{112}〈110〉;在退火再结晶过程中,{111}逐渐转变为γ-{111},当退火温度升至720℃时,{001}〈110〉和{112}〈110〉转变为纤维织构γ-{111},最终{111}〈110〉和{111}〈112〉成为主要织构类型。     

冷轧压下率对连续退火Ti-IF钢组织和织构的影响

以工业生产的Ti-IF钢热轧板为研究材料,结合连续热镀锌线的工艺特点,采用实验室冷轧、盐浴退火方法和金相、X射线织构测试等分析手段,研究了冷轧压下率对组织和织构的影响规律。试验结果表明,随着冷轧压下率从60%提高到90%,冷轧态α取向线上的取向密度不断增强,而且主要形成了{223}110和{114}110织构,γ线上的{111}110和{111}112织构亦有所增强;退火后铁素体晶粒尺寸从9.0级细化到10.5级;试验钢退火后仍具有较强的{223}110和{114}110织构,且随着冷轧压下率的提高,{111}织构有增强的趋势。要获得强的{111}织构,冷轧压下率需在80%以上。     

退火工艺对DC04汽车板再结晶组织和织构的影响

以酒钢CSP工艺DC04冷轧汽车板为原料,通过实验室模拟退火工艺,采用OM、EBSD、ODF技术,研究退火工艺对其组织和织构特征的影响。结果表明,DC04汽车板退火组织为铁素体和少量渗碳体,575℃退火1h再结晶开始,730℃退火1h后再结晶较为充分,并随着退火时间的延长,铁素体晶粒长大。不同压下率的DC04冷轧板和退火板中,主要织构均为bcc金属中典型的α(<110>//RD)纤维织构和γ（<111>//ND）纤维织构。随着压下率增加,{111}<112>织构的取向密度明显大于{111}<110>织构的取向密度。730 ℃退火后,低压下率67%的退火板织构中有微弱的{001}<110>取向,但随着压下率增大,这种织构逐渐消失,而形成较强的{111}<112>、{111}<110>有利织构。增加变形量有利于获得有利的{111}织构而抑制不利{001}织构的生成,从而提高DC04的深冲性能。     

50W600 冷轧无取向电工钢退火过程组织和织构取向的演变

通过金相和电子背散射衍射法(EBSD)研究50W600冷轧无取向电工钢(0.003%～0.008%C、0.3%Si)在700～760℃3～360 s退火水冷时的组织和织构取向演变.结果表明,随退火温度的提高,钢的再结晶率和晶粒尺寸增大,740℃退火时,当保温时间由10 s增加至360 s,再结晶率由22.5%提高到100%,平均晶粒尺寸由3.08μm增大至17.17 μm.同时再结晶织构a线的取向密度下降,在15 8时{001}<110>、{112}<110>、{111}<110>、{110}<110>的取向密度均为1.5左右,y线上{111}<011>和{111}<112>的取向密度稳定在0.25左右.     

退火工艺对3.15 % Si冷轧无取向硅钢组织和织构的影响

试验研究了退火温度（850~950℃）和时间（5~18 min）对2.3 mm热轧硅钢板（/%:0.036C,3.15Si,0.21Mn,0.005P,0.007S,0.032Al）6道次轧制的0.35 mm冷轧板组织和织构的影响。结果表明,退火温度越高,晶粒平均尺寸越大,900℃5 min退火时平均晶粒尺寸41.39μm,试样织构主要集中在γ取向线上的{111}＜112＞;织构组分和{111}＜110＞;织构组分;900℃18 min退火时平均晶粒尺寸为48.08μm,试样的{111}面织构和{112}面织构密度都明显减弱,{001}面织构增强,磁性能较优。     

再结晶阶段加热速度对低碳冷轧板罩式退火过程组织和织构的影响

在实验室条件下模拟CSP热轧板为基板生产的低碳冷轧板罩式退火过程,研究再结晶阶段加热速度对冷轧板罩式退火过程组织和织构的影响。结果表明,压下率83.3%的冷轧板,随着再结晶阶段加热速度的增加,会使试样再结晶温度降低,再结晶过程提前完成,{001}110织构变强,{111}110织构先减少后增加,{111}112织构先减少后增加出现峰值,当加热速度超过50℃/h时又减小。在加热速度30~40℃/h间变形织构{112}110有较低的密度值。再结晶阶段加热速度40℃/h的退火工艺成品组织为饼形晶粒,{001}110织构密度较低,{111}110和{111}112密度较强,密度值接近。     

“ASP+罩式退火工艺”生产Ti-IF钢的织构演变

对济钢"ASP+罩式退火工艺"下生产的Ti-IF钢的热轧、冷轧及退火试样的织构演变进行分析。借助XRD测定并计算了热轧、退火及冷轧试样的取向分布函数和相关织构组分的体积分数。结果发现,济钢Ti-IF钢热轧板形成了较强的{111}面织构;在冷轧和退火后γ纤维织构显著增强;冷轧织构在罩式退火后,{111}<110>织构强度减弱,{111}<112>织构增强,{111}/{100}比值增加。     

低温板坯加热取向硅钢形变和初次再结晶织构的演变规律

 采用取向分布函数和取向线分析方法对低温板坯加热取向硅钢从热轧到初次再结晶工艺阶段的织构进行了研究。研究表明：一次冷轧后各层的织构组分与热轧板各层面的织构组分存在着继承关系,次表层存在很强的{001}<110>织构,中心层的织构和热轧板的中心层相似,存在强的{001}<110>和{112}<110>织构;中间退火后发生再结晶,各织构组分的强度有所减弱,Goss织构组分再次出现;二次冷轧后沿厚度方向上的织构不均匀性不明显,{111}<112>织构强度最高,几乎是其他织构组分的1倍,{001}<110>织构大幅降低;初次再结晶后织构沿厚度方向没有明显的不均匀性,{111}<110>为最强的织构组分,并且具有一定强度的Goss位向。     

China's Major Non-ferrous Metals Imports & Exports

正~~     

Zinc Production by Province in 2014

正~~     

80% of Chinese Firms Purchasing Overseas Mines Ended up in the Red

<正>Minmetals Resources acquired the world’s largest copper mine under construction for USD5.85 billion.One after another,listed companies Jien Nickle,China Molybdenum and Chihong Zinc and Germanium raised money to get involved in overseas mining projects…SOEs and private enterprises are engaged in a frenzy of overseas mine purchasing.A reporter with Economic     

Copper Processing Profit Dropped Sharply,Copper Consumption Will Face Impact in the Second Half of the Year

正Judging from China’s copper consumption field,the biggest consumption unit is electric power,which accounts for 47%of total consumption;it is followed by light industry sector,including household electrical appliance,machinery,durable goods and hardware etc,which accounts for 22%of total consumption;followed by transportation field,     

Central Geological Prospecting Fund Newly Added 16.47 Million Tonnes of Bauxite in 2013

正In 2013,the Central Geological Prospecting Fund(CGPF)Project newly discovered 15 ore fields,including 3 large above ore fields,and 5medium sized ore fields.The reporter learned from the recently published"Annual Report of Central Geological Prospecting Fund Project(2013)"that,from 2006 to 2013 the CGPF     

Manufacturers of Copper Tube for Central Air Conditioner Use Face Mounting Pressure in the Final Quarter of the Year

正This year,the investment growth rate of real estate industry continued to slow down,sold area of commercial housing also dropped significantly,which brought huge pressure to the domestic air conditioning manufactures.In the first half of the year,by relying on high growth in national financial expenditure,along with investment in public infrastructure     

Xinjiang Ranks No.1 in Production of Primary Aluminum in China

正Kang Yi,Honorary Chairman of China Nonferrous Metals Industry Association,said recently at the Forum on Development of the Non-ferrous Metals Industry in Central and Western China held in Zhengzhou that,as more and more electrolytic aluminum factories in Xinjiang came into operation,the electrolytic aluminum output of Xinjiang had reached2,275,000 tons in the first 7 months this year,     

Shenhuo Coal Industry and Electricity Power Completed800,000 t/a Aluminum Project in Xinjiang

正"Xinjiang project has been completed according to schedule,but total completion and total start of production are two different concepts,after completion it still needs a gradual process of reaching production target."On the morning of November 3,Shenhuo Coal Industry and Electricity Power told investors the above statement on the investor interaction platform.     

Guangdong Metal Transaction Center has Become the Second Largest Precious Metal Transaction Platform Nationwide

正The reporter learned from Guangdong Province Precious Metal Transaction Center that in 2013the Center maintained healthy development momentum,and had become the second largest precious metal transaction platform in China in terms of market size;currently Guangdong is quickening steps of financial innovation for the Center,aiming to build a transaction center with international core competitiveness.     

Seven Rare Earth Projects Involving Close to 3 Billion Yuan Investment Landed In the HighTech Zone

正On May 22,Baotou Rare Earth Industry Cooperation Consultation MeetingProject Agreement-signing Ceremony was held in Ningbo,nearly 40 enterprises from Ningbo,Guangdong,Hunan,and Shanxi participated in project consultation.After multi-lateral communication,agreements were signed for a total of 7 rare earth projects successfully.