Novolac resin–poly(ethyl methacrylate) interpenetrating polymer networks: Morphology and mechanical and thermal properties

Full interpenetrating networks (IPNs) and semi‐IPNs of Novolac (phenolic) resin and poly(ethyl methacrylate) (PEMA) were prepared by the sequential mode of synthesis. These were characterized with respect to their mechanical properties, that is, ultimate tensile strength (UTS), percentage elongation at break, modulus, and toughness. Thermal properties were studied by DSC and thermogravimetric analysis (TGA). The morphological features were studied through polarizing light microscopy (PLM). The effects of variation of the blend ratios on the above‐mentioned properties were examined. There was a gradual decrease of modulus and UTS with consequent increases in elongation at break and toughness for both types of IPNs with increasing proportions of PEMA. An inward shift and lowering (with respect to pure phenolic resin) of the glass‐transition temperatures of the IPNs with increasing proportions of PEMA were observed, thus indicating a plasticizing influence of PEMA on the rigid and brittle matrix of crosslinked phenolic resin. The TGA thermograms exhibit two‐step degradation patterns. Although there was an apparent increase in thermal stability at the initial stages, particularly at lower temperatures, a substantial decrease in thermal stability was observed in the regions of higher temperatures. The surface morphology as revealed by PLM clearly indicates two‐phase structures in all the full and semi‐IPNs, irrespective of PEMA content. The matrix–PEMA domain interfaces are quite sharp at higher concentrations of PEMA. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 412–420, 2003     

Engineering properties of Novolac resin‐PMMA{poly(methyl methacrylate)} IPN system

Full and semi interpenetrating polymer networks (IPNs) based on phenol‐formaldehyde resin (Novolac) and poly(methyl methacrylate) have been made by in situ sequential technique of IPN formation. These systems of different compositions were characterized with respect to their mechanical properties, such as, ultimate tensile strength (UTS), percentage elongation at break, modulus, and toughness. Thermal properties were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Extent of phase mixing of the two polymers was envisaged from the micrographs obtained by polarizing light microscopy (PLM). The effects of variation of the blend ratios on the above‐mentioned properties were examined. There was a decreasing trend of modulus and UTS with consequent increases in elongation at break and toughness for both types of IPNs with increase in proportions of PMMA. Lowering of glass transition temperatures (with respect to pure crosslinked Novolac resin) of the IPNs with increasing proportions of PMMA was observed, indicating a plasticizing influence of PMMA on the rigid and brittle matrix of phenolic resin. The TGA thermograms exhibit lowering in thermal stability of the IPNs with respect to pure phenolic resin in the regions of higher temperatures. With increase in proportion of PMMA the onset of degradation of the IPNs is shifted towards lower temperature zone. The surface morphology as revealed by PLM indicates distribution of discrete domains of PMMA in the phenolic resin matrix. The two phase interfaces are quite sharp at higher concentrations of PMMA. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2764–2774, 2004     

Synthesis and characterization of sequential interpenetrating polymer networks of novolac resin and poly(ethyl acrylate)

Interpenetrating polymer networks (IPN) of Novolac/poly(ethyl acrylate) have been prepared via in situ sequential technique of IPN formation. Both full and semi IPNs were characterized with respect to their mechanical properties that is, ultimate tensile strength (UTS), percentage elongation at break, modulus, and toughness. Physical properties of these were evaluated in terms of hardness, specific gravity, and crosslink density. Thermal behavior was studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The morphological features were observed by an optical microscope. There was a gradual decrease in modulus and UTS, with consequent increases in elongation at break and toughness for both types of IPNs with increasing proportions of PEA. An inward shift and lowering (with respect to pure phenolic resin) of the glass transition temperatures of the IPNs with increasing proportions of PEA were observed, thus, indicating a plasticizing influence of PEA on the rigid, brittle, and hard matrix of crosslinked phenolic resin. The TGA thermograms exhibit two‐step degradation patterns. An apparent increase in thermal stability at the initial stages, particularly, at lower temperature regions, was followed by a substantial decrease in thermal stability at the higher temperature region under study. As expected, a gradual decrease in specific gravity and hardness values was observed with increase in PEA incorporation in the IPNs. A steady decrease in crosslink densities with increase in PEA incorporation was quite evident. The surface morphology as revealed by optical microscope clearly indicates two‐phase structures in all the full and semi IPNs, irrespective of acrylic content. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Sequential interpenetrating polymer networks of novolac resin and poly(n‐butyl methacrylate)

Novolac resin/poly(n‐butyl methacrylate), P(n‐BMA), sequential interpenetrating polymer networks (both semi and full types) were prepared and characterization of the various compositions (up to 40% by weight of PF incorporation) was performed in terms of mechanicals, namely, ultimate tensile strength (UTS), percentage elongation at break (% E.B.), modulus, and toughness. Thermal properties were studied by differential scanning calorimetry and thermogravimetric analysis (TGA). Crosslink densities of the IPNs were calculated using Flory‐Rehner equation. The morphological features were studied through scanning electron microscope. There was a gradual decrease of modulus and UTS with consequent increases in % E. B. and toughness with increasing proportions of P(n‐BMA). An inward shifting and lowering of the glass transition temperatures of the IPNs (compared with that of pure phenolic resin) with increasing proportions of P(n‐BMA) were observed. The TGA thermograms exhibit two‐step degradation patterns. A typical cocontinuous bi‐phasic morphology is evident in the micrographs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4030–4039, 2006     

Sequential interpenetrating polymer networks of novolac resin and poly(2‐ethyl hexyl acrylate)—thermal,mechanical, and morphological study

Interpenetrating polymer networks (IPN) of novolac/poly (2‐ ethyl hexyl acrylate) (PEHA) have been prepared via in situ sequential technique of IPN formation. Full and semi‐IPNs were prepared with different blend ratios (w/w) e.g., 90 : 10, 80 : 20, and 70 : 30 in which the major constituent was novolac resin. A gradual decrease in specific gravity and hardness values was observed with increase in PEHA incorporation. A steady decrease in crosslink density with increase in PEHA fraction in the IPNs was quite evident. The IPNs were characterized with respect to their mechanical properties, e.g., ultimate tensile strength, percentage elongation at break, modulus, and toughness. Thermal behavior was studied by differential scanning calorimetry and thermogravimetric analysis. A plasticizing influence of PEHA on the rigid, brittle, and hard matrix of crosslinked phenolic resin is evidenced from the mechanical and thermal properties. The two‐phase surface morphology is revealed by scanning electron microscope. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Engineering properties of poly(vinyl chloride)–poly(butyl methacrylate) semi‐1 and semi‐2 interpenetrating polymer networks

Semi‐1 and semi‐2 interpenetrating polymer networks (IPNs) of poly(vinyl chloride) (PVC) and in situ formed poly(butyl methacrylate) (PBMA) have been synthesized using diallyl phthalate and ethylene glycol dimethacrylate as the crosslinkers of PVC and PBMA, respectively. These were then characterized with reference to their mechanical, thermal, and morphological properties. The mechanical and thermal characteristics revealed modification over the unmodified polymeric systems in relation to their phase morphologies. The semi‐1 IPNs displayed a decrease in their mechanical parameters of modulus and UTS while semi‐2 IPNs exhibited a marginal increase in these two values. The semi‐1 IPNs, however, also revealed a decrease in the elongation and toughness values away from the normal behavior. The thermomechanical behavior of both the systems is in conformity with their mechanicals in displaying the softening characteristics of the system and stabilization over unmodified PVC. The DSC thermograms are also correlated to these observations along with the heterogeneous phase morphology which is displayed by both the systems especially at higher concentration of PBMA incorporation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Epoxy–poly(butyl methacrylate) interpenetrating polymer networks: Morphology and various physical,mechanical, and thermal properties

Semi- and full interpenetrating polymer networks (IPNs) of epoxy resin and poly(butyl methacrylate) (PBMA) were prepared by the sequential mode of synthesis. These were characterized with respect to their mechanical properties, such as ultimate tensile strength, percent elongation at break, and modulus. The densities of these samples were evaluated and compared. Differential scanning calorimetry (DSC) and thermogravimetric analysis were undertaken for thermal characterization of the IPNs. Phase morphology was studied by polarized light microscopy of the undeformed specimens and by scanning electron microscopy of the fractured surfaces of samples undergoing tensile failure. The effects of variations of the blend ratios on the above-mentioned properties were examined. A gradual decrease in modulus and tensile strength was observed for both the semi- and full IPNs with consequent increases in elongation at break and toughness as the proportion of PBMA increased. The densities also followed the same pattern. Semi-IPNs, however, were characterized by higher densities, tensile strengths, and moduli than the corresponding full IPNs. The DSC tracings displayed broadening of transitions, indicating some phase blending. The percent weight retentions in the thermal decomposition of the IPNs and pseudo-IPNs were higher than that observed during the thermal degradation of the epoxy resin homopolymer network. Phase-separated PBMA domains of various sizes were presumed to be responsible for the increased toughness of PBMA-modified epoxy. © 1996 John Wiley & Sons, Inc.     

Epoxy/poly(methyl methacrylate) interpenetrating polymer networks—morphology,mechanical and thermal properties

Full and semi-IPNs were prepared from epoxy and poly methyl methacrylate (PMMA), by the sequential mode of synthesis and were characterized by measurements of ultimate tensile strength (UTS), elongation at break, modulus, and toughness. Aromatic polyamine adducts and ethylene glycol dimethacrylate were used as the crosslinkers for epoxy and comonomer/crosslinker for methyl methacrylate monomer, respectively. Higher UTS and modulus of the semi-IPNs over full IPNs were attributed to the higher probability of interpenetration. The weight retention in the thermal decomposition of the IPNs and semi-IPNs were higher than the epoxy homopolymer. This enhancement was presumably related to the presence of the unzipped methyl methacrylate monomer which acted as radical scavangers in the epoxy degradation. © 1994 John Wiley & Sons, Inc.     

Poly(2‐hydroxyethyl methacrylate) hydrogel: from a brittle material to a nanofilled semi‐interpenetrating polymer network with potential application in wound dressings

In this work we report the photopolymerization of poly(2‐hydroxyethyl methacrylate) (PHEMA) together with a hydrophilic chitosan derivate (carboxymethyl‐chitosan) to yield a semi‐interpenetrating polymer network (semi‐IPN) that was filled with poly(N‐vinylcaprolactam)/poly(ethylene glycol methacrylate) core–shell nanogels in order to enhance the mechanical properties of the resulting hydrogels. The mechanical properties of the nanofilled semi‐IPNs were found to be more suitable for wound dressing applications than the PHEMA hydrogel as described by dynamic mechanical analysis in dry form and submerged in water. This was evidenced by a higher Young's modulus and higher elongation at break in the semi‐IPNs compared to blank PHEMA hydrogels. Furthermore, when the hydrogels were filled with nanogels, there was an elongation at break similar to that of skin with only a slightly lower Young's modulus. © 2019 Society of Chemical Industry     

Semi‐ and full‐interpenetrating polymer networks based on polyurethane produced from canola oil and poly(methyl methacrylate)

Semi‐ and full‐interpenetrating polymer networks (IPNs) were prepared using polyurethane (PUR) produced from a canola oil‐based polyol with primary terminal functional groups and poly(methyl methacrylate) (PMMA). The properties of the material were studied and compared using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and tensile measurements. The morphology of the IPNs was investigated using atomic force microscopy (AFM). Semi‐IPNs demonstrated different thermal mechanical properties, mechanical properties, phase behavior, and morphology from full IPNs. Both types of IPNs studied are two‐phase systems with incomplete phase separation. However, the extent of phase separation is significantly more advanced in the semi‐IPNs compared with the full IPNs. All the semi‐IPNs exhibited higher values of elongation at break for all proportions of acrylate to polyurethane compared with the corresponding full IPNs. These differences are mainly due to the fact that in the case of semi‐IPNs, one of the constituting polymers remains linear, so that it exhibits a loosely packed network and relatively high mobility, whereas in the case of full IPNs, there is a higher degree of crosslinking, which restricts the mobility of the chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Epoxy resin–poly(ethyl methacrylate) interpenetrating polymer networks: Morphology,mechanical, and thermal properties

Full (interpenetrating networks (IPNs)) and semi-IPNs of the epoxy resin and poly(ethyl methacrylate) (PEMA) were prepared by the sequential mode of synthesis. These were characterized with respect to their mechanical properties, namely, tensile strength, elongation at break, modulus, and toughness. Thermal properties were studied by differential scanning calorimetry and thermogravimetry. The morphological features were studied through scanning electron microscopy (SEM) and polarized light microscopy. The effects of variation of the blend ratios on the above-mentioned properties were examined. There was a gradual decrease of modulus and tensile strength with consequent increases in elongation at break and toughness for both types of IPNs with increases in PEMA content. The weight retentions in the thermal decomposition of both the semi-IPNs and full IPNs were higher than the epoxy homopolymer. This enhancement was presumably related to the presence of the unzipped ethyl methacrylate monomer, which acted as radical scavengers in the epoxy degradation. An inward shift and lowering (with respect to pure epoxy) of the T_g of the IPNs was observed. The polarized light microscopy exhibits bimodal distribution of particle sizes. The fractography as studied by SEM shows change in fracture mechanics from shear yielding to crazing with increasing PEMA content. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:1051–1059, 1998     

Studies on morphology,mechanical, thermal,and rheological behavior of extrusion‐blended polypropylene and thermotropic liquid crystalline polymer

Polypropylene (PP) was melt‐blended in a single‐screw extruder with a thermotropic Vectra B‐950 liquid crystalline polymer (LCP) in different proportions. The mechanical properties of such blends were compared in respect of their Young's moduli, ultimate tensile strength (UTS), percent elongation at break, and toughness to those of pure PP. The thermal properties of these blends were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The morphology was studied by using a polarizing light microscope (PLM) and a scanning electron microscope (SEM) while the rheological aspects of the blends and the pure PP were studied by a Haake Rheowin equipment. Mechanical analysis (tensile properties) of the blends showed pronounced improvement in the moduli and the UTS of the PP matrix in the presence of 2–10% of LCP incorporation. TGA of all the blends showed an increase in the thermal stability for all the blends with respect to the matrix polymer PP, even at a temperature of 410°C, while PP itself undergoes drastic degradation at this temperature. DSC studies indicated an increase in the softening range of the blends over that of PP. Morphological studies showed limited mixing and elongated fibril formation by the dispersed LCP phase within the base matrix (PP) at the lower ranges of LCP incorporation while exhibiting a tendency to undergo gross phase separation at higher concentrations of LCP, which forms mostly agglomerated fibrils and large droplets. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 767–774, 2003     

Mechanical properties,thermal stability,and flame retardance of novolac‐type phenolic resin blended with poly(dimethylsiloxaneadipamide)

Mechanical properties (flexural strength, flexural modulus, and notched Izod impact strength), thermal stability, and flame retardance of poly(dimethylsiloxane adipamide) (PDMSA)‐toughened novolac type phenolic resin were investigated. Mechanical properties of modified novolac‐type phenolic resin increase with PDMSA contents, because the soft segment of PDMSA absorbs the loads in the network of brittle novolac‐type phenolic resins. TGA results show that the thermal degradation temperatures are higher than 400°C, and the temperature of 10% weight loss increases with increasing the PDMSA content. The char yield increases with novolac‐type phenolic resin content. The morphologies of the fracture surface of the modified novolac‐type phenolic resin were investigated by scanning electron microscopy (SEM). Morphological results agree with those from mechanical properties of the modified novolac‐type phenolic resin. The modified novolac‐type phenolic resin also shows excellent flame retardance that is UL‐94, V‐1, and the limited oxygen index is higher than 35. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 631–637, 2001     

Modification of the mechanical and thermal properties of PVC by semi IPN formation with poly(butyl acrylate)

Semi1 and semi2 interpenetrating polymer networks of poly(vinyl chloride) PVC and in situ formed poly(butyl acrylate) (PBA) have been synthesized and characterized using diallyl phthalate (DAP) and ethylene glycol dimethacrylate (EGDM) as the crosslinkers of PVC and PBA, respectively. These two types of IPNs have been compared with respect to their mechanical and thermal properties. The semi1 IPNs displayed a decrease in their mechanical parameters and the physical properties as well, while in contrast, the semi2 IPNs exhibited a marginal increase in the corresponding values when compared to the crosslinked PVC in the case of semi1 IPN and linear PVC in case of semi2 IPN. The representative samples of semi1 and semi2 IPNs revealed a two‐stage‐degradation typical of PVC while confirming the increased stability of the samples with higher onset temperature of degradation. The softening characteristics as detected by thermomechanical analysis are in conformity with their mechanicals. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

New interpenetrating polymer networks based on uralkyd–poly(butyl methacrylate)

A study on two‐component semi‐ and full‐interpenetrating polymer networks (IPNs) of soyabean‐oil based uralkyd resin (UA) and poly(butyl methacrylate) (PBMA) synthesized by a sequential technique, has been conducted. The IPNs obtained are characterized with respect to their mechanical properties, such as tensile strength, percentage elongation and hardness (Shore A). Phase morphology has been studied by scanning electron microscopy. Glass transition studies have been carried out using differential scanning calorimetry. The thermal characterization of the IPNs was undertaken with the aid of thermogravimetric analysis. The apparent densities of these samples have been determined and are compared. The effect of the compositional variation on the above‐mentioned properties was examined. The tensile strength exhibits a sudden rise (approximately three‐fold) for the semi‐ and full‐IPNs with composition UA: PBMA 40% : 60% compared with the UA:PBMA composition of 20% : 40%. © 2001 Society of Chemical Industry     

Interpenetrating polymer networks from castor oil based polyurethanes,XI

Under different experimental conditions, various liquid polyurethanes (PU) were synthesized from castor oil and isophorone diisocyanate varying NCO/OH ratio. These polyurethanes were then subsequently interpenetrated with n-butyl acrylate (nBA) monomer and ethylene glycol di-methacrylate as crosslinker by radical polymerization using benzoyl peroxide as an initiator. This leads to the formation of novel PU/PnBA interpenetrating polymer networks (IPNs) by transfer molding. These IPNs were characterized by their resistance to chemical reagents, thermal behavior (TGA), mechanical properties, namely; tensile strength, Young's modulus, elongation at break (%) and hardness (Shore A). The morphology of the IPNs was studied by Scanning Electron Microscopy. The dielectric behavior was computed in terms of electrical conductivities, dielectric constant (ε′), loss tangent (tan δ) and dielectric loss (ε″).     

Interpenetrating polymer network from castor oil-based polyurethanes and poly(methyl acrylate). XIV

Castor oil containing hydroxyl functionality was reacted with 4,4′-diphenylmethanediisocyanate under different stoichiometric ratios of NCO/OH to obtain liquid polyurethanes. These polyurethanes were subsequently interpenetrated with methyl acrylate monomer using ethylene glycol dimethacrylate as a crosslinker by radical polymerization using benzoyl peroxide as an activator. The polyurethane/poly(methyl acrylate) interpenetrating polymer networks (PU/PMA IPNs) were obtained as tough films by transfer molding techniques. All IPNs were characterized by their resistance to chemical reagents, optical properties, thermal behavior, and mechanical properties: tensile strength, Young's modulus, elongation at break (%) and hardness Shore A. The morphology of the IPNs was studied by scanning electron microscopy and dielectric properties: electrical conductivity (σ), dielectric constant (?′), dielectric loss (?″), and loss tangent (tan δ) at different temperatures.     

Investigation of rheological,mechanical, and thermal properties of nanocomposites based on nitrile rubber-phenolic resin reinforced with nanographene

In this study, nanocomposites of acrylonitrile butadiene rubber (NBR)/phenolic resin/graphene nanoparticles (GNPs) were prepared using a two-roll mill. According to the results, the addition of GNPs increased the scorch time, vulcanization time, and viscosity of the blends. By adding phenolic resin and in the presence of a higher percentage of acrylonitrile, the modulus and tensile strength increased and the elongation at break decreased. The mechanical properties of the nanocomposites improved with increasing the amount of nanoparticles. The addition of 1.5 phr GNP to the blends containing NBR with 33% and 45% acrylonitrile increased the tensile modulus by 56% and 49%, respectively. The tensile properties of the nanocomposites were also investigated at 50, 25, and 75°C. It was observed that with increasing the amount of nanoparticles, the deterioration of the mechanical properties at elevated temperatures was reduced. Also, thermal stability increased with increasing the amount of nanoparticles in all the samples.     

Studies on novel semi‐2‐IPNs from polyetherimide and citraconimide

A series of novel semi‐2‐interpenetrating polymeric networks (semi‐2‐IPNs) were prepared through blending in solution using two different polyimides, biscitraconamic acid as a precursor of biscitraconimide (MBMI) with various proportions of polyetherimide (PEI) to achieve optimum properties. Biscitraconamic acid was prepared by reacting citraconic anhydride (CA), 3,3',4,4'‐benzophenone tetracarboxylic dianhydride (BTDA) and bis(3‐aminopropyl)phenyl phosphine (BAPPP) and it was characterized by differential scanning calorimetry (DSC), FTIR, and ¹H‐NMR spectroscopy. Both biscitraconamic acid and PEI were blended in N,N‐dimethylacetamide (DMAc) solution, casted and thermally cured up to 300°C to give semi‐2‐IPNs. The MBMI/PEI semi‐IPN systems were characterized by UV‐Vis spectroscopy, FTIR spectroscopy and thermal techniques. The phase morphology, isothermal aging, and water uptake of semi‐IPN systems have also been studied. The morphological studies on phase distribution were investigated by scanning electron microscopy (SEM). Thermal performance of MBMI/PEI semi‐IPN systems were evaluated by DSC and thermo gravimetric analysis (TGA). All the compositions of semi‐IPN polyimide system were stable up to 400°C and their thermal stability increased with increase in the content of PEI. Isothermal aging studies done at 300°C for various time periods showed good thermo‐oxidative stability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

端羧基丁腈橡胶改性酚醛树脂的性能研究

采用端羧基丁腈橡胶（CTBN）对酚醛树脂进行改性,研究CTBN用量对改性酚醛树脂力学性能的影响。酚醛树脂的拉伸强度、断裂伸长率随CTBN用量的增大而呈上升趋势,当CTBN用量为10％时,拉伸强度、断裂伸长率达到最大值,并利用扫描电子显微镜（SEM）、傅立叶转换红外光谱（FTIR）和热重法（TGA）对改性前后酚醛树脂的结构和热性能进行分析。结果表明,CTBN与酚醛树脂之间发生了化学反应,并且改性酚醛树脂的热性能有所下降。