基于多用户反馈的判决反馈均衡器的研究

本文提出的一种新颖的基于多用户反馈的判决反馈均衡器,解决了在CDMA多用户检测中传统自适应判决反馈均衡器误码率高、系统容量小的缺点.它由具有误差反馈滤波器的判决反馈均衡器(Decision Feedback Equalizer with Error Feedback Filter,DFE-EFF)构成,并在判决后反馈多用户数据抵消多址干扰(多用户反馈干扰抵消).文中给出其结构图,分析各种判决反馈均衡算法.理论证明,具有误差反馈滤波器的多用户反馈干扰抵消判决反馈均衡器(多用户反馈干扰抵消DFE-EFF)较各种判决反馈均衡器为最优,它能同时有效处理ISI,MAI和噪声的干扰.仿真结果表明,在误码率性能和系统容量两方面,多用户反馈干扰抵消DFE-EFF比DFE、DFE-EFF均有较大改善.     

运用误差反馈的判决反馈均衡器的性能分析

判决反馈均衡器（Decision Feedback Equalizer，DFE）能补偿具有严重符号间干扰（Inter Symbol Interference，ISI）的信道，且不存在线性均衡器增强噪声的影响。而在其基础上改进的运用误差反馈的DFE，可利用误差反馈滤波器来减少传统DFE中存在的误差信号的相关性，同时其硬件实现的复杂度没有明显提高。理论分析和仿真表明，这种方法比传统的DFE更有效，特别是针对信道有严重符号间干扰的情况。     

慢衰落信道下的自适应MIMO检测算法

针对现有V-BLAST检测算法复杂度高的问题,本文提出了一种适用于慢衰落信道环境下的自适应MIMO检测算法。该算法首先利用基于最小均方误差准则的排序干扰抵消算法获得信号检测顺序和初始滤波器系数;利用信道之间的相关性,应用最小均方误差（LMS）算法到判决反馈均衡（DFE）结构中,完成滤波器系数的更新,从而避免了大量的矩阵求逆操作。仿真结果表明,与传统的MMSE-OSIC算法相比,本文算法在检测性能上略有下降,但具有更低的计算复杂度和更高的处理效率。      

非正交多脉冲调制的QR分解多用户检测

针对加性高斯白噪声信道下的多用户非正交多脉冲调制系统,提出了基于QR分解的非相干判决反馈多用户检测器。该检测器通过QR分解矩阵变换,利用功率较强用户的判决信息来进行干扰抵消,可以有效消除用户间的多址干扰。而在各用户内,针对多脉冲调制技术,提出了一种线性解相关运算来进行非相干检测。同时,考虑解相关运算中矩阵求逆的复杂度比较高,进一步提出了一种软干扰抵消检测器。仿真结果表明所提的两种多用户检测算法可以有效消除非正交调制所造成的多址干扰,极大地提高功率较弱用户的性能,并且所提软干扰抵消检测器通过避免矩阵求逆降低了计算复杂度,同时检测性能没有损失。      

低计算复杂度的多级软判决均衡器用于干扰抑制

针对通信系统中非线性均衡器的计算复杂度问题,提出一种基于最低误码率准则的多级软判决均衡器.通过调节各级均衡器的拒绝门限,可使多级软判决均衡器在计算复杂度与误码率之间取得折衷.仿真表明:对于扩展的二元相移键控信号,在相对强的调频信号和调幅信号的联合干扰下,匹配滤波器和基于最小均方误差准则的线性均衡器已失效,而基于最低误码率准则的多级软判决均衡器仍能表现出良好的性能,并且大大减少计算复杂度.此外,还发现一个有趣的结果,即多个不同的非线性均衡器的协作可获得比单个均衡器更优的性能.     

一种T/4分数间隔预测判决反馈盲均衡算法

为了消除由深衰落信道引起的严重码间干扰,本文给出一种基于改进双模式多模算法的 T/4 分数间隔预测判决反馈均衡器.该均衡器采用改进的双模式多模算法独立优化前向、反馈滤波器,前向滤波器采用 T/4 分数间隔,反馈滤波器采用预测结构,仍为符号速率.在两种深衰落信道条件下仿真实验表明,本文给出的均衡器能够避免传统判决反馈均衡器的误收敛情况;同时其稳态均方误差小于基于常模算法的 T/4 分数间隔均衡器、基于常模算法的 T/4 分数间隔判决反馈均衡器,以及基于双模式多模算法的 T/4 分数间隔预测判决反馈均衡器,更适合处理 QAM 信号.     

用判决反馈自适应均衡器抑制多音干扰

从理论上分析了在QPSK系统中用判决反馈自适应均衡器抑制多音干扰的性能,给出了均衡器最佳系数与最小均方误差计算公式,指出QPSK系统中的均衡器能同时起到抑制多音干扰的作用。利用此性能可使设备简化。     

基于FPGA的分数间隔预测判决反馈均衡器的设计与实现

针对高阶QAM信号,本文设计实现了一种基于FPGA的分数间隔预测判决反馈均衡器.前向滤波器采用分数间隔结构,反馈部分采用预测结构,仍保持符号速率.该均衡器充分结合了分数间隔均衡器与预测判决反馈均衡器的优势,能够消除由深衰落信道引起的严重码间干扰.同时,该均衡器采用简化后的双模式多模算法独立优化前向、反馈滤波器,简化算法...     

改善判决反馈均衡器性能的一种新方法

判决反馈均衡器是一种算法复杂度较低、性能也较好、并在实际中得到广泛应用的均衡器。它的一个内在的缺陷是错误判决结果反馈所引起的性能损失。利用判决反馈均衡器中前向滤波器输出中的信息,提出了一种改善判决反馈均衡器性能的方法,并给出改进后判决反馈均衡器的结构和实现方法。仿真结果证明了该方法的有效性。     

联合均衡块迭代软判决反馈干扰抵消接收机

CDMA扩频通信系统在低扩频比时,路径间干扰(IPI, inter-path interference)变得非常严重。本文将块迭代干扰抵消同MMSE均衡器相结合,提出了一种适用于CDMA扩频通信系统低扩频比情况下的联合均衡块迭代软判决反馈干扰抵消(MMSE-BIIC)接收机结构。理论分析与计算机仿真表明,本文提出的MMSE-BIIC接收机同传统的Rake接收机、线性MMSE均衡器以及多级干扰抵消接收机相比在性能上有较大改善。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks