Preparation of PFSA‐PVA/PSf hollow fiber membrane for IPA/H2O pervaporation process

Using Na⁺ form of perfluorosulfonic acid (PFSA) and poly(vinyl alcohol) (PVA) as coating materials, polysulfone (PSf) hollow fiber ultrafiltration membrane as a substrate membrane, PFSA‐PVA/PSf hollow fiber composite membrane was fabricated by dip‐coating method. The membranes were post‐treated by two methods of heat treatment and by both heat treatment and chemical crosslinking. Maleic anhydride (MAC) aqueous solution was used as chemical crosslinking agent using 0.5 wt % H₂SO₄ as a catalyst. PFSA‐PVA/PSf hollow fiber composite membranes were used for the pervaporation (PV) separation of isopropanol (IPA)/H₂O mixture. Based on the experimental results, PFSA‐PVA/PSf hollow fiber composite membrane is suitable for the PV dehydration of IPA/H₂O solution. With the increment of heat treatment temperature, the separation factor increased and the total permeation flux decreased. The addition of PVA in PFSA‐PVA coating solution was favorable for the improvement of the separation factor of the composite membranes post‐treated by heat treatment. Compared with the membranes by heat treatment, the separation factors of the composite membranes post‐treated by both heat treatment and chemical crosslinking were evidently improved and reached to be about 520 for 95/5 IPA/water. The membranes post‐treated by heat had some cracks which disappeared after chemical crosslinking for a proper time. Effects of feed temperature on PV performance had some differences for the membranes with different composition of coating layer. The composite membranes with the higher mass fraction of PVA in PFSA‐PVA coating solution were more sensitive to temperature. It was concluded that the proper preparation conditions for the composite membranes were as follows: firstly, heated at 160°C for 1 h, then chemical crosslinking at 40°C for 3 h in 4% MAC aqueous solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Pervaporation of water/alcohol mixtures through chitosan/cellulose acetate composite hollow‐fiber membranes

For the purpose of separating aqueous alcohol by the use of pervaporation technique, a composite membrane of chitosan (CT) dip‐coated cellulose acetate (CA) hollow‐fiber membranes, CT‐d‐CA, was investigated. The effects of air‐gap distance in the spinning of CA hollow‐fiber membranes, chitosan concentration, and sorts of aqueous alcohol solutions on the pervaporation performances were studied. Compared with unmodified CA hollow‐fiber membrane, the CT‐d‐CA composite hollow‐fiber membrane effectively increases the permselectivity of water. The thickness of coating layer increases with an increase in chitosan concentration. As the concentration of chitosan solution increased, the permeation rate decreased and the concentration of water in the permeate increased. In addition, the effects of feed composition and feed solution temperature on the pervaporation performances were also investigated. The permeation rate and water content in permeate at 25°C for a 90 wt % aqueous isopropanol solution through the CT‐d‐CA composite hollow‐fiber membrane with a 5‐cm air‐gap distance spun, 2 wt % chitosan dip‐coated system were 169.5 g/m² h and 98.9 wt %, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1562–1568, 2004     

影响渗透汽化中空纤维复合膜分离性能的制备工艺研究

采用聚乙烯醇（ＰＶＡ）为分离层的模材料,以浸涂工艺把ＰＶＡ复合到聚砜（ＰＳ）或聚丙烯腈（ＰＡＮ）的中空纤维支撑层上,在长度为０．４ｍ的不锈钢管中组装若干根中空纤维复合膜测定对乙醇水溶液的渗透汽化（ＰＶ）分离性能。结果表明,ＰＶＡ／ＰＡＮ中空纤维复合膜的性能优于ＰＶＡ／ＰＳ,内径较大（１．３ｍｍ）的优于内径上（０．４ｍｍ）者,ＰＶＡ水溶液在中空纤维支撑层上的涂复次数对复合膜ＰＶ分离性能、以及ＰＶＡ／     

Preparation of asymmetric PVA membranes using ternary system composed of polymer and cosolvent

Integrally skinned PVA membranes have been prepared from PVA/NMP/water system by the phase inversion method in 2‐propanol bath, and the pervaporation characteristics of these membranes were investigated. With an increase in the NMP content in the polymer solution, the formation of skin layer depended on the NMP content in the cosolvent, and the overall morphology of membranes changed from porous to dense structure. Particularly, PVA membranes showed an asymmetric structure composed of a dense skin layer and a porous sublayer with finger‐like type and cellular structure in solvents of 50–60% NMP compositions. The experimental results from the pervaporation separation of MTBE and methanol mixtures were also in good agreement with the morphology for the formation of skin layer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2884–2890, 2003     

Effect of polyvinylpyrrolidone molecular weights on morphology,oil/water separation,mechanical and thermal properties of polyetherimide/polyvinylpyrrolidone hollow fiber membranes

We prepared polyetherimide (PEI) hollow fiber membranes using polyvinylpyrrolidones (PVP) with different molecular weights (PVP 10,000, PVP 40,000, and PVP 1,300,000) as additives for oil/water separation. Asymmetric hollow fiber membranes were fabricated by wet phase inversion technique from 25 wt % or 30 wt % solids of 20 : 5 : 75 or 20 : 10 : 70 (weight ratio) PEI/PVP/N‐metyl‐2‐pyrrolidone (NMP) solutions and a 95 : 5 NMP/water solution was used as bore fluid to eliminate resistance on the internal surface. Effects of PVP molecular weights on morphology, oil‐surfactant‐water separation characteristics, mechanical, and thermal properties of PEI/PVP hollow fiber membranes were investigated. It was found that an increase in PVP molecular weight and percentage in PEI/PVP dope solution resulted in the membrane morphology change from the finger‐like structure to the spongy structure. Without sodium hypochlorite posttreatment, hollow fiber membranes with higher PVP molecular weights had a higher rejection but with a lower water flux. For oil‐surfactant‐water emulsion systems (1600 ppm surfactant of sodium dodecylbenzenesulfonate and 2500 ppm oil of n‐decane), experimental results illustrated that the rejection rates for surfactant, total organic carbon, and oil were 76.1 ≈ 79.8%, 91.0 ≈ 93.0%, and more than 99%, respectively. Based on the glass transition temperature values, PVP existed in hollow fiber membranes and resulted in the hydrophilicity of membranes. In addition, using NaOCl as a posttreatment agent for membranes showed a significant improvement in membrane permeability for PVP with a molecular weight of 1300 K, whereas the elongation at break of the treated hollow fiber membranes decreased significantly. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2220–2233, 1999     

全氟磺酸改性聚乙烯醇渗透汽化膜分离乙酸乙酯-水溶液

以聚乙烯醇(PVA)为原材料,全氟磺酸(PFSA)为共混改性材料,以聚丙烯腈(PAN)中空纤维超滤膜为底膜制备了PVAfPAN、PVA-PFSA/PAN复合膜,并用于乙酸乙酯脱水.考察了共混涂膜液中PVA、PFSA配比,交联剂酒石酸(Tat)用量以及原料液温度与浓度对PVA、PAN、PVA-PFSA、PAN复合膜分离件能的影响.实验结果表明,Tac交联的PVA,PAN、PVA-PFSA/PAN复合膜均对水具有较好的分离选择性.共混涂膜液中PVA/PFSA质量比为1/1、Tac/PVA质量比为l/5时所制备的PVA-PFSA/PAN复合膜渗透汽化分离性能最佳.40下℃此复合膜用于分离98%(wt)的乙酸乙酯水溶液时,其渗透通量和分离因予分别为81.1 g·m-2·h-1和1890.同样条件下,与交联PVA/PAN复合膜相比,交联PVA-PFSA/PAN复合膜的渗透通量显著提高.     

Perfluorosulfonic acid—Tetraethoxysilane/polyacrylonitrile (PFSA‐TEOS/PAN) hollow fiber composite membranes prepared for pervaporation dehydration of ethyl acetate–water solutions

Preparation of organic‐inorganic composite membranes and their pervaporation (PV) permeation and separation characteristics for the aqueous solution of ethyl acetate were described. Polyacrylonitrile (PAN) hollow fiber ultrafiltration membrane as support membrane, the mixtures of perfluorosulfonic acid (PFSA) and tetraethoxysilane (TEOS) by the sol‐gel reaction as the coating solution, the PFSA‐TEOS/PAN hollow fiber composite membranes by the different annealing conditions were prepared. The swelling of PFSA in ethyl acetate aqueous solutions was inhibited with addition of TEOS. The PFSA‐TEOS/PAN composite membranes containing up to 30 wt % TEOS in coating solution exhibited high selectivity towards water, then the selectivity decreased and permeation flux increased with increasing the TEOS concentration more than 30 wt %. When the PFSA‐TEOS/PAN composite membranes were annealed, the separation factor increased with increasing annealing temperature and time. Higher annealing temperature and longer annealing time promoted the crosslinking reaction between PFSA and TEOS in PFSA‐TEOS/PAN composite membranes, leading to the enhanced selectivity towards water. For the PFSA/PAN and PFSA‐TEOS/PAN composite membrane with 5 and 30 wt % TEOS annealed at 90°C for 12 h, their PV performance of aqueous solution 98 wt % ethyl acetate were as follows: the separation factors were 30.8, 254 and 496, while their permeation flux were 1430, 513 and 205 g/m² h at 40°C, respectively. In addition, the PV performance of PFSA‐TEOS/PAN composite membranes was investigated at different feed solution temperature and concentration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

烧结温度对TiO2/不锈钢中空纤维复合膜结构和性能的影响

不锈钢中空纤维膜基膜孔径大,直接涂覆分离层容易产生表面缺陷。在二氧化钛悬浮液中加入聚乙烯醇作为黏结剂,通过真空辅助抽滤法在不锈钢中空纤维基膜表面形成一层均匀的分离层。通过高温烧结得到了TiO₂/不锈钢中空纤维复合膜,考察了烧结温度对于TiO₂/不锈钢中空纤维复合膜表面分离层形貌和结构的影响。不同烧结温度时,TiO₂/不锈钢中空纤维复合膜的表面形貌有所差异;随着烧结温度的升高,不锈钢复合膜的孔径和纯水通量均先升高再下降。当烧结温度为500℃时,表面涂层均匀,孔径分布集中,水通量较高。最后,以SPT-500膜测试了水包油乳液分离效果,分离效率达到99%以上,且具有良好的抗污染性能。     

Pervaporation separation of water/isopropanol mixtures through crosslinked carboxymethyl chitosan/polysulfone hollow‐fiber composite membranes

Carboxymethyl chitosan (CMCS)/polysulfone (PS) hollow‐fiber composite membranes were prepared through glutaraldehyde (GA) as the crosslinking agent and PS hollow‐fiber ultrafiltration membrane as the support. The permeation and separation characteristics for dehydration of isopropanol were investigated by the pervaporation method. Pure chitosan, carboxymethyl chitosan, and crosslinked carboxymethyl chitosan membranes were characterized by Fourier transform infrared (FT‐IR) spectroscopy and X‐ray diffraction (XRD) to study the crosslinking reaction mechanism and degree of crystallinity, respectively. The effects of feed composition, crosslinking agent, membrane thickness, and feed temperature on membrane performance were investigated. The results show that the crosslinked CMCS/PS hollow‐fiber composite membranes possess high selectivity and promising permeability. The permeation flux and separation factor for isopropanol/water is 38.6 g/m²h and 3238.5, using 87.5 wt % isopropanol concentration at 45°C, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1959–1965, 2007     

Pore structure and properties of poly(ether ether ketone) hollow fiber membranes: influence of solvent‐induced crystallization during extraction

Poly(ether ether ketone) (PEEK) hollow fiber membranes were prepared by a thermally induced phase separation method with polyetherimide as diluent, and N‐methyl pyrrolidone (NMP), dichloromethane and a composite extractant composed of NMP, ethanolamine and water as extractant. The effects of the different solvents induced crystallization on the pore structure during extraction and the properties of the PEEK hollow fiber membranes were investigated in detail. The crystallization behaviors of the membranes were characterized by DSC and XRD. The effect of the extractants on the microscopic morphologies, pore structures, water fluxes and mechanical properties of the membranes were investigated. The results showed that the extraction ability of the composite extractant was the most significant, followed by NMP and dichloromethane. The crystallinity of the hollow fiber was 39.0% before extraction and was elevated to 39.2% after the extraction with NMP, 46.6% with dichloromethane and 46.7% with the composite extractant, which shows that dichloromethane and the composite extractant have strong ability to induce the crystallization of PEEK. The inner and outer surfaces of the membranes obtained after extraction by the composite extractant had the largest pore size and the highest surface porosity. The most probable pore diameter of the membranes obtained after extraction by NMP, dichloromethane and the composite extractant was 23.26 nm, 24.43 nm and 24.43 nm, respectively, which indicated that solvent‐induced crystallization was beneficial for the formation of larger pores. The pure water flux of the PEEK membrane prepared by the composite extractant was the largest, but the tensile strength was the lowest. © 2019 Society of Chemical Industry     

Morphological and separation performance study of polysulfone/titanium dioxide (PSF/TiO2) ultrafiltration membranes for humic acid removal

In this study, polysulfone (PSF) hollow fiber membranes with enhanced performance for humic acid removal were prepared from a dope solution containing PSF/DMAc/PVP/TiO₂. The main reason for adding titanium oxide during dope solution preparation was to enhance the antifouling properties of membranes prepared. In the spinning process, air gap distance was varied in order to produce different properties of the hollow fiber membranes. Characterizations were conducted to determine membrane properties such as pure water flux, molecular weight cut off (MWCO), humic acid (HA) rejection and resistance to fouling tendency. The results indicated that the pure water flux and MWCO of membranes increased with an increase in air gap distance while HA retention decreased significantly with increasing air gap. Due to this, it is found that the PSF/TiO₂ membrane spun at zero air gap was the best amongst the membranes produced and demonstrated > 90% HA rejection. Analytical results from FESEM and AFM also provided supporting evidence to the experimental results obtained. Based on the anti-fouling performance investigation, it was found that membranes with the addition of TiO₂ were excellent in mitigating fouling particularly in reducing the fouling resistances due to concentration polarization, cake layer formation and absorption.     

Hydrophilic modification of high‐strength polyvinylidene fluoride hollow fiber membrane

The polyvinylidene fluoride (PVDF)/polyvinyl alcohol (PVA) polymer solutions were coated on the outer surface of PVDF matrix hollow fiber membrane. On the principle of the homogeneous‐reinforced (HR) membrane technology, the reinforced PVDF/PVA (RFA) hollow fiber membranes prepared through the dry‐wet spinning method. The performance of the RFA membranes varies with the PVA concentration in the polymer solution and is characterized in terms of pure water flux (PWF), porosity, a mechanical strength test, and morphology observations by a scanning electron microscopy (SEM). The results of this study indicate that PVA can apparently improve the hydrophilicity of the PVDF hollow fiber membranes. The growing enrichment of the hydrophilic components PVA on the membrane surface is determined by X‐ray photoelectron spectroscopy. The RFA membranes have a favorable interfacial bonding between the coating layer (PVDF/PVA) and the matrix membrane (PVDF hollow fiber membrane), as shown by SEM. The elongation at break of the RFA membranes increases much more than that of the matrix membrane that is endowed with the better flexibility of the membrane performance. PWF decreases much more compared with that of the matrix membrane. The RFA membranes have a lower flux decline degree during the process of protein solution and ink solution filtration compared with that of the matrix membrane. POLYM. ENG. SCI., 54:276–287, 2014. © 2013 Society of Plastics Engineers     

热处理条件对PVA/PAN和PPVA/PAN渗透汽化复合膜分离性能的影响

制备了以聚乙烯醇（PVA）、磷酸酯化聚乙烯醇（PPVA）和活性分离层的PVA／PAN、PPVA／PAN渗透汽化复合膜并用于乙醇－水恒沸混合物的分离。考察了热处理条件对复合膜分离性能及吸附性能的影响。结果表明,复合膜的分离性能主要是由热处理温度决定的,并且,PPVA／PAN复合膜比PVA／PAN复合膜具有更好的分离性能。确定了最佳的热处理条件,对于PVA／PAN复合膜：在403K下,热处理时间不小于4h,对于PPAV／PAN复合膜：在423K下,热处理时间不小于2h。     

Comparative behavior of PVA/PAN and PVA/PES composite pervaporation membranes in the pervaporative dehydration of caprolactam

Flat‐sheet composite membranes were developed by the traditional phase inversion technique using poly;(vinyl alcohol) (PVA). PVA composite pervaporation (PV) membranes were prepared with crosslinked PVA selective layer and porous polyacrylonitrile (PAN) and polyether sulfone (PES) substrate layer material as supports for separating heat sensitivity substance ε‐caprolactam (CPL) from CPL/water mixtures. Glutaraldehyde was used as crosslinking agent. The effect of the composition of glutaraldehyde on membrane stability and structure were investigated. The operating parameters, such as feed concentration and operating temperature, remarkably affected PV performance of the composite membranes. The composite membranes with PVA casted on PAN (PVA/PAN) showed superior PV performance than that casted on PES (PVA/PES). This study has also shown that the type of porous support plays an important role in the PV performance. As a result, this work has presented the information needed of the behavior of PV membranes for dehydration applications of industrial caprolactam. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 4005–4011, 2007     

Modified poly(vinylidene fluoride) hollow fiber composite membranes reinforced by hydroxyapatite nanocrystal whiskers

The modified poly(vinylidene fluoride) (PVDF) hollow fiber composite membranes reinforced by hydroxyapatite (HAP) nanocrystal whiskers were fabricated with wet‐spinning method. The PVDF/HAP/N‐methyl‐2‐pyrrolidone dope solutions experienced delayed demixing mechanism, and the precipitation rate slightly increased as the HAP whisker content increased. The cross sections of PVDF‐HAP and neat PVDF hollow fiber composite membranes were composed of five distinct layers: two skin layers, two finger‐like sublayers, and a sponge‐like layer. The Young's modulus of and tensile strength of the PVDF‐HAP hollow fiber membranes gradually increased with the addition of nano‐HAP whiskers. The elongation ratio was also improved, which was different from the polymeric membranes modified by other inorganic nanofillers. The permeation flux of the PVDF‐HAP hollow fiber membranes slightly increased with the increase of HAP content in the composite membranes as its hydrophilicity was improved. The crystallization behaviors of PVDF in the composite membranes were also investigated. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of polyethylene glycol molecular weights and concentrations on polyethersulfone hollow fiber ultrafiltration membranes

Polyethersulfone (PES) hollow‐fiber membranes were fabricated using poly(ethyleneglycol) (PEG) with different molecular weights (MW = PEG200, PEG600, PEG2000, PEG6000, and PEG10000) and poly(vinyl pyrrolidone) PVP40000 as additives and N‐methyl‐2‐pyrrolidone (NMP) as a solvent. Asymmetric hollow‐fiber membranes were spun by a wet phase‐inversion method from 25 wt % solids of 20 : 5 : 75 (weight ratio) PES/PEG/NMP or 18 : 7 : 75 of PES/(PEG600 + PVP40000)/NMP solutions, whereas both the bore fluid and the external coagulant were water. Effects of PEG molecular weights and PEG600 concentrations in the dope solution on separation properties, morphology, and mechanical properties of PES hollow‐fiber membranes were investigated. The membrane structures of PES hollow‐fiber membranes including cross section, external surface, and internal surface were characterized by scanning electron microscopy and the mechanical properties of PES hollow‐fiber membranes were discussed. Bovine serum albumin (BSA, MW 67,000), chicken egg albumin (CEA, MW 45,000), and lysozyme (MW 14,400) were used for the measurement of rejection. It was found that with an increase of PEG molecular weights from 200 to 10,000 in the dope solution, membrane structures were changed from double‐layer fingerlike structure to voids in the shape of spheres or ellipsoids; moreover, there were crack phenomena on the internal surfaces and external surfaces of PES hollow‐fiber membranes, pure water permeation fluxes increased from 22.0 to 64.0 L m^?2 h^?1 bar^?1, rejections of three protein for PES/PEG hollow‐fiber membranes were not significant, and changes in mechanical properties were decreased. Besides, with a decrease of PEG600 concentrations in the dope solution, permeation flux and elongation at break decreased, whereas the addition of PVP40000 in the dope solution resulted in more smooth surfaces (internal or external) of PES/(PEG600 + PVP40000) hollow‐fiber membranes than those of PES/PEG hollow‐fiber membranes. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3398–3407, 2004     

PVA-TEOS/PAN渗透汽化膜的制备及其乙酸乙酯脱水

以聚丙烯腈(PAN)中空纤维超滤膜为底膜,以聚乙烯醇(PVA)和正硅酸乙酯(TEOS)的混合液为涂膜液,采用溶胶-凝胶法制备了PVA-TEOS/PAN渗透汽化复合膜,并用于乙酸乙酯脱水. FT-IR和XRD谱图证实复合膜表层中由于PVA与TEOS的交联反应而形成了Si?O?C共价键,且PVA的结晶度下降. 另外,利用静态接触角测量对复合膜表层的亲水性进行了表征. 考察了复合膜在乙酸乙酯水溶液中的溶胀性能及涂膜液中TEOS含量和料液温度与浓度对PVA-TEOS/PAN复合膜分离性能的影响. 结果表明,TEOS的加入有效降低了复合膜在乙酸乙酯水溶液中的溶胀度,使其对水具有较好的分离选择性. 40℃下,涂膜液中TEOS质量含量分别为5%和30%的PVA-TEOS/PAN复合膜分离98%的乙酸乙酯水溶液时,其分离因子分别为2830和4448,渗透通量分别为49.4和41.4 g/(m2×h).     

Mass transfer simulation on pervaporation dehydration of ethanol through hollow fiber NaA zeolite membranes

A multi‐layer series‐resistance mass transfer model was developed to simulate mass transfer behaviors of water/ethanol mixture through hollow fiber NaA zeolite membranes. The mass transfer through zeolite layer was described by Maxwell‐Stefan mechanism based on adsorption and diffusion parameters obtained from molecular simulation. The mass transfer through asymmetric hollow fiber support was described by dusty gas model involving Knudsen diffusion and viscous flow. It was found that the sponge‐like layer of support besides of zeolite layer made an important contribution to overall membrane transfer resistance while the finger‐like layer had less effect. When permeate pressure shifted from 0.2 to 7.5 kPa, the mass transfer resistance contribution of sponge‐like layer varied from 27.1 to 17.8%. Effects of microstructure parameters of support on mass transfer through membrane were investigated extensively. Large pore size and thin thickness for sponge‐like layer of support were beneficial to improve water permeation flux. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2468–2478, 2016     

Preparation and characterization of PVA/SA composite nanofiltration membranes

Nanofiltration (NF) composite membranes based on poly(vinyl alcohol) (PVA) and sodium alginate (SA) were prepared by coating PVA/SA (95/5 in wt %) mixture solutions on microporous polysulfone (PSF) supports. For the formation of a defect free thin active layer on a support, the PSF support was multi‐coated with a dilute PVA/SA blend solution. The PVA/SA active layer formed was crosslinked at room temperature by using an acetone solution containing glutaraldehyde as a crosslinking agent. The prepared composite membranes were characterized with a scanning electron microscopy (SEM), a Fourier transform infrared spectroscopy (FTIR), an electrokinetic analyzer (EKA) and permeation tests: The thicknesses of the active layers were about 0.25 μm and 0.01 μm depending on the preparation conditions. The crosslinking reaction of the active layers were completed in less than three minutes via the formation of acetal linkage. The surface of the PVA/SA composite membrane was found to be anionic. The permeation properties of the composite membrane were as follows: 1.3 m³/m² day of flux and > 95% of rejection at 200 psi for 1000 ppm PEG600 solution. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 347–354, 2000     

Polymer membranes for separating organic mixtures

Polyvinyl alcohol (PVA), polyacrylonitrile (PAN), and cellulose ester were respectively chosen as the separation layer and the support in the composite membranes based on the concept of the solubility parameter and the permselectivities for separating ethanol/water mixture, isopropanol/water mixture, and caprolactam/water mixture. The effects of the membrane materials and the construction of the composite membrane on the separation performance were preliminary discussed. The separation performance of the membranes prepared by several making‐membrane techniques, i.e., the polymer solution making‐membrane technique, and the membrane treatment technique (heat treatment, organic solvent modification) were presented. The composite membranes of PVA/PAN and PVA/cellulose acetate, and cellulose triacetate hollow fiber membrane modified, which possess good performance in separating the organic systems, were developed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1160–1164, 2006