Tri-Band Bandpass Filter With Sharp Passband Skirts Designed Using Tri-Section SIRs

This letter presents a second-order tri-band bandpass filter (BPF) designed using tri-section stepped-impedance resonators (TSSIRs). The impedance ratios of the TSSIRs were computed using the formulas expressed as functions of the passband center frequencies, which are located at 1.57, 2.45, and 3.5 GHz. A cross-coupled configuration was arranged to sharpen the passband skirts. The newly designed tri-band BPF was verified by circuit implementation and very good agreement between the simulated and measured results was observed.     

Compact multilayer dual-band bandpass filter design using stepped impedance resonators

Compact dual-band bandpass filter (BPF) for the 5th generation mobile communication technology (5G) radio frequency (RF) front-end applications was presented based on multilayer stepped impedance resonators (SIRs). The multilayer dual-band SIR BPF can achieve high selectivity and four transmission zeros (TZs) near the passband edges by the quarter-wavelength tri-section SIRs. The multilayer dual-band SIR BPF is fabricated on a 3-layer FR-4 substrate with a compact dimension of 5.5 mm ×5.0 mm ×1.2 mm. The measured two passbands of themultilayer dual-band SIR BPF are 3.3 GHz -3.5 GHz and 4.8 GHz -5.0 GHz with insertion loss (IL) less than 2 dB respectively. Both measured and simulated results suggest that it is a possible candidate for the application of 5G RF front-end at sub-6 GHz frequency band.     

Wide-stopband microstrip bandpass filters using dissimilar quarter-wavelength stepped-impedance resonators

Wide-stopband and compact microstrip bandpass filters (BPFs) are proposed using various dissimilar quarter-wavelength (/spl lambda//4) stepped-impedance resonators (SIRs) for multiple spurious suppression. The use of /spl lambda//4 SIRs is essential in widening the filter stopband and reducing the circuit size. By properly arranging the individual /spl lambda//4 SIR, which has the same fundamental resonance frequency f/sub 0/, but has different spurious (harmonic) resonance frequencies, and also carefully misaligning the maximum current density nodes, several higher order spurious resonances may be suppressed so that a BPF with wide stopband may be realized. In this study, the basic concept of multiple spurious suppression is demonstrated by thoroughly investigating the spurious characteristics of the fourth-order interdigital BPFs, which consist of two different types of /spl lambda//4 SIRs. To widen the rejection bandwidth, the fourth-order coupled-resonator BPFs based on three and four different types of /spl lambda//4 SIRs are implemented and carefully examined. Specifically, a very wide-stopband microstrip BPF composed of four dissimilar /spl lambda//4 SIRs is realized and its stopband is extended even up to 11.4f/sub 0/ with a rejection level better than 27.5 dB.     

Balanced Dual-Band BPF With Stub-Loaded SIRs for Common-Mode Suppression

A new fourth-order balanced dual-band band-pass filter (BPF) designed using four coupled bi-section half-wavelength ( $lambda /2$) stepped-impedance resonators (SIRs) is presented. To obtain the required differential-mode (DM) operation with suppressed common-mode (CM) transmission, the SIRs were designed to have the same odd-mode, but different even-mode, resonant frequencies. For that purpose, the two inner SIRs were loaded at the center with T-shaped open stubs of different dimensions so that their even-mode resonant frequencies are shifted away from those of the outer SIRs and that their odd-mode ones remain almost intact. For the fabricated prototype BPF, the measured minimum DM insertion losses for the first and second bands are 2.4 and 2.82 dB, respectively, whereas the measured CM insertion loss is larger than 25 dB in 1–7 GHz.      

双频带通滤波器的优化设计

利用阶跃阻抗谐振器优化,设计了一个工作在无线局域网(2.4/5.2GHz)的双频带通滤波器。通过奇、偶模分析,在阶跃阻抗谐振器理论计算公式基础上,根据不同的阻抗比条件,阶跃阻抗谐振器谐振频率比与阶跃阻抗高、低阻抗电长度之比的关系曲线,可以方便地确定阶跃阻抗谐振器的谐振频率和电长度,通过sonnet电路仿真软件验证了设计的合理性,并给出了用于无线通信2.4、5.2 GHz双频带通滤波器的设计结果。该带通滤波器可以分别在2.4、5.2 GHz处得到较好的通带性。由于交叉耦合的存在,该双频带通滤波器在两个通带端各有一个传输零点,以此来提高滤波器的通带频率选择性。最后,测量结果与仿真结果基本吻合。     

Ultra Wideband Bandpass Filter Using Embedded Stepped Impedance Resonators on Multilayer Liquid Crystal Polymer Substrate

This letter proposes an ultra wideband (UWB) bandpass filter (BPF) based on embedded stepped impedance resonators (SIRs). In this study, broad side coupled patches and high impedance microstrip lines are adopted as quasi-lumped elements for realizing the coupling between adjacent SIRs, which are used to suppress stopband harmonic response. An eight-pole UWB BPF is developed from lump-element bandpass prototype and verified by full-wave simulation. The proposed filter is fabricated using multilayer liquid crystal polymer (LCP) process and measured using vector network analyzer. Good agreement between simulated and measured response is observed. The measurement results show that the fabricated filter has a low insertion loss of 0.18 dB at center frequency 6.05 GHz, an ultra wide fractional bandwidth of 127.3% and excellent stopband rejection level higher than 32.01 dB from 10.9 to 18.0 GHz.      

Compact and Low Loss Dual-Band Bandpass Filter Using Pseudo-Interdigital Stepped Impedance Resonators for WLANs

In this letter, pseudo-interdigital stepped impedance resonators (PI-SIRs) are used to design the bandpass filter (BPF) with dual-band response. By tuning the impedance ratio (K) and physical length of SIRs, the BPF has good dual-passband performances at 2.4/5.2GHz and high isolation between the two passbands. It is shown that the dual-band BPF has a smaller area and lower insertion loss in comparison of previous works. Good agreement is shown between the full-wave electromagnetic simulation and the measurement     

Novel design of tri-band bandpass filter based on fractal-shaped geometry of a complementary single split ring resonator

A novel electrically small composite right/left-handed transmission line (CRLH TL) cell based on the Minkowski-shaped geometry of a complementary single split ring resonator is proposed and analysed by the S parameters extraction method. EM simulation results have confirmed the roughly tri-band response of the proposed CRLH TL cell attributed to the fractal multiband nature. A tri-band bandpass filter (BPF) centred at 1.1, 2 and 2.74?GHz with minimum insertion loss 0.4, 1.1 and 1.45?dB was synthesised and fabricated by employing an additional two Hilbert-shaped quarter-wave open-circuit stubs which provided transmission zeros located between passbands to obtain high selectivity. This simple design concept was verified by measurement as well as simulation results.     

Design of the Compact Dual-Band Bandpass Filter With High Isolation for GPS/WLAN Applications

In this letter, a novel compact dual-band bandpass filter (BPF) is designed to achieve the characteristic of low insertion loss and high isolation for global position system (GPS)/wireless local area network (WLAN) applications. This BPF is implemented by properly selecting the impedance ratio (R) and physical length ratio $(alpha)$ of the asymmetric stepped-impedance resonator (SIR) with one step discontinuity. The coupling coefficient between the coupled asymmetric SIRs is calculated by using full-wave simulator IE3D. The proposed filter has very good measured characteristics including a low insertion loss of 1.1 dB for both passbands, a high isolation insertion loss of 55 dB between the two passbands and a wide stopband rejection of 38 dB from 2.7 to 5.3 GHz. Good agreement with responses of electromagnetic (EM) simulation and measurement is compared.      

一种宽阻带带通滤波器的设计方法

基于非相似谐振结构具有不同杂散谐振频率特性,研究并设计了一个具有较高带外抑制特性的微带带通滤波器,提高了微波滤波器的带外抑制特性。首先简要介绍了利用非相似谐振结构抑制寄生通带的原理。尔后,利用ADS软件分别设计了两个分别采用λ4相同谐振结构和λ4非相似谐振结构的滤波器。通过对比,验证了该方法正确性,进一步说明了非相似谐振结构在设计宽阻带、高选择性微带带通滤波器的有效性。     

一种紧凑型微带三频滤波器的设计

提出了一种新型微带三频滤波器,滤波器由两个弯折并相互嵌套的分支线谐振器和一个T形谐振器组成。谐振器之间相互耦合,得到三通带频率响应特性。该滤波器可通过调节微带线几何参数改变通带位置以及带宽,以满足不同应用需求。这种结构的滤波器结构紧凑,电路面积小,三个通带两边各引入一个传输零点,增强了通带间的隔离度以及阻带抑制特性。设计并制作了一款1.57/3.55/5.2GHz三通带滤波器,测试结果与仿真结果基本相符,验证了该滤波器结构的有效性。     

Novel Broadband Bandpass Filters Using Y-Shaped Dual-Mode Microstrip Resonators

A Y-shaped dual-mode microstrip bandpass filter (BPF) with input-output cross-coupling is presented. The characteristic of the Y-shaped dual-mode resonator has been investigated. The resonance frequencies of the degenerate modes can be adjusted easily to satisfy the bandwidth of the BPF. A parallel-coupling feed structure with a cross coupling has been used to generate two transmission zeros at the lower and upper stopband, which can improve the out-of-band performance. A broadband dual-mode microstrip BPF has been designed, fabricated, and measured. The simulated and measured results are in agreement generally. Within the 3.1 to 5.4 GHz bandwidth, the measured insertion loss, return loss and group delay variation are below 0.5 dB, above 15 dB, and below 0.2 ns, respectively.      

Design of compact bandpass filter for WiMAX and UWB application using asymmetric SIRs and DGS

This paper considers a novel compact tri-band microstrip bandpass filter, the design of which employs asymmetric SIRs and DGS for achieving the characteristics of low insertion loss, high selectivity, wider range of bandwidth, and low group delay for 2.5/3.4 GHz (WiMAX) and 4.14–5.32 GHz (UWB) bands. The novel filter design implies the intentional selection of impedance ratio R and the length of the microstrip of asymmetric SIRs; in addition, DGS is used to improve the coupling strength of the last band. The scattering parameters of the three passbands have the following values: insertion losses S₂₁ are–0.26/–0.07/–0.05 dB, and return losses S₁₁ are–11.29/–19.25/–22.64 dB, respectively. The response of the filter was simulated using Ansoft HFSS simulator.     

A Balun-BPF Using a Dual Mode Ring Resonator

In this letter, a Balun-bandpass filter (BPF) is proposed by using a dual-mode ring resonator. The Balun-BPF is not a simply combined or integrated component of a BPF and a Balun but a single BPF with the balun function. We obtained the proper balanced outputs and two-pole BPF characteristic by symmetrically placing the output ports at lambda/2 distance from each other on the dual-mode ring resonator. The fabricated Balun-BPF has a bandwidth of 40 MHz and an insertion loss of 2.4 dB at a center frequency of 2.45 GHz. The differences between the two outputs are 180-184deg in phase and within 1dB in magnitude. The measured frequency responses agree well with simulated ones.     

Microstrip bandpass filters using coupled feed lines for third and fourth generation communications

In this paper, two compact tuneable bandpass filters (BPFs) based on the coupled feed lines are introduced. To approach a compact size, the coupled feed lines are bended. To design a high performance single-band bandpass filter (BPF), coupled feed lines are loaded by T-shaped stubs (as main resonators) and rectangular stubs (as suppressor stubs). Also, the mechanism of coupled feed lines combining with T-shaped open stubs is analyzed to show a tunable passband. The dual-band BPF includes two big radial-stubs, two small radial-stubs, two T-shaped structures and spiral coupled feed lines. The LC model of big radial-stubs is analyzed to compute the equation of transmission zero using its transfer function. The passband frequency of single-band BPF resonates at 2.12 GHz (3G) with corresponded insertion loss of 0.83 dB. Also, for dual-band BPF, the measured insertion-losses of first and second passbands are close to 0.8 and 1.1 dB, respectively. The frequency responses of BPFs are easily adjusted by altering the physical dimensions, demonstrating a adjustable performance. To verify the correct operation of circuits, the proffered filters are implemented and tested.     

A Novel Dual‐Mode Bandpass Filter Based on a Defected Waveguide Resonator

A novel dual‐mode bandpass filter (BPF) using a dual spiral‐shaped defected ground waveguide (DGW) resonator is proposed in this letter. The dual‐mode characteristic of this filter is achieved by loading a defected T‐shaped stub at the midline of the spiral‐shaped DGW resonator. Also, non‐orthogonal input and output feed‐lines are adopted in the filter. Based on the compact DGW structure, a dual‐mode BPF with central frequency of 1.5 GHz for the global positioning system is designed, fabricated, and measured. Measured results agree well with the predicted response and verify the proposed methodology.     

Compact UWB Filter With Double Notch-Bands Using Multilayer LCP Technology

A novel ultra wideband (UWB) bandpass filter with double notch-bands is presented in this paper. Multilayer schematic is adopted to achieve compact size. Stepped impedance resonators (SIRs), which can also suppress harmonic response, are designed on top and second layers, respectively, and broadside coupling technique is used to achieve tight couplings for a wide passband. Folded SIRs that can provide desired notch-bands are designed on the third layer and coupled underneath the second layer SIRs. The designed prototype is fabricated using multilayer liquid crystal polymer (LCP) technology. Good agreement between simulated and measured response is observed. The fabricated filter has dual notch-bands with center frequencies of 6.4/8.0 GHz with 3 dB bandwidths of 9.5%/13.4% and high rejection levels up to 26.4 dB and 43.7 dB at 6.4/8.0 GHz are observed, respectively. It also has low-insertion losses and flat group delay in passbands, and excellent stopband rejection level higher than 30.0 dB from 11.4 GHz to 18.0 GHz.      

Analytical design of a microstrip UWB BPF with sharp rejection

This paper presents a new Ultra-WideBand (UWB) BandPass Filter (BPF) using half-wavelength (??/2) Stepped-Impedance Stub-Loaded Resonator (SISLR). Analytical equations derived by the even-odd mode analysis show the new filter has two tunable transmission zeros at both sides of the passband to provide a sharp rejection and seven transmission poles inside the passband to achieve U.S. UWB performance. For verification, a UWB BPF is designed, fabricated and measured. The measured results show that the fabricated filter has a -3 dB fractional bandwidth from 3.0 GHz to 10.9 GHz and its insertion loss less than 0.9 dB over the whole passband. Furthermore, the new filter exhibits a simple topology, sharp rejection, and deep stopband suppression.     

A Bandpass Filter Design Using Half-Wavelength Stepped Impedance Resonators With Internal Couplings

We propose a new type of microstrip half-wavelength$(lambda/hbox2)$stepped impedance resonator (SIR) for use in bandpass filter (BPF) designs. This$lambda/hbox2$SIR has an internal coupling section that can be used to generate a coupling coefficient in the filter design in addition to couplings between SIRs. It also contains additional stepped impedance lines that shift and suppress the lowest even-mode resonance frequencies to more than what can be achieved by conventional$lambda/hbox2$SIRs. Moreover, a transmission zero is generated close to its fundamental resonance frequency$(f_0)$which can be used in definition of the filter response. A fourth-order microstrip BPF with 10% bandwidth was constructed using two of the proposed$lambda/hbox2$SIRs with a stepped impedance ratio$(R)$of 0.528. The experimental result shows that the filter can achieve low in-band loss and out-of-band attenuation of 52.6dB up to$hbox3f_0$. The lowest spurious resonance frequency is shifted to$hbox3f_0$as opposed to 2.5$f_0$in conventional$lambda/hbox2$SIRs with the same$R$value.     

Design of fractal-based CMOS bandpass filter for WirelessHD system

We proposed a fractal-based dual-mode bandpass filter (BPF) using a standard CMOS process for application of 60 GHz WirelessHD system. We first investigated the effect of coupling feedlines of I/O ports set at different layer of M3 and M4 layer on the transmission loss of the resonator, and verified the nature coupling of fractal-based dual-mode filter. Experimental result shows that the designed filter with a fractional-bandwidth (FBW) of 23%, an insertion loss about 7 dB and return loss larger than 10 dB. Additionally, two transmission zeros are appeared at the passband edges, thus much improve the selectivity of the proposed CMOS BPF. The result indicates that fractal-based structure is feasible and can meet the requirement in the mm-wave application.