Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Effect of in situ polymerization conditions of methyl methacrylate on the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene) PMMA/AES Blends

In this study, the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene‐g‐styrene) (PMMA‐AES) blends were investigated with emphasis on the influence of the in situ polymerization conditions of methyl methacrylate. PMMA‐AES blends were obtained by in situ polymerization, varying the solvent (chloroform or toluene) and polymerization conditions: method A—no stirring and air atmosphere; method B—stirring and N₂ atmosphere. The blends were characterized by infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and dynamic mechanical analysis (DMA). The results showed that the PMMA‐AES blends are immiscible and present complex morphologies. This morphology shows an elastomeric dispersed phase in a glassy matrix, with inclusion of the matrix in the elastomer domains, suggesting core shell or salami morphology. The occlusion of the glassy phase within the elastomeric domains can be due to the formation of graft copolymer and/or phase inversion during polymerization. However, this morphology is affected by the polymerization conditions (stirring and air or N₂ atmosphere) and by the solvent used. The selective extraction of the blends' components and infrared spectroscopy showed that crosslinked and/or grafting reactions occur on the elastomer chains during MMA polymerization. The glass transition of the elastomer phase is influenced by morphology, crosslinking, and grafting degree and, therefore, T_g depends on the polymerization conditions. On the other hand, the behavior of T_g of the glassy phase with blend composition suggests miscibility or partial miscibility for the SAN phase of AES and PMMA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Adsorption of heavy‐metal ions on poly(ethylene imine)‐immobilized poly(methyl methacrylate) microspheres

Poly(methyl methacrylate) (PMMA) microspheres carrying poly(ethylene imine) (PEI) were prepared for the removal of heavy‐metal ions (copper, cadmium, and lead) from aqueous solutions with different amounts of these ions (50–600 mg/L) and different pH values (3.0–7.0). Ester groups in the PMMA structures were converted to imine groups in a reaction with PEI as a metal‐chelating ligand in the presence of NaH. The adsorption of heavy‐metal ions on the unmodified PMMA microspheres was very low [3.6 μmol/g for Cu(II), 4.6 μmol/g for Cd(II), and 4.2 μmol/g for Pb(II)]. PEI immobilization significantly increased the heavy‐metal adsorption [0.224 mmol/g for Cu(II), 0.276 mmol/g for Cd(II), and 0.126 mmol/g for Pb(II)]. The affinity order of adsorption (in moles) was Cd(II) > Cu(II) > Pb(II). The adsorption of heavy‐metal ions increased with increasing pH and reached a plateau value around pH 5.5. Their adsorption behavior was approximately described with the Langmuir equation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 197–205, 2001     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Methanol‐ and ethanol‐induced convex deformation and macrovoid formation of poly(methyl methacrylate)

Methanol‐ and ethanol‐induced convex deformation and macrovoid formation in poly(methyl methacrylate) (PMMA) through sandwich structures, consisting of polycarbonate (PC)/PMMA/PC was investigated. The sandwich structures had a circular hole on the outer PC layer, which allowed the solvent to contact with PMMA. Both single‐convex and double‐convex deformations of the PMMA layer were produced, depending upon the hole diameter. For a fixed hole diameter, there was an optimum PMMA thickness, which produced maximum curvature for the double‐convex deformation. The physical mechanism for these phenomena can be well explained by the relative strength of the swelling stress and the deformation resistance of the PMMA layer. We also used the wet phase‐inversion method to produce porous convex deformation for the sandwich structures. The size, number, and location of the convex pores can be prescribed. This may have potential applications in local filtering and other areas. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2254–2261, 2004     

An investigation into the degree and rate of polymerization of poly(methyl methacrylate) in the ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate

Room‐temperature ionic liquids (ILs), including 1‐butyl‐3‐methylimidazolium hexafluorophosphate, [bmim⁺][PF₆^?], were investigated as replacements for volatile organic compounds in the free‐radical solution polymerization of poly(methyl methacrylate) (PMMA). The latter was synthesized in benzene and [bmim⁺][PF₆^?] at 70 °C via a free‐radical process and the degree and rate of polymerization were compared based on the solvent used. The degree of polymerization was found to be five times higher in [bmim⁺][PF₆^?] than in benzene, while the rate of reaction was approximately four times faster in [bmim⁺][PF₆^?]. The results indicate the potential for using ILs to produce high‐molecular‐weight polymers and block structures based on the increased free‐radical stability in ILs. Copyright © 2004 Society of Chemical Industry     

Synthesis of amphiphilic poly(methyl methacrylate)‐block‐poly(methacrylic acid) diblock copolymers by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of 1‐(butoxy)ethyl methacrylate (BEMA) was carried out using CuBr/2,2′‐bipyridyl complex as catalyst and 2‐bromo‐2‐methyl‐propionic acid ester as initiator. The number average molecular weight of the obtained polymers increased with monomer conversion, and molecular weight distributions were unimodal throughout the reaction and shifted toward higher molecular weights. Using poly(methyl methacrylate) (PMMA) with a bromine atom at the chain end, which was prepared by ATRP, as the macro‐initiator, a diblock copolymer PMMA‐block‐poly [1‐(butoxy)ethyl methacrylate] (PMMA‐b‐PBEMA) has been synthesized by means of ATRP of BEMA. The amphiphilic diblock copolymer PMMA‐block‐poly(methacrylic acid) can be further obtained very easily by hydrolysis of PMMA‐b‐PBEMA under mild acidic conditions. The molecular weight and the structure of the above‐mentioned polymers were characterized with gel permeation chromatography, infrared spectroscopy and nuclear magnetic resonance. Copyright © 2005 Society of Chemical Industry     

Effect of Silica‐Coated Poly(butyl methacrylate)‐block‐poly(methyl methacrylate) Double‐Shell Particles on the Mechanical Properties of PMMA Composites

Silica nanoparticles with an average diameter of 12 nm are grafted with PBMA‐b‐PMMA double shells through typical sequential ATRP from bromoisobutyrate initiators anchored at the silica surface using an epoxysilane. A commercially available PMMA homopolymer is used for the preparation of composites with unmodified, silane‐modified and double‐shell‐modified silica particles. Good mechanical properties are obtained for silica double shell containing systems. The silica content in double shell particle systems is varied from 0 to 2.5 wt%. A significant improvement in impact properties is observed. The surface‐modified silica particles are characterized by ATR‐FTIR, NMR, GPC, and thermal analyses. TEM analysis is used to analyze the nature of dispersion of particles in the composites.

     

Facile fabrication of poly(methyl methacrylate) monolith via thermally induced phase separation by utilizing unique cosolvency

Poly(methyl methacrylate) (PMMA) monoliths with a three-dimensional continuous interconnected porous structure in a single piece were fabricated via thermally induced phase separation (TIPS) by utilizing unique cosolvency toward PMMA. We found that PMMA was soluble in a mixture of non-solvents (ethanol and water) at 60 °C. Cooling the solution resulted in formation of a monolith having interconnected pores. Cross-sectional analysis using scanning electron microscopy (SEM) showed a continuous porous network with submicron-sized skeleton. The pore size of the monolith was readily controlled by varying the fabrication parameters such as the polymer concentration and molecular weight, the cooling temperature and the solvent composition. The cross-section of the monolith showed high water repellency. The PMMA monolith was also obtained in a mixture of isopropanol and water with an appropriate solvent ratio.     

Poly(ethylene‐co‐vinyl acetate)‐graft‐poly(methyl methacrylate) (EVA‐graft‐PMMA) as a modifier of epoxy resins

Conventional approaches to toughen thermosets are: (1) the polymerization‐induced phase separation of a rubber or a thermoplastic, or (2) the use of a dispersion of preformed particles in the initial formulation. In the present study it is shown that it is possible to combine both techniques by using graft copolymers with one of the blocks being initially immiscible and the other that phase separates during polymerization. This is illustrated by the use of poly(ethylene‐co‐vinyl acetate)‐graft‐poly(methyl methacrylate) (EVA‐graft‐PMMA) as modifier of an epoxy resin. EVA is initially immiscible and PMMA phase separates during polymerization. Blends of an epoxy monomer based on diglycidylether of bisphenol A (DGEBA, 100 parts by weight), piperidine (5 parts by weight), and PMMA (5 parts by weight), showed the typical polymerization‐induced phase separation of PMMA‐rich domains before gelation of the epoxy network. Replacing PMMA by EVA‐graft‐PMMA (5 parts by weight), yielded stable dispersions of EVA blocks, favoured by the initial solubility of PMMA blocks. Phase separation of PMMA blocks in the course of polymerization led to a dispersion of in situ generated biphasic particles (plausibly composed of EVA cores surrounded by PMMA shells), with average diameters varying from 0.3 to 0.6 µm with the cure temperature. This procedure may be used to generate stable dispersions of biphasic particles for toughening purposes. © 2002 Society of Chemical Industry     

Photo‐induced controlled radical polymerization of methyl methacrylate mediated by photosensitive nitroxides

Photosensitive nitroxides bearing different chromophore groups (benzophenone, naphthalene and quinoline) were synthesized and characterized. The photochemical properties of the synthesized products were investigated by UV?visible and fluorescence measurements. The results indicated that an efficient energy transfer from the chromophore moiety to the nitroxide radical moiety could occur within the molecular distances. The photo‐induced nitroxide‐mediated polymerization of methyl methacrylate (MMA) was performed using the photosensitive nitroxide/2,2‐dimethoxy‐2‐phenyl acetophenone as a bimolecular mediated system. The controlled character of the polymerization was confirmed by the linear tendency of molecular weight evolution with narrow molecular weight distribution (1.3?1.4). The experimental conditions, such as type of chromophore, initiator concentration and molar ratio of initiator/nitroxide, are discussed for a better understanding of the mechanism of the controlled polymerization. Using the polymerization products as macroinitiator, the chain extension reaction of MMA turned out to be able to re‐initiate further polymerization of the monomer. © 2014 Society of Chemical Industry     

悬浮聚合法制取不同分子量级别的聚甲基丙烯酸甲酯

采用粉状MgCO3 作为分散剂 ,悬浮聚合制取了分子量从 2 4× 10 4 ～ 2 5 4× 10 4 的聚甲基丙烯酸甲酯。考察了温度、引发剂种类和浓度、分子量调节剂、转化率对聚合物分子量的影响规律 ,用粘度法测量了聚合物聚甲基丙烯酸甲酯 (PMMA)的分子量。结果表明 :温度的升高、引发剂浓度的增大、分子量调节剂的加入都会导致分子量的减小 ,随着转化率的提高 ,聚合物的分子量增大。在同等条件下 ,引发剂过氧化苯甲酰 (BPO)聚合所得的分子量较偶氮二异丁腈 (AIBN)高。通过实验 ,得到了满足作者需求的分子量 (96× 10 4 ～ 10 0× 10 4 )的聚合物的聚合条件为 :分散剂MgCO3 用量 1% ,单体∶水相 =1∶2 5 (质量比 ) ,引发剂BPO浓度 0 5 % ,反应温度 70℃ ,反应时间 3h。     

Modeling of the sheet‐molding process for poly(methyl methacrylate)

The sheet‐molding process for the production of poly(methyl methacrylate) (PMMA) involves an isothermal batch reactor followed by polymerization in a mold (the latter is referred to as a “sheet reactor”). The temperature at the outer walls of the mold varies with time. In addition, due to finite rates of heat transfer in the viscous reaction mass, spatial temperature gradients are present inside the mold. Further, the volume of the reaction mass also decreases with polymerization. These several physicochemical phenomena are incorporated into the model developed for this process. It was found that the monomer conversion attains high values of near‐unity in most of the inner region in the mold. This is because of the high temperatures there, since the heat generated due to the exothermicity of the polymerization cannot be removed fast enough. However, the temperature of the mold walls has to be increased in the later stages of polymerization so that the material near the outer edges can also attain high conversions of about 98%. This would give PMMA sheets having excellent mechanical strength. The effects of important operating (decision) variables were studied and it was observed that the heat‐transfer resistance in the mold influences the spatial distribution of the temperature, which, in turn, influences the various properties (e.g., monomer conversion, number‐average molecular weight, and polydispersity index) of the product significantly. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1951–1971, 2001     

Modification of pristine multiwalled carbon nanotube by grafting with poly(methyl methacrylate) using benzoyl peroxide initiator

Multiwalled carbon nanotube was successfully grafted with poly(methyl methacrylate) by free radical mechanism using benzoyl peroxide initiator. The reaction was carried out in situ, where the initiator and methyl methacrylate monomer generated the polymer‐free radical that was subsequently grafted to the surface of the pristine multiwalled carbon nanotube. The multiwalled carbon nanotube grafted poly(methyl methacrylate) (MWCNT‐g‐PMMA) were characterized using Fourier transform infrared, differential scanning calorimetry, thermogravimetric analysis, ¹³ C‐solid NMR spectroscopy, X‐ray photoelectron spectroscopy, and scan electron microscopy. From the result of the characterizations, the grafting of poly(methyl methacrylate) on to multiwalled carbon nanotube was confirmed, and a percentage grafting of 41.51% weight was achieved under optimized conditions with respect to the temperature and the amount of the initiator. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43270.     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Material encapsulation in poly(methyl methacrylate) shell: A review

Material encapsulation is a relatively new technique for coating a micro/nanosize particle or droplet with polymeric or inorganic shell. Encapsulation technology has many applications in various fields including drug delivery, cosmetic, agriculture, thermal energy storage, textile, and self-healing polymers. Poly(methyl methacrylate) (PMMA) is widely used as shell material in encapsulation due to its high chemical stability, biocompatibility, nontoxicity, and good mechanical properties. The main approach for micro/nanoencapsulation of materials using PMMA as shell comprises emulsion-based techniques such as emulsion polymerization and solvent evaporation from oil-in-water emulsion. In the present review, we first focus on the encapsulation techniques of liquid materials with PMMA shell by analyzing the effective processing parameters influencing the preparation of PMMA micro/nanocapsules. We then describe the morphology of PMMA capsules in emulsion systems according to thermodynamic relations. The techniques to investigation of mechanical properties of capsule shell and the release mechanisms of core material from PMMA capsules were also investigated. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48039.     

Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000