A wideband 0.13 μm CMOS LC-VCO for IMT-advanced and UWB applications

This paper presents an LC voltage controlled oscillator(VCO) in a dual-band frequency synthesizer for IMT-advanced and UWB applications.The switched current source,cross-coupled pair and noise filtering technique are adopted in this VCO design to improve the performance of the phase noise,power consumption,voltage amplitude,and tuning range.In order to achieve a wide tuning range,a reconfigurable LC tank with 4 bits switch control is adopted in the core circuit design.The size of the entire chip with pad is 1.11 0.98 mm2.The test results show that the current dissipation of the VCO at UWB and IMT-Advanced band is 3 mA and 4.5 mA in a 1.2 V supply.The tuning range of the designed VCO is 3.86-5.28 GHz and 3.14-3.88 GHz.The phase-noise at 1 MHz frequency offset from a 3.5 GHz and 4.2 GHz carrier is-123 dBc/Hz and-119 dBc/Hz,respectively.     

A 0.8 μm BiCMOS Gate Driver for IGBT Power Switch

This paper discusses the design and implementation of a monolithic gate driver for an Insulated Gate Bipolar Transistor (IGBT). The objective is to implement a high voltage (25 V) monolithic gate driver with a novel protection circuit in a conventional low-voltage (5 V) high-density (0.8 m) BiCMOS process. Extended drain MOS-FETs are used to implement the high-voltage capability in this design.     

A fully integrated UHF RFID reader SoC for handheld applications in the 0.18 μm CMOS process

A low cost fully integrated single-chip UHF radio frequency identification(RFID) reader SoC for short distance handheld applications is presented.The SoC integrates all building blocks—including an RF transceiver,a PLL frequency synthesizer,a digital baseband and an MCU—in a 0.18μm CMOS process.A high-linearity RX frontend is designed to handle the large self-interferer.A class-E power amplifier with high power efficiency is also integrated to fulfill the function of a UHF passive RFID reader.The measure...     

A CMOS micro power switched-capacitor DC–DC step-up converter for indoor light energy harvesting applications

This paper presents a micro power light energy harvesting system for indoor environments. Light energy is collected by amorphous silicon photovoltaic (a-Si:H PV) cells, processed by a switched capacitor (SC) voltage doubler circuit with maximum power point tracking (MPPT), and finally stored in a large capacitor. The MPPT fractional open circuit voltage (V_OC) technique is implemented by an asynchronous state machine (ASM) that creates and dynamically adjusts the clock frequency of the step-up SC circuit, matching the input impedance of the SC circuit to the maximum power point condition of the PV cells. The ASM has a separate local power supply to make it robust against load variations. In order to reduce the area occupied by the SC circuit, while maintaining an acceptable efficiency value, the SC circuit uses MOSFET capacitors with a charge sharing scheme for the bottom plate parasitic capacitors. The circuit occupies an area of 0.31 mm² in a 130 nm CMOS technology. The system was designed in order to work under realistic indoor light intensities. Experimental results show that the proposed system, using PV cells with an area of 14 cm², is capable of starting-up from a 0 V condition, with an irradiance of only 0.32 W/m². After starting-up, the system requires an irradiance of only 0.18 W/m² (18 μW/cm²) to remain operating. The ASM circuit can operate correctly using a local power supply voltage of 453 mV, dissipating only 0.085 μW. These values are, to the best of the authors’ knowledge, the lowest reported in the literature. The maximum efficiency of the SC converter is 70.3 % for an input power of 48 μW, which is comparable with reported values from circuits operating at similar power levels.     

A 0.18 μm CMOS fluorescent detector system for bio-sensing application

A CMOS fluorescent detector system for biological experiment is presented. This system integrates a CMOS compatible photodiode, a capacitive trans-impedance amplifier (CTIA), and a 12 bit pipelined analog-to-digital converter (ADC), and is implemented in a 0.18 μm standard CMOS process. Some special techniques, such as a "contact imaging" detecting method, pseudo-differential architecture, dummy photodiodes, and a T-type reset switch, are adopted to achieve low-level sensing application. Experiment results show that the Nwell/Psub photodi-ode with CTIA pixel achieves a sensitivity of 0.1 A/W at 515 nm and a dark current of 300 fA with 300 mV reverse biased voltage. The maximum differential and integral nonlinearity of the designed ADC are 0.8 LSB and 3 LSB, respectively. With an integrating time of 50 ms, this system is sensitive to the fluorescence emitted by the fluorescein solution with concentration as low as 20 ng/mL and can generate 7 fA photocurrent. This chip occupies 3 mm2 and consumes 37 mW.     

A 0.18μm CMOS inductorless complementary-noise-canceling-LNA for TV tuner applications

This paper presents an inductorless complementary-noise-canceling LNA(CNCLNA) for TV tuners.The CNCLNA exploits single-to-differential topology,which consists of a common gate stage and a common source stage. The complementary topology can save power and improve the noise figure.Linearity is also enhanced by employing a multiple gated transistors technique.The chip is implemented in SMIC 0.18μm CMOS technology.Measurement shows that the proposed CNCLNA achieves 13.5-16 dB voltage gain from 50 to 860 MHz,...     

A 3.1-4.8 GHz transmitter with a high frequency divider in 0.18 μm CMOS for OFDM-UWB

A fully integrated low power RF transmitter for a WiMedia 3.1-4.8 GHz multiband orthogonal frequency division multiplexing ultra-wideband system is presented. With a separate transconductance stage, the quadrature up-conversion modulator achieves high linearity with low supply voltage. The co-design of different resonant frequencies of the modulator and the differential to single (D2S) converter ensures in-band gain flatness. By means of a series inductor peaking technique, the D2S converter obtains 9 dB more gain without extra power consumption. A divided-by-2 divider is used for carrier signal generation. The measurement results show an output power between -10.7 and -3.1 dBm with 7.6 dB control range, an OIP3 up to 12 dBm, a sideband rejection of 35 dBc and a carrier rejection of 30 dBc. The ESD protected chip is fabricated in the Jazz 0.18/zm RF CMOS process with an area of 1.74 mm~2 and only consumes 32 mA current (at 1.8 V) including the test associated parts.     

0.8 μm PDSOI CMOS器件和环振电路研究

研究了0.8μm部分耗尽绝缘体上硅(PDSOI)CMOS器件和电路,开发出成套的0.8μmPDSOI CMOS工艺.经过工艺投片,获得了性能良好的器件和电路.其中,当工作电压为5 V时,基于浮体SOI CMOS技术的0.8μm 101级环振单级延时为49.5 ps;基于H型栅体引出SOI CMOS技术的0.8μm 101级环振单级延时为158 ps.同时,对PDSOI CMOS器件的特性,如浮体效应、背栅特性、反常亚阈值斜率、击穿特性和输出电导变化等进行了讨论.     

A 0.13μm CMOS △∑ fractional-N frequency synthesizer for WLAN transceivers

A fractional-N frequency synthesizer fabricated in a 0.13 μm CMOS technology is presented for the application of IEEE 802.11 b/g wireless local area network (WLAN) transceivers.A monolithic LC voltage controlled oscillator (VCO) is implemented with an on-chip symmetric inductor.The fractional-N frequency divider consists of a pulse swallow frequency divider and a 3rd-order multistage noise shaping (MASH) △ ∑ modulator with noise-shaped dithering techniques.Measurement results show that in all channels,phase noise of the synthesizer achieves -93 dBc/Hz and -118 dBc/Hz in band and out of band respectively with a phase-frequency detector (PFD) frequency of 20 MHz and a loop bandwidth of 100 kHz.The integrated RMS phase error is no more than 0.8°.The proposed synthesizer consumes 8.4 mW from a 1.2 V supply and occupies an area of 0.86 mm2.     

A 0.13μm CMOS Δ ∑ fractional-N frequency synthesizer for WLAN transceivers

A fractional-N frequency synthesizer fabricated in a 0.13μm CMOS technology is presented for the application of IEEE 802.11 b/g wireless local area network(WLAN) transceivers.A monolithic LC voltage controlled oscillator(VCO) is implemented with an on-chip symmetric inductor.The fractional-TV frequency divider consists of a pulse swallow frequency divider and a 3rd-order multistage noise shaping(MASH)△Σmodulator with noise-shaped dithering techniques.Measurement results show that in all channels,phase noise of the synthesizer achieves -93 dBc/Hz and -118 dBc/Hz in band and out of band respectively with a phase-frequency detector (PFD) frequency of 20 MHz and a loop bandwidth of 100 kHz.The integrated RMS phase error is no more than 0.8°.The proposed synthesizer consumes 8.4 mW from a 1.2 V supply and occupies an area of 0.86 mm~2.     

A wideband current-commutating passive mixer for multi-standard receivers in a 0.18 μm CMOS

This paper reports a wideband passive mixer for direct conversion multi-standard receivers.A brief comparison between current-commutating passive mixers and active mixers is presented.The effect of source and load impedance on the linearity of a mixer is analyzed.Specially,the impact of the input impedance of the transimpedance amplifier(TIA),which acts as the load impedance of a mixer,is investigated in detail.The analysis is verified by a passive mixer implemented with 0.18 m CMOS technology.The circuit is inductorless and can operate over a broad frequency range.On wafer measurements show that,with radio frequency(RF) ranges from 700 MHz to 2.3 GHz,the mixer achieves 21 dB of conversion voltage gain with a-1 dB intermediate frequency(IF) bandwidth of 10 MHz.The measured IIP3 is 9 dBm and the measured double-sideband noise figure(NF) is 10.6 dB at 10 MHz output.The chip occupies an area of 0.19 mm2 and drains a current of 5.5 mA from a 1.8 V supply.     

Atmosphere Transmission Performance for 0.4 μm～0.8 μm Ray Radiation in Middle Latitude of China

This paper researched on the atmospheric transmission performance of 0.4μm～0.8 μm ray radiation based on the characteristic of the middle latitude atmosphere in China. By analysis of the characteristic of the actual atmosphere, the absorption of molecular and the scattering of the steam and ozone, as well as the aerosol scattering(big granule scattering) are play a leading role to the 0. 4 μm～0.8μm ray radiation. Then a better atmospheric transmission formula in horizontal path has been deducted. The result of computer simulation indicates that this equation can best calculate the transmission performance of 0.4 μm～ 0.8 μm visible radiation in the middle latitude area of China. This computing result was applied to the nuclear explosion parameter detection system based on 0.4 μm～0.8μm visible radiation. Through nuclear explosion simulator to produce ray radiation, the tested result indicates that this method has the better measuring precision than the traditional method with the software of LOWTRAN. The calculation result of this formula not only can apply directly to each kind of optoelectronics detecting system, but also to the optical wireless communication system based on the 0.4μm～0.8μm ray radiation.     

CMOS CCII– based on modified dual output-OTA for high frequency applications

A negative CMOS second generation current conveyor (CMOS CCII–) based on modified dual output CMOS folded cascode operational transconductance amplifier (CMOS DO-OTA) is presented. The proposed folded cascode CMOS DO-OTA with attractive features for high frequency operation such as high output impedance, wide bandwidth, high slew rate, with low power consumption is used in the realisation. The proposed CMOS DO-OTA and CMOS CCII– with high performance parameters can be used in many high frequency applications. The proposed CMOS CCII– achieves 1.37 GHz (?3 dB BW), 1.8 ns settling time, 48 V/μs slew rate, and low power consumption around 3.25 mW for ±2.5 V supply. P-Spice simulation results are included for 0.5 μm MIETEC CMOS technology.     

A 1.0 V differential VCO in 0.13 μm CMOS technology

A differential complementary LC voltage controlled oscillator(VCO) with high Q on-chip inductor is presented.The parallel resonator of the VCO consists of inversion-mode MOS(I-MOS) capacitors and an on-chip inductor.The resonator Q factor is mainly limited by the on-chip inductor.It is optimized by designing a single turn inductor that has a simulated Q factor of about 35 at 6 GHz.The proposed VCO is implemented in the SMIC 0.13μm 1P8M MMRF CMOS process,and the chip area is 1.0×0.8 mm~2.The free-running frequency is from 5.73 to 6.35 GHz.When oscillating at 6.35 GHz,the current consumption is 2.55 mA from a supply voltage of 1.0 V and the measured phase noise at 1 MHz offset is -120.14 dBc/Hz.The figure of merit of the proposed VCO is -192.13 dBc/Hz.     

A Fully Integrated Class 1 Bluetooth 0.25 μm CMOS PA

A fully integrated 0.25 m CMOS bluetooth class 1 power amplifier is presented. On this chip all inductors and decoupling capacitors are situated on the silicon die. Due to the high level of integration, a cheap flip chip assembly method has been used. The chip delivers 138 mW (21.4 dBm) of output power with a power added efficiency of 25.8%. When the amplifier is tuned to its optimum frequency of 2.1 GHz, the output power increases to 184 mW and the power added efficiency increases to 29.5%. To compare the performance of this realisation with other recently published PA, a figure of merit for saturated (switched) power amplifiers is introduced.Koen Mertens was born in Antwerpen, Belgium in 1971. He received the M.Sc. degree in Electrical Engineering from the Katholieke Universiteit Leuven, Belgium in 1998. The subject of his M.Sc. thesis was the design of a 2.14 GHz BICMOS oscillator. The thesis was in cooperation with IMEC. Since 1998. He has been a research assistant at the ESAT-MICAS laboratories, where he is currently working towards a Ph.D. degree in CMOS RF Power Amplifiers. His research promotor is Prof. Michiel Steyaert.Michiel Steyaert Michel S.J. Steyaert was born in Aalst, Belgium, in 1959. He received the masters degree in electrical-mechanical engineering and the Ph.D. degree in electronics from the Katholieke Universiteit Leuven (K.U. Leuven), Heverlee, Belgium in 1983 and 1987, respectively.From 1983 to 1986 he obtained an IWNOL fellowship (Belgian National Fundation for Industrial Research) which allowed him to work as a Research Assistant at the Laboratory ESAT at K.U. Leuven. In 1987 he was responsible for several industrial projects in the field of analog micropower circuits at the Laboratory ESAT as an IWONL Project Researcher. In 1988 he was a Visiting Assistant Professor at the University of California, Los Angeles. In 1989 he was appointed by the National Fund of Scientific Research (Belgium) as Research Associate, in 1992 as a Senior Research Associate and in 1996 as a Research Director at the Laboratory ESAT, K.U. Leuven. Between 1989 and 1996 he was also a part-time Associate Professor. He is now a Full Professor at the K.U. Leuven. His current research interests are in high-performance and high-frequency analog integrated circuits for telecommunication systems and analog signal processing.Prof. Steyaert received the 1990 European Solid-State Circuits Conference Best Paper Award, the 1995 and 1997 ISSCC Evening Session Award, the 1999 IEEE Circuit and Systems Society Guillemin-Cauer Award and the 1991 NFWO Alcatel-Bell-Telephone award for innovative work in integrated circuits for telecommunications.     

A wideband on-chip millimeter-wave patch antenna in 0.18 μm CMOS

A wideband on-chip millimeter-wave patch antenna in 0.18 μm CMOS with a low-resistivity(10Ω·cm) silicon substrate is presented.The wideband is achieved by reducing the Q factor and exciting the high-order radiation modes with size optimization.The antenna uses an on-chip top layer metal as the patch and a probe station as the ground plane.The on-chip ground plane is connected to the probe station using the inner connection structure of the probe station for better performance.The simulated S11 is less than –10 dB over 46–95 GHz,which is well matched with the measured results over the available 40–67 GHz frequency range from our measurement equipment.A maximum gain of –5.55 dBi with 4% radiation efficiency at a 60 GHz point is also achieved based on Ansoft HFSS simulation.Compared with the current state-of-the-art devices,the presented antenna achieves a wider bandwidth and could be used in wideband millimeter-wave communication and image applications.     

0.6 μm CMOS分布式放大器设计

采用了国内0.6μm标准CMOS工艺设计实现了一种单片集成的分布式放大器。放大器采用四级级联结构,单元电路采用管联(cascode)结构以提高隔离度。在输入输出端50Ω匹配情况下,测试得到的频带宽度为0.1~4.0 GHz,增益为5.0±1.0 dB,输入输出的回波损耗分别小于-10 dB和-7 dB。在5 V供电下功耗约为110 mW。     

A 0.18 μm CMOS ring VCO for clock and data recovery applications

In this paper, a 3.125 GHz four stage voltage controlled ring oscillator is presented. The oscillator has been designed in a 0.18 μm CMOS process with a 1.8 V supply. Behavioral simulations predict an 18% tuning range for the oscillator, with −91 dBc/Hz phase noise at 1 MHz offset. Its power consumption has been simulated to be as low as 15.3 mW and the variation of its DC level of oscillation is 20 mV, which corresponds to 1.3% of its mean value. While consuming less area than an LC VCO, the proposed oscillator design achieves a more stable and reliable operation point.