Radiation‐induced grafting of glycidyl methacrylate onto high‐density polyethylene (HDPE) and radiation lamination of HDPE

Radiation‐induced grafting of glycidyl meth‐acrylate (GMA) onto high‐density polyethylene (HDPE) and the radiation lamination of HDPE by bulk grafting of GMA were reported. The effects of irradiation dose, monomer concentration, and atmosphere on grafting were investigated. The extent of grafting initially increased with irradiation dose and then remained almost constant. The extent of grafting was higher in 2M GMA than in 1M GMA at the same irradiation dose. The extent of grafting in nitrogen was higher than that in air. The grafted samples were characterized with FTIR spectrometry and thermogravimetric (TG) analysis. A carbonyl group was found on grafted HDPE samples, and the carbonyl index increased with the extent of grafting. TG analyses proved the existence of grafted materials on HDPE and the grafted GMA thermally decomposes at a temperature lower than that of HDPE. Strong adhesion could be obtained with radiation lamination of HDPE by bulk grafting of GMA. Benzophenone facilitates the grafting in a proper concentration range. The adhesion mechanism of the laminated samples was the entanglement of the grafted chains. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 772–779, 2005     

Study of modified polypropylene nonwoven cloth. I. graft copolymerization of 4‐vinylpyridine onto polypropylene nonwoven cloth by preirradiation method

Polypropylene (PP) nonwoven cloth was grafted with 4‐vinylpyridine (4‐VP) by a preirradiation method. The effects of preirradiation conditions on the mechanical properties of preirradiated PP nonwoven cloth and the percentage of grafting (Pg) of 4‐VP onto the preirradiated PP nonwoven cloth were systematically investigated. The results indicated that the mechanical properties of preirradiated PP nonwoven cloth decreased with increasing irradiation dose and that the Pg was greatly affected by the concentration of monomer, irradiation dose, grafting reaction temperature, and the addition of inhibitor and inorganic acid in the grafting reaction system. The grafted nonwoven cloth samples were characterized using IR spectroscopy and SEM. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1861–1868, 2000     

Comparative study of the radiation‐induced grafting of styrene onto poly(tetrafluoroethylene‐co‐perfluoropropylvinyl ether) and polypropylene substrates. I: Kinetics and structural investigation

A comparative study has been made of the radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐perfluoropropyl vinyl ether) (PFA) and polypropylene (PP) substrates, using the simultaneous irradiation method. Effects of grafting conditions such as monomer concentrations, type of solvent, dose rate and irradiation dose on the grafting yield were investigated. Under the same grafting conditions it was found that a higher degree of grafting of styrene was obtained using a mixture of dichloromethane/methanol solvents for PFA and methanol for PP and the degree of grafting was higher in PP than in PFA at all doses. However, the micro‐Raman spectroscopy analysis of the graft revealed that, for the same degree of grafting, the penetration depth of the grafted polystyrene into the substrate was higher in PFA than in PP substrates. In both polymers the crystallinity was hardly affected by the grafting process and the degree of crystallinity decreased slightly with grafting dose. The dependence of the initial rate of grafting on the dose rate and the monomer concentration was found to be 0.6 and 1.4 order for PFA and 0.15 and 2.2 for PP, respectively. The degree of grafting increased with increasing radiation dose in both polymers. However, the grafting yield decreased with an increase in the dose rate. The increase in the overall grafting yield for PFA and PP was accompanied by a proportional increase in the penetration depth of the graft into the substrates. Copyright © 2003 Society of Chemical Industry     

The effect of grafted TMPM on the radiation resistance of polypropylene

The γ‐radiation–induced graft copolymerization of 2,2,6,6‐tetramethyl‐4‐piperidinyl methacrylate (TMPM) onto polypropylene (PP) was investigated using a simultaneous‐irradiation technique. The effects of solvents, atmospheres, dose, and monomer concentration on the percent of grafting were studied. The grafted TMPM showed better thermal stability, solvent extraction resistance, and compatibility with PP than monomeric TMPM or polymeric PTMPM. The stabilizing effectiveness of grafted TMPM on the radiation resistance of PP was found to be better than that of monomeric TMPM. The combination of grafted TMPM and low molecular weight hindered amine light stabilizers showed higher stabilizing effectiveness. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2150–2157, 1999     

Grafting of Hindered Amine Stabilizer in Poly(propylene) Films under γ‐Irradiation

Summary: In this paper, the grafting of a hindered amine stabilizer (HAS) is studied in isotactic poly(propylene) (PP) films under γ‐irradiation. The HAS used has a definite structure that combines a hindered amine functionality and a UV‐absorbing unit (benzylidene malonate ester group) detectable at 308 nm in the UV spectrum of PP film and 314 nm in chloroform. The stabilizer is added to the polymer at various concentration ratios: 0.1, 0.2, and 0.3 wt.‐%. The percentage of HAS grafting in the PP film at various additive concentrations is determined as a function of γ‐radiation dose in the range of 0–100 kGy by direct spectroscopic measurements through the absorption band of the stabilizer in the UV spectra of the PP film. The percentage of free HAS extracted with chloroform from the PP film versus the radiation dose is determined by UV spectroscopy for all the additive concentrations used. This study reveals that only 80% of the HAS is grafted on the 100 kGy irradiated PP matrix independent of the additive concentration used. However, the percentage of HAS grafted on PP films displays an exponential dependence on γ‐radiation dose. These results are consistent with the data obtained on the free HAS content. γ‐Irradiation grafting of HAS in the PP is accompanied by the oxidative degradation of the polymer substrate that is evaluated by increasing the carbonyl index and reducing significantly the oxidation induction time of the PP films.

The percentage of hindered amine stabilizer grafted to the PP film as a function of γ‐radiation dose.     

Fabrication of reverse‐osmosis membranes for the desalination of underground water via the γ‐radiation grafting of acrylic acid onto polyethylene films

Research has been devoted to the desalination of saline water to fresh water suitable for human demands because of the shortage of water in some countries. Therefore, in this study, reverse‐osmosis membranes were prepared via the γ‐radiation graft copolymerization of acrylic acid onto high‐density and low‐density polyethylene. The factors that could affect the grafting process, such as the solvent type, monomer and inhibitor concentration, and irradiation dose, were investigated to determine the optimum conditions for radiation grafting. The polyethylene grafted acrylic acid copolymers (PAAc‐g‐PE) graft copolymer was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and mechanical, rheological, and thermal property testing to illustrate the possibility of practical use in water desalination. The prepared grafted membranes showed significant results in the reverse‐osmosis desalination method with underground saline water. The factors affecting the desalination of water, such as the water flux, operation time, and grafting percentage, were studied. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45410.     

Proton exchange membranes prepared by simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films. I. Effect of grafting conditions

The simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films was studied at room temperature. The effects of grafting conditions (type of solvent, irradiation dose, dose rate, and monomer concentration) were investigated. The degree of grafting was found to be dependent on the investigated grafting conditions. The dependence of the initial rate of grafting on the dose rate and the monomer concentration was found to be of 0.5 and 1.3 orders, respectively. The results suggest that grafting proceeds by the so‐called front mechanism in which the grafting front starts at the surface of the film and moves internally toward the middle of the film by successive diffusion of styrene through the grafted layers. Some selected properties of the grafted films were evaluated in correlation with the degree of grafting. We found that the grafted FEP films possess good mechanical stability, which encourages their use for the preparation of proton exchange membranes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 220–227, 2000     

Influence of grafting formulations and extrusion conditions on properties of silane‐grafted polypropylenes

The melt grafting of unsaturated silanes onto powdered polypropylene (PP) in a Haake TW100 twin‐screw extruder and curing in hot water were studied. The influence of grafting formulations and extrusion conditions on the melt flow rates of grafted PP and the gel percentages of crosslinked PP was investigated. The gel percentages of methacryloylpropyltrimethoxysilane (VMMS)‐grafted PP were markedly higher than those of vinyltriethoxysilane (VTES)‐ and vinyltrimethoxysilane (VTMS)‐grafted PP, while significantly less degradation of PP during grafting was observed for VMMS‐grafted PP. When benzoyl peroxide (BPO) was used as an initiator, no degradation of PP during grafting was observed, and the melt flow rates of grafted PP decreased with increasing BPO concentration. In contrast, use of dicumyl peroxide (DCP) as an initiator resulted in severe degradation of PP, and the melt flow rates of grafted PP increased gradually with increasing DCP concentration. BPO resulted in higher gel percentages than those of DCP at a fixed initiator concentration. Introduction of styrene into the grafting system greatly improved the gel percentage of crosslinked PP and reduced the degradation of PP during grafting. The optimum molar ratio of styrene to monomer is at about 1.5:1. Relatively low processing temperatures and high screw speeds are favorable. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1233–1238, 2000     

γ‐Radiation‐Induced Graft Copolymerization of Ethyl Acrylate onto Hydroxypropyl Methylcellulose

Summary: Graft copolymerization of EA onto water‐soluble HPMC was carried out using γ‐radiation using both simultaneous and preirradiation in an aqueous medium. The effects of radiation environment, radiation dose, monomer concentration, and reaction temperature on percentage of grafting (G) and grafting efficiency (G_E) were investigated. For preirradiation, the observed values for G and G_E were higher in air than in a nitrogen atmosphere. G and G_E values are obviously higher for preirradiation; their maximum values were obtained for a radiation dose of 1.8 kGy. The grafting parameters increase for increasing monomer concentration up to 0.15 mol · L^?1, where they reach their saturation values. In the case of preirradiation, the largest grafting parameters are obtained at 65 °C. The graft copolymers obtained were characterized by FTIR spectroscopy, TEM, SEM, and XRD methods. The method of irradiation significantly affects the mechanical properties of the grafted HPMC samples. Samples prepared by simultaneous irradiation show superior mechanical properties. In addition, the equilibrium humidity adsorption behaviors of the grafted copolymers were also studied, and the humidity resistance behavior of HPMC was enhanced through the grafting copolymerization.

Transmission electron micrograph of the HPMC‐g‐PEA water dispersion.     

Electron‐beam‐radiation‐induced grafting of acrylonitrile onto polypropylene fibers: Influence of the synthesis conditions

Electron‐beam‐radiation‐induced grafting of acrylonitrile onto polypropylene fibers was investigated with a pre‐irradiation method. Grafting conditions such as the solvents, additives, monomer concentration, radiation dose, and temperature were varied, and the effects on the degree of grafting were studied. The nature of the reaction medium and additives had a considerable influence on the degree of grafting. The dilution of acrylonitrile with N,N‐dimethylformamide significantly enhanced the degree of grafting in comparison with other solvents. The addition of sulfuric acid to the reaction mixture led to an increase in the degree of grafting and an acceleration of the rate of grafting. The order of dependence of the rate of grafting on the pre‐irradiation dose and monomer concentration was found to be 1.31 and 1.21, respectively, in the presence of sulfuric acid. The activation energy for grafting was calculated to be 21.9 kJ/mol. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Radiation‐induced graft copolymerization of methylmethacrylate onto poly(tetrafluoroethylene‐co‐ethylene) film

Modification of poly(tetrafluoroethylene‐co‐ethylene), Tefzel (ETFE), film has been carried out by grafting methylmethacrylate (MMA) by radiation method including preirradiation and double‐irradiation methods. Percentage of grafting has been determined as a function of the (i) total dose, (ii) monomer concentration, (iii) amount of liquor ratio, (iv) reaction time, and (v) temperature.The effect of different alcohols such as methanol, ethanol, 2‐propanol, n‐butanol, n‐pentanol, and 2‐ethoxy ethanol on percentage of grafting of MMA was also studied. The graft copolymers were characterized by IR spectroscopy and thermogravimetric analysis (TGA). Methylmethacrylate produces higher percentage of grafting by preirradiaton method than double‐irradiation method. MMA‐grafted ETFE films (S_irr), i.e., prepared by preirradiation involving single irradiation show better thermal stability than MMA‐grafted ETFE films (D_irr), i.e., prepared by double irradiation and unmodified ETFE film. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Swelling behavior and cell viability of dehydrothermally crosslinked poly(vinyl alcohol) hydrogel grafted with N‐vinyl pyrrolidone or acrylic acid using γ‐radiation

To improve equilibrium water content, dehydrothermally crosslinked poly(vinyl alcohol) (PVA) hydrogel was grafted with N‐vinyl pyrrolidone (NVP) or acrylic acid (AA) monomer using γ‐radiation. Swelling behavior of the grafted hydrogels was studied in phosphate‐buffered saline, and cell viability was evaluated using fibroblast cells from mouse connective tissue. Equilibrium water content of AA‐ and NVP‐grafted PVA hydrogel ranged between 40–60% and 60–80%, respectively, depending on radiation dose and monomer concentration. For maximum degree of swelling, the optimum monomer concentration and radiation dose were 20% by weight and 20 kGy, respectively. Fibroblast cells seeded on NVP‐grafted hydrogel had an extended oval morphology while those seeded on AA‐grafted PVA had a rounded spherical morphology. These results support the use of NVP for grafting PVA to increase swelling and improve cell viability. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2862–2868, 2004     

Temperature Sensitive Behavior of Poly(N‐isopropylacrylamide) Grafted Onto Electron Beam‐Irradiated Poly(propylene)

Summary: N‐Isopropylacrylamide (NIPAAm) was graft‐polymerized from its acetone solution onto poly(propylene) (PP) films, after electron‐beam irradiation in the presence of air oxygen. The effects of pre‐irradiation dose as well as monomer concentration, reaction temperature and reaction time on the grafting efficiency were investigated. Typical conditions for achieving maximum grafting yield were observed for 1 M monomer concentration, after PP pre‐irradiation with a 300 kGy dose and a reaction temperature of 50 °C. The location of the graft polymerization was examined by different methods including measurements of dimensional variations, calorimetry, SEM and AFM. The temperature‐responsive behavior of grafted copolymer was studied by swelling and contact angle measurements at different temperatures.

Temperature dependence of the swelling ratio in water as a function of temperature.     

Synthesis and characterization of polyethylene modified through phase‐transfer‐catalyzed graft copolymerization

In an effort to impart biodegradability, polyethylene (PE) was modified through the graft copolymerization of vinyl monomers such as acrylamide (AAm) and acrylic acid (AAc) by a phase‐transfer‐catalyst method. The grafting percentage of AAm and AAc for PE was found to be dependent on the dibenzoyl peroxide concentration, monomer concentration, time, temperature, and concentration of the phase‐transfer catalyst. Some AAm‐ and AAc‐grafted PE samples were prepared by chemical, UV, and γ‐radiation methods. The biodegradation of samples of PE, polyethylene‐g‐polyacrylamide, and polyethylene‐g‐poly(acrylic acid) prepared by all these methods was studied. The weight loss of the samples over a period of time was observed with soil‐burial tests. The grafted samples prepared by the phase‐transfer‐catalyst method showed better biodegradation results than those prepared by other methods of grafting. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Functionalization of Poly(propylene) Fabric with 4‐Vinylpyridine,N,N‐Dimethylacrylamide and Styrene by γ‐Radiation‐Induced Grafting in an Aqueous Environment

Summary: VP and co‐monomers DMAAm and ST were successfully grafted onto a PP fabric in an emulsion copolymerization process initiated by γ‐radiation. The radiation dose, concentration of VP, the ratio of VP/DMAAm and VP/ST in the reaction solution, and the reaction temperature dependent graft copolymerization were investigated. The order of dependence of the initial rate of grafting on the radiation dose was found to be in the range of 1.2 to 0.93 for VP; 0.84 to 0.70 for VP/DMAAm and for VP/ST was in the range of 0.59 to 0.41. The activation energy of the graft copolymer reaction was determined to be 40.18 J · mol^?1 for 0.464 mol · L^?1 VP. In the case of co‐monomer mixtures (VP/DMAAm: 0.464/0.5) the energy of activation was noticeably higher at 49.71 J · mol^?1 while for VP/ST (0.464/0.436) the activation energy was same as that of VP. XRD results showed that overall crystallinity significantly decreased with the increase of graft weight with a noticeable change in the chemical structure of the PP, indicating that the graft copolymer reaction was taking place both in the amorphous and crystalline regions of PP. A similar characteristic behavior was also obtained by DSC, which revealed the presence of an endotherm process in the range of 25 to 130 °C depending on the degree of grafting, attributed to the grafted chains of the monomer/co‐monomers. In order to determine the graft copolymer reaction of VP, DMAAm and ST onto the backbone of PP, the reaction products were characterized by FTIR spectroscopy. A good correlation was found between changes of crystallinity and level of graft copolymerization as determined by WAXRD and DSC.

Typical XRD traces of as‐received PP fabric (PPF) and grafted with VP (PPF‐g‐VP).     

Gamma radiation‐induced graft copolymerization of styrene onto poly(ethyleneterephthalate) films

Gamma radiation‐induced graft copolymerization of styrene onto poly(ethylene terephthalate) (PET) films was studied using simultaneous irradiation technique. The effects of grafting conditions on the degree of grafting were investigated. The grafting conditions include monomer concentration, irradiation dose, dose rate, and the type of solvent. Moreover, the effect of the addition of crosslinking agents [i.e., divinylbenzene (DVB) and triallyl cyanurate (TAC)] having various concentrations were also investigated. The degree of grafting was found to be greatly dependent on the grafting conditions. Of the three diluents employed, methylene chloride was found to drastically enhance the degree of grafting. The order of dependence of the initial rate of grafting on the monomer concentration was found to be 2.2. The grafted PET films were identified by FTIR spectroscopy and characterized by X‐ray diffraction (XRD). © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1003–1012, 2000     

Radiation‐induced grafting of styrene onto poly(tetrafluoroethylene) (PTFE) films. I. Effect of grafting conditions and properties of the grafted films

Radiation‐induced grafting of styrene onto poly(tetrafluoroethylene) (PTFE) films was studied by a simultaneous irradiation technique. Grafting was carried out using γ‐radiation from a ⁶⁰Co source at dose rates of 1.32–15.0 kGy h⁻¹ at room temperature. The effects of type of diluent, dose rate, irradiation dose, and the initial monomer concentration in the grafting solution on the degree of grafting were investigated. The degree of grafting was found to be strongly dependent upon the grafting conditions. The dependence of the initial rate of grafting on the dose rate and the initial monomer concentration in the grafting solution was found to be in the order of 0.6 and 1.7, respectively. The chemical structure and the crystallinity of the grafted PTFE films were studied by means of Fourier‐transform infrared, (FTIR), electron spectroscopy for chemical analysis (ESCA) and X‐ray diffractometry (XRD). © 2000 Society of Chemical Industry     

Surface modification of polypropylene sheets by UV‐radiation grafting polymerization

1,6‐Hexanediol diacrylate (HDDA) was grafted onto polypropylene (PP) substrates in the presence of benzophenone (BP) and isopropylthioxanthone (ITX) photoinitiators, and then polyurethane acrylate formulations were coated onto the HDDA‐g‐PP substrates, using UV radiation. The amount grafted and the grafting efficiency of the polymerizations were determined gravimetrically. The effects of the photoinitiator concentration and the UV radiation intensity on the physicochemical surface properties and the grafting efficiency of the UV‐radiation grafting polymerizations were characterized in detail using contact‐angle measurements, Fourier transform infrared spectroscopy with attenuated total internal reflection, and scanning electron microscopy. The results showed that the amount grafted and the surface polarity of the HDDA‐g‐PP substrates both increased linearly with increasing BP photoinitiator concentration and UV radiation intensity, and that the addition of a small amount of ITX markedly enhanced both parameters, probably due to photosensitization. The adhesion of the UV‐cured coating onto the HDDA‐g‐PP substrates was evaluated using the crosshatch adhesion test. The results indicated that the amount of HDDA grafted onto the PP substrates should exceed about 1 mmol/cm² for satisfactory adhesion with the UV‐cured coating. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1446–1461, 2006     

Styrene‐assisted free‐radical graft copolymerization of maleic anhydride onto polypropylene in supercritical carbon dioxide

The free‐radical graft copolymerization of maleic anhydride (MAH) onto polypropylene (PP) with the assistance of styrene (St) in supercritical carbon dioxide (CO₂) was studied. The effects of the St concentration and initiator concentration on the functionality degree of the grafted PP in supercritical CO₂ were investigated. The addition of St drastically increased the MAH functionality degree, which reached a maximum when the molar ratio of MAH and St was 1:1. St, an electron‐donating monomer, could interact with MAH through charge‐transfer complexes to form the St–MAH copolymer (SMA), which could then react with PP macroradicals to produce branches by termination between radicals. There was SMA in the grafting reaction system characterized by Fourier transform infrared and differential scanning calorimetry. Furthermore, the highest MAH functionality degree was obtained when the concentration of 2,2′‐azobisisobutyronitrile (AIBN) was 0.6 wt % based on PP. The effects of the temperature and pressure of supercritical CO₂ on the functionality degree of the grafted PP were analyzed. An increase in the temperature accelerated the decomposition rate constant of AIBN, thereby promoting the grafting reaction. In addition, an increase in the temperature increased the diffusion of monomers and radicals in the disperse reaction system of supercritical CO₂. The highest degree of functionality was found at 80°C. Also, the functionality degree of grafted PP decreased with an increase in the pressure of supercritical CO₂ within the experimental range. The morphologies of pure PP and grafted PP were significantly different under polarizing optical microscopy. The PP spherulites were about 38 μm in size, and the grafted PP spherulites were significantly reduced because of heterogeneous nucleation. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 853–860, 2003     

Study of multi‐monomer melt‐grafting onto polypropylene in an extruder

Free‐radical melt‐grafting of the dual‐monomer systems glycidyl methacrylate–styrene (GMA‐St) and hydroxyethyl methacrylate–styrene (HEMA‐St) onto polypropylene (PP) has been studied using a single‐screw extruder. For single monomer grafting systems, degradation of PP was unavoidable and deterioration of the mechanical properties of the grafted PP subsequently occurred because of β‐scission of PP chains during the free‐radical melt‐grafting process. However, for the dual‐monomer systems, it is shown that the addition of styrene as a comonomer can significantly enhance the GMA or HEMA grafting levels on PP and reduce the extent of β‐scission of PP backbone. It has been found that the grafting degree of dual‐monomer melt‐grafted PP, such as PP‐g‐(GMA‐co‐St) or PP‐g‐(HEMA‐co‐St), is about quadruple that of single‐monomer grafted PP for the same monomer and dicumyl peroxide concentrations. Moreover, the melt flow rate of the dual‐monomer grafted PP is smaller than that of the unmodified PP. Hence, PP not only was endowed with higher polarity, but also kept its good mechanical properties. © 2000 Society of Chemical Industry