Dynamic mechanical behavior of LLDPE composites reinforced with kevlar fibers/short glass fibers

Kevlar fibers (DuPont) and glass fibers have been used to reinforce linear lowdensity polyethylene (LLDPE) by using an elastic melt extruder and the compression molding technique. The impact behavior of hybrid composites of different compositions is compared and has been explained on the basis of volume fraction of fibers. The addition of glass fibers decreases the Izod impact strength of LLDPE. The Izod impact strength of the composite increses when glass fibers are replaced by Kevlar fibers. Dynamic mechanical α‐relaxation is studied and the effect of variation of fiber composition on the relaxation is reported in the temperature range from −50°C to 150°C at 1 Hz frequency. The α‐relaxation shifts towards the higher temperature side on addition of fibers in LLDPE. The addition of fibers increases the storage modulus, E′, of LLDPE. The hybridization of Kevlar and glass fibers helps in desiging composites with a desirable combination of impact strength and modulus. At the low temperature region, E′ increases significantly with glass fibers as compared to that noted with the addition of Kevlar fibers. The α‐transition temperature of composites increases significantly with Kevlar fibers as compared to that observed with addition of glass fibers.     

Effects of kenaf contents and fiber orientation on physical,mechanical, and morphological properties of hybrid laminated composites for vehicle spall liners

The aim of this work is to study the effect of kenaf volume content and fiber orientation on tensile and flexural properties of kenaf/Kevlar hybrid composites. Hybrid composites were prepared by laminating aramid fabric (Kevlar 29) with kenaf in three orientations (woven, 0^o/90^o cross ply uni‐directional (UD), and non‐woven mat) with different kenaf fiber loadings from 15 to 20% and total fiber loading (Kenaf and Kevlar) of 27–49%. The void content varies between 11.5–37.7% to laminate with UD and non‐woven mat, respectively. The void content in a woven kenaf structure is 16.2%. Tensile and flexural properties of kenaf/Kevlar hybrid composites were evaluated. Results indicate that UD kenaf fibers reinforced composites display better tensile and flexural properties as compared to woven and non‐woven mat reinforced hybrid composites. It is also noticed that increasing volume fraction of kenaf fiber in hybrid composites reduces tensile and flexural properties. Tensile fracture of hybrid composites was morphologically analysed by scanning electron microscopy (SEM). SEM micrographs of Kevlar composite failed in two major modes; fiber fracture by the typical splitting process along with, extensive longitudinal matrix and interfacial shear fracture. UD kenaf structure observed a good interlayer bonding and low matrix cracking/debonding. Damage in composite with woven kenaf shows weak kenaf‐matrix bonding. Composite with kenaf mat contains the high void in laminates and poor interfacial bonding. These results motivate us to further study the potential of using kenaf in woven and UD structure in hybrid composites to improve the ballistic application, for example, vehicle spall‐liner. POLYM. COMPOS., 36:1469–1476, 2015. © 2014 Society of Plastics Engineers     

Performance enhancement of nylon/kevlar fiber composites through viscoelastically generated pre‐stress

Kevlar‐29 fibers have high strength and stiffness but nylon 6,6 fibers have greater ductility. Thus by commingling these fibers prior to molding in a resin, the resulting hybrid composite may be mechanically superior to the corresponding single fiber‐type composites. The contribution made by viscoelastically generated pre‐stress, via the commingled nylon fibers, should add further performance enhancement. This paper reports on an initial study into the Charpy impact toughness and flexural stiffness of hybrid (commingled) nylon/Kevlar fiber viscoelastically pre‐stressed composites at low fiber volume fractions. The main findings show that (i) hybrid composites (with no pre‐stress) absorb more impact energy than Kevlar fiber‐only composites; (ii) pre‐stress further increases impact energy absorption in the hybrid case by up to 33%; (iii) pre‐stress increases flexural modulus by ∼40% in the hybrid composites. These findings are discussed in relation to practical composite applications. POLYM. COMPOS., 35:931–938, 2014. © 2013 Society of Plastics Engineers     

Pultruded fiber reinforced thermoplastic poly(methyl methacrylate) composites. Part II: Mechanical and thermal properties

A novel process has been developed to manufacture poly(methyl methacrylate) (PMMA) pultruded parts. The mechanical and dynamic mechanical properties, environmental effects, postformability of pultruded composites and properties of various fiber (glass, carbon and Kevlar 49 aramid fiber) reinforced PMMA composites have been studied. Results show that the mechanical and thermal properties (i.e. tensile strength, flexural strength and modulus, impact strength and HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest impact strength and HDT, while carbon fiber/PMMA composites show the highest tensile strength, tensile and flexural modulus, and glass fiber/PMMA composites show the highest flexural strength. Experimental tensile strengths of all composites except carbon fiber/PMMA composites follow the rule of mixtures. The deviation of carbon fiber/PMMA composite is due to the fiber breakage during processing. Pultruded glass fiber reinforced PMMA composites exhibit good weather resistance. They can be postformed by thermoforming, and mechanical properties can be improved by postforming. The dynamic shear storage modulus (G′) of pultruded glass fiber reinforced PMMA composites increased with decreasing pulling rate, and G′ was higher than that of pultruded Nylon 6 and polyester composites.     

Mechanical properties of glass fiber/organic fiber mixed–mat reinforced thermoplastic composites

The purpose of this study is to investigate the influence of different types of fibers on the mechanical properties of hybrid composite materials. Long and short glass fibers (GF) and different types of organic fibers, viz. aramid fiber, DuPont Kevlar‐49 (KF), liquid crystalline polymer (LCP), and vinylon (VF) in hybrid composites, were used to reinforced the high density polyethylene (HDPE) matrix. The long fiber hybrid composites were prepared in a “fiber separating and flying machine,” while the short fiber hybrid composites were prepared in an “elastic extruder.” The total amount of fibers used in both long and short fiber hybrid composites was fixed at 20 vol%. The influence of fiber content, length, and mixing ratio on mechanical properties, such as tensile, bending, Izod and high rate impact strength, as well as viscoelastic propertics in the solid state, was studied. Fracture surfaces of the materials were also examined using a scanning electron microscopy.     

Injection‐molded short hemp fiber/glass fiber‐reinforced polypropylene hybrid composites—Mechanical,water absorption and thermal properties

Natural fiber‐based thermoplastic composites are generally lower in strength performance compared to thermoset composites. However, they have the advantage of design flexibility and recycling possibilities. Hybridization with small amounts of synthetic fibers makes these natural fiber composites more suitable for technical applications such as automotive interior parts. Hemp fiber is one of the important lignocellulosic bast fiber and has been used as reinforcement for industrial applications. This study focused on the performance of injection‐molded short hemp fiber and hemp/glass fiber hybrid polypropylene composites. Results showed that hybridization with glass fiber enhanced the performance properties. A value of 101 MPa for flexural strength and 5.5 GPa for the flexural modulus is achieved from a hybrid composite containing 25 wt % of hemp and 15 wt % of glass. Notched Izod impact strength of the hybrid composites exhibited great enhancement (34%). Analysis of fiber length distribution in the composite and fracture surface was performed to study the fiber breakage and fracture mechanism. Thermal properties and resistance to water absorption properties of the hemp fiber composites were improved by hybridization with glass fibers. Overall studies indicated that the short hemp/glass fiber hybrid polypropylene composites are promising candidates for structural applications where high stiffness and thermal resistance is required. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2432–2441, 2007     

Use of wood fibers in thermoplastics. VII. The effect of coupling agents in polyethylene–wood fiber composites

Linear low density polyethylene (LLDPE) was reinforced with different wood fibers, aspen chemithermomechanical pulp (bleached and unbleached), and other commerical wood pulps. Silane coupling agents A-172, A-174, A-1100, and polymethylene polyphenyl isocyanate were used to improve the bonding between the fiber and matrix. LLDPE filled with pretreated wood fiber produced a significant improvement in tensile strength and modulus. Comparison of tensile and impact properties of wood fiber composites with mica and glass fiber composites shows the potential advantage (in terms of material cost and specific properties) of wood fiber as a reinforcement.     

Use of grafted aspen fibers in thermoplastic composites: IV. Effect of extreme conditions on mechanical properties of polyethylene composites

Hardwood fibers of aspen in the form of chemithermo-mechanical pulp (CTMP) have been used as reinforcement in linear low density polyethylene (LLDPE). The effect of composite treatment (immersion in boiling water, heat exposure at 105°C for seven days or at a temperature of −40°C) on resulting mechanical properties were evaluated. The grafted aspen CTMP composites showed by far the best results with regard to secant modulus, tensile strength, energy, and strain when compared to those of wood flour, mica or glass–fiber filled LLDPE, as well as to virgin LLDPE. Finally, the dimensional stability of CTMP aspen-filled LLDPE composites immersed for four hours in boiling water was better than that of mica or glass–fiber filled LLDPE.     

Dynamic mechanical behavior of LCP fiber/glass fiber–reinforced LLDPE composites

Liquid crystalline polymer (LCP) fibers and glass fibers have been used to rein force linear low density polyethylene (LLDPE) by using an elastic melt extruder and the compression molding technique. The impact behavior of hybrid composites of different composition is compared and is explained on the basis of the volume frac tion of the fibers. Addition of glass fibers decreases the Izod impact strength LLDPE. The impact strength of the composites increases when glass fibers are placed by LCP fibers. Dynamic mechanical α and β relaxations are studied and effect of variation of fiber composition on these relaxations is reported in the tem perature range from −50 to 150°C at 1 Hz frequency, a relaxation shifts toward higher temperatures with addition of fibers in LLDPE. Addition of fibers increases the storage modulus of LLDPE.     

承载/声隐身混杂纤维复合材料的研究

通过试验获取了碳纤维(CF)、凯夫拉纤维(KF)、玻璃纤维(GF)、超高分子量聚乙烯纤维(UHMPEF)复合材料的力学性能和声学性能参数,在此基础上分别利用等效刚度法和传递矩阵法,对CF/UHMPEF、CF/KF、CF/GF混杂纤维复合材料的拉伸刚度、声反射系数和声透射系数进行计算。结果表明,材料的刚度和强度基本相同的条件下CF/UHMPEF复合材料声压反射系数最小,其次是CF/KF复合材料,再次是CF/GF复合材料。10kHz频率范围内3种混杂材料的声透射系数都达到95%以上。     

单向芳纶/玻璃纤维混杂复合材料板材拉伸性能研究

本文对单向芳纶/玻璃纤维复合材料进行制作,对其纵向拉伸强度、拉伸模量和弹性伸长进行实验分析。实验结果表明,单向混杂复合材料的拉伸断裂大多为多次性,界面数越多,一次性断裂的可能性越大。界面数为1的混杂纤维复合材料的芳纶纤维体积含量在对拉伸强度影响上的存在临界值,表现出明显的混杂效应。界面数大于1的混杂复合材料在芳纶纤维铺层数一定的情况下,界面数的多少不影响混杂复合材料拉伸强度和拉伸弹性模量的大小。界面数大于1比界面数为1的复合材料的拉伸强度和拉伸模量明显偏高。同时对不同制作条件下纯玻璃纤维单向复合材料的拉伸性能进行剖析。     

Dynamic mechanical properties of oil palm fiber/phenol formaldehyde and oil palm fiber/glass hybrid phenol formaldehyde composites

The dynamic mechanical properties of oil palm fiber reinforced phenol formaldehyde (PF) composites and oil palm/glass hybrid fiber reinforced PF composites were investigated as a function of fiber content and hybrid fiber ratio. The dynamic modulus of the neat PF sample decreases with decrease in frequency. Glass transition attributed with the α relaxation of the neat PF sample was observed around 140°C. Tanδ values and storage modulus show great enhancement upon fiber addition. The value increases with increase in fiber content. The loss modulus shows a reverse trend with increase in fiber loading. Incorporation of oil palm fiber shifts the glass transition towards lower temperature value. The glass transition temperature of the hybrid composites is lower than that of the unhybridized composites. The highest value of mechanical damping is observed in hybrid composites. Storage modulus of the hybrid composites is lower than unhybridized oil palm fiber/PF composite. A similar trend is observed for loss modulus. Activation energies for the relaxation processes in different composites were calculated. Activation energy is increased upon fibrous reinforcement. Complex modulus variations and phase behavior of the composites were studied from Cole‐Cole plots. Finally, master curves for the viscoelastic properties of the composites were constructed on the basis of time‐temperature superposition principle. POLYM. COMPOS., 26:388–400, 2005. © 2005 Society of Plastics Engineers     

Microstructure and fracture behavior of (co)injection‐molded polyamide 6 composites with short glass/carbon fiber hybrid reinforcement

The mechanical and fracture properties of injection molded short glass fiber)/short carbon fiber reinforced polyamide 6 (PA 6) hybrid composites were studied. The short fiber composites of PA 6 glass fiber, carbon fiber, and the hybrid blend were injection molded using a conventional machine whereas the two types of sandwich skin–core hybrids were coinjection molded. The fiber volume fraction for all formulations was fixed at 0.07. The overall composite density, volume, and weight fraction for each formulation was calculated after composite pyrolysis in a furnace at 600°C under nitrogen atmosphere. The tensile, flexural, and single‐edge notch‐bending tests were performed on all formulations. Microstructural characterizations involved the determination of thermal properties, skin–core thickness, and fiber length distributions. The carbon fiber/PA 6 (CF/PA 6) formulation exhibits the highest values for most tests. The sandwich skin‐core hybrid composites exhibit values lower than the CF/PA 6 and hybrid composite blends for the mechanical and fracture tests. The behaviors of all composite formulations are explained in terms of mechanical and fracture properties and its proportion to the composite strength, fiber orientation, interfacial bonding between fibers and matrix, nucleating ability of carbon fibers, and the effects of the skin and core structures. Failure mechanisms of both the matrix and the composites, assessed by fractographic studies in a scanning electron microscope, are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 957–967, 2005     

Recycled milk pouch and virgin LDPE‐LLDPE‐based jute fiber composites

The present investigation deals with the thermo‐mechanical recycling of post consumer milk pouches (LDPE‐LLDPE blend) and its use as jute fiber composite materials for engineering applications. The mechanical, thermal, morphological, and dynamic‐mechanical properties of recycled milk pouch‐based jute fiber composites with different fiber contents were evaluated and compared with those of the virgin LDPE‐LLDPE/jute fiber composites. Effect of artificial weathering on mechanical properties of different formulated composites was determined. The recycled polymer‐based jute fiber composites showed inferior mechanical properties as well as poor thermal stability compared to those observed for virgin polymer/jute fiber composites. However, the jute‐composites made with (50:50) recycled milk pouch‐virgin LDPE‐LLDPE blend as polymer matrix indicated significantly superior properties in comparison to the recycled milk pouch/jute composites. Overall mechanical performances of the recycled and virgin polymeric composites were correlated by scanning electron microscopy (SEM). The dynamic mechanical analysis showed that storage modulus values were lower for recycled LDPE‐LLDPE/jute composites compared to virgin LDPE‐LLDPE/jute composites throughout the entire temperature range, but an increase in the storage modulus was observed for recycled‐virgin LDPE‐LLDPE/jute composites. POLYM. COMPOS. 28:78–88, 2007. © 2007 Society of Plastics Engineers     

Effect of macromolecular coupling agent on the property of PP/GF composites

Silane‐grafted polypropylene manufactured by a reactive grafting process was used as the coupling agent in polypropylene/glass‐fiber composites to improve the interaction of the interfacial regions. Polypropylene reinforced with 30% by weight of short glass fibers was injection‐molded and the mechanical behaviors were investigated. The results indicate that the mechanical properties (tensile strength, tensile modulus, flexural strength, flexural modulus, and Izod impact strength) of the composite increased remarkably as compared with the noncoupled glass fiber/polypropylene. SEM of the fracture surfaces of the coupled composites shows a good adhesion at the fiber/matrix interface: The fibers are coated with matrix polymer, and a matrix transition region exists near the fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1537–1542, 1999     

Mechanical dispersion of crosslinked polymers reinforced with randomly distributed short fiber

The dynamic viscoelastic properties of composites reinforced with randomly distributed short glass and carbon fibers were studied in relation to the dependence on the fiber length, the mixing ratio of glass fibers of different length, and the kind of polymer matrix. Although the composite reinforced with glass fiber of 0.05 mm in length shows only one dispersion (α) corresponding to the primary transition of polymer matrix, those reinforced with 3- and 10-mm glass fibers, and those reinforced with the mixture of 10- and 0.05-mm glass fibers are characterized by two additional dispersions (α′ and α″) which appear on the lower frequency side or higher temperature side of the α-dispersion. The composite reinforced with 3-mm carbon fiber does not show the additional dispersions. The α′- and α″-dispersions appear irrespective of the kind of matrix polymer.     

Pultruded fiber-reinforced poly(methyl methacrylate) composites. II. Static and dynamic mechanical properties,environmental effect,and postformability

This paper presents a novel process developed to manufacture poly(methyl methacrylate) (PMMA) pultruded composite. The mechanical, thermal, and dynamic mechanical properties, environmental effect, postformability of various fiber (glass, carbon, and Kevlar 49 aramid fiber) reinforced pultruded PMMA composites have been studied. Results show mechanical properties (i.e., tensile strength, specific tensile strength, tensile modulus, and specific flexural strength) and thermal properties (HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest specific tensile strength and HDT, carbon fiber/PMMA composites show the highest tensile strength and tensile modulus, and glass fiber/PMMA composites show the highest specific flexural strength. Pultruded glass-fiber-reinforced PMMA composites exhibit good weather resistance. These composite materials can be postformed by thermoforming under pressure, and mechanical properties of postformed products can be improved. The dynamic shear storage and loss modulus (G′, G″) of pultruded glass-fiber-reinforced PMMA composites increased with decreasing pulling rate, and their shear storage moduli are higher than those of pultruded Nylon 6 and polyester composites.     

Manufacturing and mechanical characterization of perforated hybrid composites based on flexible polyurethane foam

This study focused on the fabrication and mechanical evaluation of nonwoven reinforced flexible polyurethane foam composites. Effects of perforation ratio, aperture size, and perforation depth on bursting and low‐velocity impact responses of perforated composite panels were investigated. The nonwoven fabric used for cover sheet was composed of flame retardant polyester, low‐melting point polyester, and recycled Kevlar staple fibers. Blending ratio of Kevlar fiber was confirmed to have relation to mechanical mechanism of cushioning layer. The highest mechanical strength value was obtained at 5 wt % of Kevlar ratio because of the highest cohesive force among recycled Kevlar, flame retardant polyester, and low‐melting point polyester fibers was provided at the blending ratio. The perforated high‐density flexible polyurethane foam composites panel was adhered with intra‐ply hybrid laminates with various areal densities on each face to form sandwich structural composites. The results revealed that perforation ratio and aperture significantly influenced the bursting and low‐velocity impact resistance behaviors of the perforated composites panel. Perforated composites with 10% perforation ratio and 4 mm aperture lead to maximum bursting strength of 437 N. Additional hybrid laminates significantly promoted the maximum bursting strength of the semiperforated hybrid composites by 212%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42288.     

Hybrid effect on mechanical properties of M40‐T300 carbon fiber reinforced Bisphenol A Dicyanate ester composites

Interply and intraply hybrid composites based on Bisphenol A Dicyanate ester (BADCy), high strength carbon fibers T300, and high modulus carbon fibers M40 were prepared by monofilament dip‐winding and press molding technique. The tensile, flexural, interlaminar shear properties and SEM analysis of the hybrid composites with different fiber content and fiber arrangement were investigated. The results indicated that the mechanical properties of intraply hybrid composites were mainly determined by fiber volume contents. When the ratio of fiber volume content was close to 1:1, the intraply hybrid composites possessed lowest tensile and flexural strength. The mechanical properties of interply hybrid composite mainly depended on the fiber arrangement, instead of the fiber volume contents. The hybrid composites using T300 fiber layout as outside layer possessed high flexural strength and low flexural modulus, which was close to that of T300/BADCy composites. The hybrid composites ([(M40)_x/(T300)_y]_S) using M40 fiber layout as outside layer and T300 fibers in the mid‐plane had high flexural modulus and interlaminar shear strength. POLYM. COMPOS., 2010. © 2010 Society of Plastics Engineers     

Mechanical properties of natural fiber hybrid composites based on renewable thermoset resins derived from soybean oil,for use in technical applications

Natural fiber composites are known to have lower mechanical properties than glass or carbon fiber reinforced composites. The hybrid natural fiber composites prepared in this study have relatively good mechanical properties. Different combinations of woven and non‐woven flax fibers were used. The stacking sequence of the fibers was in different orientations, such as 0°, +45°, and 90°. The composites manufactured had good mechanical properties. A tensile strength of about 119 MPa and Young's modulus of about 14 GPa was achieved, with flexural strength and modulus of about 201 MPa and 24 GPa, respectively. For the purposes of comparison, composites were made with a combination of woven fabrics and glass fibers. One ply of a glass fiber mat was sandwiched in the mid‐plane and this increased the tensile strength considerably to 168 MPa. Dynamic mechanical analysis was performed in order to determine the storage and loss modulus and the glass transition temperature of the composites. Microstructural analysis was done with scanning electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011