Effect of organosilane coupling agents on microstructure and properties of nanosilica/epoxy composites

Three types of silane coupling agents, γ‐aminopropyltriethoxysilane, γ‐glycidoxypropyltrimethoxysilane, and γ‐methacryloxypropyltrimethoxysilane, were used as modifiers to modify the surface of the nanosilica, respectively, and the nanocomposites of the epoxy resin filled with nano‐sized silica modified by three silane coupling agents were prepared by physical blending. The properties of the modified silica nanoparticles were characterized by Fourier transform infrared spectrum and particle‐size analyzer. The microstructure, mechanical behavior, and heat resistant properties of the nanocomposites were investigated by transmission electron microscopy, scanning electron microscopy, thermo gravimetric analyses, differential thermal gravity, differential scanning calorimetry, and flexural tests. The results showed that these modifiers are combined to the surfaces of nanosilica by the covalent bonds, and they change the surface properties of nanosilica. The different structures of coupling agents have different effects on the dispersibility and stability of modified particles in the epoxy matrix. In comparison, the silica nanoparticles modified by γ‐glycidoxypropyltrimethoxysilane exhibit a good dispersivity. The nanocomposites with 4 wt% weight fraction nanosilica modified by γ‐glycidoxypropyltrimethoxysilane have higher thermal decomposing temperature and glass transition temperature than those of the other two composites with the same nanosilica contents, and they are raised by 43.8 and 8°C relative to the unmodified composites, respectively. The modified silica nanoparticles have good reinforcing and toughening effect on the epoxy matrix. The ultimate flexural strengths of the composites with 4 wt% nanoparticles modified by γ‐aminopropyltriethoxysilane, γ‐glycidoxypropyltrimethoxysilane, and γ‐methacryloxypropyltrimethoxysilane are increased by 10, 30, and 8% relative to the unmodified composites, respectively. The flexural fracture surfaces of modified composites present ductile fracture features. POLYM. COMPOS. 2012. © 2012 Society of Plastics Engineers     

The effect of nanosilica on mechanical,thermal and morphological properties of epoxy coating

In this study, nanosilica of very high specific surface area is used as reinforcing filler for preparing an epoxy-based nanocomposite coating. For appropriate dispersion of nanoparticles in the polymer matrix, ultrasound waves were applied after mechanical mixing. The resulting perfect dispersion of nanosilica particles in epoxy coating revealed by transmission electron microscopy ensured the transparency of the nanocomposite. Nanoindentation was used to determine some mechanical properties such as hardness and elastic modulus. The obtained results show 26 and 21% increases in hardness and elastic modulus, respectively for resin filled with 5% nanosilica compared to neat epoxy. DMA results show that the glass transition temperature of samples is increased with increasing silica nanoparticles. The result of TGA shows significant improvement of the thermal decomposition temperature of epoxy coating containing 5% nanosilica compared to neat epoxy. Scanning electron microscopy (SEM) micrographs of fractured surfaces show increased roughness with nanosilica addition.     

Studying the mechanical properties of composites made of Kenaf‐Nylon 66 fabric,silica nanoparticles,and epoxy resin

In this study, the effect of the relationship between yarn material and yarn count tex on the mechanical behavior of plainly woven hybrid fabrics impregnated with silica nanoparticles and epoxy resin has been investigated. First, various types of bicomponent and single‐component fabrics with plain weaves are prepared using kenaf and nylon‐66 yarns with yarn tex count of 334 and 427. To prepare the composite, silica nanoparticles with a particle size of 200 nm are mechanically mixed into glycol polyethylene with a molecular weight of 200 along with ethanol in proportions of 6:1. The weight percent of silica particles in the suspension has been selected as 60%. Using a round edge indenter, the concentrated indentation force test has been performed based on the 6264D standard to determine the strength of each fabric sample. Then, by impregnating the mentioned fabrics with polymer materials (silica nanoparticles and epoxy resin) and performing the concentrated force tests again, it is found that the hybrid fabrics with a yarn tex count of 427 and impregnated with polymer material enjoy the highest shear thickening properties. POLYM. COMPOS., 37:674–683, 2016. © 2014 Society of Plastics Engineers     

Novel polymer composites based on a mixture of preformed nanosilica‐filled poly(methyl methacrylate) particles and a diepoxy/diamine thermoset system

In this work, a new material based on an epoxy thermoset modified with a thermoplastic filled with silica nanoparticles was investigated. When thermoplastic particles are filled with nanoparticles with unique properties such as high efficiency for absorbing ultraviolet light, electric or magnetic shielding, high electrical conductivity, and high dielectric constants, more than an enhancement of the mechanical properties is expected to be achieved for modified epoxy‐based thermosets. Particles of poly(methyl methacrylate) (PMMA) filled with silica nanoparticles were used to modify a thermoset based on a full reaction between diglycidyl ether of bisphenol A and 3‐(aminomethyl)benzylamine. When the preformed thermoplastic particles were mixed with the reactive constituents of the epoxy system under certain curing conditions in which total miscibility was avoided, uniform particle dispersions could be obtained. The relationships between the composition, morphology (nanoscale and microscale), glass‐transition temperature, mechanical properties, and fracture toughness were considered. Four main results were obtained for consideration of the potential of silica‐filled PMMA as an important modifier of brittle epoxy thermoset systems: (1) a good dispersion of the silica nanoparticles in the PMMA domains, (2) a good dispersion of the silica‐filled PMMA microparticles in the epoxy matrix, (3) the possibility of partial dissolution of the PMMA‐rich domains into the epoxy system, and (4) a slight increase in properties such as the hardness, indentation modulus, and fracture toughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Interfacial interactions in silica‐reinforced polypropylene nanocomposites and their impact on the mechanical properties

The main focus of this study is to characterize the interfacial interactions between silica nanoparticles and polypropylene and to investigate how the surface properties and morphology of the silica nanoparticles affect the elastic response of the silica–polypropylene composites. The composites were prepared by melt compounding and injection molding. Both non‐functionalized and dimethyldichlorosilane‐functionalized silica nanoparticles were used. Three‐component composites were also prepared by including selected formulations of both poly(propylene‐g‐maleic anhydride) copolymer (PPgMA) and different types of silica. It was found that both silica types are nucleating agents for PP and significantly alter its crystallization behavior. A strong correlation between the glass transition temperature (T_g) and the tensile modulus in silica‐PP nanocomposites indicated the presence of a secondary reinforcing mechanism that is the pinning of the polymer chains on the silica surface. The presence of a complex constrained phase, represented by immobilized amorphous and transcrystalline phases, forming at the filler surface, was assessed by modulated differential scanning calorimetry and dynamic mechanical analysis. Finally, the interfacial interactions were correlated to the tensile and viscoelastic properties using the theoretical models proposed by Pukanszky and Sumita et al., respectively, and comparing the predictions of the models to experimental results. POLYM. COMPOS., 37:2018–2026, 2016. © 2015 Society of Plastics Engineers     

Preparation and physical properties of transparent organic–inorganic nanohybrid materials based on urethane dimethacrylate

The aim of this study was to prepare transparent organic–inorganic nanohybrid materials with improved physical properties in comparison with the matrix polymer. Polymerizable silica nanoparticles were synthesized via the reaction of silanol groups on the surface of silica nanoparticles (particle diameter ≈ 12 nm) with isocyanate groups of 2‐(methacryloyloxy)ethyl isocyanate (MOI) in ethyl acetate. In addition, the matrix monomer, urethane dimethacrylate, was prepared by the reaction of an MOI isocyanate group with the hydroxyl group of 2‐hydroxyethyl methacrylate, and novel organic–inorganic nanohybrid materials were obtained at various silica contents with bulk polymerization. The surface treatment of the silica nanoparticles and preparation of the matrix monomer were carried out in a one‐pot reaction. The prepared hybrid materials retained high transparency, and the elastic modulus and surface hardness improved with increasing silica content. Moreover, the strength of the material containing 20 wt % silica was up to 30 MPa higher than that of the matrix polymer. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Facile fabrication and modification of polyacrylate/silica nanocomposite latexes prepared by silica sol and silane coupling agent

Polyacrylate/silica nanocomposite latexes were prepared by silica sol and facilely modified with a silane coupling agent γ-methacryloxypropyltrimethoxysilane (KH-570) aimed at reinforcing the interaction between silica nanoparticles and latex particles in a convenient way. The effects of silica sol and KH-570 amounts on the performance of latexes and films are discussed. Particle size and morphology tests demonstrated that the silica nanoparticles could form hydrogen bond interactions between latex particles, and thus influence the rheological properties of latexes. Tensile measurements and SEM photographs showed the reinforcing and toughening roles of silica nanoparticles. SEM images also indicated that the addition of silica sol increased the roughness of films, which resulted in the increase of hydrophilic silanol groups on the film surface and the decrease of water resistance of latex films. The latex films retained good adhesion force, flexibility, and impact resistance even when the silica sol content was as much as 25%. TGA data revealed that the incorporation of silica sol enhanced the thermal stability of the films. After introducing KH-570, the particle size increased with the increase of the amount of KH-570. Moreover, the addition of KH-570 improved the water resistance and maintained other properties of the latex films appropriately.     

Preparation and properties of urethane acrylate-epoxy interpenetrating polymer networks containing silica nanoparticles

Summary In this study, interpenetrating polymer networks (IPNs) and IPN composite materials were prepared by in situ polymerization of urethane dimethacrylate (UDMA) and bisphenol-A diglycidyl ether epoxy resin (DGEBA) with or without silica nanoparticles. Dynamic mechanical analysis (DMA), three-point bending test, thermogravimetric analysis (TGA) and visible spectrometry were performed to evaluate the physical properties of the resulting IPNs and IPN composite materials. The IPNs showed high transparency and higher elastic modulus and strength than that of each homopolymer at ratio of UDMA/ DGEBA is 70/30. The IPN composites maintained high transparency in spite of the addition of silica nanoparticles. Moreover, elastic modulus and surface hardness of the IPN composites increased with increasing silica content.     

Production of filled hydrogels by mechanochemically induced polymerization

Silica nanoparticles functionalized with polyvinylpyrrolidone (PVP) were obtained by the grinding/mechanical activation of quartz or nonfunctionalized silica nanoparticles in a stirred media mill in the presence of 1‐vinyl‐2‐pyrrolidone, as proven by Fourier transform infrared spectroscopy. The polymer layer thickness formed on the silica nanoparticles after 8 h of mechanical activation in the absence of polymerization initiators amounted to about 10 nm, as derived from shear rheology. The silica nanoparticles functionalized with the hydrophilic PVP by mechanochemical polymerization reaction were used as fillers for hydrogels based on poly(hydroxyethyl methacrylate) (polyHEMA). The water absorption, release properties, and mechanical properties of the polyHEMA–silica composites were measured as functions of the filler content and particle size of the filler. PolyHEMA samples containing 20 wt % of the functionalized silica particles exhibited a higher maximum water absorption than the unfilled polymer; this showed that the hydrophilic interface between the filler and the matrix improved the water absorption. The release of methylene blue from the polyHEMA–silica composites was governed by diffusion and was almost unaffected by the silica particles. The values for the storage modulus and loss modulus of the polyHEMA–silica composites increased with growing filler content. For constant filler content, the storage modulus increased with decreasing particle diameter of the filler; this showed that the reinforcing effect increased with the interface between the filler particles and the matrix polymer. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Study of the effect of the concentration,size and surface chemistry of zirconia and silica nanoparticle fillers within an epoxy resin on the bulk properties of the resulting nanocomposites

Epoxy resin nanocomposites were prepared by curing bisphenol‐F with an aliphatic amine in the presence of SiO₂ and ZrO₂ nanoparticles as inorganic fillers. Both types of particles were prepared with diameters of around 10 nm and 70 nm to study size effects in the nanocomposites. The nanoparticles showed a different constitution: while silica was amorphous and spherical in nature, zirconia was crystalline and non‐spherical. Both nanoparticles were surface‐functionalized with novel diethylene‐glycol‐based capping agents to increase the compatibility with the epoxy matrix. The organic functionalities were attached to the nanoparticle surface via phosphonic acid (zirconia) and trialkoxysilane (silica) anchor groups. The homogeneity of the distribution of surface‐modified inorganic nano‐sized fillers in the matrix up to 5.8 vol% in case of silica and 2.34 vol% in case of zirconia was determined by small‐angle X‐ray scattering and transmission electron microscopy. Mechanical properties such as hardness and storage modulus were increased with increasing filler content while thermal stability of the obtained materials was nearly unaffected after incorporation of nanoparticles. Copyright © 2011 Society of Chemical Industry     

Thermally and mechanically enhanced epoxy resin‐silica hybrid materials containing primary amine‐modified silica nanoparticles

In this article, a series of hybrid materials consisted of epoxy resin matrix and well‐dispersed amino‐modified silica (denoted by AMS) nanoparticles were successfully prepared. First of all, the AMS nanoparticles were synthesized by performing the conventional acid‐catalyzed sol–gel reactions of tetraethyl orthosilicate (TEOS), which acts as acceded sol–gel precursor in the presence of 3‐aminopropyl trimethoxysilane (APTES), a silane coupling agent molecules. The as‐prepared AMS nanoparticles were then characterized by FTIR, ¹³C‐NMR, and ²⁹Si‐NMR spectroscopy. Subsequently, a series of hybrid materials were prepared by performing in situ thermal ring‐opening polymerization reactions of epoxy resin in the presence of as‐prepared AMS nanoparticles and raw silica (RS) particles (i.e., pristine silica). AMS nanoparticles were found to show better dispersion capability in the polymer matrices than that of RS particles based on the morphological observation of transmission electron microscopy (TEM) study. The better dispersion capability of AMS nanoparticles in hybrid materials was found to lead enhanced thermal, mechanical properties, reduced moisture absorption, and gas permeability based on the measurements of thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and gas permeability analysis (GPA), respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and thermo‐mechanical properties of heat‐resistant epoxy/silica hybrid materials

Diglycidyl ether of bisphenol‐A (DGEBA) based epoxy/silica hybrid materials filled with various amounts of 3‐glycidoxypropyltrimethoxysilane (GPTMS) and silica nanoparticles were prepared, using 4,4′‐diaminodiphenyl sulfone (DDS) as curing agent. The obtained hybrid materials were analyzed by means of Fourier‐transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The results indicated that the introduction of GPTMS and silica nanoparticles had synergistic effect. The addition of GPTMS not only ameliorated the compatibility between silica and the epoxy matrix but also increased the crosslinking density of the epoxy system; meanwhile the nano‐silica further reinforced the inorganic network of the hybrid system. Consequently, the hybrid materials showed much improved heat‐resistant properties. The storage modulus of the hybrid systems showed no obvious decrement in the glass transition region and kept at a high value even in the temperature region up to 300°C. The integral thermal stability of the resulting hybrid materials was also improved compared with the corresponding pure epoxy resin. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers.     

Rice husk‐derived porous carbon/silica particles as green filler for electronic package application

Bio‐based porous carbon/silica particles (denoted as RH‐carbon/silica) were successfully prepared from agricultural waste rice husk by using acid‐hydrothermal treatment and pyrolysis under nitrogen condition. As green filler, the cure behavior, thermal‐mechanical properties, and thermal conductivity of the epoxy‐carbon/silica biocomposites at different filler contents (5, 9, 17, 29 wt %) were characterized. Because of superior surface properties (surface area, porosity, and silica segment) and high content of carbon component in the RH‐carbon/silica, the characteristics of the biocomposites were significantly improved with the increase of the filler content. At 29 wt % of filler content, the epoxy biocomposites exhibit lower curing temperature (148 °C), lower CTE (42 ppm/°C), higher T_g (123 °C), higher storage modulus (4059 MPa), and higher effective thermal conductivity (0.29 W/mK). In brief, the RH‐carbon/silica particles that can serve not only as reinforcing agent but also as thermal transport medium used in epoxy composite, is a green and high‐performance filler for this purpose. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44699.     

Tribological and electrical properties of silica‐filled epoxy nanocomposites

The tribological and electrical properties of epoxy composites filled with nano‐sized silica particles are studied and discussed in this article. To enhance the interfacial interaction between the fillers and the matrix, nanoparticles were pretreated with silane coupling agent. Dry sliding wear tests were carried out with configuration of composite sample on a rotating steel disc. Electrical measurements such as AC breakdown voltage, at 50 Hz, high voltage‐low current arc resistance and wet tracking resistance were carried out. The results reveal the influence of nanosized silica loading on wear resistance of the epoxy. It is observed that 10 wt% loading of silica is very effective in reducing the wear loss. With further increase of silica filler loading, the nanoparticles agglomerated and resulted in increase of the specific wear rate. The influence of silica particles on the specific wear rate is more pronounced under sliding wear situation. The influence of silica particle loading on epoxy is evident in the results of electrical parameters like dielectric strength, arc resistance and tracking resistance. These parameters showed improvement with filler loading up to 15 wt% and beyond this value of filler loading noticeable deterioration was observed. The effects of electrical stresses in the morphologies of the surfaces of epoxy nanocomposites are discussed. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Polyurethaneurea–silica nanocomposites: Preparation and investigation of the structure–property behavior

Nanocomposites consisting of thermoplastic polyurethane–urea (TPU) and silica nanoparticles of various size and filler loadings were prepared by solution blending and extensively characterized by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), thermal analysis, tensile tests, and nanoindentation. TPU copolymer was based on a cycloaliphatic diisocyanate and poly(tetramethylene oxide) (PTMO-2000) soft segments and had urea hard segment content of 20% by weight. TPU/silica nanocomposites using silica particles of different size (29, 74 and 215 nm) and at different loadings (1, 5, 10, 20 and 40 wt. %) were prepared and characterized. Solution blending using isopropyl alcohol resulted in even distribution of silica nanoparticles in the polyurethane–urea matrix. FTIR spectroscopy indicated strong interactions between silica particles and polyether segments. Incorporation of silica nanoparticles of smaller size led to higher modulus and tensile strength of the nanocomposites, and elastomeric properties were retained. Increased filler content of up to about 20 wt. % resulted in materials with higher elastic moduli and tensile strength while the glass transition temperature remained the same. The fracture toughness increased relative to neat TPU regardless of the silica particle size. Improvements in tensile properties of the nanocomposites, particularly at intermediate silica loading levels and smaller particle size, are attributed to the interactions between the surface of silica nanoparticles and ether linkages of the polyether segments of the copolymers.     

Morphology and thermo‐mechanical properties of compatibilized polyimide‐silica nanocomposites

Polyimide‐silica nanocomposites have been prepared from an aromatic polyamic acid derived from pyromellitic dianhydride and oxydianiline and a silica network using the sol‐gel reaction. Compatibilization of the two components was achieved by modifying the silica network with imide linkages. Morphology, thermal, and mechanical properties of these composite materials were studied as a function of silica content and compared with the one in which reinforcement of the polyimide was achieved using a pure silica network. There was considerable reduction in the silica particle size with more homogeneous distribution in the matrix when imide spacer groups were introduced in the silica network. The tan δ spectra obtained from dynamic thermal mechanical analysis shows a large increase in the glass transition temperature with increasing silica content for the compatibilized system in contrast to the un‐compatibilized one. Mechanical properties of the polyimide composites improved due to better interaction between the organic and inorganic phases. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2521–2531, 2005     

Multiscale analysis of nanoparticles size effects on thermal,elastic, and viscoelastic properties of nano-reinforced polymers

Dependency of microstructural organization, thermal, and mechanical properties of reinforced polymers on the size of the fillers was investigated on model nano-reinforced polymers. Binary systems made of poly(methyl methacrylate) and silica spheres were prepared. While volume fraction was kept constant, silica sphere diameters were varied from 500 nm down to 15 nm. X-ray scattering techniques along with static and dynamic mechanical analysis were conducted on the different prepared binary systems. From our experimental results, it appears that decreasing particle size lead to reduced interchain distances which could be interpreted as matrix densification. In addition, intrachain distance reflecting distance between two carbonyl groups within the same chain was also affected by particle size. Decrease of such distance was interpreted as local segmental rotation induced by size reduction. From mechanical aspects, reducing the size enhanced elastic properties, as evidenced by the increase in the elastic modulus. Dynamic analysis also confirmed such trend where the storage modulus increases for sample with smaller silica particle. Chain mobility quantified through the composite glass transition and the damping factor revealed size-induced mobility restriction through the observed increase of the glass transition. Particle size, when less than 60 nm, appeared as an important parameter contribution to material properties enhancement through multiscale microstructural characterization and mechanical analysis.     

Surface‐modified silica nanoparticles for reinforcement of PMMA

Polymethyl methacrylate (PMMA) was introduced onto the surface of silica nanoparticles by particle pretreatment using silane coupling agent (γ‐methacryloxypropyl trimethoxy silane, KH570) followed by solution polymerization. The modified silica nanoparticles were characterized by Fourier‐transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). Sedimentation tests and lipophilic degree (LD) measurements were also performed to observe the compatibility between the modified silica nanoparticles and organic solvents. Thereafter, the PMMA slices reinforced by silica‐nanoparticle were prepared by in situ bulk polymerization using modified silica nanoparticles accompanied with an initiator. The resultant polymers were characterized by UV–vis, Sclerometer, differential scanning calorimetry (DSC). The mechanical properties of the hybrid materials were measured. The results showed that the glass transition temperature, surface hardness, flexural strength as well as impact strength of the silica‐nanoparticle reinforced PMMA slices were improved. Moreover, the tensile properties of PMMA films doped with silica nanoparticles via solution blending were enhanced. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Multiscale modeling of interface debonding effect on mechanical properties of nanocomposites

Mechanical behavior of SiO₂ nanoparticle‐epoxy matrix composites was investigated via finite element analysis with an emphasis on the nanofiller‐interphase debonding effect using a three‐dimensional nanoscale representative volume element (RVE). The new model, in which a cohesive zone material (CZM) layer is considered as an inclusion‐interphase bonding, can be applied to polymer nanocomposites reinforced by inclusions of different forms, including spherical, cylindrical, and platelet shapes. Upon validation by experimental data, the model was used to study the effects of interphase properties, nanoparticle size, and inclusion volume fraction on the mechanical properties of nanocomposites. According to the results, taking into account the inclusion‐interphase debonding provides more precise results compared with perfect bonding, especially in nanocomposites with nanoparticles of smaller size. Moreover, the outcomes disclosed that the amount of changes in the elastic modulus by particle size variation is higher when the relative thickness (the interphase thickness to the particle diameter ratio) increases. For relative thicknesses lower than a critical value, the particle size and the interphase properties have negligible effect on the elastic modulus of the nanocomposite, and the elastic modulus of nanocomposite mostly depends on nanofiller content. POLYM. COMPOS., 38:789–796, 2017. © 2015 Society of Plastics Engineers     

Effect of different fillers on physical,mechanical, and optical properties of styrenic‐based thermoplastic elastomers

The effects of different fillers on physical, mechanical, and optical properties of styrenic‐based thermoplastic elastomers were investigated by experimental study. Poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] block copolymer (SEBS)‐based thermoplastic elastomer composites were prepared in a co‐rotating intermeshing twin‐screw extruder, using silica and calcite as filler materials with three different particle sizes. The loading ratios in the composites were varied. Hardness, density, tensile strength, tear strength, compression set, wear resistance, transmittance, and haze measurements were performed. Thermal properties and morphological structure were investigated by differential scanning calorimeter (DSC) and scanning electron microscopy (SEM), respectively. The results show that, an interaction between silica and the polymer matrix exists, whereas calcite does not show any interaction with the polymer. Therefore, it is concluded that, calcium carbonate can be used in the composite as filler for cost efficiency, whereas silica can be used as reinforcing material in SEBS‐based thermoplastic elastomer composites, when optical properties are also concerned. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers