Kenics静态混合器在水平液固循环流化床中的研究

为了解决水平液固循环流化床中颗粒分布不均匀问题,在内径29 mm、长4 m的水平有机玻璃管流化床内放入Kenics静态混合器,采用CCD图像测量与数据处理系统考察静态混合器的结构、个数、安装位置对液固二相流中颗粒分布的影响;同时,利用U型管压差计考察不同条件下静态混合器的压降。实验结果表明:Kenics静态混合器能明显地改善管内颗粒分布情况;单个扭率Y=3.5的Kenics静态混合器压降最小;2个扭率Y=3.5的Kenics静态混合器间距为40 mm时对颗粒分布影响长度是最长的。     

带有Kenics静态混合器的水平液固两相流化床换热管的压降研究

以饱和硫酸钙为介质,在安装Kenics静态混合器的水平液固两相流化床换热管上进行实验研究,考察介质流速、Kenics静态混合器扭率、颗粒体积分数及颗粒尺寸对压降的影响,并与冷态实验条件下的压降变化规律进行比较。结果表明：同等操作条件,安装Kenics静态混合器后压降比安装前提高20%～140%;压降随雷诺数的增大而增大,随Kenics静态混合器扭率的增大而减小;颗粒体积分数对压降也有影响。根据实验数据,得出了稳定操作条件下压降与上述影响因素之间的经验关联式,为带有Kenics静态混合器的水平液固两相流化床换热器的设计提供计算依据。     

水平液固循环流化床颗粒分布状况的实验研究

为使水平液固循环流化床换热器更好地强化传热和防垢、除垢,管中颗粒的分布是关键,因此对卧式换热器前管箱进行改造,采用双进料口并在前管箱加入挡板,使得颗粒在管路中分布均匀。在实验中自行设计了一套水平多管液固循环流化床实验装置。采用CCD图像采集系统,获得了颗粒的运动及分布状况。研究表明:挡板的角度、颗粒密度等对颗粒分布性能都有较大影响。通过对实验结果的分析,得到了使固体颗粒在管束中分布效果较好的挡板角度以及较适宜颗粒分布的运行参数,以指导工程放大应用。     

水平液固循环流化床换热器传热性能研究

通过对管内插入Kenics静态混合器的水平液固循环流化床换热器进行数值模拟和实验研究,考察了静态混合器扭率对颗粒分布、传热性能和流阻性能的影响。结果表明:水平管内安装Kenics静态混合器的扭率越小,管内颗粒分布均匀距离越长。当雷诺数在10 000—45 000之间,扭率为1.5,2.5,4,6的Kenics静态混合器的综合性能评价指标PEC均大于1,说明了水平流化床换热器插入Kenics静态混合器能够改善传热。当流速大于1.5 m/s,在2 m长的水平流化床换热器内安装一个扭率为1.5的Kenics静态混合器能够达到改善颗粒分布和提高传热性能的效果。     

水平液固循环流化床换热器传热性能评价

对管内插入Kenics静态混合器的水平液固循环流化床换热器进行实验研究,实验考察了静态混合器扭率、静态混合器安装方式、液体流速、颗粒体积分数对传热性能和流阻性能的影响,并运用综合强化传热性能评价指标（PEC）对其进行分析。实验发现,传热性能和阻力系数均随扭率增加而减小。当雷诺数在10000~45000之间时,扭率为1.5、2、2.5、3.5的Kenics静态混合器的PEC指标均大于1,说明了水平流化床换热器插入Kenics静态混合器能够改善传热。在雷诺数达到25000左右、Kenics静态混合器扭率为2.5、颗粒体积分数为4%时,水平流化床换热器的PEC指标最高达到1.18。当两个扭率均为2.5的Kenics静态混合器安装间距为200mm时,水平流化床换热器的PEC指标最高。     

液固循环流化床换热器中固体颗粒分布

利用CCD图像测量与数据处理系统对多管液固循环流化床换热器中的两相流动特性进行了研究。探讨了下管箱中的分布板结构对固体粒子的体积分数分布、固体粒子的速度分布,以及液固两相流压降的影响。实验结果表明:在循环流化床换热器进口段安装适当结构的多孔板分布器,即多孔板的面积小于床层截面积,且床中心处的遮挡面积大于边缘处的遮挡面积,可以有效地提高固相速度的均匀程度,在较高流速下,能较好地改善固体颗粒在管束中的不均匀分布。     

The axial hydrodynamic behavior in a liquid-solid circulating fluidized bed

Based on experimental results from a 7.6 cm I. D. and 3 m high liquid–solid circulating fluidized bed, the liquid–solid circulating fluidization regime has been separated into two zones: the initial circulating fluidization zone and the fully developed circulating fluidization zone. The distinct hydrodynamic behavior and the influence of particle properties in the two circulating fluidization zones have been studied. The overall flow structure in LSCFB, although still somewhat non–uniform, is much more uniform than that in a gas-solid CFB. Our experimental results also show that the axial flow characteristics and the regime transition can be strongly affected by the particle density. The stable operation range of the circulating fluidization system and the influences of some associated factors, such as the solids inventory and the particle density, were also investigated for the first time.     

Continuous enzymatic polymerization of phenol in a liquid-solid circulating fluidized bed

A liquid-solid circulating fluidized bed (LSCFB) system consisting of 3.8 cm I.D. and 4 m high riser and 12 cm I.D. and 3.5 m high down-comer was investigated in this study for the continuous polymerization of phenol. Approximately 8.5 kg immobilized particles containing soybean seed hull peroxidase enzymes were applied in the LSCFB system. The continuous enzymatic polymerization was carried out in the riser section by introducing phenol and hydrogen peroxide at the entrance of the riser. Under optimized hydrodynamic conditions and by keeping the molar concentration ratio of phenol to H₂O₂ of 1:2, 54% conversion of phenol was achieved. The down-comer of the LSCFB was utilized for the regeneration of the coated immobilized enzyme particles. The effect of the superficial liquid velocity and an initial substrate concentration was studied. Our experimental results show that an enzymatic reaction and the regeneration of the biocatalysts can be carried out simultaneously and independently in the LSCFB system. Furthermore, this work opens the possibilities for many bioprocesses where the deactivation of the biocatalysts is a major problem and the regeneration of the biocatalysts is required.     

循环流化床换热器中液固二相流的数值模拟

在循环流化床换热器的流体中加入固体粒子,可以对边界层有扰动作用,加快换热器中的传质与传热.对流化床换热器中的液固二相进行数值模拟,分别讨论了固体粒子对液体动量方程、k-ε方程及能量方程的影响,在单液相方程的基础上进行修正,建立了相应的液固二相流控制方程,确定了物理模型及边界条件.利用FLUENT进行数值计算,分别讨论了...     

Modeling of counter-current adsorption in continuous liquid-solid circulating fluidized bed adsorption chromatography

Continuous chromatography using a liquid-solid circulating fluidized bed (LSCFB) is an efficient and eco-friendly system used for the separation and purification of biomolecules and radioactive waste. It combines continuous counter-current adsorption and simultaneous regeneration of solids. Here, we developed a mathematical model to study the performance of these counter-current adsorbers using MATLAB^TM which is a fundamental tool for scale up. This model predicts the adsorption zone length and height equivalent to theoretical plates (HETPs). In addition, this work also illustrates the comparative performance studies of adsorption in a conventional packed bed, expanded bed and LSCFB in terms of HETP values. At lower velocities such as 0.35 cm/s, HETPs of the LSCFB, packed bed, expanded bed are 5, 12, 18 cm, respectively.     

高密度液固循环流化床流动特性研究及数值模拟

在φ80 mm×8000 mm的液固循环流化床提升管中,利用实心玻璃珠和常温水,采用实验和数值模拟相结合的方法对高密度液固循环流化床的流动特性进行了考察。实验发现,高密度液固提升管中,颗粒固含率和颗粒速度径向分布均为抛物线分布,轴向平均固含率分布总体上为下浓上稀的波动形式分布,颗粒在提升管中的流动表现出加速-减速-再加速直至充分发展的过程。这种分布特征与较高颗粒浓度、较高表观液速和颗粒循环速率及喷管式液体分布器的影响有关。液固提升管中固体颗粒的停留时间分布曲线均为尖而窄、较对称且没有明显拖尾的单峰分布,这表明颗粒基本是以弥散颗粒形式存在,颗粒停留时间分布较为均匀。通过将数值模拟结果与实验结果进行比较发现,模拟值与实验值吻合较好,说明所建立的数学模型较为合理,进一步通过数值模拟实验对颗粒密度和颗粒粒径对流动特性的影响规律进行了考察。     

Macroscopic properties of liquid-solid circulating fluidized bed with viscous liquid medium

Experiments were conducted in a liquid-solid circulating fluidized bed to study the effect of liquid viscosity and solids inventory on pressure gradient, critical transitional liquid velocity, onset average solids holdup, axial solids holdup distribution, average solids holdup and solids circulation rate in circulating fluidization regime with riser operated in fixed inventory mode. The results indicate that critical transitional liquid velocity decreases with increase in liquid viscosity. The onset average solids holdup, on the other hand, increases with increase in either auxiliary liquid velocity or solids inventory. The variation of axial solids holdup distribution, average solids holdup and solids circulation rate with liquid viscosity when solid inventory was 0.15 m was dissimilar with either 0.25 m or 0.35 m solid inventory. Correlations were proposed for estimating the average solids holdup and are satisfactorily compared with experimental values.     

Optimal design of liquid-solid circulating fluidized bed for continuous protein recovery

In recent years, liquid-solid circulating fluidized beds (LSCFBs) are being applied as a reactor system in a number of new applications. This study addresses optimal design of LSCFB system at the design stage for the continuous protein recovery. The operation of LSCFB system for continuous protein recovery is associated with several important objectives such as production rate and recovery of protein as well as the amount of ion exchange resin requirements, all of which need to be optimized simultaneously. In this study, an experimentally validated mathematical model was used to perform the multi-objective optimization of the LSCFB system at the design stage. In the optimization study, eight operating and design parameters were used as decision variables. These variables were chosen based on systematic sensitivity analysis of the system which showed complex interplay of the decision variables over the system performance indicators. Elitist non-dominated sorting genetic algorithm with its jumping gene adaptation (NSGA-II-aJG) was used to solve a number of two- and three-objective function optimization problems. The optimization resulted in Pareto optimal solutions, which provides a broad range of non-dominated solutions due to conflicting behavior of the decision variables on the system performance indicators. Compared to the optimization results obtained in the operating stage, the performance of the system was further improved at the design stage optimization as changes in physical dimensions of the LSCFB system can provide better performance than would have been possible by adjusting only the operating parameters.     

喷嘴对液固外循环流化床内含固体积分数的影响

设计了实现液固外循环流化床中颗粒正常循环的关键部件——喷嘴,利用CCD图像采集分析系统,获得了其换热管束内固体颗粒的分布情况,考察了液体流量、口径比、喷嘴安装位置、颗粒直径、颗粒初始加入量以及液体黏度对液固外循环流化床换热器管束内含固体积分数的影响。结果表明:口径比及喷嘴安装位置对提高管束内的含固体积分数都存在一个最佳值,颗粒直径、颗粒初始加入量以及液体黏度对管束内含固体积分数也具有较大的影响,同时还通过对实验数据的综合分析,得到了喷嘴在最佳安装位置下液固外循环流化床内含固体积分数的经验关联式。     

High-velocity fluidization of solid particles in a liquid-solid circulating fluidized bed system

Particulate and aggregative fluidizations in a liquid-solid circulating fluidized bed system are characterized by chaotic time series analysis of local voidage and heat transfer fluctuations in terms of the correlation dimension and Kolmogorov entropy. Both correlation dimension and Komogorov entropy of the voidate fluctuation are found to decrease with decreasing bed voidage in both fluidization regimes, suggesting the suppression of chaotic motion of individual particles due to high solid concentration. The correlation dimension of the heat transfer fluctation in the aggregative fluidization regime is higher than that in the particulate fluidization regime. This reflects the complex convective motion of liquid and solid phases induced by the formation of the liquid streaks and aggregates of particles.     

幂律流体在Kenics型静态混合器中流动特性分析

为了探究Kenics型静态混合器内扭旋叶片剪切作用对幂律流体流动的影响,利用旋转流变仪测量了浓度为0.5wt%, 0.7wt%, 0.9wt%的羧甲基纤维素(CMC)水溶液的流变参数,采用数值模拟与实验研究了扭旋叶片作用下幂律流体流动阻力和剪切稀化特性。对流场研究表明,扭旋叶片诱导产生了内流涡旋、绕流涡旋和近壁面涡旋,有效强化了静态混合器内流体流动的剪切作用。受多个纵向涡旋分布的影响,扭旋叶片局域流场中周向45°位置速度最高,周向30°位置涡量与剪切应力最高而黏度最低。径向0.4倍半径位置速度最高,0.7倍半径位置黏度最高。静态混合器有效提高了流体的二次流流动速度和剪切应力,降低了幂律流体的黏度和流动阻力系数。     

SK型静态混合器壁压脉动信号的多尺度多分形特性

为了探讨静态混合器内非线性、非均匀性和混沌特性机理,利用高速数据采集系统对SK型静态混合器管壁处脉动压力进行测量。结合小波变换模极大值理论,对采集的不同进口流量下壁压波动时间序列用Daubechies二阶小波提取1～7尺度下的特征信号,并分别对提取的信号进行R/S分析。通过对压力波动信号不同尺度下的细节信号与概貌信号研究,发现在不同尺度下其表现出不同的分形结构,且随着进口流量的增大,分形结构的变化趋势基本一致。此外,该系统不仅存在确定性非周期成分,而且不同尺度的旋涡之间的能量交换导致混沌的产生。各尺度信号的能量分布表明,压力波动信号主要体现了宏观尺度的旋涡级串的相互作用。     

CFD modelling of a liquid-solid fluidized bed

A multifluid Eulerian computational fluid dynamics (CFD) model with granular flow extension is used to simulate a liquid-solid fluidized bed. The numerical simulations are evaluated qualitatively by experimental data from the literature and quantitatively by comparison with new experimental data. The effects of mesh size, time step and convergence criteria are investigated. Varying the coefficient of restitution did not alter the results significantly. The Gidaspow drag relationship predicted a higher voidage than the Wen and Yu drag law. Two different liquid distributors (uniform and non-uniform) were simulated and compared, but a better representation of the geometry of the distributor plate did not greatly influence the results. Qualitatively, the simulations show trends similar to experimental trends reported by various authors. The predictions are also compared with new experimental results for 1.13 mm glass spheres at a wide variety of superficial liquid velocities (0.0085-0.110 m/s) and two different temperatures (12 and ) significantly affecting the liquid viscosity. The CFD model predictions are within 5% of the steady-state experimental data and show the correct trend with variation in viscosity.     

SK型静态混合器切割区内速度混沌特性

为揭示SK型静态混合器内非稳态流动特性,利用激光多普勒粒子分析仪对直径为0.04m、长径比为1.25的SK型静态混合器的切割区瞬时流场进行测量。采用功率谱和最大Lyapunov指数识别混合器内瞬时速度时间序列的混沌特性,利用湍流高阶矩参数分析混沌运动的统计特征。实验结果表明:SK型静态混合器切割区速度波动时间序列具有混沌特性;功率谱函数随频率的增加呈幂函数衰减,瞬时速度脉动主要能量集中在31.25Hz以下;湍流高阶矩分布揭示了切割区内的速度脉动存在非线性拟序结构,混沌运动的概率密度函数偏离高斯分布。