Fabrication of PLA/PEG/MWCNT electrospun nanofibrous scaffolds for anticancer drug delivery

In the present study, polylactic acid (PLA)/polyethylene glycol (PEG)/multiwalled carbon nanotube (MWCNT) electrospun nanofibrous scaffolds were prepared via electrospinning process and their applications for the anticancer drug delivery system were investigated. A response surface methodology based on Box–Behnken design (BBD) was used to evaluate the effect of key parameters of electrospinning process including solution concentration, feeding rate, tip–collector distance (TCD) and applied voltage on the morphology of PLA/PEG/MWCNT nanofibrous scaffolds. In optimum conditions (concentration of 8.15%, feeding rate of 0.2 mL/h, voltage of 18.50 kV and TCD of 13.0 cm), the minimum experimental fiber diameter was found to be 225 nm which was in good agreement with the predicted value by the BBD analysis (228 nm). In vitro drug release study of doxorubicin (DOX)‐loaded nanofibrous scaffolds, higher drug content induced an extended release of drug. Also, drug release rate was not dependent on drug/polymer ratio in different electrospun nanofibrous formulations. The equation of M_t = c₀ + kt^0.5was used to describe the kinetic data of DOX release from electrospun nanofibers. The cell viability of DOX‐loaded nanofibrous scaffolds was evaluated using 3‐(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide, a tetrazole assay on lung cancer A549 cell lines. We propose that DOX‐incorporated PLA/PEG/MWCNT nanofibrous scaffold could be used as a superior candidate for antitumor drug delivery. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41286.     

磁性Fe3O4纳米粒子用作靶向药物载体的制备及分析

Fe3O4 magnetic nanoparticles were prepared by the aqueous co-precipitation of FeCl3-6H2O and FeCl2-4H2O with addition of ammonium hydroxide. The conditions for the preparation of Fe3O4 magnetic nanoparticles were optimized, and Fe3O4 magnetic nanoparticles obtained were characterized systematically by means of transmission electron microscope （TEM）, dynamic laser scattering analyzer （DLS） and X-ray diffraction （XRD）. The results revealed that the magnetic nanoparticles were cubic shaped and dispersive, with narrow size distribution and average diameter of 11.4 nm. It was found that the homogeneous variation of pH value in the solution via the control on the dropping rate of aqueous ammonia played a critical role in size distribution. The magnetic response of the product in the magnetic field was also analyzed and evaluated carefully. A 32.6 mT magnetic field which is produced by four ferromagnets was found to be sufficient to excite the dipole moments of 0.05 g Fe3O4 powder 2 cm far away from the ferromagnets. In conclusion, the Fe3O4 magnetic nanoparticles with excellent properties were competent for the magnetic carders of targeted-drug in future application.     

Facile Synthesis of FeCo/Fe3O4 Nanocomposite with High Wave-Absorbing Properties

The FeCo/Fe₃O₄ nanocomposite was synthesized using the hydrothermal approach, in which the FeCo alloy and Fe₃O₄ are formed by one step. The structure of the FeCo/Fe₃O₄ nanocomposite was characterized by means of Scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray energy-dispersive spectrometer spectroscopy (EDX). They show that the mass ratio of FeCo/Fe₃O₄ strongly depends on the reaction temperature. Such various architectures follow a stepwise growth mechanism of the composites prepared in various reaction temperatures were also discussed. It indicates that this strategy is facile, effective and controllable for the synthesis of FeCo/Fe₃O₄ by the one-step method. Furthermore, the magnetic and wave-absorbing properties of the nanocomposites with various structures were investigated in detail. The results show that the FeCo/Fe₃O₄ with higher mass ratio has higher magnetic properties. Moreover, the FeCo/Fe₃O₄ nanocomposite shows high wave-absorbing properties (e.g., −37.9 dB), which are expected to apply in microwave absorbing materials.     

Electro-Magnetic Polyfuran/Fe3O4 Nanocomposite: Synthesis,Characterization, Antioxidant Activity,and Its Application as a Biosensor

Herein, the authors report the synthesis of electro-magnetic polyfuran/Fe₃O₄ nanocomposites using Fe₃O₄ magnetic nanoparticles of different content as nucleation sites via in situ chemical oxidation polymerization method. Surface, structural, morphological, thermal, electrical and magnetic properties of the nanocomposites were studied by FT-IR, UV-visible spectroscopies, XRD, FESEM, TGA, four probe, and VSM, respectively. The effect of Fe₃O₄ nanoparticles content on the electrical conductivity and magnetization of nanocomposites was studied. The obtained polyfuran and polyfuran/Fe₃O₄ nanocomposites were analyzed for their antioxidant activity using 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay. In addition, polyfuran/Fe₃O₄ nanocomposites have been investigated for application as electrochemical biosensor.     

Synthesis of magnetic Pb/Fe3O4/SiO2 and its catalytic activity for propylene carbonate synthesis via urea and 1,2-propylene glycol

To facilitate the recovery of Pb/SiO₂ catalyst, magnetic Pb/Fe₃O₄/SiO₂ samples were prepared separately by emulsification, sol-gel and incipient impregnation methods. The catalyst samples were characterized by means of X-ray diffraction and N₂ adsorption-desorption, and their catalytic activity was investigated in the reaction for synthesizing propylene carbonate from urea and 1,2-propylene glycol. When the gelatin was applied in the preparation of Fe₃O₄ at 60°C and the pH value was controlled at 4 in the preparation of Fe₃O₄/SiO₂, the Pb/Fe₃O₄/SiO₂ sample shows good catalytic activity and magnetism. Under the reaction conditions of a reaction temperature of 180°C, reaction time of 2 h, catalyst percentage of 1.7 wt-% and a molar ratio of urea to PG of 1:4, the yield of propylene carbonate attained was 87.7%.     

Sonochemical synthesis of magnetic core–shell Fe3O4@ZrO2 nanoparticles and their application to the highly effective immobilization of myoglobin for direct electrochemistry

In this study, bifunctional Fe₃O₄@ZrO₂ magnetic core–shell nanoparticles (NPs), synthesized by a simple and effective sonochemical approach, were attached to the surface of a magnetic glassy carbon electrode (MGCE) and successfully applied to the immobilization/adsorption of myoglobin (Mb) for constructing a novel biosensor platform. With the advantages of the magnetism and the excellent biocompatibility of the Fe₃O₄@ZrO₂ NPs, Mb could be easily immobilized on the surface of the electrode in the present of external magnetic field and well retained its bioactivity, hence dramatically facilitated direct electron transfer of Mb was demonstrated. The proposed Mb/Fe₃O₄@ZrO₂ biofilm electrode exhibited excellent electrocatalytic behaviors towards the reduction of H₂O₂ with a linear range from 0.64 μM to 148 μM. This presented system avoids the complex synthesis for protecting Fe₃O₄ NPs, supplies a simple, effective and inexpensive way to immobilize protein, and is promising for construction of third-generation biosensors and other bio-magnetic induction devices.     

Efficient solar photocatalyst based on cobalt oxide/iron oxide composite nanofibers for the detoxification of organic pollutants

A Co₃O₄/Fe₂O₃ composite nanofiber-based solar photocatalyst has been prepared, and its catalytic performance was evaluated by degrading acridine orange (AO) and brilliant cresyl blue (BCB) beneath solar light. The morphological and physiochemical structure of the synthesized solar photocatalyst was characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). FESEM indicates that the Co₃O₄/Fe₂O₃ composite has fiber-like nanostructures with an average diameter of approximately 20 nm. These nanofibers are made of aggregated nanoparticles having approximately 8.0 nm of average diameter. The optical properties were examined by UV-visible spectrophotometry, and the band gap of the solar photocatalyst was found to be 2.12 eV. The as-grown solar photocatalyst exhibited high catalytic degradation in a short time by applying to degrade AO and BCB. The pH had an effect on the catalytic performance of the as-grown solar photocatalyst, and it was found that the synthesized solar photocatalyst is more efficient at high pH. The kinetics study of both AO and BCB degradation indicates that the as-grown nanocatalyst would be a talented and efficient solar photocatalyst for the removal of hazardous and toxic organic materials.     

Electromagnetic properties of electrospun Fe3O4/carbon composite nanofibers

In order to develop multifunctional nanofibers, the electrical conductivity and magnetic properties of Fe₃O₄/carbon composite nanofibers have been examined. Polyacrylonitrile (PAN) is used as a matrix to produce magnetic composite nanofibers containing different amounts of magnetite (Fe₃O₄) nanoparticles. Electrospun composite nanofibers were thermally treated to produce electrically conductive and magnetically permeable composite carbon nanofibers. The composite nanofibers were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffractometry (XRD), Raman spectroscopy, four-point probe and Superconducting Quantum Interference Device (SQUID). Uniform nanofibers were obtained with successful transferring of magnetic properties of Fe₃O₄ into the as-spun composite nanofibers. The electromagnetic properties were tuned by adjusting the amount of Fe₃O₄ in the matrix and carbonization process. The electrical conductivity, magnetic moment and also magnetic hysteresis rise up by adding Fe₃O₄ and increasing carbonization temperature. The high surface area provided by the ultrafine fibrous structures, the flexibility and tuneable electromagnetic properties are expected to enable the expansion of the design options for a wide rage of electronic devices.     

Reduction and oxidation properties of Fe2O3/ZrO2 oxygen carrier for hydrogen production

Fe₂O₃ is a promising oxygen carrier for hydrogen production in the chemical-looping process. A set of kinetic studies on reduction with CH₄, CO and H₂ respectively, oxidation with water and oxygen containing Ar for chemical-looping hydrogen production was conducted. Fe₂O₃ (20 wt.%)/ZrO₂ was prepared by a co-precipitation method. The main variables in the TGA (thermogravimetric analyzer) experiment were temperatures and gas concentrations. The reaction kinetics parameters were estimated based on the experimental data. In the reduction by CH₄, CO and H₂, the reaction rate changed near FeO. Changes in the reaction rate due to phase transformation were observed at low temperature and low gas concentration during the reduction by CH₄, but the phenomenon was not remarkable for the reduction by CO and H₂. The reduction rate achieved using CO and H₂ was relatively faster than achieved using CH₄. The Hancock and Sharp method of comparing the kinetics of isothermal solid-state reactions was applied. A phase boundary controlled model (contacting sphere) was applied to the reduction of Fe₂O₃ to FeO by CH₄, and a different phase boundary controlled model (contacting infinite slab) was fit well to the reduction of FeO to Fe by CH₄. The reduction of Fe₂O₃ to Fe by CO and H₂ can be described by the former phase boundary controlled model (contacting sphere). This phase boundary controlled model (contacting sphere) also fit well for the oxidation of Fe to Fe₃O₄ by water and FeO to Fe₂O₃ by oxygen containing Ar. These kinetics data could be used to design chemical-looping hydrogen production systems.     

Crystallization behavior of polylactide matrix under the influence of nano‐magnetite

Iron oxide nanoparticle (Fe₃O₄) has gained remarkable research interest for various applications, from environmental to biological, because of its superparamagnetic properties and good biocompatibility. In this work, the nucleation effect of Fe₃O₄ in a polylactide (PLA) matrix under an influence of an alternating magnetic field was studied. The nanocomposite films that is, containing different concentrations of Fe₃O₄ (~8 nm) which were uniformly dispersed in the PLA matrix, were prepared via a solution casting method. The amplitude and frequency of the magnetic field impose great effects on the morphology and nucleation rate of PLA crystallization. Thermogravimetric analysis was used to study the thermal stability of Fe₃O₄/PLA and it showed that the thermal stability of Fe₃O₄/PLA was affected by the Fe₃O₄ content. Fourier transform infrared spectroscopy and X‐ray diffractometry indicated that Fe₃O₄ shows impeding effect to the crystallization of PLA. Based on the differential scanning calorimetry results, composite with 1% of Fe₃O₄ content could promote the crystallization of PLA but it would become an obstacle when 3% of Fe₃O₄ was added. The result of polarized optical microscopy also showed a good agreement that the incorporation of Fe₃O₄ could act as an effective nucleation regent to the composite film. POLYM. ENG. SCI., 59:608–615, 2019. © 2018 Society of Plastics Engineers     

Room temperature magnetoelectric coupling study in multiferroic Bi4NdTi3Fe0.7Ni0.3O15 prepared by a multicalcination procedure

Single-phase Bi₄NdTi₃Fe_0.7Ni_0.3O₁₅ polycrystalline samples were synthesized following a multicalcination procedure. The sample exhibited multiferroic property at room temperature, which was demonstrated by the ferroelectric (2P_r=8.52 μC/cm², 2E_c=89 kV/cm at applied electric field 110 kV/cm) and magnetic (2M_r=388 m emu/g, 2H_c=689 Oe at applied magnetic field 1.04 T) hysteresis loops. More importantly, magnetoelectric coupling effect is observed from measurements of electrical properties not only under small but also under large electric signal when an external magnetic field is applied. The present results suggest a new candidate for a room temperature multiferroic material with magnetoelectric coupling effect.     

Retention of Pb(II) by a Low-Cost Magnetic Composite Prepared by Environmentally-Friendly Plasma Technique

A low-cost magnetic composite (gelatin/Fe₃O₄) is prepared by Fe₃O₄ nanoparticles treated with gelatin using an environmentally-friendly plasma technique, and is applied for the removal of toxic Pb(II) ions from aqueous solutions. Not only that it originates from cheap and abundant raw materials, the gelatin/Fe₃O₄ composite also has advantages in convenient magnetic separation from aqueous solution, which can hopefully reduce water treatment expenses. The batch experimenta results indicate that the maximum adsorption capacity (q_max) of Pb(II) on this gelatin/Fe₃O₄ composite is ～115 mg/g, higher than most of the other bare and modified magnetic materials, which is considered to be attributed to the strong interaction between Pb(II) and the abundant functional groups introduced by gelatin. When exposed to acidic solutions, the dissolution of the gelatin/Fe₃O₄ nanoparticles is minimal due to the protective character of the grafted gelatin layer on the Fe₃O₄ nanoparticles. The utilization of the plasma technique in the synthesis of magnetic composite agrees well with the tenet of green chemistry. It is promising that this gelatin/Fe₃O₄ composite would become an efficient and economic material for heavy metal ion removal in the practical environmental remediation.     

Influence of Fe3O4 nanoparticles decoration on dye adsorption and magnetic separation properties of Fe3O4/rGO nanocomposites

Magnetite (Fe₃O₄) nanoparticles were prepared by solvothermal method and its composites with reduced graphene oxide namely FG1, FG2, and FG3 (changing magnetite precursor loading 0.1, 0.5, and 1 respectively) were used as adsorbents for the removal of methyl violet (MV) dye. The structural and morphological results confirm that rGO sheets were decorated with Fe₃O₄ and it ensures the variation of active sites toward dye removal property. The maximum adsorption capacity obtained for FG2 was 196 mg/g. The adsorption isotherms and kinetics better fit Langmuir and pseudo-second-order kinetic model for FG1 and FG2. Increasing of Fe₃O₄ loading on rGO reduces the dye adsorption sites and too low Fe₃O₄ loading affects the magnetic separation. The optimal loading of Fe₃O₄ on rGO is important parameter for the adsorption process and fast separation of adsorbent.     

聚乙二醇/聚乙烯吡咯烷酮修饰的纳米Fe3O4粒子的制备与表征

为了获得能够在水中稳定分散,具有广泛应用前景的磁性纳米粒子,以不同分子量的聚乙烯吡咯烷酮(PVP)作为修饰剂,在聚乙二醇(PEG)中高温热分解乙酰丙酮铁(Fe(acac)₃)制备了纳米Fe₃O₄粒子。采用X射线粉末衍射仪(XRD)、透射电镜(TEM)、高分辨透射电镜(HRTEM)、超导量子干涉仪(SQUID)、热重分析仪(TGA)、傅里叶变换红外光谱仪(FT-IR)、纳米粒度与zeta电位分析仪对样品进行了表征,并对样品在生理盐水和生理缓冲液中的稳定性进行了研究,结果表明:制备的纳米Fe₃O₄粒子具有高的结晶度以及单分散性,在300 K下,具有超顺磁性和较高的饱和磁化强度;PEG和PVP共同修饰于纳米Fe₃O₄粒子表面,为纳米Fe₃O₄粒子提供了良好的水分散性;制备的纳米Fe₃O₄粒子在生理盐水和多种生理缓冲液中能够高度溶解并稳定地分散。水中的纳米Fe₃O₄粒子表面呈电中性,表面修饰层的空间位阻效应是所制备的纳米粒子在水溶液中高分散的原因。     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Mn2O3/TiO2 nanofibers with broad-spectrum antibiotics effect and photocatalytic activity for preliminary stage of water desalination

Composite nanofibers consisting of Mn₂O₃ and TiO₂ were prepared by the electrospinning process, and tested as Gram-class-independent antibacterial agent and photocatalyst for organic pollutants degradation. Initially, electrospinning of a sol–gel consisting of titanium isopropoxide, manganese acetate tetrahydrate and poly(vinyl pyrrolidone) was used to produce hybrid polymeric nanofibers. Calcination of the obtained nanofibers in air at 650 °C led to produce good morphology Mn₂O₃/TiO₂ nanofibers. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to characterize the as-spun nanofibers and the calcined product. X-ray powder diffractometry (XRD) analysis was also used to characterize the chemical composition and the crystallographic structure of the sintered nanofibers. The antibacterial activity of Mn₂O₃/TiO₂ nanofibers against Gram negative and Gram positive bacteria was investigated by calculating the minimum inhibitory concentration after treatment with the nanofibers. Investigations revealed that the lowest concentration of Mn₂O₃/TiO₂ nanofibers solution inhibiting the growth of Staphylococcus aureus ATCC 29231 and Escherichia coli ATCC 52922 strains is 0.4 and 0.8 μg/ml, respectively. Incorporation of Mn₂O₃ significantly improved the photodegradation of methylene blue (MB) dye under the visible light irradiation due to enhancing rutile phase formation in the TiO₂ nanofibers matrix.     

Synthesis of Fe2O3 nanoparticles for nitrogen dioxide gas sensing applications

Iron (III) oxide, Fe₂O₃, nanoparticles of approximately 40 nm diameter were synthesized by sol–gel method and their nitrogen dioxide adsorption and desorption kinetics were investigated by custom fabricated gas sensor unit. The morphology and crystal structure of Fe₂O₃ nanoparticles were studied by scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) respectively. The roughness of film surface was investigated by atomic force microscopy (AFM). Relative sensitivity of Fe₂O₃ nanoparticles for NO₂ sensor was determined by electrical resistance measurements. Our reproducible experimental results show that Fe₂O₃ nanoparticles have a great potential for nitrogen dioxide sensing applications operating at a temperature of 200 °C.     

Functionalized magnetic core-shell Fe3O4@SiO2 nanoparticles as selectivity-enhanced chemosensor for Hg(II)

A colorimetric and ‘‘turn-on” fluorescent chemosensor Rho-Fe₃O₄@SiO₂ for Hg²⁺ in which N-(rhodamine-6G)lactam-ethylenediamine (Rho-en) is conjugated with the magnetic core-shell Fe₃O₄@SiO₂ NPs has been strategically designed and synthesized. The final product was characterized by X-ray power diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectra (FTIR) and UV-visible absorption and fluorescence emission. Fluorescence and UV-visible spectra results showed that the resultant multifunctional nanoparticles Rho-Fe₃O₄@SiO₂ exhibited selective ‘turn-on’ type fluorescent enhancements and distinct color changes with Hg²⁺. The selectivity of the Rho-Fe₃O₄@SiO₂ for Hg(II) ion is better than that of the Rho-en in the same conditions. In addition, the presence of magnetic Fe₃O₄ nanoparticles in the sensor Rho-Fe₃O₄@SiO₂ NPs would also facilitate the magnetic separation of the Hg(II)-Rho-Fe₃O₄@SiO₂ from the solution.     

A novel method for the synthesis of Fe3O4 nanoparticles/CdS nanowires heterostructure nanocomposite and uses in photodegradation of methylene blue

We report here a simple, efficient, practical, and novel method for the preparation of Fe₃O₄ nanoparticles (NPs)/CdS nanowires. The CdS nanowire/Fe₃O₄ NP reported here was characterized by transmission electron microscopy (TEM), X-ray Diffraction (XRD), vibrating sample magnetometer (VSM), and energy-dispersive X-ray. Cadmium diethyl dithiophosphate has been used as a 3 in 1 precursor (cadmium, sulfur, and ligand source) for the synthesis of high-quality one-dimensional Fe₃O₄ NPs/CdS nanowires using a simple hydrothermal method in the presence of Fe₃O₄ NPs in water. Photocatalytic activity studies show that the nanocomposite has good photocatalytic activity toward the photodegradation of methylene blue in an aqueous solution.     

Synthesis of a TiO2 ceramic membrane containing SrCo0.8Fe0.2O3 by the sol-gel method with a wet impregnation process for O2 and N2 permeation

A SrCo_0.8Fe_0.2O₃ impregnated TiO₂ membrane (TiO₂-SrCo_0.8Fe_0.2O₃ membrane) was successfully prepared using a sol-gel method in combination with a wet impregnation process. The membrane was subjected to a single gas permeance test using oxygen (O₂) and nitrogen (N₂). The TiO₂ membrane was immersed in the SrCo_0.8Fe_0.2O₃ solution, dried and then calcined to affix SrCo_0.8Fe_0.2O₃ into the membrane. The effect of the acid/alkoxide (H⁺/Ti⁴⁺) molar ratio of the TiO₂ sol on the TiO₂ phase transformation was investigated. The optimal molar ratio was found to be 0.5, which resulted in nanoparticles with a mean size of 5.30 nm after calcination at 400 °C. The effect of calcination temperature on the phase transformation of TiO₂ and SrCo_0.8Fe_0.2O₃ was investigated by varying the calcination temperature from 300 to 500 °C. X-ray diffraction spectroscopy (XRD) and Fourier transform infrared (FTIR) analysis confirmed that a calcination temperature of 400 °C was preferable for preparing a TiO₂-SrCo_0.8Fe_0.2O₃ membrane with fully crystallized anatase and SrCo_0.8Fe_0.2O₃ phases. The results also showed that polyvinyl alcohol (PVA) and hydroxypropyl cellulose (HPC) were completely removed. Field emission scanning electron microscopy (FESEM) analysis results showed that a crack-free and relatively dense TiO₂ membrane (∼0.75 μm thickness) was created with a multiple dip-coating process and calcination at 400 °C. The gas permeation results show that the TiO₂ and TiO₂-SrCo_0.8Fe_0.2O₃ membranes exhibited high permeances. The TiO₂-SrCo_0.8Fe_0.2O₃ membrane developed provided greater O₂/N₂ selectivity compared to the TiO₂ membrane alone.