Influence of adding Mesocarbon Microbeads into C/C composites on microstructure and properties during carbonization

This work tests the effect on microstructure, flexural strength, flexural moduli, plus the electrical and thermal conductivity of carbon/carbon composites with Mesocarbon Microbeads (MCMBs) content ranging 0–30% by weight during carbonization. These composites were reinforced by oxidative PAN Base fiber felts, and matrix precursor was resol‐type‐phenolic resin. MCMBs with a weight fraction of 0–30% were added to the matrix to elucidate the effect. Liquid‐phase impregnation was applied to reinforce matrix carbon. Cured composites were stabilized at 230°C, then heat‐treated at 400, 600, 800, 900 and 1000°C for carbonization. The measured flexural strength after heat‐treated at 1000°C was 51.20, 49.59, 43.55, and 38.76 MPa for MCMBs with 0, 10, 20, and 30% added to composites; mean flexural moduli were l.73, 1.24, 0.73, and 0.57 MPa, respectively. Adding MCMBs reduced both strength and modulus because of cracks and avoids caused by different shrinkage between resin and MCMBs; adding 30 wt % MCMBs raised thermal conductivity of C/C composites from 1.55 to 1.78 W/mK and reduced electric resistivity from 1.8 × 10^?2 to 5.97 × 10^?3 Ω cm. effect. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3102–3110, 2006     

Electrical and thermal conductivity and tensile and flexural properties of carbon nanotube/polycarbonate resins

Adding conductive carbon fillers to insulating thermoplastic polymers increases the resulting composite's electrical conductivity. Carbon nanotubes (CNTs) are very effective at increasing composite electrical conductivity at low loading levels without compromising composite tensile and flexural properties. In this study, varying amounts (2–8 wt %) of CNTs were added to polycarbonate (PC) by melt compounding, and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile and flexural properties. The percolation threshold was less than 1.4 vol % CNT, likely because of CNTs high aspect ratio (1000). The addition of CNT to PC increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 6 wt % (4.2 vol %) CNT in PC resin had a good combination of properties for electrical conductivity applications. The electrical resistivity and thermal conductivity were 18 Ω‐cm and 0.28 W/m · K, respectively. The tensile modulus, ultimate tensile strength (UTS), and strain at UTS were 2.7 GPa, 56 MPa, and 2.8%, respectively. The flexural modulus, ultimate flexural strength, and strain at ultimate flexural strength were 3.6 GPa, 125 MPa, and 5.5%, respectively. Ductile tensile behavior is noted in pure PC and in samples containing up to 6 wt % CNT. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

High thermal conductive m‐xylylenediamine functionalized multiwall carbon nanotubes/epoxy resin composites

In this study, multiwall carbon nanotubes (MWNTs) functionalized by m‐xylylenediamine is used as thermal conductive fillers to improve their dispersibility in epoxy resin and the thermal conductivity of the MWNTs/bisphenol‐A glycidol ether epoxy resin composites. Functionalization with amine groups of MWNTs is achieved after such steps as carboxylation, acylation and amidation. The thermal conductivity, impact strength, flexural strength, and fracture surfaces of MWNTs/epoxy composites are investigated with different MWNTs. The results show that m‐xylylenediamine is successfully grafted onto the surface of the MWNTs and the mass fraction of the organic molecules grafted onto MWNTs is about 20 wt %. The thermal conductivity of MWNTs/epoxy composites is further enhanced to 1.236 W/mK with 2 wt % m‐MWNTs. When the content of m‐MWNTs is 1.5 wt %, the impact strength and flexural strength of the composites are 25.85 KJ/m², 128.1 MPa, respectively. Scanning electron microscope (SEM) results show that the fracture pattern of composites is changed from brittle fracture to ductile fracture. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41255.     

Development and application of triglyceride-based polymers and composites

Triglyceride oils derived from plants have been used to synthesize several different monomers for use in structural applications. These monomers have been found to form polymers with a wide range of physical properties. They exhibit tensile moduli in the 1–2 GPa range and glass transition temperatures in the range 70–120 °C, depending on the particular monomer and the resin composition. Composite materials were manufactured utilizing these resins and produced a variety of durable and strong materials. At low glass fiber content (35 wt %), composites produced from acrylated epoxidized soybean oil by resin transfer molding displayed a tensile modulus of 5.2 GPa, a flexural modulus of 9 GPa, a tensile strength of 129 MPa, and flexural strength of 206 MPa. At higher fiber contents (50 wt %) composites produced from acrylated epoxidized soybean oil displayed tensile and compression moduli of 24.8 GPa each, and tensile and compressive strengths of 463.2 and 302.6 MPa, respectively. In addition to glass fibers, natural fibers such as flax and hemp were used. Hemp composites of 20% fiber content displayed a tensile strength of 35 MPa and a tensile modulus of 4.4 GPa. The flexural modulus was ∼2.6 GPa and the flexural strength was in the range 35.7–51.3 MPa, depending on the test conditions. The flax composite materials had tensile and flexural strengths in the ranges 20–30 and 45–65 MPa, respectively. The properties exhibited by both the natural- and synthetic fiber-reinforced composites can be combined through the production of “hybrid” composites. These materials combine the low cost of natural fibers with the high performance of synthetic fibers. Their properties lie between those displayed by the all-glass and all-natural composites. Characterization of the polymer properties also presents opportunities for improvement through genetic engineering technology. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 703–723, 2001     

Electrical and thermal conductivity and tensile and flexural properties: Comparison of carbon black/polycarbonate and carbon nanotube/polycarbonate resins

Adding conductive carbon fillers to thermoplastic polymers increases the resulting composite's electrical conductivity. Carbon black (CB) is very effective at increasing composite electrical conductivity at low loading levels. In this study, varying amounts (2 to 10 wt %) CB were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile and flexural properties. These results were compared with prior work done for carbon nanotubes (CNT) in polycarbonate. The percolation threshold was ～ 2.3 vol % CB compared to between 0.7 and 1.4 vol % CNT. At 8 wt % filler, the CNT/PC composite had an electrical resistivity of 8 ohm‐cm compared to 122 ohm‐cm for the CB/PC composite. The addition of CB to polycarbonate increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 8 wt % (5.5 vol %) CB in polycarbonate composite had a good combination of properties for semiconductive applications. Ductile tensile behavior is noted in pure polycarbonate and in samples containing up to 8 wt % CB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Modification of a carbon/carbon composite with a thermosetting resin precursor as a matrix by the addition of carbon black

Carbon/carbon composites were made through the pyrolysis of stabilized PAN felt and phenolic resin with the addition of 5 or 10 wt % carbon black to the matrix and then heat treatment at 600–2500°C. The effects of adding carbon black to the matrix precursor on the physical properties, microstructure, and mechanical properties of the resultant composites were investigated. Adding carbon black not only reduced the weight loss but also limited the shrinkage of the resultant composites. Adding carbon black also accelerated the formation of carbon basal planes in the matrix. At 2500°C, the crystalline stacking height in the composite with 10 wt % added carbon black was 200% greater than that with no additive. The flexural strength of the composite also increased from 15 to 42 MPa (almost 300%). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 333–337, 2006     

Catalytic effect of iron oxide on carbon/carbon composites during graphitization

Coal tar pitch matrix was modified by addition of iron oxide in different proportions i.,e. 0, 1, 3 and 5% by weight. The matrix was used to develop carbon fibre reinforced composites heat treated to 1000 and 2500 °C, respectively. The catalytic effect of iron oxide was ascertained by measuring the physical properties viz. the inter layer spacing, thermal conductivity and flexural strength of the composites. Low concentrations of the catalyst resulted in improvement in the thermal conductivity of composites from 68 × 10⁻² W/m K for 0% to 127 × 10⁻² W/m K for 1% iron oxide concentration. The flexural strength of graphitized composites, however, showed a remarkable increase from 325 MPa for 0% to 450 MPa for 5% iron oxide concentrations. The increase in flexural strength was probably due to the development of large numbers of grain boundaries whereas the increase in the thermal conductivity was most likely due to larger crystallite size i.e. decreases in the interlayer spacing (d₀₀₂) of the graphitized composites.     

Synergistic effects of carbon fillers on tensile and flexural properties in liquid‐crystal polymer based resins

One emerging market for thermally and electrically conductive resins is bipolar plates for use in fuel cells. Adding carbon fillers to thermoplastic resins increases the composite thermal and electrical conductivity. These fillers have an effect on the composite tensile and flexural properties, which are also important for bipolar plates. In this study, various amounts of three different types of carbon (carbon black, synthetic graphite particles, and carbon fibers) were added to Vectra A950RX liquid‐crystal polymer. In addition, composites containing combinations of fillers were also investigated via a factorial design. The tensile and flexural properties of the resulting composites were then measured. The objective of this study was to determine the effects and interactions of each filler with respect to the tensile and flexural properties. The addition of carbon black caused the tensile and flexural properties to decrease. Adding synthetic graphite particles caused the tensile and flexural modulus to increase. The addition of carbon fiber caused the tensile and flexural modulus and ultimate flexural strength to increase. In many cases, combining two different fillers caused a statistically significant effect on composite tensile and flexural properties at the 95% confidence level. For example, when 40 wt % synthetic graphite particles and 4 wt % carbon black were combined, the composite ultimate tensile and flexural strength increased more than what would be expected from the individual additive effect of each single filler. It is possible that linkages were formed between the carbon black and synthetic graphite particles that resulted in improved ultimate tensile and flexural strength. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

环氧树脂/碳纳米管导热复合材料的制备与性能研究

采用先酸化再空气氧化的方法对碳纳米管（CNTs）进行了纯化处理,并制备了2种环氧树脂(EP)/CNTs导热复合材料。研究了不同含量的CNTs及纯化CNTs对复合材料的导热性能、冲击性能及弯曲性能的影响。结果表明,纯化处理后,CNTs表面的催化剂粒子和无定形碳被去除,得到了纯净CNTs;当纯化CNTs含量为1.5 %时(质量分数,下同),材料的冲击强度和弯曲强度最高,分别为24.95 kJ/m2、127.2 MPa;当纯化CNTs含量为1.5 %时,复合材料的热导率可达1.237 W/（m·℃）。     

Microstructures and mechanical properties of carbon/carbon composites reinforced with carbon nanofibers/nanotubes produced in situ

Using ferrocene as catalyst and toluene as the liquid precursor, carbon/carbon (C/C) composites were prepared by chemical liquid-vapor infiltration at 850-1100 °C. The microstructures and properties of C/C composites obtained with different ferrocene contents were studied. The results show smooth laminar and isotropic pyrocarbon are obtained after adding ferrocene to the precursor. Carbon nanofibers can be formed as the catalyst content is 0.3-1 wt.%. When the ferrocene content is 2 wt.%, multi-walled carbon nanotubes with the diameter about 20-90 nm are obtained together with carbon-encapsulated iron nanoparticles. After adding ferrocene to the precursor, the fracture modes of the composites change from brittle facture to tough fracture. The flexural strength of the composites is a maximum for 0.3 wt.% ferrocene in the precursor, higher than for ferrocene contents of 0, 0.5, 1 and 2 wt.%. The flexural modulus of the composites decreases after adding ferrocene to the precursor.     

Physicochemical characterization of the filler–matrix interface in elastomer‐encapsulated fly ash/polyester particulate composites

An attempt was made to improve the toughness of fly ash (FA)/general‐purpose unsaturated polyester resin (GPR) composites. Elastomer [styrene–butadiene rubber (SBR) or acrylic copolymer (AC)]‐encapsulated fillers (FA or CaCO₃) were made through the coagulation of the emulsified elastomer containing the filler with constant stirring. The elastomer‐encapsulated fillers were added to GPR at concentrations as high as 15 wt % to make FA/SBR or AC/GPR composites. The mechanical properties (i.e., the tensile strength, tensile modulus, tensile elongation, flexural strength, flexural modulus, impact strength, and hardness) of FA/GPR, FA/SBR/GPR, and FA/AC/GPR composites were studied. The tensile‐fractured surfaces of all the composites were studied with scanning electron microscopy. The thermal stability was studied with thermogravimetric analysis. An analysis of the results indicate that this modification technique is rather easy and more economical than the chemical modification of filler surfaces with functional silane coupling agents. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 171–184, 2005     

A hot-pressing reaction technique for SiC coating of carbon/carbon composites

A hot-pressing reactive sintering (HPRS) technique was explored to prepare SiC coating for protecting carbon/carbon (C/C) composites against oxidation. The microstructures of the coatings were analyzed by X-ray diffraction and scanning electron microscopy. The results show that, SiC coating obtained by HPRS has a dense and crack-free structure, and the coated C/C lost mass by only 1.84 wt.% after thermal cycles between 1773 K and room temperature for 15 times. The flexural strength of the HPRS-SiC coated C/C is up to 140 MPa, higher than those of the bare C/C and the C/C with a SiC coating by pressure-less reactive sintering. The fracture mode of the C/C composites changes from a pseudo-plastic behavior to a brittle one after being coated with a HPRS-SiC coating.     

Electrical and thermal phenomena in low-density polyethylene/carbon black composites near the percolation threshold

Low-density polyethylene (LDPE)/carbon black (CB) composites were fabricated via melt-compounding technique. The percolation threshold was found to be around 20 wt % CB, and an electrical network formed by conductive CB was proven by scanning electron microscopy investigation. Dielectric responses depicted an interfacial relaxation peak at 20 wt % CB content. LDPE/CB composites showed an electric field-dependent conductivity as and a hysteresis behavior around the percolation threshold region. The CB particles with high thermal conductivity increased the heat conductance of the LDPE/CB20 up to 56%. The dynamic mechanical analysis of the LDPE/CB composites exhibited a noticeable contribution of CB throughout the composites, increasing the storage and loss modulus. The physical interactions between CB particles in the filler network enhanced the thermal degradation of the LDPE/CB25 composite for more than 76°C. The maximum breakdown strength of the LDPE/CB composites appeared with an approximately 10% improvement for LDPE/CB5 than pure LDPE. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47043.     

Comparison of the Mechanical and Thermo-Mechanical Properties of Unfilled and SiC Filled Short Glass Polyester Composites

This paper presents a comparison between particulate filled (SiC particles) and unfilled glass polyester composites on the basis of their mechanical and thermo-mechanical properties. The results show that particulate filled composites have a decreasing trend in mechanical properties when compared to the unfilled glass polyester composites. In particulate filled composites, the tensile and flexural strength of the composites decrease with the addition of 10 wt.-% SiC particles but increase with 20 wt.-% SiC particles. In the case of the unfilled glass polyester composite, the tensile and flexural strength of the composites increase with an increase in the fiber loading. However, higher values of tensile strength and flexural strength of particulate filled glass polyester were found than that of the unfilled glass polyester composite. In the case of thermo-mechanical and thermal properties, the particulate filled composites show better dynamical and thermal properties when compared to the unfilled glass polyester composites. The mechanical and thermal properties (i.e. thermal conductivity) are also calculated using FE modeling (ANSYS software) and the results from this simulation shows good agreement with the experimental results.     

Influence of fly ash cenospheres on performance of coir fiber‐reinforced recycled high‐density polyethylene biocomposites

Recycled high‐density polyethylene (RHDPE)/coir fiber (CF)‐reinforced biocomposites were fabricated using melt blending technique in a twin‐screw extruder and the test specimens were prepared in an automatic injection molding machine. Variation in mechanical properties, crystallization behavior, water absorption, and thermal stability with the addition of fly ash cenospheres (FACS) in RHDPE/CF composites were investigated. It was observed that the tensile modulus, flexural strength, flexural modulus, and hardness properties of RHDPE increase with an increase in fiber loading from 10 to 30 wt %. Composites prepared using 30 wt % CF and 1 wt % MA‐g‐HDPE exhibited optimum mechanical performance with an increase in tensile modulus to 217%, flexural strength to 30%, flexural modulus to 97%, and hardness to 27% when compared with the RHDPE matrix. Addition of FACS results in a significant increase in the flexural modulus and hardness of the RHDPE/CF composites. Dynamic mechanical analysis tests of the RHDPE/CF/FACS biocomposites in presence of MA‐g‐HDPE revealed an increase in storage (E′) and loss (E″) modulus with reduction in damping factor (tan δ), confirming a strong influence between the fiber/FACS and MA‐g‐HDPE in the RHDPE matrix. Differential scanning calorimetry, thermogravimetric analysis thermograms also showed improved thermal properties in the composites when compared with RHDPE matrix. The main motivation of this study was to prepare a value added and low‐cost composite material with optimum properties from consumer and industrial wastes as matrix and filler. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42237.     

Preparation and properties of multi-walled carbon nanotube/carbon/polystyrene composites

Multi-walled carbon nanotube (MWCNT)/C/polystyrene (PS) composite materials were prepared by in situ polymerization of monomer in preformed MWCNT/C foams. MWCNT/C foams were preformed using polyurethane foam as template. The preformed MWCNT/C foams had a more continuous conductive structure than the carbon nanotube networks formed by free assembly in composites. The structure of the MWCNT/C foam network was characterized with scanning electron microscopy. The MWCNT/C/PS composites have an electric conductivity higher than 0.01 S/cm for a filler loading of 1 wt.%. Enhancement of thermal conductivity and mechanical properties by the preformed MWCNT/C foam were also observed.     

Mechanical, thermal and ablative properties of interply continuous/spun hybrid carbon composites

The mechanical and thermal properties of interply hybrid carbon fiber (continuous and spun fabric)/phenolic composite materials have been studied. Hybrid carbon/phenolic composites (hybrid CP) with continuous carbon fabric of high tensile, flexural strength and spun carbon fabric of better interlaminar shear strength and lower thermal conductivity are investigated in terms of mechanical properties as well as thermal properties.Through hybridization, tensile strength and modulus of spun type carbon fabric reinforced phenolic composites (spun CP) increased by approximately 28% and 20%, respectively. Hybrid CP also exhibits better interlaminar shear strength than continuous carbon fabric/phenolic composites (continuous CP).The in-plane thermal conductivity of hybrid CP is 4-8% lower than that of continuous CP. As continuous filament type carbon fiber volume fraction increases, the transversal thermal conductivity of hybrid CP decreases.The erosion rate and insulation index were examined using torch test. Spun CP has a higher insulation index than continuous CP and hybrid CP over the entire temperature range. Hybrid CP with higher content of spun fabric exhibits higher insulation index as well as lower erosion rate.     

Preparation and properties of multi‐walled carbon nanotubes/carbon fiber/epoxy composites

Multi‐walled carbon nanotubes/carbon fiber (MWCNTs/CF) hybrid fillers are employed to prepare MWCNTs/CF/epoxy composites. Results reveal that a great improvement of the thermal conductivities of the epoxy composites with the addition of MWCNTs/CF hybrid fillers, and the thermal conductivity of the MWCNTs/CF/epoxy composites is 1.426 W/mK with 8 vol% treated MWCNTs/CF hybrid fillers (5 vol% MWCNTs + 3 vol% CF). Both the flexural and impact strength of the MWCNTs/CF/epoxy composites are increased firstly, but decreased with the excessive addition of MWCNTs. The flexural and impact strength of the MWCNTs/epoxy composites are optimal with 2 vol% MWCNTs. For a given MWCNTs/CF hybrid fillers loading, the surface treatment of MWCNTs/CF hybrid fillers can further increase the thermal conductivities and mechanical properties of the MWCNTs/CF/epoxy composites. POLYM. COMPOS., 35:2150–2153, 2014. © 2014 Society of Plastics Engineers     

Floating catalyst chemical vapor infiltration of nanofilamentous carbon reinforced carbon/carbon composites – Integrative improvement on the mechanical and thermal properties

Nanofilamentous carbon (NFC) reinforced carbon/carbon composites were produced by floating catalyst chemical vapor infiltration with ferrocene content ranging 0–2.0?wt%. The NFCs and increased graphitization degree led to an improvement on the mechanical and thermal properties. An excellent combination of high strength and thermal conductivity (TC), and low coefficient of thermal expansion (CTE) was reached by adding 0.5–0.8?wt% catalyst. When the content exceeded 0.8wt%, the strength and TC were decreased by the limited NFC growth and matrix transited from rough laminar to isotropic pyrocarbon. After the treatment of 2500?°C, the strength and CTE decreased whereas the TC was increased. With the catalyst contents at 0.5–0.8?wt%, the flexural and shear strength retention ratios achieved a high value of 73.1–74.5 and 79.1–79.4%, respectively, and the in-plane and out-of-plane TCs exhibited maxima of 339.1 and 72.5?W/(m?K). Relatively low CTE was obtained at 2.0?wt% catalyst owing to the increased amount of cracks and pores.     

Development and characterization of green composites from bio‐based polyethylene and peanut shell

In the present work, different compatibilizers, namely polyethylene‐graft‐maleic anhydride (PE‐g‐MA), polypropylene‐graft‐maleic anhydride (PP‐g‐MA), and polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene‐graft‐maleic anhydride (SEBS‐g‐MA) were used on green composites derived from biobased polyethylene and peanut shell (PNS) flour to improve particle–polymer interaction. Composites of high‐density polyethylene/peanut shell powder (HDPE/PNS) with 10 wt % PNS flour were compatibilized with 3 wt % of the abovementioned compatibilizers. As per the results, PP‐g‐MA copolymer lead to best optimized properties as evidenced by mechanical characterization. In addition, best particle–matrix interface interactions with PP‐g‐MA were observed by scanning electron microscopy (SEM). Subsequently HDPE/PNS composites with varying PNS flour content in the 5–30 wt % range with PP‐g‐MA compatibilizer were obtained by melt extrusion and compounding followed by injection molding and were characterized by mechanical, thermal, and morphological techniques. The results showed that PNS powder, leads to an increase in mechanical resistant properties (mainly, flexural modulus, and strength) while a decrease in mechanical ductile properties, that is, elongation at break and impact absorbed energy is observed with increasing PNS flour content. Furthermore, PNS flour provides an increase in thermal stability due to the natural antioxidant properties of PNS. In particular, composites containing 30 wt % PNS powder present a flexural strength 24% and a flexural modulus 72% higher than the unfilled polyethylene and the thermo‐oxidative onset degradation temperature is increased from 232 °C up to 254 °C thus indicating a marked thermal stabilization effect. Resultant composites can show a great deal of potential as base materials for wood plastic composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43940.