竖直矩形窄通道内流动沸腾局部换热特性实验研究

为了明确竖直矩形窄通道内各阶段流动沸腾的换热特性,优化换热器性能,以去离子水为工质,对尺寸为720 mm×250 mm×3.5 mm的单面电加热竖直矩形窄通道内的流动沸腾换热进行实验研究,分析了质流密度、进口温度、热流密度对流动沸腾局部换热特性的影响。并在已有流动沸腾传热关联式的基础上,对实验数据进行非线性回归分析,得到适用于实验工况下的新流动沸腾传热关联式。结果表明：质流密度增大对流动沸腾段换热特性有强化作用,对核态沸腾段换热特性有削弱作用;热流密度对核态沸腾影响剧烈,但对流动沸腾的影响不明显;入口温度越高,流体会越早进入过冷沸腾阶段,但对局部传热系数的影响不明显;新流动沸腾传热关联式与实验值的平均相对误差为23.87%,其中74.19%的预测值在±25%内,83.87%的预测值在±50%以内,能很好地预测本实验工况下矩形窄通道内流动沸腾的局部传热系数。     

矩形窄缝流道内过冷沸腾汽泡行为的可视化

采用高速摄像仪,对矩形窄缝流道内过冷沸腾时的汽泡行为进行了可视化实验研究.分析了工况参数对汽泡成核起始点及其脱离直径的影响.结果表明:高过冷沸腾时,窄缝流道内加热面上产生了沿近壁面滑移的汽泡,这种滑移汽泡对窄缝流道内的换热产生了积极的作用,而且汽泡的滑移现象与主流流体的温度有着密切的关系,分析了产生这种滑移现象的原因.     

微细通道CO_2流动沸腾换热临界热流密度研究

CO2在微细通道内流动沸腾换热过程所具有的临界热流密度(CHF)对于其换热系数有着重要影响。根据国内外现有发表的公开文献的实验数据分析了质量流量、饱和温度、管径等对临界热流密度的影响,并对理论模型与试验数据进行误差分析。发现Bowring预测关联式对小于3 mm管径内临界热流密度预测精度较高,在30%误差范围内可以达到70%预测精度,Wojtan预测关联式具有较小的平均绝对误差。提出了今后CO2在微细通道内沸腾换热CHF的研究方向。     

外加电场强化苯自然对流和沸腾换热的试验研究

对沉浸在非极性有机液体工质苯中的平板表面自然对流和沸腾换热的外加电场强化进行了试验，得出了自然对流和沸腾换热的换热系数、强化效果与电场电压、热流密度的关系。试验数据表明外加电场对平板表面苯的自然对流换热和沸腾换热都有一定的强化效果，但外加电场对平板表面苯自然对流换热的强化效果明显好于对沸腾换热的强化效果；且平板表面苯的自然对流换热的强化效果与试验所给定的热流密度无关，而外加电场对平板表面苯的沸腾换热的强化效果随热流密度的增大而减弱。     

水平微细管道内R717沸腾换热特性研究

搭建了氨(R717)沸腾换热测试台,对内径3 mm水平光管内R717的沸腾换热特性进行了测试,分析热流密度、干度、饱和温度及质量流率对沸腾换热及换热方式的影响。实验热流密度15～40 kW/m~2,质量流率40～160 kg/(m~2·s),饱和温度-5、0和5℃,干度0.1～0.9。结果表明:在氨制冷剂管内沸腾换热的过程中,质量流率过低和热流密度过高会导致干涸传热恶化,换热形式由核态沸腾换热向气态氨制冷剂强制对流换热转变,同时也影响干涸的起始干度;在干涸发生前,沸腾换热系数随着干度的增加而增大,逐渐达到峰值;在干涸发生后,传热恶化导致换热系数急剧降低;饱和温度升高会加快核态沸腾气泡生成速率,强化沸腾换热,但干涸的起始干度随着饱和温度升高而降低。     

微细圆管内CO2两相沸腾换热实验研究

本文对CO_2在水平微细管内流动沸腾特性进行实验研究。实验结果表明:热流密度增加对强化核态沸腾换热和高干度区域流型转变具有显著影响,随着热流密度的增加换热系数增加,对摩擦压降影响很小;质量流率对于换热系数的影响较小,但随着质量流率的增加摩擦压降大幅增加,质量流率的大小直接决定了换热过程所经历流态;饱和温度升高换热系数相应升高,摩擦压降减小,且对流态转变特性有重要影响。在同样工况下摩擦压降最大值先于换热系数最大值出现,理论分析采用的流态形式与实际CO_2管内流动流动沸腾换热流态基本一致。     

骨架发热多孔介质通道内单相流阻力与换热特性数值模拟

以Fluent 6.3为平台,采用局部非热平衡模型,对紊流及紊流过渡区范围内骨架发热多孔介质竖直通道内的非达西强制对流换热进行了数值模拟。采用三维N-S方程及标准k-ε湍流模型描述多孔介质内的流动,详细研究了孔隙有效雷诺数Re(400Re2000),表面热流密度q(q=5、30和90 kW/m2)和冷却剂入口温度Tin(Tin=20、50和80℃)的变化对多孔介质流道内流动阻力及换热特性的影响。结果表明:低热流密度下,表面热流密度的变化对流动阻力和换热系数的影响很小;小球直径对换热系数的影响显著,且随着雷诺数的增加而增加;换热系数随冷却剂入口温度的增加而减小。     

微通道内流动沸腾特性研究

对国内外微通道流动和换热的研究实验作了总结,阐述了影响微通道换热系数的因素,如热流密度、过热度和干度等.对去离子水在内径为0.65 mm、长为102 mm的圆形管道内流动沸腾换热进行了实验研究,得到了局部换热系数随干度的变化关系,进而根据换热系数的变化趋势讨论了饱和流动沸腾区微通道内主导的换热机制.结果表明:从换热系数随干度的变化关系很难判定主导的换热机制;将实验数据与已发表的预测关联式进行了比较,发现大多关联式都失效,说明基于常规理论的模型不再适用于微通道.     

水平窄空间沸腾传热的实验研究

通过对五种尺寸的窄空间试验元件分别以水和乙醇做工质进行实验。研究了窄空间间距、窄空间尺寸、不同工质及不同热流密度对窄空间沸腾性能的影响。结果表明：当窄空间尺寸与热流通等因素组合恰当时。其换热系数可比大空间池沸腾提高3～6倍；临界热流密度有所降低。     

R134a在水平高效强化蒸发管内流动沸腾传热特性的实验研究

本文阐述了新型替代工质HFC—134a在内螺旋微翅片强化蒸发管内水平流动沸腾换热实验研究。归纳总结了大量沸腾换热性能曲线，揭示了壁面温度沿轴向变化的规律以及沸腾换热系数与热流密度及质量流量等的因变关系，并获得了强化管的换热强化倍率。     

Experimental investigation of heat transfer enhancement using impingement of multiple water jets

The problem of cooling electronic components has become a subject of special interest in recent years due to the increasing capacity and rapidly decreasing size of electronic components. Direct contact cooling using multiple jet impingement is considered the most effective method. The heat transfer problem is complex and a better understanding of the jet impingement method is essential for the proper application of this method for electronic cooling. Investigations were carried out using an electrically heated test plate. Heat flux in the range of 25 to $200 \ \hbox{W/cm}^{2}$ , which is a typical requirement for cooling high power electronic components was dissipated using 0.5‐mm diameter water jets arranged in a 7×7 array with a pitch of 3 mm. Temperature difference between the test plate and water was within $30 \ ^{\circ}\hbox{C}$ . Tests were performed in the flow rate range of 22 to 40 ml/min, resulting in a Reynolds number range of 1100 to 1750. Results show a significant increase in the heat transfer coefficient or Nusselt number with an increase in heat flux. The effect of the flow rate or Reynolds number on the heat transfer coefficient is found to be negligible. © 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20291     

Augmentation of heat transfer through passive techniques

The thermal performance of energy preservation systems is greatly improved by increasing miniaturization and boosting. These are imaginative (or Promethean) techniques to enhance heat transfer. Enhancement methods of heat transfer draw great attention in front of the industrial sector because of their ability to provide energy savings and raise the economic efficiency of thermal systems. Three techniques these methods are categorized; those are active, passive, and compound. Different types of components are used in passive methods because of the transfer/working fluid flow path to the enhancement of the heat transfer rate. In this article, the subject of the review was the passive heat transfer enhancement methods including inserts (conical strips, winglets, twisted tapes, baffles), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), extended surfaces (fins) and nanofluids (mono and hybrid nanofluid). Recent passive heat transfer enhancement techniques are studied in this article as they are cost-effective and reliable, and also comparably passive methods do not need any extra power to promote the energy conversion systems' thermal efficiency than active methods. In the passive approaches, various components are applied to the heat transfer/working fluid flow path to improve the heat transfer rate. The passive heat transfer enhancement methods studied in this article include inserts (twisted tapes, conical strips, baffles, winglets), extended surfaces (fins), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), and nanofluids (mono and hybrid nanofluid). From the pioneers' research work, it is clear that a lower twist ratio and lower pitch, lesser winglet angles can provide more heat transfer rate and a little bit more friction factor. In the case of nanofluids, a little bit of pumping power is enhanced. Finally, heat transfer enhancement is compared with the thermal performance factor, which is more than unity.     

中餐炒菜灶的系统热效率分析

传统的鼓风式中餐炒菜灶热效率仅为20%左右,通过增加辐射壁,可强化传统炒菜灶的燃烧与换热过程,提高系统热效率。采用均匀搅拌反应器(PSR)模型,研究了炉内的燃烧与换热过程,建立了相应的传热模型,并对系统热效率进行了分析。研究发现改造后的新型中餐炒菜灶热效率有大幅度提高,具有显著的节能效果和应用前景。     

套管换热器对流换热的数值模拟研究

本文建立了一种复杂的数学模型用于预测套管式换热器内流体的流动及传热特性。数学模型包括计算流体力学模型和计算传热学模型。其中,计算传热学模型中的湍流扩散系数是利用温度方差t2和温度方差耗散率εt来求解,而不是利用通常采用的Pr数假设值或实验测定值来求解。为验证新建立模型预测结果的准确性,本文将数值模拟结果与文献中的实验结果进行了比较,结果吻合较好。     

LDV散热器传热特性的分析研究

散热器是发动机是重要部件总成。本文对上海汽车商用车技术中心LDV车用散热器的传热性能进行风洞试验,由实测试验数据,将管外横掠管簇的对流换热系数从传热系数中分离出来,整理成无量纲准则式,为散热器的优化设计提供参考依据。另外,对一些未做过性能试验的散热器的设计计算也能提供帮助。     

Inverse estimation of boundary conditions on radiant enclosures by temperature measurement on a solid object

In this paper, we present an inverse analysis to estimate the thermal boundary conditions over a two-dimensional radiant enclosure from the knowledge of the measured temperatures for some points on a solid object within the enclosure. The conduction heat transfer in the solid object and the radiative heat transfer between the surface elements of the enclosure are formulated by the finite volume method and the net radiative method, respectively. The resultant set of nonlinear equations is solved by the Newton's method. The inverse problem for estimation of boundary conditions over the radiant enclosure is solved by the conjugate gradient method.     

锥形内肋管传热与流阻性能的数值模拟

根据纵向涡强化传热技术提出了新型的强化换热管——锥形内肋管,运用数值模拟方法,研究了新型强化换热管结构参数锥底宽度a、导程P、肋深e和Re数对Nu、沿程阻力系数f及传热综合因子η的影响。结果表明：换热管内壁面边缘处产生了较多的微小涡流,有效破坏了流动边界层,强化了传热。在充分湍流的条件下,流体Re越小、e越小,其综合传热性能越强。当Re<15 000时,a对η的影响要大于P;在过渡点后, P对η影响较大。通过综合传热性能分析,给出了适合不同Re区间的锥形内肋优化参数。     

Application of Hermite wavelet method for heat transfer in a porous media

In this article, the flow and heat transfer for non-Newtonian viscoelastic fluid in an axisymmetric channel with a porous wall is investigated. Convective boundary conditions have been used in the problem formulation. We obtain coupled, highly nonlinear ordinary differential equations from the fundamental governing equations via appropriate similarity variables. The solution for velocity and temperature are computed by applying the Hermite wavelet method (HWM). The comparison between the results from the HWM, differential transform method, and numerical method are well in agreement which proves the capacity of HWM for solving such problems. The effects of Reynolds number and Prandtl number on the velocity and temperature are illustrated through graphs and tables for different values of an independent variable.     

Heat and fluid flow characteristics inside differentially heated square enclosures with single and multiple sliding walls

Fluid flow and heat transfer characteristics of differentially heated lid driven cavities are numerically modeled and analyzed in the present study. One‐, two‐, and four‐sided lid driven cavity configurations are considered with the vertical walls being maintained at different temperatures and the horizontal walls being thermally insulated. Eight different cavity configurations are considered depending on the direction of wall motion. The Prandtl number Pr is taken to be 0.7, the Grashof number is taken to be 10⁴, while two values for the Richardson number Ri are considered, 0.1 and 10. It is found that both the Richardson number and the cavity configuration affect the heat and fluid flow characteristics in the cavity. It is concluded that for Ri=0.1, a four‐sided driven cavity configuration with all walls rotating in the same direction would triple the value of the average Nusselt number at the cold wall when compared to a one‐sided driven cavity configuration. However, for Ri=10, the cavity configuration has minimal effect and all eight cases result in an average Nusselt number value at the cold wall ranging between 1.3 and 1.9. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/htj.20264     

Enhancement in Evaporative Effectiveness of an Evaporative Tubular Heat Dissipator Using Experimental Design Approach

An experimental investigation of evaporative effectiveness and mass transfer coefficient on a bundle of tubes of an evaporative tubular heat dissipator is presented. Based on the experiments, correlations of evaporative effectiveness and mass transfer coefficient are derived using multiple regression analysis. A statistical model is developed to correlate the operating variables using design of experiment approach by selecting central composite design of a response surface methodology. Results shown in this article indicate that as the cooling film flow rate increases, evaporative effectiveness and mass transfer coefficient increases provided that the air flow rate is constant which is flowing from underneath the tubes of the evaporative tubular heat dissipator. Derived correlations are helpful in improvement of the design of heat transfer devices and many other engineering applications. Consideration of relative humidity of upstreaming air as one of the operating variables leads to the contribution to heat and mass transfer study of evaporative tubular heat dissipators in the present investigation.